Effect of Droplet-Removal Processes on Fog-Harvesting Performance on Wettability-Controlled Wire Array with Staggered Arrangement.

Development of freshwater resources is vital to overcoming severe worldwide water scarcity. Fog harvesting has attracted attention as a candidate technology that can be used to obtain fresh water from a stream of foggy air without energy input. Drainage of captured droplets from fog harvesters is necessary to maintain the permeability of harp-shaped harvesters. In the present study, we investigated the effect of the droplet-removal process on the amount of water harvested using a harvester constructed by wettability-controlled wires with an alternating and staggered arrangement. Droplet transfer from hydrophobic to hydrophilic wires, located upstream and downstream of the fog flow, respectively, was observed with a fog velocity greater than 1.5 m/s. The proportion of harvesting resulting from droplet transfer exceeded 30% of the total, and it reflected more than 20% increase of the harvesting performance compared with that of a harvester with wires of the same wettability: this value varied with the adhesive property of the wires and fog velocity. Scaled-up and multilayered harvesters were developed to enhance harvesting performance. We demonstrated certain enhancements under multilayered conditions and obtained 15.99 g/30 min as the maximum harvested amount, which corresponds to 13.3% of the liquid contained in the fog stream and is enhanced by 10% compared with that without droplet transfer.

Analysis of Evaporation of Droplet Pairs by a Quasi-Steady-State Diffusion Model Coupled with the Evaporative Cooling Effect.

Multidroplet evaporation is a common phase-change phenomenon not only in nature but also in many industrial applications, including inkjet printing and spray cooling. The evaporation behavior of these droplets is strongly affected by the distance between neighboring droplets, and in particular, evaporation suppression occurs as the distance decreases. However, further quantitative information, such as the temperature and local evaporation flux, is limited because the analytical models of multidroplet evaporation only treat vapor diffusion, and the effect of the latent heat transfer through the liquid-vapor phase change is ignored. Here, we perform a numerical analysis of evaporating droplet pairs that linked vapor diffusion from the droplet surface and evaporative cooling. Heat transfer through the liquid and gas phases is also considered because the saturation pressure depends on the temperature. The results show an increase in the vapor concentration in the region between the two droplets. Consequently, the local evaporation flux in the proximate region significantly decreases with decreasing separation distance. This means that the latent heat transfer through the phase change is diminished, and an asymmetrical temperature distribution occurs in the liquid and gas phases. These numerical results provide quantitative information about the temperature and local evaporation flux of evaporating droplet pairs, and they will guide further investigation of multiple droplet evaporation.

Spectral absorptance of a metal-semiconductor-metal thin-multilayer structured thermophotovoltaic cell.

Spectral absorptance of a metal-semiconductor-metal (MSM) thin-multilayer structured thermo-photovoltaic cell was experimentally investigated. A MSM consists of a thin GaSb-semiconductor sandwiched between a top fishnet-type electrode and a flat backside electrode made of gold. A thin GaSb layer was grown on a substrate made of InAs using molecular beam epitaxy, and then all of the InAs substrate was removed using wet etching. The GaSb film was bonded on a surface of gold, which was sputtered on a Si substrate, using a van der Waals bonding method. The top fishnet-type electrode was made using electron beam lithography and a lift-off process. In the case of a 115 nm thick GaSb layer and a square fishnet aperture of a 300 nm × 310 nm size, the spectral absorptance of MSM reached a local peak (95%) at a wavelength of 1.66 µm, which is similar to spectra predicted by numerical simulation. Moreover, the equivalent resonance cavity model and LC circuit model functioned well to indicate the wavelength of several distinct peaks of absorptance.

Droplet motion on a wrinkled PDMS surface with a gradient structural length scale shorter than the droplet diameter.

Droplet transportation using a wettability gradient surface has attracted much attention owing to applications such as in microfluidic devices. A surface with a spatial structural gradient was prepared through a simple and cost-effective process even though understanding of droplet behavior on the structure was still limited. Here, we report impinging droplet motion on a gradient wrinkled surface. Surfaces were prepared through hard film deposition on soft pre-strained polydimethylsiloxane (PDMS) with a mask installed with a slit to control the amount of deposition, which is related to the wavelength of the wrinkles. Droplets were impinged with varying position with respect to the structure, and the droplet motion was observed in the direction away from the region under the slit. We found an asymmetric contact angle and alternate motion on both sides of the three-phase contact line during the motion according to the gradient of the wrinkle wavelength. These results may help not only to understand the behavior of droplet impingement on a gradient structural surface but also to further develop applications using directional droplet transfer.

Wettability Difference Induced Out-of-Plane Unidirectional Droplet Transport for Efficient Fog Harvesting.

Securing freshwater resources is a global issue for ensuring sustainable development. Fog harvesting is attracting great attention as a method to collect water without any energy input. Previous reports that were inspired by insects and plants have given insights such as the effectiveness of in-plane wettability and structural differences for droplet transport, which might enhance artificial water harvesting efficiency. However, further efforts to transfer droplets while maintaining performance are needed because droplet motion owing to these effects is limited to the in-plane direction. In this study, we report droplet transport between three-dimensional copper wire structures with nanostructured hydrophobic and superhydrophilic features. This mechanism enhanced the fog harvesting capability by more than 20% compared with the cumulative value of individual wires. In addition, the relationship between the droplet height and spacing of wires affected the performance. Our results show the importance of out-of-plane directional droplet transport from the wire surface assisted by differences in wire wettability, which minimizes limiting factors of fog harvesting including clogging and droplet shedding. Furthermore, the proposed arrangement reduces the overall system width compared with that of a two-dimensional arrangement while maintaining the amount of harvested water. These results provide a promising approach to designing large-scale and highly efficient fog harvesters.