[Interlaboratory Study on Evaporation Residue Test for Food Contact Products (Report 1)].

An interlaboratory study was performed to evaluate the equivalence between an official method and a modified method of evaporation residue test using three food-simulating solvents (water, 4% acetic acid and 20% ethanol), based on the Japanese Food Sanitation Law for food contact products. Twenty-three laboratories participated, and tested the evaporation residues of nine test solutions as blind duplicates. For evaporation, a water bath was used in the official method, and a hot plate in the modified method. In most laboratories, the test solutions were heated until just prior to evaporation to dryness, and then allowed to dry under residual heat. Statistical analysis revealed that there was no significant difference between the two methods, regardless of the heating equipment used. Accordingly, the modified method provides performance equal to the official method, and is available as an alternative method.

[Interlaboratory Study on Evaporation Residue Test for Food Contact Products (Report 2)].

An interlaboratory study was performed to evaluate the equivalence between an official method and a modified method of evaporation residue test using heptane as a food-simulating solvent for oily or fatty foods, based on the Japanese Food Sanitation Law for food contact products. Twenty-three laboratories participated, and tested the evaporation residues of nine test solutions as blind duplicates. In the official method, heating for evaporation was done with a water bath. In the modified method, a hot plate was used for evaporation, and/or a vacuum concentration procedure was skipped. In most laboratories, the test solutions were heated until just prior to dryness, and then allowed to dry under residual heat. Statistical analysis revealed that there was no significant difference between the two methods. Accordingly, the modified method provides performance equal to the official method, and is available as an alternative method. Furthermore, an interlaboratory study was performed to evaluate and compare two leaching solutions (95% ethanol and isooctane) used as food-simulating solvents for oily or fatty foods in the EU. The results demonstrated that there was no significant difference between heptane and these two leaching solutions.

Interlaboratory Study on Caprolactam Test for Food-Contact Nylon Products.

The Japanese Food Sanitation Law sets a limit on the migration level of caprolactam for food-contacting nylon products. Here, we carried out an interlaboratory study in twenty laboratories to evaluate the performance of the official GC-FID test method and a GC-MS method as an alternative test method to the official method. Each laboratory quantified caprolactam in three test solutions in 20% ethanol as blind duplicates using GC-FID or GC-MS. The official method (GC-FID with absolute calibration) gave trueness, repeatability (RSDr) and reproducibility (RSDr) values of 96-97%, 3.3-5.4% and 4.0-6.7%, respectively. These values met the target criteria (trueness: 80-110%, RSDr: 10%, RSDr: 25%). The performance of the method was further improved by the introduction of heptalactam as an internal standard. As for GC-MS method, some values of the RSDr exceeded 10% when absolute calibration was used. However, when an internal standard was introduced, the trueness, RSDr and RSDr of GC-MS method were all acceptable at 94-96%, 2.0-4.4% and 7.0-9.4%, respectively. Therefore, GC-MS with an internal standard is available as an alternative test method to the official method.

Interlaboratory Study on Volatiles Test for Food-Contacting Polystyrene Products.

Using polystyrene, acrylonitrile-styrene resin and acrylonitrile-butadiene-styrene resin pellets as samples, an interlaboratory study was performed to evaluate the volatiles test method, based on the specifications described in the Japanese Food Sanitation Law for food-contacting polystyrene products. The study was conducted with the participation of twenty-one laboratories. Each laboratory quantified the contents of styrene, toluene, ethylbenzene, isopropylbenzene and propylbenzene in three test pellets using GC-FID, GC-MS or headspace-GC-FID. Statistical analysis revealed that the repeatability (RSDr) and reproducibility (RSDr) were 1.0-2.6 and 2.5-5.5% for the GC-FID method. The values of the performance parameters fulfilled the requirements (RSDr: 10%, RSDr: 25%), and the performance is sufficient for specifications testing. The RSDr and RSDr of results obtained using the GC-MS and HS-GC methods were 1.4-7.8 and 4.9-13%(GC-MS), and 2.0-2.6 and 3.3-6.9%(HS-GC-FID), respectively. The quantified levels were similar to those obtained with GC-FID. The study suggests that the GC-MS and HS-GC methods can be employed as alternative methods to the GC-FID method.

[Interlaboratory study on migration test of antimony and germanium for food-contact polyethylene terephthalate].

An interlaboratory study was performed to evaluate a migration test method of antimony (Sb) and germanium (Ge), based on the Japanese Food Sanitation Law for food- contact polyethylene terephthalate. Eighteen laboratories participated, and quantified Sb and Ge in three test solutions as blind duplicates using graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma-optical emission spectrometry (ICP-OES) or induced coupled plasma-mass spectrometry (ICP-MS). Statistical analysis revealed that the trueness, repeatability and reproducibility were 98-107%, 1.7-7.5% and 2.0-18.8% by using GF-AAS and ICP-OES. The performance of these methods is sufficient for testing the specifications. The performance parameters of ICP-MS were 99-106%, 0.7-2.2% and 2.2-10.5%, respectively. ICP-MS is available as an alternative measuring method. However, in some laboratories, the quantitative values of Sb were higher than the addition levels. We found that Sb in working solutions is absorbed on glass vessels. Careful control of concentration in working solutions is required for Sb analysis.

[Interlaboratory Study on Zinc Test for Food-Contact Rubber Products].

Using six kinds of zinc solution in water and 4% acetic acid as samples, an interlaboratory study was performed to evaluate a zinc (Zn) test method for food-contact rubber products, based on the Japanese Food Sanitation Law. Eighteen laboratories participated, and quantified Zn in six test solutions as blind duplicates using flame atomic absorption spectrometry, induced coupled plasma-optical emission spectrometry or induced coupled plasma-mass spectrometry. Statistical analysis revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 97-103%, 0.7-4.9% and 1.7-8.9% by all measuring methods. The values of the performance parameter fulfilled the target value (trueness: 80-110%, RSDr: 10%, RSDr: 25%). The performance of these methods is sufficient for testing the adherence of samples to the specifications.

[Detection of unexpected recombinant DNA in maize grain].

PCR detection of genetically modified (GM) line-specific recombinant DNA was carried out on Bt 11, Event 176 and Non-GM maize grain harvested in 1999. Of 100 grains of Bt 11 line, Event 176 specific DNA was detected in 11 grains. Of 30 grains of Event 176 line, Mon 810 or Bt 11 specific DNA was detected in 5 grains. In addition, Bt 11 or Event 176 specific DNA was detected in 4 of 30 Non-GM grains. These data suggest that maize grains (not seed) often contain DNAs of different lines from what they were expected to contain. Furthermore, quantitative PCR was performed to estimate the genotype of the Event 176 grains described above. The results showed that the genotype of all the grains containing different recombinant DNA is heterozygous. Therefore, it was considered that the grains containing the unintended recombinant DNA were not accidental contaminants, but that airborne pollination had introduced the recombinant DNA into the grains.

[Interlaboratory study on migration test of cadmium and lead for food contact articles].

An interlaboratory study was performed to evaluate a migration test method of cadmium (Cd) and lead (Pb), based on the Japanese Food Sanitation Law for glassware, ceramicware, enamelware and metal cans. Seventeen laboratories participated, and quantified Cd and Pb in eight test solutions as blind duplicates using flame atomic absorption spectrometry (AAS), graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma-optical emission spectrometry (ICP-OES) or induced coupled plasma-mass spectrometry (ICP-MS). Statistical analysis revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 93-105%, 0.7-8.4% and 2.6-19.3% by using AAS, ICP-OES and ICP-MS (internal standard method). The performance of these methods is sufficient for testing specifications. However, some of the RSDr values exceeded 10% in GF-AAS, and careful control of accuracy is required.

[Performance comparison of material tests for cadmium and lead in food contact plastics].

Based on the Japanese Food Sanitation Law, the performances of official and alternative material test methods for cadmium (Cd) and lead (Pb) in food contact plastics were compared. Nineteen laboratories participated to an interlaboratory study, and quantified Cd and Pb in three PVC pellets. in the official method, a sample is digested with H2SO4, taken up in HCl, and evaporated to dryness on a water bath, then measured by atomic absorption spectrometry (AAS) or inductively coupled plasma-optical emission spectrometry (ICP-OES). Statistical treatment revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 86-95%, 3.1-9.4% and 8.6-22.1%, respectively. The values of the performance parameters fulfilled the requirements , and the performances met the test specifications. The combination of evaporation to dryness on a hot plate and measurement by AAS or ICP-OES is applicable as an alternative method. However, the trueness and RSDr were inferior to those of the official method. The performance parameters obtained by using the microwave digestion method (MW method) to prepare test solution were better than those of the official method. Thus, the MW method is available as an alternative method. Induced coupled plasma-mass spectrometry (ICP-MS) is also available as an alternative method. However, it is necessary to ensure complete digestion of the sample.

Dynamics of radioactive cesium (134Cs and 137Cs) during the milling of contaminated Japanese wheat cultivars and during the cooking of udon noodles made from wheat flour.

The fate of radioactive cesium ((134)Cs plus (137)Cs) during the milling of contaminated Japanese wheat cultivars harvested in FY2011, and during the cooking of Japanese udon noodles made from the wheat flour, was investigated. Grain samples containing various radioactive cesium concentrations (36.6 to 772 Bq/kg [dry weight]) were milled using a laboratory-scale test mill to produce eight fractions: three break flours (1B, 2B, and 3B), three reduction flours (1M, 2M, and 3M), bran, and shorts. The concentrations of radioactive cesium were found to be highest in the bran fractions of all the samples tested, with 2.3- to 2.5-fold higher values than that of the whole grain. Shorts contained radioactive cesium levels similar to that of the whole grain. In contrast, radioactive cesium concentrations in other fractions were found to be less than half the concentration in whole grain. The average processing factor (PF) value calculated for patent flour (0.401 ± 0.048), made from the mixture of 1B, 2B, 1M, and 2M for human consumption, or for low-grade flour (0.467 ± 0.045), made from the mixture of 3B and 3M, was found to be less than 0.5; whereas the average PF value (2.07 ± 0.232) for feed bran (mixture of bran and shorts), which has been used mainly as livestock feed in Japan, was over 2.0. Boiling udon noodles (made from patent flour) resulted in a substantial reduction (>70 % of initial amount) of radioactive cesium. Moreover, radioactive cesium was reduced further (<10 % of the initial amount) in the subsequent rinsing process, and the PF value of boiled noodles was recorded as 0.194. These results demonstrated that patent flour containing radioactive cesium can be made safe for human consumption by adopting the standard limit for radioactive cesium in wheat grain and that radioactive cesium in udon noodles is substantially reduced by cooking.