RESUMEN
A stylized macro-scale energy model of least-cost electricity systems relying only on wind and solar generation was used to assess the value of different storage technologies, individually and combined, for the contiguous U.S. as well as for four geographically diverse U.S. load-balancing regions. For the contiguous U.S. system, at current costs, when only one storage technology was deployed, hydrogen energy storage produced the lowest system costs, due to its energy-capacity costs being the lowest of all storage technologies modeled. Additional hypothetical storage technologies were more cost-competitive than hydrogen (long-duration storage) only at very low energy-capacity costs, but they were more cost-competitive than Li-ion batteries (short-duration storage) at relatively high energy- and power-capacity costs. In all load-balancing regions investigated, the least-cost systems that included long-duration storage had sufficient energy and power capacity to also meet short-duration energy and power storage needs, so that the addition of short-duration storage as a second storage technology did not markedly reduce total system costs. Thus, in electricity systems that rely on wind and solar generation, contingent on social and geographic constraints, long-duration storage may cost-effectively provide the services that would otherwise be provided by shorter-duration storage technologies.
RESUMEN
Solar fuel devices have shown promise as a sustainable source of chemical fuels. However, long-term stability of light absorbing materials remains a substantial barrier to practical devices. Herein, multiple corrosion pathways in 1 M KOH(aq) have been defined for TiO2-protected Si microwire arrays in a polymer membrane either attached to a substrate or free-standing. Top-down corrosion was observed in both morphologies through defects in the TiO2 coating. For the substrate-based samples, bottom-up corrosion was observed through the substrate and up the adjacent wires. In the free-standing samples, uniform bottom-up corrosion was observed through the membrane with all wire material corroded within 10 days of immersion in the dark in 1 M KOH(aq).
RESUMEN
We report herein that synergistic light absorption in the optical near-field enables nanoscale self-organization during inorganic phototropic growth. Se-Te was grown electrochemically under illumination from an incoherent, unstructured light source in geometrically constrained, wavelength scale areas. Despite the limited dimensions, with as few as two discrete features produced in a single sub-micron dimension, the deposit morphology exhibited defined order and anisotropy. Computer modeling analysis of light absorption in simulated structures revealed a synergy wherein light capture in a nanoscale feature was enhanced by the presence of additional adjacent features, with the synergistic effect originating predominantly from nearest neighbor contributions. Modeling moreover indicated that synergistic absorption is produced by scattering of the incident illumination by individual nanoscale features, leading to a local increase in the near-field intensity and consequently increasing the absorption in neighboring features. The interplay between these optical processes establishes the basis for spontaneous order generation via inorganic phototropic growth.
RESUMEN
As reliance on wind and solar power for electricity generation increases, so does the importance of understanding how variability in these resources affects the feasible, cost-effective ways of supplying energy services. We use hourly weather data over multiple decades and historical electricity demand data to analyze the gaps between wind and solar supply and electricity demand for California (CA) and the Western Interconnect (WECC). We quantify the occurrence of resource droughts when the daily power from each resource was less than half of the 39-year daily mean for that day of the year. Averaged over 39 years, CA experienced 6.6 days of solar and 48 days of wind drought per year, compared to 0.41 and 19 for WECC. Using a macro-scale electricity model, we evaluate the potential for both long-term storage and more geographically diverse generation resources to minimize system costs. For wind-solar-battery electricity systems, meeting California demand with WECC generation resources reduces the cost by 9% compared to constraining resources entirely to California. Adding long-duration storage lowers system costs by 21% when treating California as an island. This data-driven analysis quantifies rare weather-related events and provides an understanding that can be used to inform stakeholders in future electricity systems.
Asunto(s)
Energía Solar , Viento , California , Sequías , Electricidad , Energía RenovableRESUMEN
The attachment of the 2,2'-bipyridine (bpy) moieties to the surface of planar silicon(111) (photo)electrodes was investigated using ab initio simulations performed on a new cluster model for methyl-terminated silicon. Density functional theory (B3LYP) with implicit solvation techniques indicated that adventitious chlorine atoms, when present in the organic linker backbone, led to instability at very negative potentials of the surface-modified electrode. In prior experimental work, chlorine atoms were present as a trace surface impurity due to required surface processing chemistry, and thus could plausibly result in the observed surface instability of the linker. Free energy calculations for the Cl-atom release process with model silyl-linker constructs revealed a modest barrier (14.9 kcal mol-1) that decreased as the electrode potential became more negative. A small library of new bpy-derived structures has additionally been explored computationally to identify strategies that could minimize chlorine-induced linker instability. Structures with fluorine substituents are predicted to be more stable than their chlorine analogues, whereas fully non-halogenated structures are predicted to exhibit the highest stability. The behavior of a hydrogen-evolving molecular catalyst Cp*Rh(bpy) (Cp* = pentamethylcyclopentadienyl) immobilized on a silicon(111) cluster was explored theoretically to evaluate differences between the homogeneous and surface-attached behavior of this species in a tautomerization reaction observed under reductive conditions for catalytic H2 evolution. The calculated free energy difference between the tautomers is small, hence the results suggest that use of reductively stable linkers can enable robust attachment of catalysts while maintaining chemical behavior on the electrode similar to that exhibited in homogeneous solution.
RESUMEN
Atomic layer deposition (ALD) on mechanically exfoliated 2D layered materials spontaneously produces network patterns of metal oxide nanoparticles in triangular and linear deposits on the basal surface. The network patterns formed under a range of ALD conditions and were independent of the orientation of the substrate in the ALD reactor. The patterns were produced on MoS2 or HOPG when either tetrakis(dimethylamido)titanium or bis(ethylcyclopentadienyl)manganese were used as precursors, suggesting that the phenomenon is general for 2D materials. Transmission electron microscopy revealed the presence, prior to deposition, of dislocation networks along the basal plane of mechanically exfoliated 2D flakes, indicating that periodical basal plane defects related to disruptions in the van der Waals stacking of layers, such as perfect line dislocations and triangular extended stacking faults networks, introduce a surface reactivity landscape that leads to the emergence of patterned deposition.
RESUMEN
We describe the fabrication and use of arrays of TiO2 nanocones to yield high optical transmission into semiconductor photoelectrodes covered with high surface loadings of light-absorbing electrocatalysts. Covering over 50% of the surface of a light absorber with an array of high-refractive-index TiO2 nanocones imparted antireflective behavior (<5% reflectance) to the surface and allowed >85% transmission of broadband light to the underlying Si, even when thick metal contacts or opaque catalyst coatings were deposited on areas of the light-facing surface that were not directly beneath a nanocone. Three-dimensional full-field electromagnetic simulations for the 400-1100 nm spectral range showed that incident broadband illumination couples to multiple waveguide modes in the TiO2 nanocones, reducing interactions of the light with the metal layer. A proof-of-concept experimental demonstration of light-driven water oxidation was performed using a p+n-Si photoanode decorated with an array of TiO2 nanocones additionally having a Ni catalyst layer electrodeposited onto the areas of the p+n-Si surface left uncovered by the TiO2 nanocones. This photoanode produced a light-limited photocurrent density of â¼28 mA cm-2 under 100 mW cm-2 of simulated air mass 1.5 illumination, equivalent to the photocurrent density expected for a bare planar Si surface even though 54% of the front surface of the Si was covered by an â¼70 nm thick Ni metal layer.
RESUMEN
We describe herein a path-dependent "history" effect wherein the film morphology generated in the second step of a two-step inorganic phototropic growth process depends on a preexisting structure that has been first grown under different optical stimulation conditions. Se-Te generated with static illumination exhibited a highly anisotropic lamellar morphology with a characteristic feature pitch proportional to the input wavelength. Growth using first a short wavelength of light, followed by growth using a longer wavelength, resulted in the second-stage morphology exhibiting termination of lamellae formed during the first growth step. The lamellar pitch at the end of the second growth step was larger than that effected in the first step. In contrast, use of the same input wavelengths but in the opposite order produced no change in the feature pitch but rather only linear feature extension. Analysis of light absorption in simulated structures, in tandem with the empirical data, indicated that the history effect and asymmetric path dependence are a result of emergent nanophotonic processes at the growth interface that dynamically shape the optical field and direct morphological evolution of the photodeposit in a continuous feedback loop.
RESUMEN
Integrated photoelectrochemical devices rely on the synergy between components to efficiently generate sustainable fuels from sunlight. The micro- and/or nanoscale characteristics of the components and their interfaces often control critical processes of the device, such as charge-carrier generation, electron and ion transport, surface potentials, and electrocatalysis. Understanding the spatial properties and structure-property relationships of these components can provide insight into designing scalable and efficient solar fuel components and systems. These processes can be probed ex situ or in situ with nanometer-scale spatial resolution using emerging scanning-probe techniques based on atomic force microscopy (AFM). In this Perspective, we summarize recent developments of AFM-based techniques relevant to solar fuel research. We review recent progress in AFM for (1) steady-state and dynamic light-induced surface photovoltage measurements; (2) nanoelectrical conductive measurements to resolve charge-carrier heterogeneity and junction energetics; (3) operando investigations of morphological changes, as well as surface electrochemical potentials, currents, and photovoltages in liquids. Opportunities for research include: (1) control of ambient conditions for performing AFM measurements; (2) in situ visualization of corrosion and morphological evolution of electrodes; (3) operando AFM techniques to allow nanoscale mapping of local catalytic activities and photo-induced currents and potentials.
RESUMEN
The long-range order of anisotropic phototropic Se-Te films grown electrochemically at room temperature under uniform-intensity, polarized, incoherent, near-IR illumination has been investigated using crystalline (111)-oriented Si substrates doped degenerately with either p- or n-type dopants. Fourier-transform (FT) analysis was performed on large-area images obtained with a scanning electron microscope, and peak shapes in the FT spectra were used to determine the pattern fidelity in the deposited Se-Te films. Under nominally identical illumination conditions, phototropic films grown on p+-Si(111) exhibited a higher degree of anisotropy and a more well-defined pattern period than phototropic films grown on n+-Si(111). Similar differences in the phototropic Se-Te deposit morphology and pattern fidelity on p+-Si versus n+-Si were observed when the deposition rate and current densities were controlled for by adjusting the deposition parameters and illumination conditions. The doping-related effects of the Si substrate on the pattern fidelity of the phototropic Se-Te deposits are ascribable to an electrical effect produced by the different interfacial junction energetics between Se-Te and p+-Si versus n+-Si that influences the dynamic behavior during phototropic growth at the Se-Te/Si interface.
RESUMEN
Photoelectrochemical deposition of Se-Te on isolated Au islands using an unstructured, incoherent beam of light produces growth of Se-Te alloy toward the direction of the incident light beam. Full-wave electromagnetic simulations of light absorption indicated that the induced spatial growth anisotropy was a function of asymmetric absorption in the evolving deposit. Inorganic phototropic growth is analogous to biological systems such as palm trees that exhibit phototropic growth wherein physical extension of the plant guides the crown toward the time-averaged position of the sun, to maximize solar harvesting.
Asunto(s)
Galvanoplastia , Selenio/química , Telurio/química , Electroquímica , Procesos FotoquímicosRESUMEN
Highly periodic, geometrically directed, anisotropic Se-Pb films have been synthesized at room temperature from an isotropic aqueous solution without the use of physical templates by photoelectrodeposition using a series of discrete input illumination polarizations and wavelengths from an unstructured, uncorrelated, incoherent light source. Dark growth did not generate deposits with substantial long-range order, but growth using unpolarized illumination resulted in an ordered, nanoscale, mesh-type morphology. Linearly polarized illumination generated Se-Pb deposits that displayed an ordered, highly anisotropic lamellar pattern wherein the long axes of the lamellae were aligned parallel to the light polarization vector. The pitch of the lamellar features was proportional to the input light wavelength, as confirmed by Fourier analysis. Full-wave electromagnetic and Monte Carlo growth simulations that incorporated only the fundamental light-matter interactions during growth successfully reproduced the experimentally observed morphologies and quantitatively matched the pattern periodicities. Electrochemical postprocessing of the as-deposited Se-Pb structures resulted in the generation of stoichiometric, crystalline PbSe while preserving the nanopatterned morphology, thus broadening the genus of materials that can be prepared with controlled three-dimensional morphologies through maskless photoelectrodeposition.
RESUMEN
Reactively sputtered nickel oxide (NiOx) films provide transparent, antireflective, electrically conductive, chemically stable coatings that also are highly active electrocatalysts for the oxidation of water to O2(g). These NiOx coatings provide protective layers on a variety of technologically important semiconducting photoanodes, including textured crystalline Si passivated by amorphous silicon, crystalline n-type cadmium telluride, and hydrogenated amorphous silicon. Under anodic operation in 1.0 M aqueous potassium hydroxide (pH 14) in the presence of simulated sunlight, the NiOx films stabilized all of these self-passivating, high-efficiency semiconducting photoelectrodes for >100 h of sustained, quantitative solar-driven oxidation of water to O2(g).
RESUMEN
A hybrid photoanode based on a molecular water oxidation precatalyst was prepared from TiO2-protected n- or p+-Si coated with multiwalled carbon nanotubes (CNT) and the ruthenium-based water oxidation precatalyst [RuIV(tda)(py-pyr)2(O)], 1(O) (tda2- is [2,2':6',2â³-terpyridine]-6,6â³-dicarboxylato and py-pir is 4-(pyren-1-yl)-N-(pyridin-4-ylmethyl)butanamide). The Ru complex was immobilized by π-π stacking onto CNTs that had been deposited by drop casting onto Si electrodes coated with 60 nm of amorphous TiO2 and 20 nm of a layer of sputtered C. At pH = 7 with 3 Sun illumination, the n-Si/TiO2/C/CNT/[1+1(O)] electrodes exhibited current densities of 1 mA cm-2 at 1.07 V vs NHE. The current density was maintained for >200 min at a constant potential while intermittently collecting voltammograms that indicated that over half of the Ru was still in molecular form after O2 evolution.
RESUMEN
Transition metal phosphides exhibit high catalytic activity toward the electrochemical hydrogen-evolution reaction (HER) and resist chemical corrosion in acidic solutions. For example, an electrodeposited CoP catalyst exhibited an overpotential, η, of -η < 100 mV at a current density of -10 mA cm-2 in 0.500 M H2SO4(aq). To obtain a chemical description of the material as-prepared and also while effecting the HER in acidic media, such electrocatalyst films were investigated using Raman spectroscopy and X-ray absorption spectroscopy both ex situ as well as under in situ and operando conditions in 0.500 M H2SO4(aq). Ex situ analysis using the tandem spectroscopies indicated the presence of multiple ordered and disordered phases that contained both near-zerovalent and oxidized Co species, in addition to reduced and oxygenated P species. Operando analysis indicated that the active electrocatalyst was primarily amorphous and predominantly consisted of near-zerovalent Co as well as reduced P.
Asunto(s)
Cobalto/química , Técnicas Electroquímicas , Hidrógeno/química , Fósforo/química , Catálisis , Espectroscopía de Absorción de Rayos XRESUMEN
Au was photoelectrochemically deposited onto cylindrical or tapered p-Si microwires on Si substrates to profile the photoinduced charge-carrier generation in individual wires in a photoactive semiconductor wire array. Similar experiments were repeated for otherwise identical Si microwires doped to be n-type. The metal plating profile was conformal for n-type wires, but for p-type wires was a function of distance from the substrate and was dependent on the illumination wavelength. Spatially resolved charge-carrier generation profiles were computed using full-wave electromagnetic simulations, and the localization of the deposition at the p-type wire surfaces observed experimentally correlated well with the regions of enhanced calculated carrier generation in the volumes of the microwires. This technique could potentially be extended to determine the spatially resolved carrier generation profiles in a variety of mesostructured, photoactive semiconductors.
RESUMEN
Highly anisotropic and ordered nanoscale lamellar morphologies can be spontaneously generated over macroscopic areas, without the use of a photomask or any templating agents, via the photoelectrodeposition of Se-Te alloy films. To form such structures, the light source can be a single, linearly polarized light source that need not necessarily be highly coherent. In this work, the variation in the morphologies produced by this deposition process was evaluated in response to differences in the coherence and relative phase between multiple simultaneous linearly polarized illumination inputs. Specifically, the morphologies of photoelectrodeposits were evaluated when two tandem same-wavelength sources with discrete linear polarizations, both either mutually incoherent or mutually coherent (with defined phase differences), were used. Additionally, morphologies were simulated via computer modeling of the interfacial light scattering and absorption during the photoelectrochemical growth process. The morphologies that were generated using two coherent, in-phase sources were equivalent to those generated using only a single source. In contrast, the use of two coherent, out-of-phase sources produced a range of morphological patterns. For small out-of-phase addition of orthogonal polarization components, lamellar-type patterns were observed. When fully out-of-phase orthogonal sources (circular polarization) were used, an isotropic, mesh-type pattern was instead generated, similar to that observed when unpolarized illumination was utilized. In intermediate cases, anisotropic lamellar-type patterns were superimposed on the isotropic mesh-type patterns, and the relative height between the two structures scaled with the amount of out-of-phase addition of the orthogonal polarization components. Similar results were obtained when two incoherent sources were utilized. In every case, the long axis of the lamellar-type morphology component aligned parallel to the intensity-weighted average polarization orientation. The observations consistently agreed with computer simulations, indicating that the observed morphologies were fully determined by the nature of the illumination utilized during the growth process. The collective data thus indicated that the photoelectrodeposition process exhibits sensitivity toward the coherency, relative phase, and polarization orientations of all optical inputs and that this sensitivity is physically expressed in the morphology of the deposit.
RESUMEN
The behavior of n-Si(111) photoanodes covered by monolayer sheets of fluorinated graphene (F-Gr) was investigated under a range of chemical and electrochemical conditions. The electrochemical behavior of n-Si/F-Gr and np(+)-Si/F-Gr photoanodes was compared to hydride-terminated n-Si (n-Si-H) and np(+)-Si-H electrodes in contact with aqueous Fe(CN)6(3-/4-) and Br2/HBr electrolytes as well as in contact with a series of outer-sphere, one-electron redox couples in nonaqueous electrolytes. Illuminated n-Si/F-Gr and np(+)-Si/F-Gr electrodes in contact with an aqueous K3(Fe(CN)6/K4(Fe(CN)6 solutions exhibited stable short-circuit photocurrent densities of â¼10 mA cm(-2) for 100,000 s (>24 h), in comparison to bare Si electrodes, which yielded nearly a complete photocurrent decay over â¼100 s. X-ray photoelectron spectra collected before and after exposure to aqueous anodic conditions showed that oxide formation at the Si surface was significantly inhibited for Si electrodes coated with F-Gr relative to bare Si electrodes exposed to the same conditions. The variation of the open-circuit potential for n-Si/F-Gr in contact with a series of nonaqueous electrolytes of varying reduction potential indicated that the n-Si/F-Gr did not form a buried junction with respect to the solution contact. Further, illuminated n-Si/F-Gr electrodes in contact with Br2/HBr(aq) were significantly more electrochemically stable than n-Si-H electrodes, and n-Si/F-Gr electrodes coupled to a Pt catalyst exhibited ideal regenerative cell efficiencies of up to 5% for the oxidation of Br(-) to Br2.
RESUMEN
Fundamental details concerning the interaction between H2 and CH3-Si(111) have been elucidated by the combination of diffractive scattering experiments and electronic structure and scattering calculations. Rotationally inelastic diffraction (RID) of H2 and D2 from this model hydrocarbon-decorated semiconductor interface has been confirmed for the first time via both time-of-flight and diffraction measurements, with modest j = 0 â 2 RID intensities for H2 compared to the strong RID features observed for D2 over a large range of kinematic scattering conditions along two high-symmetry azimuthal directions. The Debye-Waller model was applied to the thermal attenuation of diffraction peaks, allowing for precise determination of the RID probabilities by accounting for incoherent motion of the CH3-Si(111) surface atoms. The probabilities of rotationally inelastic diffraction of H2 and D2 have been quantitatively evaluated as a function of beam energy and scattering angle, and have been compared with complementary electronic structure and scattering calculations to provide insight into the interaction potential between H2 (D2) and hence the surface charge density distribution. Specifically, a six-dimensional potential energy surface (PES), describing the electronic structure of the H2(D2)/CH3-Si(111) system, has been computed based on interpolation of density functional theory energies. Quantum and classical dynamics simulations have allowed for an assessment of the accuracy of the PES, and subsequently for identification of the features of the PES that serve as classical turning points. A close scrutiny of the PES reveals the highly anisotropic character of the interaction potential at these turning points. This combination of experiment and theory provides new and important details about the interaction of H2 with a hybrid organic-semiconductor interface, which can be used to further investigate energy flow in technologically relevant systems.
RESUMEN
Photoresponsive materials that adapt their morphologies, growth directions, and growth rates dynamically in response to the local incident electromagnetic field would provide a remarkable route to the synthesis of complex 3D mesostructures via feedback between illumination and the structure that develops under optical excitation. We report the spontaneous development of ordered, nanoscale lamellar patterns in electrodeposited selenium-tellurium (Se-Te) alloy films grown under noncoherent, uniform illumination on unpatterned substrates in an isotropic electrolyte solution. These inorganic nanostructures exhibited phototropic growth in which lamellar stripes grew toward the incident light source, adopted an orientation parallel to the light polarization direction with a period controlled by the illumination wavelength, and showed an increased growth rate with increasing light intensity. Furthermore, the patterns responded dynamically to changes during growth in the polarization, wavelength, and angle of the incident light, enabling the template-free and pattern-free synthesis, on a variety of substrates, of woodpile, spiral, branched, or zigzag structures, along with dynamically directed growth toward a noncoherent, uniform intensity light source. Full-wave electromagnetic simulations in combination with Monte Carlo growth simulations were used to model light-matter interactions in the Se-Te films and produced a model for the morphological evolution of the lamellar structures under phototropic growth conditions. The experiments and simulations are consistent with a phototropic growth mechanism in which the optical near-field intensity profile selects and reinforces the dominant morphological mode in the emergent nanoscale patterns.