Ultra-Sensitive and Selective Detection of Arsenic(III) via Electroanalysis over Cobalt Single-Atom Catalysts.

Achieving highly sensitive and selective detection of trace-level As(III) and clarifying the underlying mechanism is still a intractable problem. The electroanalysis of As(III) relies on the electrocatalytic ability of the sensing interface. Herein, we first adopt single-atom catalysts as the electrocatalyst in As(III) detection. Cobalt single-atoms anchored on nitrogen-doped carbon material (Co SAC) were found to have an extraordinary sensitivity of 11.44 µA ppb-1 with excellent stability and repeatability, which so far is the highest among non-noble metal nanomaterials. Co SAC also exhibited a superior selectivity toward As(III) compared with some bivalent heavy metal ions (HMIs). Combining X-ray absorption spectroscopy (XAFS), density functional theory (DFT) calculation, and reaction kinetics simulation, we demonstrated that Co single atoms stabilized in N2C2 support serve as active sites to catalyze H3AsO3 reduction via the formation of Co-O hybridization bond, leading to a lower energy barrier, promoting the breakage of As-O bonds. Importantly, the first electron transfer is the rate-limiting step of arsenic reduction and is found to be more favorable on Co-SAC both thermodynamically and kinetically. This work not only expands the potential applicaiton of single-atom catalysts in the detection and treatment of As(III), but also provides atomic-level catalytic insights into HMIs sensing interfaces.

Identifying Phase-Dependent Electrochemical Stripping Performance of FeOOH Nanorod: Evidence from Kinetic Simulation and Analyte-Material Interactions.

Metal hydroxide nanomaterials are widely applied in the energy and environment fields. The electrochemical performance of such materials is strongly dependent on their crystal phases. However, as there are always multiple factors relating to the phase-dependent electrochemistry, it is still difficult to identify the determining one. The well-defined crystal phases of α- and ß-FeOOH nanorods are characterized through the transmission electron microscopy by a series of rotation toward one rod, where the cross-section shape and the growth direction along the [001] crystalline are first verified for 1D FeOOH nanostructures. The electrosensitivity of the two materials toward Pb(II) is tested, where α-FeOOH performs an outstanding sensitivity whilst it is only modest for ß-FeOOH. Experiments via Fourier transform infrared spectroscopy, X-ray absorption fine structure (XAFS), etc., show that α-FeOOH presents a larger Pb(II) adsorption capacity due to more surficial hydroxyl groups and weaker PbO bond strength. The reaction kinetics are simulated and the adsorption capacity is found to be the determining factor for the distinct Pb(II) sensitivities. Combining experiment with simulation, this work reveals the physical insights of the phase-dependent electrochemistry for FeOOH and provides guidelines for the functional application of metal hydroxide nanomaterials.

Noble-Metal-Free Co0.6Fe2.4O4 Nanocubes Self-Assembly Monolayer for Highly Sensitive Electrochemical Detection of As(III) Based on Surface Defects.

Nanocrystals generally suffer from agglomeration because of the spontaneous reduction of the system surface energy, resulting in blocking the active sites from reacting with target ions, and then severely reducing the electrochemical sensitivity. In this article, a highly ordered self-assembled monolayer array is successfully constructed using ∼14 nm Co0.6Fe2.4O4 nanocubes uniformly and controllably distributed on the surface of a working electrode (glass carbon plate). The large area and high exposure of the surface defects on Co0.6Fe2.4O4 nanocubes are clearly characterized by high-resolution transmission electron microscopy (HRTEM) and atomic-resolution high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM). Expectedly, a considerable sensitivity of 2.12 µA ppb-1 and a low limit of detection of 0.093 ppb are achieved for As(III) detection on this highly homogeneous sensing interface; this excellent electroanalysis performance is even better than that of noble metals electrodes. Most importantly, this approach of uniformly distributing the small-sized defective nanoparticles on the electrode surface provides a new opportunity for modifying the electrodes, as well as the realization of their applications in the field of environmental electroanalysis for heavy metal ions.

Surface Fe(II)/Fe(III) Cycle Promoted Ultra-Highly Sensitive Electrochemical Sensing of Arsenic(III) with Dumbbell-Like Au/Fe3O4 Nanoparticles.

Developing a new ultrasensitive interface to detect As(III) is highly desirable because of its seriously toxic and low concentration in drinking water. Recently, Fe3O4 nanoparticles of high adsorption toward As(III) become very promising to be such an interface, which is still limited by the poor understanding of their surface physicochemical properties. Herein, we report that dumbbell-like Au/Fe3O4 nanoparticles, when being modified the screen-printed carbon electrode, can serve as an efficient sensing interface for As(III) detection with an excellent sensitivity of 9.43 µA ppb-1 and a low detection limit of 0.0215 ppb. These outstanding records were attributed to the participation of Fe(II)/Fe(III) cycle on Fe3O4 surface in the electrochemical reaction of As(III) redox, as revealed by X-ray photoelectron spectroscopy, X-ray absorption near edge structure, and extended X-ray absorption fine structure. This work provides new insight into the mechanism of electroanalysis from the viewpoint of surface active atoms, and also helps to predict the construction of ultrahighly sensitive electrochemical sensors for other heavy metal ions with nonprecious redox active materials.

High Electrochemical Sensitivity of TiO2- x Nanosheets and an Electron-Induced Mutual Interference Effect toward Heavy Metal Ions Demonstrated Using X-ray Absorption Fine Structure Spectra.

Mutual interference is a severe issue that occurs during the electrochemical detection of heavy metal ions. This limitation presents a notable drawback for its high sensitivity to specific targets. Here, we present a high electrochemical sensitivity of ∼237.1 µA cm-2 µM-1 toward copper(II) [Cu(II)] based on oxygen-deficient titanium dioxide (TiO2- x) nanosheets. We fully demonstrated an atomic-level relationship between electrochemical behaviors and the key factors, including the high-energy (001) facet percentage, oxygen vacancy concentration, surface -OH content, and charge carrier density, is fully demonstrated. These four factors were quantified using Raman, electron spin resonance, X-ray photoelectron spectroscopy spectra, and Mott-Schottky plots. In the mutual interference investigation, we selected cadmium(II) [Cd(II)] as the target ion because of the significant difference in its stripping potential (∼700 mV). The results show that the Cd(II) can enhance the sensitivity of TiO2- x nanosheets toward Cu(II), exhibiting an electron-induced mutual interference effect, as demonstrated by X-ray absorption fine structure spectra.

Size-tunable Ag nanoparticles sensitized porous ZnO nanobelts: controllably partial cation-exchange synthesis and selective sensing toward acetic acid.

Porous ZnO nanobelts sensitized with Ag nanoparticles have been prepared via a partial cation-exchange reaction assisted by a thermal oxidation treatment, employing ZnSe·0.5N2H4 nanobelts as precursors. After partially exchanged with Ag+ cations, the belt-like morphology of the precursors is still preserved. Continuously calcined in air, they are in situ transformed into Ag nanoparticles sensitized porous ZnO nanobelts. The size of the Ag nanoparticles can be tuned through manipulating the amount of exchanging Ag+ cations. Considering the porous and belt-like nanostructure, sensing characteristics of ZnO and the catalytic activity of Ag nanoparticles, the gas sensing performances of the as-prepared Ag nanoparticles sensitized porous ZnO nanobelts have been carefully investigated. The results indicate that Ag nanoparticles significantly enhance the sensing performances of porous ZnO nanobelts toward typical volatile organic compounds. Especially, a good selectivity has been demonstrated toward acetic acid gas with a low detection limit less than 1 ppm. Furthermore, they also display a good reproducibility with a short response/recovery time due to the thin, uniform and porous sensing film, which is fabricated with the assembled technique and in situ calcined approach. Finally, their sensing mechanism has been further discussed.

Surface-Electronic-State-Modulated, Single-Crystalline (001) TiO2 Nanosheets for Sensitive Electrochemical Sensing of Heavy-Metal Ions.

Intrinsically low conductivity and poor reactivity restrict many semiconductors from electrochemical detection. Usually, metal- and carbon-based modifications of semiconductors are necessary, making them complex, expensive, and unstable. Here, for the first time, we present a surface-electronic-state-modulation-based concept applied to semiconductors. This concept enables pure semiconductors to be directly available for ultrasensitive electrochemical detection of heavy-metal ions without any modifications. As an example, a defective single-crystalline (001) TiO2 nanosheet exhibits high electrochemical performance toward Hg(II), including a sensitivity of 270.83 µA µM-1 cm-2 and a detection limit of 0.017 µM, which is lower than the safety standard (0.03 µM) of drinking water established by the World Health Organization (WHO). It has been confirmed that the surface oxygen vacancy adsorbs an O2 molecule while the Ti3+ donates an electron, forming the O2•- species that facilitate adsorption of Hg(II) and serve as active sites for electron transfer. These findings not only extend the electrochemical sensing applications of pure semiconductors but also stimulate new opportunities for investigating atom-level electrochemical behaviors of semiconductors by surface electronic-state modulation.

Tin Oxide Crystals Exposed by Low-Energy {110} Facets for Enhanced Electrochemical Heavy Metal Ions Sensing: X-ray Absorption Fine Structure Experimental Combined with Density-Functional Theory Evidence.

Herein, we revealed that the electrochemical behaviors on the detection of heavy metal ions (HMIs) would largely rely on the exposed facets of SnO2 nanoparticles. Compared to the high-energy {221} facet, the low-energy {110} facet of SnO2 possessed better electrochemical performance. The adsorption/desorption tests, density-functional theory (DFT) calculations, and X-ray absorption fine structure (XAFS) studies showed that the lower barrier energy of surface diffusion on {110} facet was critical for the superior electrochemical property, which was favorable for the ions diffusion on the electrode, and further leading the enhanced electrochemical performance. Through the combination of experiments and theoretical calculations, a reliable interpretation of the mechanism for electroanalysis of HMIs with nanomaterials exposed by different crystal facets has been provided. Furthermore, it provides a deep insight into understanding the key factor to improve the electrochemical performance for HMIs detection, so as to design high-performance electrochemical sensors.

In Situ Underwater Laser-Induced Breakdown Spectroscopy Analysis for Trace Cr(VI) in Aqueous Solution Supported by Electrosorption Enrichment and a Gas-Assisted Localized Liquid Discharge Apparatus.

Traditional laser-induced breakdown spectroscopy (LIBS) always fails to directly detect target in aqueous solution due to rapid quenching of emitted light and adsorption of pulse energy by surrounding water. A method is proposed for the in situ underwater LIBS analysis of Cr(VI) in aqueous solution freed from the common problems mentioned above by combining a gas-assisted localized liquid discharge apparatus with electrosorption for the first time. In this approach, the introduction of the gas-assisted localized liquid discharge apparatus provides an instantaneous gaseous environment for underwater LIBS measurement (that is, the transfer of sampling matrix is not needed from aqueous solution to dry state). The preconcentration of Cr(VI) is achieved by electrosorption with a positive potential applied around adsorbents, which can promote the adsorption of Cr(VI) and inhibit that of the coexisting cations leading to a good anti-interference. Amino groups functionalized chitosan-modified graphene oxide (CS-GO) is utilized for Cr(VI) enrichment, which can be protonated to form NH3+ in acidic condition promoting the adsorption toward Cr(VI) by electrostatic attraction. The highest detection sensitivity of 5.15 counts µg-1 L toward Cr(VI) is found for the optimized electrosorption potential (EES = 1.5 V) and electrosorption time (tES = 600 s) without interference from coexisting metal ions. A corresponding limit of detection (LOD) of 12.3 µg L-1 (3σ method) is achieved, which is amazingly improved by 2 or even 3 orders of magnitude compared to the previous reports of LIBS.

Adsorbent Assisted in Situ Electrocatalysis: An Ultra-Sensitive Detection of As(III) in Water at Fe3O4 Nanosphere Densely Decorated with Au Nanoparticles.

Most gold nanoparticle-based electrodes have been utilized for the analysis of highly toxic As(III), while nano-Fe3O4 materials are currently attracting considerable interest as an adsorbent for the removal of As(III). However, the combination of gold nanoparticles with Fe3O4 nanoadsorbents for stripping voltammetry is, to the best of our knowledge, unexplored. Here, a sensing interface for ultrasensitive detection of As(III) is designed and constructed by abundantly dispersing Au nanoparticles (Au NPs) on the surface of the Fe3O4 nanosphere. The Au@Fe3O4 nanospheres are covered by the room temperature ionic liquid (RTIL) and then modified on the screen-printed carbon electrode (SPCE). By combining the excellent catalytic properties of the Au nanoparticles (∼3-9 nm in diameter) with the good adsorption capacity of Fe3O4 nanospheres toward As(III), as well as the good conductivity of RTIL, the Au@Fe3O4-RTIL shows excellent performance in the detection of arsenic under nearly neutral conditions without modifying the morphology of the sensing interface. Through optimization of the experimental conditions, an ultrahigh sensitivity of 458.66 µA ppb(-1) cm(-2) from 0.1 to 1 ppb with a detection limit (3σ method) of 0.0022 ppb was obtained. The reproducibility and reliability of the Au@Fe3O4-RTIL sensing interface was also evaluated with good results. Finally, we used this platform to analyze real samples.

Electrochemical Detection of Trace Arsenic(III) by Nanocomposite of Nanorod-Like α-MnO2 Decorated with ∼5 nm Au Nanoparticles: Considering the Change of Arsenic Speciation.

It has been reported that the majority of groundwater shows weak alkaline in which the As(III) species would be present as neutral H3AsO3 species and ionized H2AsO3- species. However, as most reported previously, electrochemical detection of As(III) has been operated under acidic conditions and the nonionic As(III) (H3AsO3) is the dominant species. Therefore, considering the change of As(III) speciation in different pH conditions, to develop a reliable method for the detection of As(III) in alkaline media might be more meaningful for practical applications. Here, combined the multilayer adsorption of nanorod-like α-MnO2 with the excellent electrocatalytic ability of ∼5 nm Au nanoparticles (AuNPs), an efficient and ultrahigh anti-interference electrochemical detection of As(III) with AuNPs/α-MnO2 nanocomposite in alkaline media (nearly real water environment) was developed. Notably, we have provided a thorough electrochemical analytical investigation to confirm the advantage of As(III) detection in alkaline media. The system was evaluated by a series of interference tests, and no obvious interference from commonly coexisting substances (referring to the groundwater, Togtoh region, Inner Mongolia, China) was observed in alkaline media. Furthermore, electrodes robust stability and excellent reproducibility were obtained. Under the optimized conditions, the limit of detection (3σ method) toward As(III) was 0.019 ppb, and the obtained sensitivity was 16.268 ± 0.242 µA ppb-1 cm-2. Finally, the proposed method has been successfully employed for detection of As(III) in a real water sample.

Iron Oxide with Different Crystal Phases (α- and γ-Fe2O3) in Electroanalysis and Ultrasensitive and Selective Detection of Lead(II): An Advancing Approach Using XPS and EXAFS.

Iron oxide with different crystal phases (α- and γ-Fe2O3) has been applied to electrode coatings and been demonstrated to ultrasensitive and selective electrochemical sensing toward heavy metal ions (e.g., Pb(II)). A range of Pb(II) contents in micromoles (0.1 to 1.0 µM) at α-Fe2O3 nanoflowers with a sensitivity of 137.23 µA µM(-1) cm(-2) and nanomoles (from 0.1 to 1.0 nM) at γ-Fe2O3 nanoflowers with a sensitivity of 197.82 µA nM(-1) cm(-2) have been investigated. Furthermore, an extended X-ray absorption fine structure (EXAFS) technique was applied to characterize the difference of local structural environment of the adsorbed Pb(II) on the surface of α- and γ-Fe2O3. The results first showed that α- and γ-Fe2O3 had diverse interaction between Pb(II) and iron (hydro)oxides, which were consistent with the difference of electrochemical performance. Determining the responses of Cu(II) and Hg(II) as the most appropriate choice for comparison, the stripping voltammetric quantification of Pb(II) with high sensitivity and selectivity at γ-Fe2O3 nanoflower has been demonstrated. This work reveals that the stripping performances of a nanomodifier have to be directly connected with its intrinsic surface atom arrangement.

Porous and single-crystalline ZnO nanobelts: fabrication with annealing precursor nanobelts, and gas-sensing and optoelectronic performance.

Porous and single-crystalline ZnO nanobelts have been prepared through annealing precursors of ZnSe · 0.5N2H4 well-defined and smooth nanobelts, which have been synthesized via a simple hydrothermal method. The composition and morphology evolutions with the calcination temperatures have been investigated in detail for as-prepared precursor nanobelts, suggesting that they can be easily transformed into ZnO nanobelts by preserving their initial morphology via calcination in air. In contrast, the obtained ZnO nanobelts are densely porous, owing to the thermal decomposition and oxidization of the precursor nanobelts. More importantly, the achieved porous ZnO nanobelts are single-crystalline, different from previously reported ones. Motivated by the intrinsic properties of the porous structure and good electronic transporting ability of single crystals, their gas-sensing performance has been further explored. It is demonstrated that porous ZnO single-crystalline nanobelts exhibit high response and repeatability toward volatile organic compounds, such as ethanol and acetone, with a short response/recovery time. Furthermore, their optoelectronic behaviors indicate that they can be promisingly employed to fabricate photoelectrochemical sensors.

Electroadsorption-assisted direct determination of trace arsenic without interference using transmission X-ray fluorescence spectroscopy.

An analytical technique based on electroadsorption and transmission X-ray fluorescence (XRF) for the quantitative determination of arsenic in aqueous solution with ppb-level limits of detection (LOD) is proposed. The approach uses electroadsorption to enhance the sensitivity and LOD of the arsenic XRF response. Amine-functionalized carbonaceous microspheres (NH2-CMSs) are found to be the ideal materials for both the quantitative adsorption of arsenic and XRF analysis due to the basic amine sites on the surface and their noninterference in the XRF spectrum. In electroadsorptive X-ray fluorescence (EA-XRF), arsenic is preconcentrated by a conventional three-electrode system with a positive electricity field around the adsorbents. Then, the quantification of arsenic on the adsorbents is achieved using XRF. The electroadsorption preconcentration can realize the fast transfer of arsenic from the solution to the adsorbents and improve the LOD of conventional XRF compared with directly determining arsenic solution by XRF alone. The sensitivity of 0.09 cnt ppb(-1) is obtained without the interferences from coexisted metal ions in the determination of arsenic, and the LOD is found to be 7 ppb, which is lower than the arsenic guideline value of 10 ppb given by the World Health Organization (WHO). These results demonstrated that XRF coupled with electroadsorption was able to determine trace arsenic in real water sample.

Cation Exchange Synthesis and Unusual Resistive Switching Behaviors of Ag2Se Nanobelts.

Ag2Se nanobelts are prepared through employing ZnSe nanobelts as templates via a facile cation exchange approach. The templates are derived from precursor ZnSe·0.5N2 H4 nanobelts, which are synthesized by a simple hydrothermal method. As-synthesized precursor nanobelts are with 200 nm in width and several hundreds of micrometers in length. Annealed in N2 , they are transformed into ZnSe nanobelts with preserving their initial morphology. Following with a complete replacement of Zn(2+) by Ag(+), Ag2Se nanobelts with single crystalline are obtained via a cation-exchange reaction. Combined with the Langmuir-Blodgett assembly technique, regular films of ZnSe nanobelts can be achieved on transparent glass substrates and Si wafers with interdigital Au electrode arrays. Further, the optical and electrical evolutions are investigated from ZnSe nanobelts to Ag2 Se nanobelts. Finally, the resistive switching characteristic are carefully explored for Ag2Se nanobelts regularly arranged on interdigital Au microelectrodes. The results indicate that it is analogous to complementary resistive switching behaviors, which is different from that of traditional two terminal devices about previously reported Ag2Se. In order to clarify this phenomenon, a possible mechanism has been proposed and indirectly demonstrated through in situ SEM (scanning electron microscropy) observation.

Facet-dependent stripping behavior of Cu2O microcrystals toward lead ions: a rational design for the determination of lead ions.

Facet-dependent stripping behavior in the determination of Pb(II): Well-defined Cu2O microcrystals with different structures show facet-dependent electrochemical behaviors toward heavy metal ions. This provides an important insight into the understanding the efficiency of facet-dependent properties of microcrystals on electroanalytical performance for the rational design of electrochemical analytical techniques for efficient detection of heavy metal ions.

Electrochemical detection of arsenic(III) completely free from noble metal: Fe3O4 microspheres-room temperature ionic liquid composite showing better performance than gold.

In recent decades, electrochemical detection of arsenic(III) has been undergoing revolutionary developments with higher sensitivity and lower detection limit. Despite great success, electrochemical detection of As(III) still depends heavily on noble metals (predominantly Au) in a strong acid condition, thus increasing the cost and hampering the widespread application. Here, we report a disposable platform completely free from noble metals for electrochemical detection of As(III) in drinking water under nearly neutral condition by square wave anodic stripping voltammetry. By combining the high adsorptivity of Fe3O4 microspheres toward As(III) and the advantages of room temperature ionic liquid (RTIL), the Fe3O4-RTIL composite modified screen-printed carbon electrode (SPCE) showed even better electrochemical performance than commonly used noble metals. Several ionic liquids with different viscosities and surface tensions were found to have a different effect on the voltammetric behavior toward As(III). Under the optimized conditions, the Fe3O4-RTIL composites offered direct detection of As(III) within the desirable range (10 ppb) in drinking water as specified by the World Health Organization (WHO), with a detection limit (3σ method) of 8 × 10(-4) ppb. The obtained sensitivity was 4.91 µA ppb(-1), which is the highest as far as we know. In addition, a possible mechanism for As(III) preconcentration based on adsorption has been proposed and supported by designed experiments. Finally, this platform was successfully applied to analyzing a real sample collected from Inner Mongolia, China.

Electrochemical and density functional theory investigation on high selectivity and sensitivity of exfoliated nano-zirconium phosphate toward lead(II).

A new strategy on the understanding of selective and sensitive identification of Pb(II) using combined experimental and theoretical efforts is described. Amorphous phase formation of exfoliated nano-zirconium phosphate (ZrP) has been prepared via a hydrothermal process and subsequent intercalation reaction. Exfoliated ZrP was used as coating on the electrode surface, and it was found to be selective and sensitive for Pb(II) detection due to its selective adsorption ability. To better and scientifically understand the microscopic adsorption mechanism, density functional theory (DFT) calculations about the details of chemical interactions between heavy metal ions and exfoliated ZrP were carried out at an atomistic level. It is verified that the exfoliated ZrP shows the strongest adsorption capability toward Pb(II) among all heavy metal ions, thereby resulting in selective detection consequently. With our combined experimental and theoretical efforts, we are able to provide a new route to realize the improved selectivity in electrochemical sensing of toxic metal ions.

SnO2 tube-in-tube nanostructures: Cu@C nanocable templated synthesis and their mutual interferences between heavy metal ions revealed by stripping voltammetry.

SnO2 tube-in-tube nanostructures are synthesized using Cu@C nanocables as effective sacrificial templates. It is revealed by stripping voltammetry that SnO2 tube-in-tube nanostructures show excellent performances in the determination of heavy metal ions, which might be related to the extraordinary adsorbing capacities of the hollow structure to metal ions, i.e., metal ions could diffuse into the interior of tubular structure.

Enhancing selectivity in stripping voltammetry by different adsorption behaviors: the use of nanostructured Mg-Al-layered double hydroxides to detect Cd(II).

We report the use of nanostructured layered double hydroxides (LDHs) for the highly selective and sensitive detection of Cd(2+) using anodic stripping voltammetry (ASV). In particular, the modification of a glassy carbon electrode promotes the sensitivity and selectivity towards Cd(2+) in the presence of Pb(2+), Hg(2+), Cu(2+) and Zn(2+). The electrochemical characterization and anodic stripping voltammetric performance of Cd(2+) were evaluated using cyclic voltammetry (CV) and square wave anodic stripping voltammetry (SWASV) analysis. Operational parameters, including supporting electrolytes, pH value, deposition potential and deposition time were optimized. In addition, the selectivity, interference and stability were also investigated under the optimized conditions. The results showed that the fabricated electrode possessed good selectivity, stability and reproducibility. The proposed electrochemical sensing strategy is thus expected to open new opportunities to broaden the use of ASV in analysis for detecting heavy metal ions in the environment.