Effect of Reaction Temperature on the Microstructure and Properties of Magnesium Phosphate Chemical Conversion Coatings on Titanium.

Magnesium phosphate (MgP) has garnered growing interest in hard tissue replacement processes due to having similar biological characteristics to calcium phosphate (CaP). In this study, an MgP coating with the newberyite (MgHPO4·3H2O) was prepared on the surface of pure titanium (Ti) using the phosphate chemical conversion (PCC) method. The influence of reaction temperature on the phase composition, microstructure, and properties of coatings was systematically researched with the use of an X-ray diffractometer (XRD), a scanning electron microscope (SEM), a laser scanning confocal microscope (LSCM), a contact angle goniometer, and a tensile testing machine. The formation mechanism of MgP coating on Ti was also explored. In addition, the corrosion resistance of the coatings on Ti was researched by assessing the electrochemical behavior in 0.9% NaCl solution using an electrochemical workstation. The results showed that temperature did not obviously affect the phase composition of the MgP coatings, but affected the growth and nucleation of newberyite crystals. In addition, an increase in reaction temperature had a great impact on properties including surface roughness, thickness, bonding strength, and corrosion resistance. Higher reaction temperatures resulted in more continuous MgP, larger grain size, higher density, and better corrosion resistance.

Effect of Substrates Performance on the Microstructure and Properties of Phosphate Chemical Conversion Coatings on Metal Surfaces.

Phosphate chemical conversion (PCC) technology has attracted extensive attention for its ability to regulate the surface properties of biomedical metals. However, titanium (Ti)-based alloys exhibit inertia because of the native passive layer, whereas zinc (Zn)-based alloys show high activity in acidic PCC solutions. The substrate performance affects the chemical reaction in the phosphating solution, which further leads to diversity in coating properties. In this work, the zinc-phosphate (ZnP) coatings are prepared on Ti alloy (TA) and Zn alloy (ZA) substrates using the PCC method, respectively. The coatings prepared herein are detected by a scanning electron microscope (SEM), X-ray diffractometer (XRD), laser scanning confocal microscope (LSCM), universal testing machine, contact angle goniometer, and electrochemical workstation system. The results show that the substrate performance has little effect on the phase composition but can significantly affect the crystal microstructure, thickness, and bonding strength of the coatings. In addition, the ZnP coatings improve the surface roughness of the substrates and show good hydrophilicity and electrochemical corrosion resistance. The formation mechanism of the ZnP coating is revealed using potential-time curves, indicating that the metal-solution interfacial reaction plays a dominant role in the deposition process.

Engineering titania nanostructure to tune and improve its photocatalytic activity.

Photocatalytic pathways could prove crucial to the sustainable production of fuels and chemicals required for a carbon-neutral society. Electron-hole recombination is a critical problem that has, so far, limited the efficiency of the most promising photocatalytic materials. Here, we show the efficacy of anisotropy in improving charge separation and thereby boosting the activity of a titania (TiO2) photocatalytic system. Specifically, we show that H2 production in uniform, one-dimensional brookite titania nanorods is highly enhanced by engineering their length. By using complimentary characterization techniques to separately probe excited electrons and holes, we link the high observed reaction rates to the anisotropic structure, which favors efficient carrier utilization. Quantum yield values for hydrogen production from ethanol, glycerol, and glucose as high as 65%, 35%, and 6%, respectively, demonstrate the promise and generality of this approach for improving the photoactivity of semiconducting nanostructures for a wide range of reacting systems.

Preparation of well-distributed titania nanopillar arrays on Ti6Al4V surface by induction heating for enhancing osteogenic differentiation of stem cells.

Great effort has recently been devoted to the preparation of nanoscale surfaces on titanium-based implants to achieve clinically fast osteoinduction and osseointegration, which relies on the unique characteristics of the nanostructure. In this work, we used induction heating treatment (IHT) as a rapid oxidation method to fabricate a porous nanoscale oxide layer on the Ti6Al4V surface for better medical application. Well-distributed vertical nanopillars were yielded by IHT for 20-35 s on the alloy surface. The composition of the oxides contained rutile/anatase TiO2 and a small amount of Al2O3 between the TiO2 grain boundaries (GBs). This technology resulted in a reduction and subsequent increase of surface roughness of 26-32 nm when upregulating the heating time, followed by the successive enhancement of the thickness, wettability and adhesion strength of the oxidation layer to the matrix. The surface hardness also distinctly rose to 554 HV in the IHT-35 s group compared with the 350 HV of bare Ti6Al4V. The massive small-angle GBs in the bare alloy promoted the formation of nanosized oxide crystallites. The grain refinement and deformation texture reduction further improved the mechanical properties of the matrix after IHT. Moreover, in vitro experiments on a mesenchymal stem cell (BMSC) culture derived from human bone marrow for 1-7 days indicated that the nanoscale layers did not cause cytotoxicity, and facilitated cell differentiation in osteoblasts by enhancing the gene and osteogenesis-related protein expressions after 1-3 weeks of culturing. The increase of the IHT time slightly advanced the BMSC proliferation and differentiation, especially during long-term culture. Our findings provide strong evidence that IHT oxidation technology is a novel nanosurface modification technology, which is potentially promising for further clinical development.

The Formation Process and Mechanism of the 3D Porous Network on the Sulfonated PEEK Surface.

A three-dimensional (3D) porous network can be prepared on the PEEK surface by sulfonation with enhanced osseointegration and antibacterial properties. However, few studies have been conducted on the formation mechanism of a 3D porous network. In this work, the surface and cross-sectional morphologies, chemical compositions, functional groups, surface wettability, and crystalline states of sulfonated PEEK were investigated at different sulfonation times and coagulant concentrations. The results show that the number of nodular structures and broken fibers on the sulfonated PEEK surface as well as the size of macrovoids in the cross sections increase with increasing sulfonation times when water is used as a coagulant. In contrast, dilute sulfuric acid as a coagulant can inhibit the formation of surface porous structures and macrovoids in the cross sections. Moreover, all of the sulfonated PEEK samples have the same chemical compositions but exhibit better hydrophilicity as the number of microsized pores decreases. It is proposed that non-solvent-induced phase separation (NIPS) occurs during the sulfonation process, and the formation mechanism of surface and cross-sectional morphologies is discussed. Furthermore, it is assumed that the air is trapped in the microsized pores, leaving the surface of the 3D porous network in the Cassie-wetting state. All of these preliminary results throw light on the nature of the sulfonation process and may guide further modification of the structures of sulfonated PEEK.

Construction of Magnesium Phosphate Chemical Conversion Coatings with Different Microstructures on Titanium to Enhance Osteogenesis and Angiogenesis.

Titanium (Ti) and its alloys are widely used as hard tissue substitutes in dentistry and orthopedics, but their low bioactivity leads to undesirable osseointegration defects in the early osteogenic phase. Surface modification is an important approach to overcome these problems. In the present study, novel magnesium phosphate (MgP) coatings with controllable structures were fabricated on the surface of Ti using the phosphate chemical conversion (PCC) method. The effects of the microstructure on the physicochemical and biological properties of the coatings on Ti were researched. The results indicated that accelerators in PCC solution were important factors affecting the microstructure and properties of the MgP coatings. In addition, the coated Ti exhibited excellent hydrophilicity, high bonding strength, and good corrosion resistance. Moreover, the biological results showed that the MgP coatings could improve the spread, proliferation, and osteogenic differentiation of mouse osteoblast cells (MC3T3-E1) and vascular differentiation of human umbilical vein endothelial cells (HUVECs), indicating that the coated Ti samples had a great effect on promoting osteogenesis and angiogenesis. Overall, this study provided a new research idea for the surface modification of conventional Ti to enhance osteogenesis and angiogenesis in different bone types for potential biomedical applications.

Effects of Heating Rates on Microstructural Evolution of Hot Extruded 7075 Aluminum Alloy in the Semi-Solid State and Thixotropic Deformation Behavior.

The non-dendritic microstructure plays a crucial role in determining the rheological properties of semi-solid alloys, which are of the utmost importance for the successful industrial application of the thixoforging process. To further understand the impact of the reheating process on the evolution of microstructure and thixotropic deformation behavior in the semi-solid state, a hot extruded and T6 treated 7075 aluminum alloy was reheated to the selected temperature ranges using varying heating rates. Subsequently, thixo-compression tests were performed. The study found that during reheating and isothermal holding, the elongated microstructure of the as-supplied alloy can transform into equiaxed or spherical grains. The presence of recrystallized grains was found to be closely linked to the penetration of the liquid phase into the recrystallized grain boundaries. Furthermore, it was observed that higher heating rates resulted in smaller grain sizes. The thixotropic flow behavior of the alloy with various microstructures was analyzed using the true stress-strain curves obtained by thixo-compression experiments, which exhibited three stages: a rapid increase in true stress to a peak value, followed by a decrease in true stress and a steady stress until the end of compression. The stress fluctuated with strain during the formation of the slurry at a strain rate of 10 s-1, indicating the significant role of strain rate in material flow during semisolid formation.

Targeted multi-platform metabolome analysis and enzyme activity analysis of kiwifruit during postharvest ripening.

Kiwifruit is a climacteric fruit, in which the accumulation of flavor substances mainly occurs at the postharvest ripening stage. However, the dynamic changes in metabolite composition remain poorly understood. Here, targeted multi-platform metabolome analysis based on GC-MS and UPLC-MS/MS and enzyme activity analysis were performed at different postharvest ripening stages of kiwifruit. A total of 12 soluble sugars and 31 organic acids were identified. The main soluble sugars are sucrose, glucose and fructose, which exhibited similar variation tendencies along with the extension of ripening. The main organic acids are citric acid, quinic acid and malic acid, which showed different variation patterns. A total of 48 energy metabolites were identified, which were classified into two groups based on the content variation. The content of substances related to the respiratory metabolic pathway decreased gradually along with postharvest ripening, and there was obvious accumulation of downstream products such as amino acids at the late ripening stage. A total of 35 endogenous hormones were identified, among which seven cytokinins were highly accumulated at the later stage of softening. We further investigated the dynamic changes in the activities of 28 ripening-related enzymes. As a result, the activities of 13 enzymes were highly correlated with changes in starch, total pectin, and soluble sugars, and those of seven enzymes were closely associated with the change in firmness. In conclusion, this study comprehensively describes the dynamic changes in soluble sugars, organic acids, hormones, energy substances, and ripening-related enzyme activities during kiwifruit postharvest ripening, and provides a theoretical basis for the postharvest quality improvement of kiwifruit.

A Comparative Study on Microstructure, Segregation, and Mechanical Properties of Al-Si-Mg Alloy Parts Processed by GISS-HPDC and SEED-HPDC.

There are multiple routes to prepare semi-solid slurries with a globular microstructure for semi-solid forming. The variations in the microstructure of semi-solid slurries prepared using different routes may lead to significant differences in the flow behavior and mechanical properties of rheo-diecasting parts. Therefore, it is crucial to have a comprehensive understanding of the microstructure evolution associated with different slurry preparation routes and their resulting effects. In this study, the gas-induced semi-solid process (GISS) and the swirl enthalpy equilibrium device (SEED) routes were employed to prepare semi-solid Al-Si-Mg slurries for their simplicity and productivity in potential industrial applications. The prepared slurries were then injected into the shoot sleeves of a high-pressure die casting (HPDC) machine to produce tensile test bars. Subsequently, the bars underwent T6 treatment to enhance their mechanical properties. The microstructure, segregation, and mechanical properties of the samples were investigated and compared with those of conventional HPDC. The results indicated that the GISS and SEED can produce semi-solid slurries containing a spherical α-Al primary phase, as opposed to the dendritic structure commonly found in conventional castings. The liquid fraction had a significant effect on the flow behavior, resulting in variations in liquid segregation and mechanical properties. It was observed that a higher solid fraction (>75%) had a suppressing effect on surface liquid segregation. In addition, the tendency for liquid segregation gradually increased along the filling direction due to the special flow behavior of the semi-solid slurry with a low solid fraction. Furthermore, under the same die-casting process parameters, the conventional HPDC samples exhibit higher yield stress (139 ± 3 MPa) compared to SEED-HPDC and GISS-HPDC samples, which may be attributed to the small grain size and the distribution of eutectic phases. After undergoing the T6 treatment, both SEED-HPDC and GISS-HPDC samples showed a significant improvement in yield and tensile strength. These improvements are a result of solution and precipitation strengthening effects as well as the spheroidization of the eutectic Si phase. Moreover, the heat-treated SEED-HPDC samples demonstrate higher ultimate strength (336 ± 5 MPa) and elongation (13.7 ± 0.3%) in comparison to the GISS-HPDC samples (307 ± 4 MPa, 8.8 ± 0.2%) after heat treatment, mainly due to their low porosity density. These findings suggest that both GISS-HPDC and SEED-HPDC processes can be utilized to produce parts with favorable mechanical properties by implementing appropriate heat treatments. However, further investigation is required to control the porosities of GISS-HPDC samples during heat treatment.

Calcium-Zinc Phosphate Chemical Conversion Coating Facilitates the Osteointegration of Biodegradable Zinc Alloy Implants by Orchestrating Macrophage Phenotype.

Zinc (Zn) alloys provide a new generation for orthopedic applications due to their essential physiological effects and promising degradation properties. However, excessive release of Zn ions (Zn2+ ) during degradation and the severe inflammatory microenvironment are not conducive to osseointegration, which is determined by the characteristics of the implant surface. Therefore, it is essential to modulate the release rate of Zn alloys by surface modification technology and endow them with anti-inflammatory and osteogenic effects. In this study, two kinds of phosphate chemical conversion (PCC) coatings with different compositions and morphological structures are prepared, namely Zn-P (with disk-like crystals) and Ca-Zn-P (with lamellar crystals). Although all the PCC-coated Zn implants have low cytotoxicity, Ca-Zn-P show better osteoimmunomodulation effects in several aspects: the induction of the M2-phenotype macrophage polarization and thus promotion of osteogenesis in vitro; the regulation of the bone immune microenvironment which is conducive to tissue regeneration and osseointegration in vivo; and the release of ions (through PI3K/AKT and Wnt signaling pathways) and the morphological structures (through RhoGTPase signaling pathways) act as possible mechanisms of M2 polarization. The Ca-Zn-P coating can be considered to provide new insights into bone immunomodulation and osseointegration.

Study on Mandrel Forging and Necking Process of a Hollow Shaft with an Inner Stepped Hole.

An advanced process of mandrel forging and necking (MFN) was proposed for a hollow shaft with an inner stepped hole. The conventional mandrel forging process with an equal-diameter mandrel was used to form the outer stepped preform, and then the preform was formed into the hollow shaft with an inner stepped hole using the MFN process. A numerical simulation model was established to study the effect of the pressing reduction and the rotation angle on the MFN process. A preforming design method based on the isometric radius difference was given according to the principle of the equal volume, and the parameter relationships between the outer and inner stepped shapes were clarified. The experimental deformation laws of the MFN process were consistent with those obtained by the simulation. The MFN process and its preforming design method provide a new free forging approach for large hollow forgings with inner stepped holes.

Zinc-Doping Induces Evolution of Biocompatible Strontium-Calcium-Phosphate Conversion Coating on Titanium to Improve Antibacterial Property.

Implant-associated infections (IAI) remains a common and devastating complication in orthopedic surgery. To reduce the incidence of IAI, implants with intrinsic antibacterial activity have been proposed. The surface functionalization and structure optimization of metallic implants can be achieved by surface modification using the phosphate chemical conversion (PCC) technique. Zinc (Zn) has strong antibacterial behavior toward a broad-spectrum of bacteria. Herein, Zn was incorporated into strontium-calcium-phosphate (SrCaP) coatings on titanium (Ti) via PCC method, and the influence of its doping amount on the phase, microstructure, antibacterial activity, and biocompatibility of the composite coating was researched. The results indicated that traces of Zn doping produced grain refinement of SrCaP coating with no significant effect on its phase and surface properties, while a higher Zn content induced its phase and microstructure transformed into zinc-strontium-phosphate (SrZn2(PO4)2). SrCaP-Zn1 and SrCaP-Zn4 represented trace and high content Zn-doped coatings, respectively, which exhibited a similar bacterial attachment for a short time but showed inhibition of biofilm formation after continuous incubation up to 24 h. The killing rates of SrCaP-Zn1 coating for Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) reached 61.25% and 55.38%, respectively. While that data increased to 83.01% and 71.28% on SrCaP-Zn4 coating due to the more-releasing Zn2+. Furthermore, in vitro culture of MC3T3-E1 cells proved that the Zn-doped coatings also possessed excellent biocompatibility. This study provides a new perception for the phase and microstructural optimization of phosphate coatings on implant surfaces, as well as fabricating promising coatings with excellent biocompatibility and antimicrobial properties against IAI.

The Impact of Human Pressure and Climate Change on the Habitat Availability and Protection of Cypripedium (Orchidaceae) in Northeast China.

Human pressure on the environment and climate change are two important factors contributing to species decline and overall loss of biodiversity. Orchids may be particularly vulnerable to human-induced losses of habitat and the pervasive impact of global climate change. In this study, we simulated the extent of the suitable habitat of three species of the terrestrial orchid genus Cypripedium in northeast China and assessed the impact of human pressure and climate change on the future distribution of these species. Cypripedium represents a genus of long-lived terrestrial orchids that contains several species with great ornamental value. Severe habitat destruction and overcollection have led to major population declines in recent decades. Our results showed that at present the most suitable habitats of the three species can be found in Da Xing'an Ling, Xiao Xing'an Ling and in the Changbai Mountains. Human activity was predicted to have the largest impact on species distributions in the Changbai Mountains. In addition, climate change was predicted to lead to a shift in distribution towards higher elevations and to an increased fragmentation of suitable habitats of the three investigated Cypripedium species in the study area. These results will be valuable for decision makers to identify areas that are likely to maintain viable Cypripedium populations in the future and to develop conservation strategies to protect the remaining populations of these enigmatic orchid species.

Interleukin-4 assisted calcium-strontium-zinc-phosphate coating induces controllable macrophage polarization and promotes osseointegration on titanium implant.

Titanium (Ti) and its alloys are believed to be promising scaffold materials for dental and orthopedic implantation due to their ideal mechanical properties and biocompatibility. However, the host immune response always causes implant failures in the clinic. Surface modification of the Ti scaffold is an important factor in this process and has been widely studied to regulate the host immune response and to further promote bone regeneration. In this study, a calcium-strontium-zinc-phosphate (CSZP) coating was fabricated on a Ti implant surface by phosphate chemical conversion (PCC) technique, which modified the surface topography and element constituents. Here, we envisioned an accurate immunomodulation strategy via delivery of interleukin (IL)-4 to promote CSZP-mediated bone regeneration. IL-4 (0 and 40 ng/mL) was used to regulate immune response of macrophages. The mechanical properties, biocompatibility, osteogenesis, and anti-inflammatory properties were evaluated. The results showed that the CSZP coating exhibited a significant enhancement in surface roughness and hydrophilicity, but no obvious changes in proliferation or apoptosis of bone marrow mesenchymal stem cells (BMMSCs) and macrophages. In vitro, the mRNA and protein expression of osteogenic related factors in BMMSCs cultured on a CSZP coating, such as ALP and OCN, were significantly higher than those on bare Ti. In vivo, there was no enhanced bone formation but increased macrophage type 1 (M1) polarization on the CSZP coating. IL-4 could induce M2 polarization and promote osteogenesis of BMMSCs on CSZP in vivo and in vitro. In conclusion, the CSZP coating is an effective scaffold for BMMSCs osteogenesis, and IL-4 presents the additional advantage of modulating the immune response for bone regeneration on the CSZP coating in vivo.

Efficacy of concentrated growth factors combined with mineralized collagen on quality of life and bone reconstruction of guided bone regeneration.

To evaluate the clinical efficacy of concentrated growth factors (CGFs) combined with mineralized collagen (MC) in guided bone regeneration (GBR). A retrospective study involving 29 patients treated with GBR technique, which was performed either CGF and MC complexes or MC alone. Implants were inserted simultaneously and cone-beam computed tomography was taken immediately, at 3 and 6 months postoperation. Questionnaires were completed by all patients so as to evaluate the main symptoms and daily activities during the first week after surgery. The outcomes of the two groups were statistically compared. All implants healed uneventfully. Patients in both groups suffered from different levels of discomfort for the reason of swelling, pain and chewing impairment on 1-2 days. Meanwhile, swelling of the Trial group was weaker than the Control group. When compared with the Control group, pain levels in Trial group were more rapidly reduced and patients took fewer analgesics from Day 3. Furthermore, the reconstitution mean value of the graft was thicker at 3 and 6 months in Trial group. CGFs complex with MC were beneficial to relieve the clinical symptoms, promote the peri-implant bone regeneration and shorten the healing time.

Investigation of nature of starting materials on the construction of hydroxyapatite 1D/3D morphologies.

With the increasing requirement of bone repair materials, hydroxyapatite (HA) has been paid widely attention to investigation because of its good bioactivity and osteoconductivity. The structure of HA is a vital factor to expand its application in the field of hard tissue therapy. Thus, many strategies have been utilized in fabricating one-dimensional (1D) and three-dimensional (3D) nanostructured HA. In this paper, we successful synthesize HA with 1D nanofibers and 3D nanostructured microspheres using stearic acid as a template and different phosphates as phosphorus sources under the same synthetic system. The morphology of HA changes from nanofibers with high flexibility to nanostructured microspheres with good sphericity under the synergistic effect of stearic acid and various phosphates. The HA nanofibers and microspheres are promising for applications in biomedical fields. Base on characterization results, the formation mechanisms of HA nanofibers and HA microspheres self-assembled by nanorods are proposed. Furthermore, the HA morphology transition from nanofibers to nanostructured microspheres may be attributed to the formation of polyphosphate-induced water-in-oil microemulsion system in the synthesis process. The finding may provide a new direction to control HA morphology from 1D nanofibers to 3D microspheres based on previous strategies.

Revealing nanoscale mineralization pathways of hydroxyapatite using in situ liquid cell transmission electron microscopy.

To treat impairments in hard tissues or overcome pathological calcification in soft tissues, a detailed understanding of mineralization pathways of calcium phosphate materials is needed. Here, we report a detailed mechanistic study of hydroxyapatite (HA) mineralization pathways in an artificial saliva solution via in situ liquid cell transmission electron microscopy (TEM). It is found that the mineralization of HA starts by forming ion-rich and ion-poor solutions in the saliva solution, followed by coexistence of the classical and nonclassical nucleation processes. For the nonclassical path, amorphous calcium phosphate (ACP) functions as the substrate for HA nucleation on the ACP surface, while the classical path features direct HA nucleation from the solution. The growth of HA crystals on the surface of ACP is accompanied by the ACP dissolution process. The discoveries reported in this work are important to understand the physiological and pathological formation of HA minerals, as well as to engineer the biomineralization process for bone healing and hard tissue repairs.

Novel PMMA bone cement nanocomposites containing magnesium phosphate nanosheets and hydroxyapatite nanofibers.

Lack of bioactivity and monomer toxicity are limiting factors of polymethyl methacrylate (PMMA) bone cement in orthopedic applications. Herein, we address these shortcomings by proposing two-dimensional magnesium phosphate (MgP) nanosheets and hydroxyapatite (HA) nanofibers as novel fillers in PMMA bone cement nanocomposites. Two-dimensional MgP nanosheets and one-dimensional HA nanofibers were synthesized by tuning the crystallization of the sodium-magnesium-phosphate ternary system and hydrothermal homogeneous precipitation, respectively. We show that MgP nanosheets exhibit antibacterial properties against Escherichia coli (E. coli). In addition, HA nanofibers with high level of bioactivity are the proper choice to induce cell viability in the nanocomposite. Results indicate that the combination of both fillers can act as deformation locks enhancing the compressive strength of the nanocomposites. The synthesized nanocomposite possesses excellent bioactivity, mechanical properties, and cytocompatibility potentially opening new paradigm in the design of next generation bone cement composites.

Interfacial tissue engineering of heart regenerative medicine based on soft cell-porous scaffolds.

Myocardial infarction (MI), occurs when the coronary artery is occluded resulting in the hypoxia of areas in heart tissue, is increasing in recent years because of the population ageing and lifestyle changes. Currently, there is no ideal therapeutic scheme because of the limitation of MI therapeutic strategies due to the lack of regenerative ability of the heart cells in adult humans. Recent advances in tissue engineering and regenerative medicine brings hope to the MI therapy and current studies are focusing on restoring the function and structure of damaged tissue by delivering exogenous cells or stimulating endogenous heart cells. However, attempts to directly inject stem cells or cardiomyocytes to the infract zone often lead to rapid cell death and abundant cell loss. To address this challenge, various soft repair cells and porous scaffold materials have been integrated to improve cell retention and engraftment and preventing left ventricle (LV) dilatation. In this article, we will review the current method for heart regeneration based on soft cell-porous scaffold interfacial tissue engineering including common stem cell types, biomaterials, and cardiac patch and will discuss potential future directions in this area.

In-situ preparation of scholzite conversion coatings on titanium and Ti-6Al-4V for biomedical applications.

A scholzite (CaZn2(PO4)2·2H2O) coating was prepared in situ on commercially pure titanium (cpTi) and Ti-6Al-4V (Ti64) substrates using the chemical conversion technology, and its phase composition and microstructure, as well as mechanical, chemical and biological properties were investigated to explore potential applications as a bioactive coating on bone implants. It is indicated that the coating consists mainly of monoclinic scholzite crystals with nano-thick laminar morphology. The crystals on cpTi aggregate to flower-like particles with the diameter of 5-10µm, while form a network structure homogeneously on Ti64. The scratch test shows that the interfacial bonding strength between the coatings and substrates is higher than 40N. Electrochemical measurements indicate that the corrosion behavior of the coatings is not inferior compared with that of oxide film on substrates. MG63 osteoblast-like cells show good adherence and significantly proliferation and differentiation characteristics on the scholzite coated cpTi and Ti64 (p<0.05) in in-vitro cell tests, demonstrating the cytocompatibility of Ti is significantly improved by the scholzite coating. It is suggested that the scholzite coating might be a promising option in hard tissue replacements for early osteogenesis.