RESUMEN
Multifunctional optical fiber-based neural interfaces have attracted significant attention for neural stimulation, recording, and photopharmacology towards understanding the central nervous system. In this work, we demonstrate the fabrication, optoelectrical characterization, and mechanical analysis of four types of microstructured polymer optical fiber neural probes using different soft thermoplastic polymers. The developed devices have integrated metallic elements for electrophysiology and microfluidic channels for localized drug delivery, and can be used for optogenetics in the visible spectrum at wavelengths spanning from 450â nm up to 800â nm. Their impedance, measured by electrochemical impedance spectroscopy, was found to be as low as 21 kΩ and 4.7 kΩ at 1kHz when indium and tungsten wires are used as the integrated electrodes, respectively. Uniform on-demand drug delivery can be achieved by the microfluidic channels with a measured delivery rate from 10 up to 1000 nL/min. In addition, we identified the buckling failure threshold (defined as the conditions for successful implantation) as well as the bending stiffness of the fabricated fibers. Using finite element analysis, we calculated the main critical mechanical properties of the developed probes to avoid buckling during implantation and maintain high flexibility of the probe within the tissue. Our results aim to demonstrate the impact of design, fabrication, and characteristics of the materials on the development of polymer fibers as next-generation implants and neural interfaces.
RESUMEN
Variation of the brain temperature is strongly affected by blood flow, oxygen supply, and neural cell metabolism. Localized monitoring of the brain temperature is one of the most effective ways to correlate brain functions and diseases such as stroke, epilepsy, and mood disorders. While polymer optical fibers (POFs) are considered ideal candidates for temperature sensing in the brain, they have never been used so far in vivo. Here, we developed for the first, to the best of our knowledge, time an implantable probe based on a microstructured polymer optical fiber Bragg grating (FBG) sensor for intracranial brain temperature mapping. The temperature at different depths of the brain (starting from the cerebral cortex) and the correlation between the brain and body core temperature of a rat were recorded with a sensitivity of 33 pm/°C and accuracy <0.2°C. Our in vivo experimental results suggest that the proposed device can achieve real-time and high-resolution local temperature measurement in the brain, as well as being integrated with existing neural interfaces.
Asunto(s)
Fibras Ópticas , Termografía , Animales , Ratas , Temperatura , Polímeros , EncéfaloRESUMEN
Understanding the impact of the cladding tube structure on the overall guiding performance is crucial for designing a single-mode, wide-band, and ultra low-loss nested hollow-core anti-resonant fiber (HC-ARF). Here we thoroughly investigate on how the propagation loss is affected by the nested elements when their geometry is realistic (i.e., non-ideal). Interestingly, it was found that the size, rather than the shape, of the nested elements has a dominant role in the final loss performance of the regular nested HC-ARFs. We identify a unique 'V-shape' pattern for suppression of higher-order modes loss by optimizing free design parameters of the HC-ARF. We find that a 5-tube nested HC-ARF has wider transmission window and better single-mode operation than a 6-tube HC-ARF. We show that the propagation loss can be significantly improved by using anisotropic nested anti-resonant tubes elongated in the radial direction. Our simulations indicate that with this novel fiber design, a propagation loss as low as 0.11 dB/km at 1.55 µm can be achieved. Our results provide design insight toward fully exploiting a single-mode, wide-band, and ultra low-loss HC-ARF. In addition, the extraordinary optical properties of the proposed fiber can be beneficial for several applications such as future optical communication system, high energy light transport, extreme non-nonlinear optics and beyond.
RESUMEN
A hollow-core anti-resonant fiber (HC-ARF) design based on hybrid silica/silicon cladding is proposed for single-polarization, single-mode and high birefringence. We show that by adding silicon layers in a semi-nested HC-ARF, one of the polarization states can be strongly suppressed while simultaneously maintaining low propagation loss for other polarization states, single-mode and high birefiringence. The optimized HC-ARF design exhibits propagation loss, high birefringence, and polarization-extinction ratio of 0.05 dB/m, 0.5 × 10-4, >300 respectively for y-polarization while the loss of x-polarization is >5 dB/m at 1064 nm. The fiber also has low bend-loss and thus can be coiled to a small bend radii of 5 cm having ≈0.06 dB/m bend loss.
RESUMEN
In this Letter, we present a high-pulse energy (>10µJ) Raman laser at 1946 nm wavelength directly pumped with a 1533 nm custom-made fiber laser. The Raman laser is based on stimulated Raman scattering (SRS) in an 8 m carbon dioxide (CO2)-filled nested anti-resonant hollow-core fiber. The low-energy phonon emission combined with the inherent SRS process along the low-loss fiber allows the generation of high-pulse energy up to 15.4 µJ at atmospheric CO2 pressure. The Raman laser exhibits good long-term stability and low relative intensity noise of less than 4%. We also investigate the pressure-dependent overlap of the Raman laser line with the absorption band of CO2 at the 2 µm spectral range. Our results constitute a novel, to the best of our knowledge, and promising technology towards high-energy 2 µm lasers.
RESUMEN
A hybrid optical fiber comprising metal electrodes, high performance polymers, and a highly nonlinear glass core is presented in this work as a novel, to the best of our knowledge, platform for mid-infrared nonlinear devices. The fiber allows for electrical tuning of the temperature by joule heating using a set of embedded tungsten wires. Unlike temperature tuning by an external heater, this results in a strong modulation, which introduces alternating signs of its dispersion. Enhanced spectral broadening through supercontinuum generation in the mid-infrared due to this modulation is investigated numerically.
RESUMEN
In this work, we present a high-pulse-energy multi-wavelength Raman laser spanning from 1.53 µm up to 2.4 µm by employing the cascaded rotational stimulated Raman scattering effect in a 5 m hydrogen (H2)-filled nested anti-resonant fiber, pumped by a linearly polarized Er/Yb fiber laser with a peak power of â¼13kW and pulse duration of â¼7ns in the C-band. The developed Raman laser has distinct lines at 1683 nm, 1868 nm, 2100 nm, and 2400 nm, with pulse energies as high as 18.25 µJ, 14.4 µJ, 14.1 µJ, and 8.2 µJ, respectively. We demonstrate how the energy in the Raman lines can be controlled by tuning the H2 pressure from 1 bar to 20 bar.
RESUMEN
In this Letter, we demonstrate a high pulse energy and linearly polarized mid-infrared Raman fiber laser targeting the strongest absorption line of ${\rm CO}_2$CO2 at $\sim{4.2}\;\unicode {x00B5} {\rm m}$â¼4.2µm. This laser was generated from a hydrogen (${\rm H}_2$H2)-filled antiresonant hollow-core fiber, pumped by a custom-made 1532.8 nm Er-doped fiber laser delivering 6.9 ns pulses and 11.6 kW peak power. A quantum efficiency as high as 74% was achieved, to yield 17.6 µJ pulse energy at 4.22 µm. Less than 20 bar ${\rm H}_2$H2 pressure was required to maximize the pulse energy since the transient Raman regime was efficiently suppressed by the long pump pulses.
RESUMEN
In this paper, we numerically investigate various hollow-core anti-resonant (HC-AR) fibers towards low propagation and bend loss with effectively single-mode operation in the telecommunications window. We demonstrate how the propagation loss and higher-order mode modal contents are strongly influenced by the geometrical structure and the number of the anti-resonant cladding tubes. We found that 5-tube nested HC-AR fiber has a wider anti-resonant band, lower loss, and larger higher-order mode extinction ratio than designs with 6 or more anti-resonant tubes. A loss ratio between the higher-order modes and fundamental mode, as high as 12,000, is obtained in a 5-tube nested HC-AR fiber. To the best of our knowledge, this is the largest higher-order mode extinction ratio demonstrated in a hollow-core fiber at 1.55 µm. In addition, we propose a modified 5-tube nested HC-AR fiber, with propagation loss below 1 dB/km from 1330 to 1660 nm. This fiber also has a small bend loss of ~15 dB/km for a bend radius of 1 cm.
RESUMEN
Broadband supercontinuum generation is numerically investigated in a Xe-filled nested hollow-core antiresonant (HC-AR) fiber pumped at 3 µm with pulses of 100 fs duration and 15 µJ energy. For a 25 cm long fiber, under 7 bar pressure, the supercontinuum spectrum spans multiple octaves from 400 nm to 5000 nm. Furthermore, the influence of bending on ultrafast nonlinear pulse propagation dynamics is investigated for two types of HC-AR fibers (nested and non-nested capillaries). Our results predict similar nonlinear dynamics for both fiber types and a significant reduction of the spectral broadening under tight bending conditions.
RESUMEN
In this work, we numerically investigate an experimentally feasible design of a tapered Ne-filled hollow-core anti-resonant fiber and we report multi-stage generation of dispersive waves (DWs) in the range 90-120 nm, well into the extreme ultraviolet (UV) region. The simulations assume a 800 nm pump pulse with 30 fs 10 µJ pulse energy, launched into a 9 bar Ne-filled fiber with a 34 µm initial core diameter that is then tapered to a 10 µm core diameter. The simulations were performed using a new model that provides a realistic description of both loss and dispersion of the resonant and anti-resonant spectral bands of the fiber, and also importantly includes the material loss of silica in the UV. We show that by first generating solitons that emit DWs in the far-UV region in the pre-taper section, optimization of the following taper structure can allow re-collision with the solitons and further up-conversion of the far-UV DWs to the extreme-UV with energies up to 190 nJ in the 90-120 nm range. This process provides a new way to generate light in the extreme-UV spectral range using relatively low gas pressure.
RESUMEN
The trade-off between the spectral bandwidth and average output power from chalcogenide fiber-based mid-infrared supercontinuum sources is one of the major challenges towards practical application of the technology. In this paper we address this challenge through tapering of large-mode-area chalcogenide photonic crystal fibers. Compared to previously reported step-index fiber tapers the photonic crystal fiber structure ensures single-mode propagation, which improves the beam quality and reduces losses in the taper due to higher-order mode stripping. By pumping the tapered fibers at 4 µm using a MHz optical parametric generation source, and choosing an appropriate length of the untapered fiber segments, the output could be tailored for either the broadest bandwidth from 1 to 11.5 µm with 35.4 mW average output power, or the highest output power of 57.3 mW covering a spectrum from 1 to 8 µm.
RESUMEN
We investigate numerically soliton-plasma interaction in a noble-gas-filled silica hollow-core anti-resonant fiber pumped in the mid-IR at 3.0 µm. We observe multiple soliton self-compression stages due to distinct stages where either the self-focusing or the self-defocusing nonlinearity dominates. Specifically, the parameters may be tuned so the competing plasma self-defocusing nonlinearity only dominates over the Kerr self-focusing nonlinearity around the soliton self-compression stage, where the increasing peak intensity on the leading pulse edge initiates a competing self-defocusing plasma nonlinearity acting nonlocally on the trailing edge, effectively preventing soliton formation there. As the plasma switches off after the self-compression stage, self-focusing dominates again, initiating another soliton self-compression stage in the trailing edge. This process is accompanied by supercontinuum generation spanning 1-4 µm. We find that the spectral coherence drops as the secondary compression stage is initiated.
RESUMEN
This publisher's note corrects Eq. (1) of Opt. Lett.42, 2232 (2017)OPLEDP0146-959210.1364/OL.42.002232.
RESUMEN
In the absence of suitable deposition processes, the fabrication of graded-index chalcogenide waveguides or fibers remains an outstanding challenge. Here, by exploiting the strong thermo-optic effect present in chalcogenide glasses, we experimentally demonstrate non-permanent optically-induced waveguides in bulk As2Se3 rods using a 1.55 µm wavelength laser. This single-step process can be used not only to self-trap the writing beam, but also to guide another optical beam at a different wavelength in the opto-thermally inscribed waveguide channel. These results could pave the way towards harnessing nonlinear effects in graded-index chalcogenide guided settings.
RESUMEN
In this Letter, we report for the first time, to the best of our knowledge, the fabrication and characterization of a Zeonex/PMMA microstructured polymer optical fiber (mPOF) Bragg grating sensor for simultaneous monitoring of relative humidity (RH) and temperature. The sensing element (probe) is based on two separate in-line fiber Bragg gratings (FBGs) inscribed in the fabricated mPOF. A root mean square deviation of 0.8% RH and 0.6°C in the range of 10%-90% RH and 20°C-80°C was found. The developed mPOFBG sensor constitutes an efficient route toward low-cost, easy-to-fabricate and compact multi-parameter sensing solutions.
RESUMEN
Environmentally robust chemical sensors for monitoring industrial processes or infrastructures are lately becoming important devices in industry. Low complexity and wireless enabled characteristics can offer the required flexibility for sensor deployment in adaptable sensing networks for continuous monitoring and management of industrial assets. Here are presented the design, development and operation of a class of low cost photonic sensors for monitoring the ageing process and the operational characteristics of coolant fluids used in an industrial heavy machinery infrastructure. The chemical, physical and spectroscopic characteristics of specific industrial-grade coolant fluids were analyzed along their entire life cycle range, and proper parameters for their efficient monitoring were identified. Based on multimode polymer or silica optical fibers, wide range (3-11) pH sensors were developed by employing sol-gel derived pH sensitive coatings. The performances of the developed sensors were characterized and compared, towards their coolants' ageing monitoring capability, proving their efficiency in such a demanding application scenario and harsh industrial environment. The operating characteristics of this type of sensors allowed their integration in an autonomous wireless sensing node, thus enabling the future use of the demonstrated platform in wireless sensor networks for a variety of industrial and environmental monitoring applications.
RESUMEN
The effect of humidity on annealing of poly (methyl methacrylate) (PMMA) based microstructured polymer optical fiber Bragg gratings (mPOFBGs) and the resulting humidity responsivity are investigated. Typically annealing of PMMA POFs is done in an oven without humidity control around 80°C and therefore at low humidity. We demonstrate that annealing at high humidity and high temperature improves the performances of mPOFBGs in terms of stability and sensitivity to humidity. PMMA POFBGs that are not annealed or annealed at low humidity level will have a low and highly temperature dependent sensitivity and a high hysteresis in the humidity response, in particular when operated at high temperature. PMMA mPOFBGs annealed at high humidity show higher and more linear humidity sensitivity with negligible hysteresis. We also report how annealing at high humidity can blue-shift the FBG wavelength more than 230 nm without loss in the grating strength.
RESUMEN
We have fabricated the first single-mode step-index and humidity insensitive polymer optical fiber operating in the 850 nm wavelength ranges. The step-index preform is fabricated using injection molding, which is an efficient method for cost effective, flexible and fast preparation of the fiber preform. The fabricated single-mode step-index (SI) polymer optical fiber (POF) has a 4.8µm core made from TOPAS grade 5013S-04 with a glass transition temperature of 134°C and a 150 µm cladding made from ZEONEX grade 480R with a glass transition temperature of 138°C. The key advantages of the proposed SIPOF are low water absorption, high operating temperature and chemical inertness to acids and bases and many polar solvents as compared to the conventional poly-methyl-methacrylate (PMMA) and polystyrene based POFs. In addition, the fiber Bragg grating writing time is short compared to microstructured POFs.
RESUMEN
We demonstrate fiber Bragg grating (FBG) writing in PMMA microstructured Polymer Optical Fibers (mPOFs) using UV Phase Mask technique with writing times shorter than 10 min. The shortest writing time was 6 minutes and 50 seconds and the longest writing time was 8 min and 50 sec. The FBGs were written in a 125 µm PMMA mPOF having 3-rings of holes, the reflection peaks were centred at 632.6 nm and have a reflectivity as high as 26 dB. We also demonstrate how the writing dynamics depends on the intensity of the writing beam.