Mechanically induced photons from ultraviolet-C to near-infrared in Tm3+-doped MgF2.

Mechanoluminescence (ML) plays a vital role in various fields, and has gained increasing popularity over the past two decades. The widely studied materials that are capable of generating ML can be classified into two groups, self-powered and trap-controlled. Here, we demonstrate that both self-powered ML and trap-controlled ML can be achieved simultaneously in MgF2:Tm3+. Upon stimulation of external force, the 1I6→3H6 and 3H4→3H6 transitions of Tm3+ are observed, ranging from the ultraviolet-C to near-infrared. After exposure to X-rays, MgF2:Tm3+ presents a stronger ML than the uncharged sample. After cleaning up at high temperatures, the ML returns to the initial level, which is a typical characteristic of trap-controlled ML. In the end, we demonstrate the potential applications of MgF2:Tm3+ in dynamic anti-counterfeiting, and structure inspection.

Redesign of air/oil-water interface via physical fields coupled with pH shifting to improve the emulsification, foaming, and digestion properties of plant proteins.

The application of plant proteins in food systems is largely hindered by their poor foaming or emulsifying properties and low digestibility compared with animal proteins, especially due to the aggregate state with tightly folded structure, slowly adsorbing at the interfaces, generating films with lower mechanical properties, and exposing less cutting sites. Physical fields and pH shifting have certain synergistic effects to efficiently tune the structure and redesign the interfacial layer of plant proteins, further enhancing their foaming or emulsifying properties. The improvement mechanisms mainly include: i) Aggregated plant proteins are depolymerized to form small protein particles and flexible structure is more easily exposed by combination treatment; ii) Particles with appropriate surface properties are quickly adsorbed to the interfacial layer, and then unfolded and rearranged to generate a tightly packed stiff interfacial layer to enhance bubble and emulsion stability; and iii) The unfolding and rearrangement of protein structure at the interface may result in the exposure of more cutting sites of digestive enzymes. This review summarizes the latest research progress on the structural changes, interfacial behaviors, and digestion properties of plant proteins under combined treatment, and elucidates the future development of these modification technologies for plant proteins in the food industry.

Two Organic-Inorganic Manganese(II) Halide Hybrids Showing Compelling Photo- and Mechanoluminescence as well as Rewritable Anticounterfeiting Printing.

Two organic-inorganic manganese(II) halide hybrids (OIMHs) with formulas of [(TEA)(TMA)]MnCl4 (1) and [(TPA)(TMA)3](MnCl4)2 (2) (TEA = tetraethylammonium, TMA = tetramethylammonium, and TPA = tetrapropylammonium) were synthesized by a mixed-ligand strategy. Both compounds crystallize in the acentric space group and are composed of isolated [MnCl4]2- tetrahedral units separated by two types of organic cations. They show high thermal stability and emit strong green light with different emission bandwidths, quantum yields, and high-temperature photostability. Remarkably, the quantum yield of 1 can reach up to 99%. Due to the high thermal stability and quantum yield of 1 and 2, green light-emitting diodes (LEDs) were fabricated. Furthermore, mechanoluminescence (ML) was observed in 1 and 2 when stress was applied. The ML spectrum of 1 is similar to the photoluminescence (PL) spectrum, suggesting ML and PL emissions come from the same transition of Mn(II) ions. Finally, rewritable anticounterfeiting printing and information storage were achieved by utilizing the outstanding photophysical properties and ionic features of the products. The printed images still remain clear after several cycles, and the information stored on the paper can be read out by a UV lamp and commercial mobile phones.

Molten Salt Shielded Synthesis of Monodisperse Layered CaZnOS-Based Semiconductors for Piezophotonic and X-Ray Detection Applications.

CaZnOS-based semiconductors are the only series of material system discovered that can simultaneously realize a large number of dopant elements to directly fulfill the highly efficient full-spectrum functionality from ultraviolet to near-infrared under the same force/pressure. Nevertheless, owing to the high agglomeration of the high temperature solid phase manufacturing process, which is unable to control the crystal morphology, the application progress is limited. Here, the authors report first that CaZnOS-based fine monodisperse semiconductor crystals with various doping ions are successfully synthesized by a molten salt shielded method in an air environment. This method does not require inert gas ventilation, and therefore can greatly reduce the synthesis cost and more importantly improve the fine control of the crystal morphology, along with the crystals' dispersibility and stability. These doped semiconductors can not only realize different colors of mechanical-to-optical energy conversion, but also can achieve multicolor luminescence under low-dose X-ray irradiation, moreover their intensities are comparable to the commercial NaI:Tl. They can pave the way to the new fields of advanced optoelectronic applications, such as piezophotonic systems, mechanical energy conversion and harvesting devices, intelligent sensors, and artificial skin as well as X-ray applications.

Mechanoluminescence ratiometric thermometry via MgF2:Tb3.

Mechanoluminescent materials have attracted considerable attention over the past two decades, owing to the ability to convert external mechanical stimuli into useful photons. Here we present a new, to the best of our knowledge, type of mechanoluminescent material, i.e., MgF2:Tb3+. In addition to the demonstration of traditional applications, such as stress sensing, we show the possibility of ratiometric thermometry using this mechanoluminescent material. Under stimulation of an external force, rather than the conventional photoexcitation, the luminescence ratio of 5D3→7F6 to 5D4→7F5 emission lines of Tb3+ is confirmed to be a good indicator of temperature. Our work not only expands the family of mechanoluminescent materials, but also provides a new and energy-saving route for temperature sensing.

Effective Repeatable Mechanoluminescence in Heterostructured Li1- x Nax NbO3 : Pr3.

Mechanoluminescence (ML) is a striking optical phenomenon that is achieved through mechanical to optical energy conversion. Here, a series of Li1 -x Nax NbO3 : Pr3+ (x = 0, 0.2, 0.5, 0.8, 1.0) ML materials have been developed. In particular, due to the formation of heterostructure, the synthesized Li0.5 Na0.5 NbO3 : Pr3+ effectively couples the trap structures and piezoelectric property to realize the highly repeatable ML performance without traditional preirradiation process. Furthermore, the ML performances measured under sunlight irradiation and preheating confirm that the ML properties of Li0.5 Na0.5 NbO3 : Pr3+ can be ascribed to the dual modes of luminescence mechanism, including both trap-controllable and self-recoverable modes. In addition, DFT calculations further confirm that the doping of Na+ ions in LiNbO3 leads to electronic modulations by the formation of the heterostructures, which optimizes the trap distributions and concentrations. These modulations improve the electron transfer efficiency to promote ML performances. This work has supplied significant references for future design and synthesis of efficient ML materials for broad applications.

"Energy Relay Center" for doped mechanoluminescence materials: a case study on Cu-doped and Mn-doped CaZnOS.

We unraveled the mechanisms of transition metal-doped mechanoluminescent materials through a case study of CaZnOS. We found that the native point defect levels in Cu or Mn-doped CaZnOS system acted as energy relay centers for luminescence energy transfer. In combination with native point defect levels, discussed in a previous study [Phys. Chem. Chem. Phys., 2016, 18, 25946], we found that phosphor luminescence belongs to two different mechanisms. For Cu-doping, it occurs by the path via the conduction band minimum to the Cu-t2g level of the 3d orbital localized in the band gap. The hole-drifting effect was found to support the reported red-shifting of the emission. Both reversible and irreversible mechanical quenching were attributed to the spatially separated electrons recombining with the hole localized on the Cu-t2g level within the gap at levels below or above respectively. For Mn-doping, this occurs by a collaborative luminescence assisted by native point defects, and the excited states of Mn2+ overlap with the conduction band edge. The coexistence of MnZn and MnCa was confirmed, but was relatively low in MnCa. The concentration quenching effect, as well as the red-shift of absorption, shows a strong correlation with native point defect levels and the relative position of the 4T1(4G) state for both MnZn and MnCa. Further simplified approximations were used for modeling such concentration quenching effects.

CdS@SiO2 Core-Shell Electroluminescent Nanorod Arrays Based on a Metal-Insulator-Semiconductor Structure.

Enormous advancement has been achieved in the field of one-dimensional (1D) semiconductor light-emitting devices (LEDs), however, LEDs based on 1D CdS nanostructures have been rarely reported. The fabrication of CdS@SiO2 core-shell nanorod array LEDs based on a Au-SiO2 -CdS metal-insulator-semiconductor (MIS) structure is presented. The MIS LEDs exhibit strong yellow emission with a low threshold voltage of 2.7 V. Electroluminescence with a broad emission ranging from 450 nm to 800 nm and a shoulder peak at 700 nm is observed, which is related to the defects and surface states of the CdS nanorods. The influence of the SiO2 shell thickness on the electroluminescence intensity is systematically investigated. The devices have a high light-emitting spatial resolution of 1.5 µm and maintain an excellent emission property even after shelving at room temperature for at least three months. Moreover, the fabrication process is simple and cost effective and the MIS device could be fabricated on a flexible substrate, which holds great potential for application as a flexible light source. This prototype is expected to open up a new route towards the development of large-scale light-emitting devices with excellent attributes, such as high resolution, low cost, and good stability.

Establishing the Structural Integrity of Core-Shell Nanoparticles against Elemental Migration using Luminescent Lanthanide Probes.

Core-shell structured nanoparticles are increasingly used to host luminescent lanthanide ions but the structural integrity of these nanoparticles still lacks sufficient understanding. Herein, we present a new approach to detect the diffusion of dopant ions in core-shell nanostructures using luminescent lanthanide probes whose emission profile and luminescence lifetime are sensitive to the chemical environment. We show that dopant ions in solution-synthesized core-shell nanoparticles are firmly confined in the designed locations. However, annealing at certain temperatures (greater than circa 350 °C) promotes diffusion of the dopant ions and leads to degradation of the integrity of the nanoparticles. These insights into core-shell nanostructures should enhance our ability to understand and use lanthanide-doped luminescent nanoparticles.

Insights into digestibility, biological activity, and peptide profiling of flaxseed protein isolates treated by ultrasound coupled with alkali cycling.

This study aims to investigate the effects of ultrasound coupled with alkali cycling on the structural properties, digestion characteristics, biological activity, and peptide profiling of flaxseed protein isolates (FPI). The digestibility of FPI obtained by ultrasound coupled with pH 10/12 cycling (UFPI-10/12) (74.56 % and 79.12 %) was significantly higher than that of native FPI (64.40 %), and UFPI-10 showed higher hydrolysis degree (35.76 %) than FPI (30.65 %) after intestinal digestion. The combined treatment induced transition from α-helix to ß-sheet with an orderly structure. Large FPI aggregates broke down into small-sized FPI particles, which induced the increase of specific surface area of particles. This might expose more cutting sites and contact area with enzymes. Furthermore, UFPI-10 showed high antioxidant activity (29.18 %) and lipid-lowering activity (70.52 %). Peptide profiling revealed that UFPI-10 exhibited a higher proportion of 300-600 Da peptides and significantly higher abundance of antioxidant peptides than native FPI, which might promote its antioxidant activity. Those results suggest that the combined treatment is a promising modification method to improve the digestion characteristics and biological activity of FPI. This work provides new ideas for widespread use of FPI as an active stabilizer in food systems.

Flavonoid-rich sesame leaf extract-mediated synthesis of nanozymes: Extraction optimization, chemical composition identification and bioactivity evaluation.

Sesame leaves contain rich phenolic acids and flavonoids. However, their potential in nanozyme synthesis has not been investigated yet. Herein, we report the preparation of flavonoid-rich sesame leaf extract (SLE), composition identification, and its use in the construction of iron (Fe)-based nanozymes (Fe-SLE CPNs). SLE was obtained with an extraction yield of ∼14.5% with a total flavonoid content (TFC) of ∼850.85 mg RE/g. There were 83 flavonoid compounds in SLE, primarily including scutellarin, apigenin-7-glucuronid, narcissin, and hyperoside. Fe-SLE CPNs exhibited nanodot morphology with a hydrodynamic size of 79.34 nm and good stability in various physiological solutions, pH levels, and temperatures. The Fe-SLE CPNs were more efficient in the scavenging ability of reactive oxygen species (ROS) than SLE alone. Furthermore, a stronger anti-inflammatory effect of the Fe-SLE CPNs was shown by modulating the MyD88-NF-κB-MAPK signaling pathways. These findings imply that SLE-based nanozymes hold great potential for diverse applications.

Soft gliadin nanoparticles at air/water interfaces: The transition from a particle-laden layer to a thick protein film.

HYPOTHESIS: Protein-based soft particles possess a unique interfacial deformation behavior, which is difficult to capture and characterize. This complicates the analysis of their interfacial properties. Here, we aim to establish how the particle deformation affects their interfacial structural and mechanical properties. EXPERIMENTS: Gliadin nanoparticles (GNPs) were selected as a model particle. We studied their adsorption behavior, the time-evolution of their morphology, and rheological behavior at the air/water interface by combining dilatational rheology and microstructure imaging. The rheology results were analyzed using Lissajous plots and quantified using the recently developed general stress decomposition (GSD) method. FINDING: Three distinct stages were revealed in the adsorption and rearrangement process. First, spherical GNPs (∼105 nm) adsorbed to the interface. Then, these gradually deformed along the interface direction to a flattened shape, and formed a firm viscoelastic 2D solid film. Finally, further stretching and merging of GNPs at the interface resulted in rearrangement of their internal structure to form a thick film with lower stiffness than the initial film. These results demonstrate that the structure of GNPs confined at the interface is controlled by their deformability, and the latter can be used to tune the properties of prolamin particle-based multiphase systems.

Regulation of interfacial mechanics of soy protein via co-extraction with flaxseed protein for efficient fabrication of foams and emulsions.

Enrichment of plant proteins with functionality is of great importance for expanding their application in food formulations. This study proposed an innovation to co-enrich soy protein and flaxseed protein to act as efficient interfacial stabilizers for generating foams and emulsions. The structure, interfacial properties, and functionalities of the soy protein-flaxseed protein natural nanoparticles (SFNPs) obtained by alkali extraction-isoelectric precipitation (AE) and salt extraction-dialysis (SE) methods were investigated. Overall, the foamability of AE-SFNPs (194.67 %) was 1.45-fold that of SE-SFNPs, due to their more flexible structure, smaller particle size, and suitable surface wettability, promoting diffusion and adsorption at the air-water interface. AE-SFNPs showed higher emulsion stability (140.89 min), probably because the adsorbed AE-SFNPs with smaller size displayed soft particle-like properties and stronger interfacial flexibility, and therefore could densely and evenly arrange at the interface, facilitating the formation of a stiff and solid-like interfacial layer, beneficial for more stable emulsion formation. The findings may innovatively expand the applications of SFNPs as food ingredients.

Microstrain-Stimulated Elastico-Mechanoluminescence with Dual-Mode Stress Sensing.

Elastico-mechanoluminescence technology has shown significant application prospects in stress sensing, artificial skin, remote interaction, and other research areas. Its progress mainly lies in realizing stress visualization and 2D or even 3D stress-sensing effects using a passive sensing mode. However, the widespread promotion of mechanoluminescence (ML) technology is hindered by issues such as high stress or strain thresholds and a single sensing mode based on luminous intensity. In this study, a highly efficient green-emitting ML with dual-mode stress-sensing characteristics driven by microscale strain is developed using LiTaO3:Tb3+. In addition to single-mode sensing based on the luminous intensity, the self-defined parameter (Q) is also introduced as a dual-mode factor for sensing the stress velocity. Impressively, the fabricated LiTaO3:Tb3+ film is capable of generating discernible ML signals even when supplied with strains as low as 500 µst. This is the current minimum strain value that can drive green-emitting ML. This study offers an ideal photonic platform for exploring the potential applications of rare-earth-doped elastico-ML materials in remote interaction devices, high-precision stress sensors, and single-molecule biological imaging.

Bright Circularly Polarized Mechanoluminescence from 0D Hybrid Manganese Halides.

Hybrid metal halides (HMHs) with efficient circularly polarized luminescence (CPL) have application prospects in many fields, due to their abundant host-guest structures and high photoluminescence quantum yield (PLQY). However, CPLs in HMHs are predominantly excited by light or electricity, limiting their use in multivariate environments. It is necessary to explore a novel excitation method to extend the application of chiral HMHs as smart stimuli-responsive optical materials. In this work, an enantiomeric pair of 0D hybrid manganese bromides, [H2(2R,4R)-(+)/(2S,4S)-(-)-2,4-bis(diphenylphosphino)pentane]MnBr4 [(R/S)-1] is presented, which exhibits efficient CPL emissions with near-unity PLQYs and high dissymmetry factors of ± 2.0 × 10-3. Notably, (R/S)-1 compounds exhibit unprecedented and bright circularly polarized mechanoluminescence (CPML) emissions under mechanical stimulation. Moreover, (R/S)-1 possess high mechanical force sensitivities with mechanoluminescence (ML) emissions detectable under 0.1 N force stimulation. Furthermore, this ML emission exhibits an extraordinary antithermal quenching effect in the temperature range of 300-380 K, which is revealed to originate from a thermal activation energy compensation mechanism from trap levels to Mn(II) 4T1 level. Based on their intriguing optical properties, these compounds as chiral force-responsive materials are demonstrated in multilevel confidential information encryption.

Modulating Smart Mechanoluminescent Phosphors for Multistimuli Responsive Optical Wood.

Mechanoluminescence is a smart light-emitting phenomenon in which applied mechanical energy is directly converted into photon emissions. In particular, mechanoluminescent materials have shown considerable potential for applications in the fields of energy and sensing. This study thoroughly investigates the mechanoluminescence and long afterglow properties of singly doped and codoped Sr2 MgSi2 O7 (SMSO) with varying concentrations of Eu2+ and Dy3+ ions. Subsequently, a comprehensive analysis of its multimode luminescence properties, including photoluminescence, mechanoluminescence, long afterglow, and X-ray-induced luminescence, is conducted. In addition, the density of states mapping is acquired through first-principles calculations, confirming that the enhanced mechanoluminescence properties of SMSO primarily stem from the deep trap introduced by Dy3+ . In contrast to traditional mixing with Polydimethylsiloxane, in this study, the powders are incorporated into optically transparent wood to produce a multiresponse with mechanoluminescence, long afterglow, and X-ray-excited luminescence. This structure is achieved by pretreating natural wood, eliminating lignin, and subsequently modifying the wood to overall modification using various smart phosphors and epoxy resin composites. After natural drying, a multifunctional composite wood structure with diverse luminescence properties is obtained. Owing to its environmental friendliness, sustainability, self-power, and cost-effectiveness, this smart mechanoluminescence wood is anticipated to find extensive applications in construction materials and energy-efficient displays.

Quantifying the interfacial triboelectricity in inorganic-organic composite mechanoluminescent materials.

Mechanoluminescence (ML) sensing technologies open up new opportunities for intelligent sensors, self-powered displays and wearable devices. However, the emission efficiency of ML materials reported so far still fails to meet the growing application requirements due to the insufficiently understood mechano-to-photon conversion mechanism. Herein, we propose to quantify the ability of different phases to gain or lose electrons under friction (defined as triboelectric series), and reveal that the inorganic-organic interfacial triboelectricity is a key factor in determining the ML in inorganic-organic composites. A positive correlation between the difference in triboelectric series and the ML intensity is established in a series of composites, and a 20-fold increase in ML intensity is finally obtained by selecting an appropriate inorganic-organic combination. The interfacial triboelectricity-regulated ML is further demonstrated in multi-interface systems that include an inorganic phosphor-organic matrix and organic matrix-force applicator interfaces, and again confirmed by self-oxidization and reduction of emission centers under continuous mechanical stimulus. This work not only gives direct experimental evidences for the underlying mechanism of ML, but also provides guidelines for rationally designing high-efficiency ML materials.

Modulating interfacial structure and lipid digestion of natural Camellia oil body by roasting and boiling processes.

Oil body (OB) is the lipid-storage organelle in oilseed, and its stability is crucial for oilseed processing. Herein, effects of roasting and boiling on the structure, stability, and in vitro lipid digestion of Camellia OB were studied. The interfacial structure and physical stability of the extracted OB were investigated by electrophoresis, confocal-Raman spectroscopy, zeta-potential, and surface hydrophobicity, etc. Boiling caused protein loss on the OB surfaces, forming a stable phospholipid interface, which resulted in coalescence of the droplets (d > 100 µm) and negative ζ-potential (-3 âˆ¼ -8 mV) values at a pH of 2.0. However, roasting partially denatured the proteins in the seeds, which were adsorbed on the OB surfaces. The random coil structure of interfacial protein increased to ∼20 % after thermal treatment. Besides, heating decreased the surface hydrophobicity of OB and improved lipid digestion. After boiling 60 min, the extent of lipolysis increased from 41.7 % (raw) to 57.4 %.

Mechanoluminescent Materials Enable Mechanochemically Controlled Atom Transfer Radical Polymerization and Polymer Mechanotransduction.

Organic mechanophores have been widely adopted for polymer mechanotransduction. However, most examples of polymer mechanotransduction inevitably experience macromolecular chain rupture, and few of them mimic mussel's mechanochemical regeneration, a mechanically mediated process from functional units to functional materials in a controlled manner. In this paper, inorganic mechanoluminescent (ML) materials composed of CaZnOS-ZnS-SrZnOS: Mn2+ were used as a mechanotransducer since it features both piezoelectricity and mechanolunimescence. The utilization of ML materials in polymerization enables both mechanochemically controlled radical polymerization and the synthesis of ML polymer composites. This procedure features a mechanochemically controlled manner for the design and synthesis of diverse mechanoresponsive polymer composites.

Mechanoluminescence and Photoluminescence Heterojunction for Superior Multimode Sensing Platform of Friction, Force, Pressure, and Temperature in Fibers and 3D-Printed Polymers.

Endowing a single material with various types of luminescence, that is, exhibiting a simultaneous optical response to different stimuli, is vital in various fields. A photoluminescence (PL)- and mechanoluminescence (ML)-based multifunctional sensing platform is built by combining heterojunctioned ZnS/CaZnOS:Mn2+ mechano-photonic materials using a 3D-printing technique and fiber spinning. ML-active particles are embedded in micrometer-sized cellulose fibers for flexible optical devices capable of emitting light driven by mechanical force. Individually modified 3D-printed hard units that exhibit intense ML in response to mechanical deformation, such as impact and friction, are also fabricated. Importantly, they also allow low-pressure sensing up to ≈100 bar, a range previously inaccessible by any other optical sensing technique. Moreover, the developed optical manometer based on the PL of the materials demonstrates a superior high-pressure sensitivity of ≈6.20 nm GPa-1 . Using this sensing platform, four modes of temperature detection can be achieved: excitation-band spectral shifts, emission-band spectral shifts, bandwidth broadening, and lifetime shortening. This work supports the possibility of mass production of ML-active mechanical and optoelectronic parts integrated with scientific and industrial tools and apparatus.