Superoleophobic Surfaces Obtained via Hierarchical Metallic Meshes.

Hierarchical metallic surfaces demonstrating pronounced water and oil repellence are reported. The surfaces were manufactured with stainless-steel microporous meshes, which were etched with perfluorononanoic acid. As a result, a hierarchical relief was created, characterized by roughness at micro- and sub-microscales. Pronounced superoleophobicity was registered with regard to canola, castor, sesame, flax, crude (petroleum), and engine oils. Relatively high sliding angles were recorded for 5 µL turpentine, olive, and silicone oil droplets. The stability of the Cassie-like air trapping wetting state, established with water/ethanol solutions, is reported. The omniphobicity of the surfaces is due to the interplay of their hierarchical relief and surface fluorination.

A novel micro-reactor for hydrogen production from solid NaBH4 hydrolysis in a dual-cycle methodology.

Hydrogen-based Fuel Cells (FCs) hold significant potential as energy conversion technologies. In a previous study, we presented a pump-based hydrogen generator (PHG) that utilizes a catalytic reaction between sodium borohydride (NaBH4) powder and water. The pump circulates the water solution through the powder chamber in a closed-loop reaction. The PHG demonstrated clear advantages over alternative hydrogen sources in terms of both safety and energy density. However, as operating time increases, the solution in the closed-loop PHG becomes saturated, causing the reaction rate to decline. This limitation can be overcome in cases where an external water source is available, such as marine vehicles, drones equipped with water recovery systems from their fuel cells, or systems located near pipelines. In such scenarios, introducing freshwater feeding and product emission offers intriguing possibilities for significantly enhancing the fuel's energy density and extending its effective operation time. Our current research introduces an innovative concept: a dual-cycle generator (DCG) that effectively overcomes the issue of solution saturation over time. It achieves this by combining solution circulation with freshwater feeding and product emission. Our study employed a DCG prototype to examine various operating modes and to demonstrate the effectiveness of this approach. The DCG achieved a calculated energy density for the fuel of 3868 Wh/kg, with 93% H2 extraction yield from the powder. Our findings reveal substantial improvements in terms of extended operation duration (81%), increased hydrogen flow rate (36%), enhanced energy density (33%), and improved H2 yield extraction from the powder (39%). This methodology holds promise for mobile applications or off-grid systems situated in proximity to a water source.

Laser-Induced Pd-PdO/rGO Catalysts for Enhanced Electrocatalytic Conversion of Nitrate into Ammonia.

Electrochemical reduction of nitrate to ammonia (eNO3RR) is proposed as a sustainable solution for high-rate ammonia synthesis under ambient conditions. The complex, multistep eNO3RR mechanism necessitates the use of a catalyst for the complete conversion of nitrate to ammonia. Our research focuses on developing a novel Pd-PdO doped in a reduced graphene oxide (rGO) composite catalyst synthesized via a laser-assisted one-step technique. This catalyst demonstrates dual functionality: palladium (Pd) boosts hydrogen adsorption, while its oxide (PdO) demonstrates considerable nitrogen adsorption affinity and exhibits a maximum ammonia yield of 5456.4 ± 453.4 µg/h/cm2 at -0.6 V vs reversible hydrogen electrode (RHE), with significant yields for nitrite and hydroxylamine under ambient conditions in a nitrate-containing alkaline electrolyte. At a lower potential of -0.1 V, the catalyst exhibited a minimal hydrogen evolution reaction of 3.1 ± 2.2% while achieving high ammonia selectivity (74.9 ± 4.4%), with the balance for nitrite and hydroxylamine. Additionally, the catalyst's stability and activity can be regenerated through the electrooxidation of Pd.

The Performance of a Modified Anode Using a Combination of Kaolin and Graphite Nanoparticles in Microbial Fuel Cells.

The bacterial anode in microbial fuel cells was modified by increasing the biofilm's adhesion to the anode material using kaolin and graphite nanoparticles. The MFCs were inoculated with G. sulfurreducens, kaolin (12.5 g·L-1), and three different concentrations of graphite (0.25, 1.25, and 2.5 g·L-1). The modified anode with the graphite nanoparticles (1.25 g·L-1) showed the highest electroactivity and biofilm viability. A potential of 0.59, 0.45, and 0.23 V and a power density of 0.54 W·m-2, 0.3 W·m-2, and 0.2 W·m-2 were obtained by the MFCs based on kaolin-graphite nanoparticles, kaolin, and bare anodes, respectively. The kaolin-graphite anode exhibited the highest Coulombic efficiency (21%) compared with the kaolin (17%) and the bare (14%) anodes. Scanning electron microscopy and confocal laser scanning microscopy revealed a large amount of biofilm on the kaolin-graphite anode. We assume that the graphite nanoparticles increased the charge transfer between the bacteria that are in the biofilm and are far from the anode material. The addition of kaolin and graphite nanoparticles increased the attachment of several bacteria. Thus, for MFCs that are fed with wastewater, the modified anode should be prepared with a pure culture of G. sulfurreducens before adding wastewater that includes non-exoelectrogenic bacteria.

Dynamics Management of Intermediate Water Storage in an Air-Breathing Single-Cell Membrane Electrode Assembly.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), a high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such an inflatable bag integrated with a single lightweight MEA FC has the potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, and the membrane's hydration state and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, and polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA (12 g) integrated with an inflatable dead-end hydrogen storage bag. Varying current densities (5, 10, and 15 mA/cm2) and cathode humidity levels (20, 50, and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

Anode amendment with kaolin and activated carbon increases electricity generation in a microbial fuel cell.

The bacterial anode is a key factor for microbial fuel cell (MFC) performance. This study examined the potential of kaolin (fine clay) to enhance bacteria and conductive particle attachment to the anode. The bio-electroactivity of MFCs based on a carbon-cloth anode modified by immobilization with kaolin, activated carbon, and Geobacter sulfurreducens (kaolin-AC), with only kaolin (kaolin), and a bare carbon-cloth (control) anodes were examined. When the MFCs were fed with wastewater, the MFCs based on the kaolin-AC, kaolin, and bare anodes produced a maximum voltage of 0.6 V, 0.4 V, and 0.25 V, respectively. The maximum power density obtained by the MFC based on the kaolin-AC anode was 1112 mW‧m-2 at a current density of 3.33 A‧m-2, 12% and 56% higher than the kaolin and the bare anodes, respectively. The highest Coulombic efficiency was obtained by the kaolin-AC anode (16%). The relative microbial diversity showed that Geobacter displayed the highest relative distribution of 64% in the biofilm of the kaolin-AC anode. This result proved the advantage of preserving the bacterial anode exoelectrogens using kaolin. To our knowledge, this is the first study evaluating kaolin as a natural adhesive for immobilizing exoelectrogenic bacteria to anode material in MFCs.

Chemical-Dealloying-Derived PtPdPb-Based Multimetallic Nanoparticles: Dimethyl Ether Electrocatalysis and Fuel Cell Application.

In this work, we report a novel multimetallic nanoparticle catalyst composed of Pt, Pd, and Pb and its electrochemical activity toward dimethyl ether (DME) oxidation in liquid electrolyte and polymer electrolyte fuel cells. Chemical dealloying of the catalyst with the lowest platinum-group metal (PGM) content, Pt2PdPb2/C, was conducted using HNO3 to tune the catalyst activity. Comprehensive characterization of the chemical-dealloying-derived catalyst nanoparticles unambiguously showed that the acid treatment removed 50% Pb from the nanoparticles with an insignificant effect on the PGM metals and led to the formation of smaller-sized nanoparticles. Electrochemical studies showed that Pb dissolution led to structural changes in the original catalysts. Chemical-dealloying-derived catalyst nanoparticles made of multiple phases (Pt, Pt3Pb, PtPb) provided one of the highest PGM-normalized power densities of 118 mW mgPGM-1 in a single direct DME fuel cell operated at low anode catalyst loading (1 mgPGM cm-2) at 70 °C. A possible DME oxidation pathway for these multimetallic catalysts was proposed based on an online mass spectrometry study and the analysis of the reaction products.

Effect of external voltage on Pseudomonas putida F1 in a bio electrochemical cell using toluene as sole carbon and energy source.

A bio electrochemical cell (BEC) was constructed as a typical two-chamber microbial fuel cell (MFC), except that it was operated under external voltage instead of constant resistance as in an MFC. The anode chamber contained a pure culture of Pseudomonas putida F1 grown in a minimal medium containing toluene as the sole carbon and energy source. Operating the BEC under external voltages of 75, 125, 175, 250 and 500 mV (versus an Ag/AgCl reference electrode) led to increased bacterial cell growth to an OD(600) of 0.62-0.75, while the control BEC, which was not connected to external voltage, reached an OD(600) of only 0.3. Examination of the current generated under external voltages of 75, 125, 175, 250 and 500 mV showed that the maximal currents were 11, 23, 28, 54 and 94 mA m(-2), respectively. Cyclic voltammetry experiments demonstrated an anodic peak at 270 mV, which may imply oxidation of a vital molecule. The average residual toluene concentration after 147 h in the BEC operated under external voltage was 22 %, whereas in the control BEC it was 81 %. Proteome analysis of bacterial cells grown in the BEC (125 mV) revealed two groups of proteins, which are ascribed to charge transfer in the bacterial cells and from the cell to the electrode. In conclusion, operating the BEC at 75-500 mV enabled growth of a pure culture of P. putida F1 and toluene degradation even in an oxygen-limited environment.

Four-electron oxygen reduction by brominated cobalt corrole.

The carbon-supported cobalt(III) complex of ß-pyrrole-brominated 5,10,15-tris(pentafluorophenyl)corrole [Co(tpfc)Br(8)/C] is introduced as a nonplatinum alternative for electrocatalytic oxygen reduction in aqueous solutions. Through systematic work, the basic kinetic parameters of this reaction were studied, using rotating ring disk electrode electrochemical methods in the pH range of 0-11. Pronounced catalytic activity was detected in acid solutions along with shifts of the Co(II)/Co(III) and O(2) redox couples to more positive values (onset of 0.56 V at pH 0). A series of independent measurements have been used to prove that the dominant mechanism for oxygen reduction by Co(tpfc)Br(8)/C catalysis is the direct four-electron pathway to water.

Hydrogen Production in Microbial Electrolysis Cells Based on Bacterial Anodes Encapsulated in a Small Bioreactor Platform.

Microbial electrolysis cells (MECs) are an emerging technology capable of harvesting part of the potential chemical energy in organic compounds while producing hydrogen. One of the main obstacles in MECs is the bacterial anode, which usually contains mixed cultures. Non-exoelectrogens can act as a physical barrier by settling on the anode surface and displacing the exoelectrogenic microorganisms. Those non-exoelectrogens can also compete with the exoelectrogenic microorganisms for nutrients and reduce hydrogen production. In addition, the bacterial anode needs to withstand the shear and friction forces existing in domestic wastewater plants. In this study, a bacterial anode was encapsulated by a microfiltration membrane. The novel encapsulation technology is based on a small bioreactor platform (SBP) recently developed for achieving successful bioaugmentation in wastewater treatment plants. The 3D capsule (2.5 cm in length, 0.8 cm in diameter) physically separates the exoelectrogenic biofilm on the carbon cloth anode material from the natural microorganisms in the wastewater, while enabling the diffusion of nutrients through the capsule membrane. MECs based on the SBP anode (MEC-SBPs) and the MECs based on a nonencapsulated anode (MEC control) were fed with Geobacter medium supplied with acetate for 32 days, and then with artificial wastewater for another 46 days. The electrochemical activity, chemical oxygen demand (COD), bacterial anode viability and relative distribution on the MEC-SBP anode were compared with the MEC control. When the MECs were fed with artificial wastewater, the MEC-SBP produced (at -0.6 V) 1.70 ± 0.22 A m-2, twice that of the MEC control. The hydrogen evolution rates were 0.017 and 0.005 m3 m-3 day-1, respectively. The COD consumption rate for both was about the same at 650 ± 70 mg L-1. We assume that developing the encapsulated bacterial anode using the SBP technology will help overcome the problem of contamination by non-exoelectrogenic bacteria, as well as the shear and friction forces in wastewater plants.

Edge Cooling of a Fuel Cell during Aerial Missions by Ambient Air.

During aerial missions of fuel-cell (FC) powered drones, the option of FC edge cooling may improve FC performance and durability. Here we describe an edge cooling approach for fixed-wing FC-powered drones by removing FC heat using the ambient air during flight. A set of experiments in a wind tunnel and numerical simulations were performed to examine the efficiency of FC edge cooling at various flight altitudes and cruise speeds. The experiments were used to validate the numerical model and prove the feasibility of the proposed method. The first simulation duplicated the geometry of the experimental setup and boundary conditions. The calculated temperatures of the stack were in good agreement with those of the experiments (within ±2 °C error). After validation, numerical models of a drone's fuselage in ambient air with different radiator locations and at different flight speeds (10-30 m/s) and altitudes (up to 5 km) were examined. It was concluded that onboard FC edge cooling by ambient air may be applicable for velocities higher than 10 m/s. Despite the low pressure, density, and Cp of air at high altitudes, heat removal is significantly increased with altitude at all power and velocity conditions due to lower air temperature.

Metal-Organic Polymer-Derived Interconnected Fe-Ni Alloy by Carbon Nanotubes as an Advanced Design of Urea Oxidation Catalysts.

The electrochemical urea oxidation reaction (UOR) is considered as a promising renewable source for harvesting energy from waste. We report a new synthetic design approach to produce an iron-nickel alloy nanocatalyst from a metal-organic polymer (MOP) by a single-step carbonization process at 500 °C, thus forming a core-shell of iron-nickel-coated carbon (C@FeNi) nanostructures wired by embedded carbon nanotubes (CNTs) (CNT/C@FeNi). Powder X-ray diffraction confirmed the formation of metallic FeNi3 alloy nanoparticles (∼20 to 28 nm). Our experimental results showed that MOP containing CNTs acquired an interconnected hierarchical topology, which prevented the collapse of its microstructure during pyrolysis. Hence, CNT/C@FeNi shows higher porosity (10 times) than C@FeNi. The electrochemical UOR in alkaline electrolytes on these catalysts was studied using cyclic voltammetry (CV). The result showed a higher anodic current (3.5 mA cm-2) for CNT/C@FeNi than for C@FeNi (1.1 mA cm-2) at 1.5 V/RHE. CNT/C@FeNi displayed good stability in chronoamperometry experiments and a lower Tafel slope (33 mV dec-1) than C@FeNi (41.1 mV dec-1). In this study, CNT/C@FeNi exhibits higher exchange current density (3.2 µA cm-2) than does C@FeNi (2 µA cm-2). The reaction rate orders of CNT/C@FeNi and C@FeNi at a kinetically controlled potential of 1.4 V/RHE were 0.5 and 0.9, respectively, higher than the 0.26 of ß-Ni(OH)2, Ni/Ni(OH)2 electrodes. The electrochemical impedance result showed a lower charge-transfer resistance for CNT/C@FeNi (61 Ω·cm-2) than for C@FeNi (162 Ω·cm-2), due to faster oxidation kinetics associated with the CNT linkage. Moreover, CNT/C@FeNi exhibited a lower Tafel slope and resistance and higher heterogeneity (25.2 × 10-5 cm s-1), as well as relatively high faradic efficiency (68.4%) compared to C@FeNi (56%). Thus, the carbon-coated FeNi3 core connected by CNT facilitates lower charge-transfer resistance and reduces the UOR overpotential.

Surface modifications of carbon nanodots reveal the chemical source of their bright fluorescence.

Fluorescent carbon nanodots (CNDs) have drawn increasing attention in recent years. These cost-effective and eco-friendly nanomaterials with bright fluorescence have been investigated as promising materials for electrooptic and bioimaging applications. However, the chemical source stimulating their strong fluorescence has not been completely identified to date. Depending on the chemical composition, two absorption peaks are observed in the visible range. In this study, we applied selected chemical modifications to CNDs in order to elucidate the correlation between the chemical structure and optical behavior of CNDs. Varying the amount of acetic acid in the synthesis process resulted in different effects on the absorbance and fluorescence photo-spectra. Specifically, at a low concentration (10%), the fluorescence is dramatically red shifted from 340 to 405 nm. Comprehensive characterization of the chemical modification by FTIR and XPS allows identification of the role of acetic acid in the reaction mechanism leading to the modified photoactivity. The functional group responsible for the 405 nm peak was identified as HPPT. We describe a chemical mechanism involving acetic acid that leads to an increased concentration of HPPT groups on the surface of the CNDs. Applying two additional independent chemical and consequently optical modifications namely solution pH and annealing on the nanodots further supports our proposed explanation. Understanding the molecular origin of CND fluorescence may promote the design and control of effective CND fluorescence in optical applications.

Simultaneous Mapping of Oxygen Reduction Activity and Hydrogen Peroxide Generation on Electrocatalytic Surfaces.

Electrochemical scanning probe microscopies have become valuable experimental tools, owing to their capability of capturing topographic features in addition to mapping the electrochemical activity of nanoscale oxygen reduction catalysts. However, most scanning probe techniques lack the ability to correlate topographic features with the electrochemical oxygen reduction and peroxide formation in real time. In this report, we show that it is indeed possible to construct high-resolution catalytic current maps at an electrified solid-liquid interface by placing a specially made Au-coated SiO2 Pt atomic force microscopy and scanning electrochemical microscopy (AFM-SECM) dual electrode tip approximately 4-8 nm above the reaction center. The catalytic current measured every 16 nm and high collection efficiency (≈90 %) of the reverse current of peroxide byproducts was also demonstrated with the help of the dual electrode tip. Simultaneous oxygen reduction and intermediate peroxide oxidation current mapping was demonstrated using this Au-coated SiO2 Pt probe on two model surfaces, namely highly oriented pyrolytic graphite and Pt nanoparticles (NPs) supported on a glassy carbon surface.

Electrochemical Ammonia Generation Directly from Nitrogen and Air Using an Iron-Oxide/Titania-Based Catalyst at Ambient Conditions.

Ammonia was produced electrochemically from nitrogen/air in aqueous alkaline electrolytes by using a Fe2O3/TiO2 composite catalyst under room temperature and atmospheric pressure. At an applied potential of 0.023 V versus reversible hydrogen electrode, the rate of ammonia formation was 1.25 × 10-8 mmol mg-1 s-1 at an overpotential of just 34 mV. This rate increased to 2.7 × 10-7 mmol mg-1 s-1 at -0.577 V. The chronoamperometric experiments on Fe2O3/TiO2/C clearly confirmed that Fe2O3 along with TiO2 shows superior nitrogen reduction reaction activity compared to Fe2O3 alone. Experimental parameters such as temperature and applied potential have a significant influence on the rate of ammonia formation. The activation energy of nitrogen reduction on the employed catalyst was found to be 25.8 kJ mol-1. Real-time direct electrochemical mass spectrometry analysis was used to monitor the composition of the evolved gases at different electrode potentials.

Nanoscale mapping of catalytic hotspots on Fe, N-modified HOPG by scanning electrochemical microscopy-atomic force microscopy.

The scanning electrochemical microscopy-atomic force microscopy (SECM-AFM) technique is used to map catalytic currents post Fe and N surface modification of graphitic carbon with an ultra-high resolution of 50 nm. The oxidation current of the partial reduction product, hydrogen peroxide, was also mapped in the same location in the graphitic carbon. The current mapping and ex situ spectroscopic evidence revealed that Fe-coordinated nitrogen sites formed both in the edge and basal planes of highly ordered pyrolytic graphite (HOPG) constitute the primary oxygen reduction catalytic sites in acid solutions of this important yet insufficiently understood class of catalysts.

Exfoliated molybdenum di-sulfide (MoS2) electrode for hydrogen production in microbial electrolysis cell.

The most widely reported catalyst in microbial electrochemical cells (MEC) cathodes is platinum (Pt). The disadvantages of Pt include its high cost and sensitivity to various molecules. In this research an exfoliated molybdenum di-sulfide (MoS2-EF) catalyst was synthesized. The size of the obtained particles was 200 ±â€¯50 nm, 50-fold smaller than the pristine MoS2 catalyst. The MoS2-EF Raman spectrum displays the E12g and A1g peaks at 373 cm-1 and 399 cm-1. Electrochemical characterization by linear sweep voltammetry (LSV) of a rotating disc electrode RDE showed that the current density of Pt in 0.5 M H2SO4 was 3.3 times higher than MoS2-EF. However, in phosphate buffer (pH-7) electrolyte this ratio diminished to 1.9. The polarization curve of Pt, MoS2-EF and the pristine MoS2 electrodes, at -1.3 V in MEC configuration in abiotic conditions exhibit current densities of 17.46, 12.67 and 3.09 mA cm-2, respectively. Hydrogen evolution rates in the same MEC with a Geobacter sulfurreducens anode and Pt, MoS2-EF and the pristine MoS2 cathodes were 0.106, 0.133 and 0.083 m3 d-1 m-3, respectively. The results in this study show that MoS2-EF led to highly purified hydrogen and that this catalyst can serve as an electrochemical active and cost-effective alternative to Pt.

Exceptionally Active and Stable Spinel Nickel Manganese Oxide Electrocatalysts for Urea Oxidation Reaction.

Spinel nickel manganese oxides, widely used materials in the lithium ion battery high voltage cathode, were studied in urea oxidation catalysis. NiMn2O4, Ni1.5Mn1.5O4, and MnNi2O4 were synthesized by a simple template-free hydrothermal route followed by a thermal treatment in air at 800 °C. Rietveld analysis performed on nonstoichiometric nickel manganese oxide-Ni1.5Mn1.5O4 revealed the presence of three mixed phases: two spinel phases with different lattice parameters and NiO unlike the other two spinels NiMn2O4 and MnNi2O4. The electroactivity of nickel manganese oxide materials toward the oxidation of urea in alkaline solution is evaluated using cyclic voltammetric measurements. Ni1.5Mn1.5O4 exhibits excellent redox characteristics and lower charge transfer resistances in comparison with other compositions of nickel manganese oxides and nickel oxide prepared under similar conditions.The Ni1.5Mn1.5O4modified electrode oxidizes urea at 0.29 V versus Ag/AgCl with a corresponding current density of 6.9 mA cm(-2). At a low catalyst loading of 50 µg cm(-2), the urea oxidation current density of Ni1.5Mn1.5O4 in alkaline solution is 7 times higher than that of nickel oxide and 4 times higher than that of NiMn2O4 and MnNi2O4, respectively.

Vertically Aligned Nitrogen-Doped Carbon Nanotube Carpet Electrodes: Highly Sensitive Interfaces for the Analysis of Serum from Patients with Inflammatory Bowel Disease.

The number of patients suffering from inflammatory bowel disease (IBD) is increasing worldwide. The development of noninvasive tests that are rapid, sensitive, specific, and simple would allow preventing patient discomfort, delay in diagnosis, and the follow-up of the status of the disease. Herein, we show the interest of vertically aligned nitrogen-doped carbon nanotube (VA-NCNT) electrodes for the required sensitive electrochemical detection of lysozyme in serum, a protein that is up-regulated in IBD. To achieve selective lysozyme detection, biotinylated lysozyme aptamers were covalently immobilized onto the VA-NCNTs. Detection of lysozyme in serum was achieved by measuring the decrease in the peak current of the Fe(CN)6(3-/4-) redox couple by differential pulse voltammetry upon addition of the analyte. We achieved a detection limit as low as 100 fM with a linear range up to 7 pM, in line with the required demands for the determination of lysozyme level in patients suffering from IBD. We attained the sensitive detection of biomarkers in clinical samples of healthy patients and individuals suffering from IBD and compared the results to a classical turbidimetric assay. The results clearly indicate that the newly developed sensor allows for a reliable and efficient analysis of lysozyme in serum.

Current production in a microbial fuel cell using a pure culture of Cupriavidus basilensis growing in acetate or phenol as a carbon source.

A microbial fuel cell (MFC) was operated with a pure culture of Cupriavidus basilensis bacterial cells growing in the anode compartment in a defined medium containing acetate or phenol. Operating this mediator-less MFC under a constant external resistor of 1 kΩ with acetate or phenol led to current generation of 902 and 310 mA m(-2) respectively. In the MFC which was operated using acetate or phenol, the current density measured from the plankton bacterial cells with a fresh electrode was 125 and 109 mA m(-2), respectively, whereas the current obtained with biofilm-covered electrodes in sterile medium was 541 and 228 mA m(-2) respectively. After 72 h in the MFC, 86% of the initial phenol concentration was removed, while only 64% was removed after the same time in the control MFC which was held at an open circuit potential (OCP). Furthermore, SEM and confocal microscopy analyses demonstrated a developed biofilm with a live C. basilensis population. In conclusion, in this study we demonstrated, for the first time, use of C. basilensis facultative aerobe bacterial cells in a MFC using acetate or phenol as the sole carbon source which led to electricity generation.