RESUMEN
The results of γ-radiation (2-72 kGy) and thermal-induced effects on BACs in Bi/Er codoped aluminosilicate fibers (BEDF) have been presented first in this paper. We observed that the radiation effect on on-off gain and optical absorption associated with BAC-Al and BAC-Si was insignificant, while the effect on luminescence was considerable. However, the effect on luminescence is caused by the radiation-induced darkening, which is likely linked to thermal bleachable Al-OHC point defects generated by γ-radiation. We carried out the thermal experiment and observed thermal bleaching of the γ-irradiated fiber at a low temperature of 300 °C. The observations indicate that, while γ-radiation could introduce significant background loss, BAC-Al and BAC-Si are fairly radiation resistant. This is the first time that BACs show good radiation resistance in irradiated BEDFs.
RESUMEN
Ultra-high intensity lasers in use are connected with ionizing radiation sources that raise a real concern in relation to installations, personnel, population and environment protection. The shielding of target areas in these facilities has to be evaluated from the conceptual stage of the building design. The sizing of the protective concrete walls was determined using computer codes such as Fluka. For the experiments to be carried out in the facility of the Center for Advanced Laser Technologies (CETAL), both proton beams with the energy of 100 MeV and electron beams with 300 MeV energy were considered to calculate the dimensions of structural shielding and to establish technical solutions fulfilling the radiation protection constraints imposed by the National Commission for Nuclear Activities Control.
Asunto(s)
Rayos Láser , Protección Radiológica , Equipos de Seguridad , Protones , SeguridadRESUMEN
We investigate the effects of γ irradiation on bismuth active centres (BACs) and related photoluminescence properties of bismuth/erbium co-doped silica fibre (BEDF), [Si] ~28, [Ge] ~1.60, [Al] ~0.10, [Er] ~ <0.10 and [Bi] ~0.10 atom%, fabricated by in-situ solution doping and Modified Chemical Vapor Deposition (MCVD). The samples were irradiated at 1 kGy, 5 kGy, 15 kGy, 30 kGy and 50 kGy doses, and dose rate of 5.5 kGy/h, at room temperature. The optical properties of BEDF samples are tested before and after γ irradiation. We found that high dose γ irradiation could significantly influence the formation and composition of BACs and their photoluminescence performance, as important changes in absorption and emission properties associated with the 830 nm pump produces the direct evidence of γ irradiation effects on BAC-Si. We notice that the saturable to unsaturable absorption ratio at pump wavelength could be increased with high dose γ irradiation, indicating that emission and pump efficiency could be increased by γ irradiation. Our experimental results also reveal good radiation survivability of the BEDF under low and moderate γ irradiation. Our investigation suggests the existence of irradiation related processing available for tailoring the photoluminescence properties and performance of bismuth doped/co-doped fibres.
RESUMEN
This article presents an overview of the recent developments and requirements in radiotherapy dosimetry, with particular emphasis on the development of optical fibre dosemeters for radiotherapy applications, focusing particularly on in vivo applications. Optical fibres offer considerable advantages over conventional techniques for radiotherapy dosimetry, owing to their small size, immunity to electromagnetic interferences, and suitability for remote monitoring and multiplexing. The small dimensions of optical fibre-based dosemeters, together with being lightweight and flexible, mean that they are minimally invasive and thus particularly suited to in vivo dosimetry. This means that the sensor can be placed directly inside a patient, for example, for brachytherapy treatments, the optical fibres could be placed in the tumour itself or into nearby critical tissues requiring monitoring, via the same applicators or needles used for the treatment delivery thereby providing real-time dosimetric information. The article outlines the principal sensor design systems along with some of the main strengths and weaknesses associated with the development of these techniques. The successful demonstration of these sensors in a range of different clinical environments is also presented.