Cs-RHO Goes from Worst to Best as Water Enhances Equilibrium CO2 Adsorption via Phase Change.

The strong affinity of water to zeolite adsorbents has made adsorption of CO2 from humid gas mixtures such as flue gas nearly impossible under equilibrated conditions. Here, in this manuscript, we describe a unique cooperative adsorption mechanism between H2O and Cs+ cations on Cs-RHO zeolite, which actually facilitates the equilibrium adsorption of CO2 under humid conditions. Our data demonstrate that, at a relative humidity of 5%, Cs-RHO adsorbs 3-fold higher amounts of CO2 relative to dry conditions, at a temperature of 30 °C and CO2 pressure of 1 bar. A comparative investigation of univalent cation-exchanged RHO zeolites with H+, Li+, Na+, K+, Rb+, and Cs+ shows an increase of equilibrium CO2 adsorption under humid versus dry conditions to be unique to Cs-RHO. In situ powder X-ray diffraction indicates the appearance of a new phase with Im3̅m symmetry after H2O saturation of Cs-RHO. A mixed-cation exchanged NaCs-RHO exhibits similar phase transitions after humid CO2 adsorption; however, we found no evidence of cooperativity between Cs+ and Na+ cations in adsorption, in single-component H2O and CO2 adsorption. We hypothesize based on previous Rietveld refinements of CO2 adsorption in Cs-RHO zeolite that the observed phase change is related to solvation of extra-framework Cs+ cations by H2O. In the case of Cs-RHO, molecular modeling results suggest that hydration of these cations favors their migration from an original D8R position to S8R sites. We posit that this movement enables a trapdoor mechanism by which CO2 can interact with Cs+ at S8R sites to access the α-cage.

Selective Catalytic Chemistry at Rhodium(II) Nodes in Bimetallic Metal-Organic Frameworks.

We report the first study of a gas-phase reaction catalyzed by highly dispersed sites at the metal nodes of a crystalline metal-organic framework (MOF). Specifically, CuRhBTC (BTC3- =benzenetricarboxylate) exhibited hydrogenation activity, while other isostructural monometallic and bimetallic MOFs did not. Our multi-technique characterization identifies the oxidation state of Rh in CuRhBTC as +2, which is a Rh oxidation state that has not previously been observed for crystalline MOF metal nodes. These Rh2+ sites are active for the catalytic hydrogenation of propylene to propane at room temperature, and the MOF structure stabilizes the Rh2+ oxidation state under reaction conditions. Density functional theory calculations suggest a mechanism in which hydrogen dissociation and propylene adsorption occur at the Rh2+ sites. The ability to tailor the geometry and ensemble size of the metal nodes in MOFs allows for unprecedented control of the active sites and could lead to significant advances in rational catalyst design.

Synthesis of Highly Active Pd@Cu-Pt/C Methanol Oxidation Electrocatalysts via Continuous, Co-Electroless Deposition.

Controlled deposition of metals is essential for the creation of bimetallic catalysts having predictable composition and character. Continuous co-electroless deposition (co-ED) permits the creation of bimetallic catalysts with predictive control over composition. This method was applied to create a suite of Cu-Pt mixed-metal shell catalysts for use in methanol electrooxidation in direct methanol fuel cell applications (DMFCs). Enhanced performance of Cu-Pt compositions over Pt alone was predicted by existing computational studies in the literature. Experimental evidence from this study supports the bifunctional catalyst explanation for enhanced activity and confirms the optimum Cu:Pt ratio as Cu3Pt for this methanol electrooxidation. This ability to control the composition of a bimetallic shell can be extended to other systems where the ratio of two metals is critical for catalytic performance.

Fabrication of biodegradable particles with tunable morphologies by the addition of resveratrol to oil in water emulsions.

Particles for biomedical applications can be produced by emulsifying biocompatible polymers dissolved in an organic solvent in water. The emulsion is then transferred to an extraction bath that removes the solvent from the dispersed droplets, which leads to polymer precipitation and particle formation. Typically, the particles are smooth and spherical, likely because the droplets remain fluid throughout the solvent extraction process allowing minimization of surface area as the volume decreases. Few modifications to this technique exist that alter the spherical geometry, even though particle performance, from drug delivery to engaging cells of the body, can be tuned with morphology. Here we demonstrate that incorporation of resveratrol, with the aid of ethanol, into the oil phase of an emulsion of poly(lactide-co-glycolide) and dichloromethane in aqueous poly(vinyl alcohol) leads to a crumpled particle morphology. Video microscopy of particle formation revealed that during solvent extraction the droplet crumples in on itself, which does not occur when only ethanol is added to the emulsion. It is unclear why this occurs with resveratrol, but its hydroxyl groups appear to be optimally positioned because removal of the 4' hydroxyl or addition of a 3' hydroxyl resulted in a loss of crumpled particle morphology. We demonstrate that particle morphology can be tuned from that of a crumpled sheet of paper to a deflated sphere by switching out ethanol for a different cosolvent. We quantify the degree of particle deformation with surface area calculated from krypton adsorption isotherms and BET theory and find surface area correlates with resveratrol loading in the particle. Furthermore, spherical particles are achieved when ethyl acetate is used in lieu of dichloromethane and a cosolvent. We propose that during solvent extraction, resveratrol accumulates at the droplet surface where it inhibits polymer chain motion necessary to maintain a spherical geometry and the role of cosolvent is to redistribute resveratrol from the droplet bulk to its surface. This method of producing nonspherical particles extends to polycaprolactone and poly(L-lactic acid) and is compatible with the encapsulation of a hydrophobic fluorescent dye, suggesting hydrophobic bioactive agents could be encapsulated. Taken together, we demonstrate an ability to control morphology of biocompatible polymer particles produced by the widely practiced oil-in-water/solvent extraction protocol via the addition of resveratrol and a cosolvent to the oil phase. The methodology reported is straight forward, and scalable, and expected to be of utility in applications in which a deviation from the default smooth, spherical morphology is desired.