RESUMEN
In this Letter, we demonstrate 8°-tilted fiber Bragg grating (TFBG) inscription in single-mode step-index TOPAS/ZEONEX polymer optical fibers (POFs) using a 520â nm femtosecond laser and the line-by-line (LbL) writing technique. As a result of the tilt angle and the fiber refractive index, a large spectral range of cladding mode resonances covering 147â nm is obtained. The evolution of the transmitted spectrum is analyzed as a function of the surrounding refractive index (SRI) in a large range from 1.30 to 1.50. The cutoff cladding mode shows a refractive index sensitivity of 507â nm/RIU (refractive index unit). For single-resonance tracking near the cutoff mode, the sensitivity is at least 6â nm/RIU, depending on the exact wavelength position of the cladding modes. The main originality of our work is that it produces, for the first time, to the best of our knowledge, a TFBG in POF that operates in the refractive index range of aqueous solutions. The sensing capability for a large range of refractive index values is also relevant for (bio)chemical sensing in different media.
RESUMEN
The use of simpler and less bulky equipment, with a reliable performance and at relative low cost is increasingly important when assembling sensing configurations for a wide variety of applications. Based on this concept, this paper proposes a simple, efficient and relative low-cost fiber Bragg grating (FBG) interrogation solution using ultra-short FBGs (USFBGs) as edge filters. USFBGs with different lengths and reflection bandwidths were produced in silica optical fiber and in poly(methyl methacrylate) (PMMA) microstructured polymer optical fiber (mPOF), and by adjusting specific inscription parameters and the diffraction pattern, these gratings can present self-apodization and unique spectral characteristics suitable for filtering operations. In addition to being a cost-effective edge filter solution, USFBGs and standard uniform FBGs in silica fiber have similar thermal sensitivities, which results in a straightforward operation without complex equipment or calculations. This FBG interrogation configuration is also quite promising for dynamic measurements, and due to its multiplexing capabilities multiple USFBGs can be inscribed in the same optical fiber, allowing to incorporate several filters with identical or different spectral characteristics at specific wavelength regions in the same fiber, thus showing great potential to create and develop new sensing configurations.
RESUMEN
We demonstrate a simple and power stable 1.5-10.5 µm cascaded mid-infrared 3 MHz supercontinuum fiber laser. To increase simplicity and decrease cost, the design of the fiber cascade is optimized so that no thulium amplifier is needed. Despite the simple design with no thulium amplifier, we demonstrate a high average output power of 86.6 mW. Stability measurements for seven days with 8-9 h operation daily revealed fluctuations in the average power with a standard deviation of only 0.43% and a power spectral density stability of ±0.18dBm/nm for wavelengths <10µm. The high-repetition-rate, robust, and cheap all-fiber design makes this source ideal for applications in spectroscopy and imaging.
RESUMEN
We report on mid-infrared optical coherence tomography (OCT) at 4 µm based on collinear sum-frequency upconversion and promote the A-scan scan rate to 3 kHz. We demonstrate the increased imaging speed for two spectral realizations, one providing an axial resolution of 8.6 µm, and one providing a record axial resolution of 5.8 µm. Image performance is evaluated by sub-surface micro-mapping of a plastic glove and real-time monitoring of CO2 in parallel with OCT imaging.
RESUMEN
We experimentally investigate the influence of varying pulse parameters on the spectral broadening, power spectral density, and relative intensity noise of mid-infrared (mid-IR) in-amplifier cascaded supercontinuum generation (SCG) by varying the pulse duration (35 ps, 1 ns, 3 ns) and repetition rate (100, 500, 1000 kHz). The system is characterized at the output of the erbium-ytterbium-doped in-amplifier SCG stage, the thulium/germanium power redistribution stage, and the passive ZBLAN fiber stage. In doing so, we demonstrate that the output of the later stages depends critically on the in-amplifier stage, and relate this to the onset of modulation instability.
RESUMEN
In this paper, an endlessly single mode microstructured polymer optical fiber (mPOF) in a Mach-Zehnder (M-Z) interferometer configuration is demonstrated for temperature and strain measurement. Because there is no commercial splicer applied for POF-silica optical fiber (SOF) connectorization, prior to the M-Z interferometric sensing, we introduce an imaging projecting method to align a polycarbonate mPOF to a SOF and then the splice is cured permanently using ultraviolet (UV) glue. A He-Ne laser beam at 632.8 nm coupled in a SOF is divided by a 1 × 2 fiber coupler to propagate in two fiber arms. A piece of mPOF is inserted in one arm for sensing implementation and the interference fringes are monitored by a camera. For non-annealed fiber, the temperature sensitivity is found to be 25.5 fringes/°C for increasing temperature and 20.6 fringes/°C for decreasing temperature. The converted sensitivity per unit length is 135.6 fringes/°C/m for increasing temperature, which is twice as much as the silica fiber, or 852.2 rad/°C/m (optical phase change versus fiber temperature), which is more than four times as much as that for the PMMA fiber. To solve the sensitivity disagreement, the fiber was annealed at 125 °C for 36 h. Just after the thermal treatment, the temperature measurement was conducted with sensitivities of 16.8 fringes/°C and 21.3 fringes/°C for increasing and decreasing process, respectively. One month after annealing, the linear response was improved showing a temperature sensitivity of ~20.7 fringes/°C in forward and reverse temperature measurement. For the strain measurement based on non-annealed fiber, the sensitivity was found to be ~1463 fringes/%ε showing repeatable linear response for forward and reverse strain. The fiber axial force sensitivity was calculated to be ~2886 fringes/N, showing a force measurement resolution of ~3.47 × 10-4 N. The sensing methodology adopted in this work shows several advantages, such as very low cost, high sensitivity, a straightforward sensing mechanism, and ease of fabrication.
RESUMEN
We present the first Bragg gratings fabricated in two, three and five rings undoped PMMA microstructured polymer optical fibres (mPOFs) with relative low cost 266 nm Nd:YAG laser in the 850 nm region. The fibers were connectorised with commercial ferrules for easy coupling with silica patch cables. Temperature, humidity and strain sensitivities are measured and also the impact of ring structure and the diameter of POF on the characterization measurements are studied for potential applications. We also analyzed the effect of the number of hexagonal rings structure in gratings fabrication, noticing that larger number of rings lead to more difficulties to obtain strong gratings, where we consider this performance due to the scattering effects. We demonstrate Bragg gratings fabrication in 5-rings structure mPOF after 6 min by using 266 nm Nd:YAG laser whereas no Bragg gratings have been fabricated so far using 325 nm He-Cd laser system. Up to 30 dB relative reflected power gratings are obtained in two rings mPOF, showing good time stability and promising results for undoped mPOF applications.
RESUMEN
Improved long-wavelength transmission and supercontinuum (SC) generation is demonstrated by antireflective (AR) nanoimprinting and tapering of chalcogenide photonic crystal fibers (PCFs). Using a SC source input spanning from 1 to 4.2 µm, the total transmission of a 15 µm core diameter PCF was improved from â¼53% to â¼74% by nanoimprinting of AR structures on both input and output facets of the fiber. Through a combined effect of reduced reflection and redshifting of the spectrum to 5 µm, the relative transmission of light >3.5 µm in the same fiber was increased by 60.2%. Further extension of the spectrum to 8 µm was achieved using tapered fibers. The spectral broadening dynamics and output power were investigated using different taper parameters and pulse repetition rates.
RESUMEN
We obtained chirped gratings by performing hot water gradient thermal annealing of uniform poly (methylmethacrylate) (PMMA) microstructured polymer optical fiber Bragg gratings (POFBGs). The proposed method's simplicity is one of its main advantages because no special phase mask or additional etching are needed. It not only enables easy control tuning of the central wavelength and chirp characteristics, but it also leads to obtain flexible grating response, compared with tapered chirped POFBGs. Therefore, a flexible and low-cost chirped POFBG devices fabrication technique has been presented by using a single uniform phase mask.
RESUMEN
An endlessly single-mode doped microstructured poly(methyl methacrylate) (PMMA) optical fiber is produced for effective fiber Bragg grating (FBG) photo-inscription by means of a 400 nm femtosecond pulsed laser and the phase mask technique. The fiber presents a uniform benzyl dimethyl ketal (BDK) distribution in its core without drastic loss increase. It was produced using the selected center hole doping technique, and the BDK dopant acts as a photoinitiator. In this Letter, we report a rapidly growing process of the grating reflection band. For an 11 mW mean laser power, the FBG reflectivity reaches 83% in only 40 s.
RESUMEN
In this Letter, we report for the first time, to the best of our knowledge, the fabrication and characterization of a Zeonex/PMMA microstructured polymer optical fiber (mPOF) Bragg grating sensor for simultaneous monitoring of relative humidity (RH) and temperature. The sensing element (probe) is based on two separate in-line fiber Bragg gratings (FBGs) inscribed in the fabricated mPOF. A root mean square deviation of 0.8% RH and 0.6°C in the range of 10%-90% RH and 20°C-80°C was found. The developed mPOFBG sensor constitutes an efficient route toward low-cost, easy-to-fabricate and compact multi-parameter sensing solutions.
RESUMEN
The effect of humidity on annealing of poly (methyl methacrylate) (PMMA) based microstructured polymer optical fiber Bragg gratings (mPOFBGs) and the resulting humidity responsivity are investigated. Typically annealing of PMMA POFs is done in an oven without humidity control around 80°C and therefore at low humidity. We demonstrate that annealing at high humidity and high temperature improves the performances of mPOFBGs in terms of stability and sensitivity to humidity. PMMA POFBGs that are not annealed or annealed at low humidity level will have a low and highly temperature dependent sensitivity and a high hysteresis in the humidity response, in particular when operated at high temperature. PMMA mPOFBGs annealed at high humidity show higher and more linear humidity sensitivity with negligible hysteresis. We also report how annealing at high humidity can blue-shift the FBG wavelength more than 230 nm without loss in the grating strength.
RESUMEN
We have fabricated the first single-mode step-index and humidity insensitive polymer optical fiber operating in the 850 nm wavelength ranges. The step-index preform is fabricated using injection molding, which is an efficient method for cost effective, flexible and fast preparation of the fiber preform. The fabricated single-mode step-index (SI) polymer optical fiber (POF) has a 4.8µm core made from TOPAS grade 5013S-04 with a glass transition temperature of 134°C and a 150 µm cladding made from ZEONEX grade 480R with a glass transition temperature of 138°C. The key advantages of the proposed SIPOF are low water absorption, high operating temperature and chemical inertness to acids and bases and many polar solvents as compared to the conventional poly-methyl-methacrylate (PMMA) and polystyrene based POFs. In addition, the fiber Bragg grating writing time is short compared to microstructured POFs.
RESUMEN
The authors wish to make a change to the published paper [...].
RESUMEN
We experimentally report fiber Bragg gratings (FBGs) in a single mode step-index polymer optical fiber (POF) with a core made of TOPAS and cladding made of ZEONEX using 520 nm femtosecond pulses and a point-by-point (PbP) inscription method. With different pulse energies between 9.7 nJ and 11.2 nJ, 12 FBGs are distributed along the cores of two pieces of POFs with negative averaged effective index change up to ~6 × 10−4 in the TOPAS. For POF 1 with FBGs 16, the highest reflectivity 45.1% is obtained with a pulse energy of 10.6 nJ. After inscription, good grating stability is reported. Thanks to the post-annealing at 125 °C for 24 h, after cooling the grating reflectivity increases by ~10%. For POF 2 with FBGs 712, similar FBG data are obtained showing good reproducibility. Then, the FBGs are annealed at 125 °C for 78 h, and the average reflectivity of the FBGs during the annealing process increases by ~50% compared to that before the annealing, which could be potentially applied to humidity insensitive high temperature measurement.
RESUMEN
Light scattering is a fundamental property that can be exploited to create essential devices such as particle analysers. The most common particle size analyser relies on measuring the angle-dependent diffracted light from a sample illuminated by a laser beam. Compared to other non-light-based counterparts, such a laser diffraction scheme offers precision, but it does so at the expense of size, complexity and cost. In this paper, we introduce the concept of a new particle size analyser in a collimated beam configuration using a consumer electronic camera and machine learning. The key novelty is a small form factor angular spatial filter that allows for the collection of light scattered by the particles up to predefined discrete angles. The filter is combined with a light-emitting diode and a complementary metal-oxide-semiconductor image sensor array to acquire angularly resolved scattering images. From these images, a machine learning model predicts the volume median diameter of the particles. To validate the proposed device, glass beads with diameters ranging from 13 to 125 µm were measured in suspension at several concentrations. We were able to correct for multiple scattering effects and predict the particle size with mean absolute percentage errors of 5.09% and 2.5% for the cases without and with concentration as an input parameter, respectively. When only spherical particles were analysed, the former error was significantly reduced (0.72%). Given that it is compact (on the order of ten cm) and built with low-cost consumer electronics, the newly designed particle size analyser has significant potential for use outside a standard laboratory, for example, in online and in-line industrial process monitoring.