In Situ Construction of a Multifunctional Interphase Enabling Continuous Capture of Unstable Lattice Oxygen Under Ultrahigh Voltages.

The use of nickel-rich layered materials as cathodes can boost the energy density of lithium batteries. However, developing a safe and long-term stable nickel-rich layered cathode is challenging primarily due to the release of lattice oxygen from the cathode during cycling, especially at high voltages, which will cause a series of adverse effects, leading to battery failure and thermal runaway. Surface coating is often considered effective in capturing active oxygen species; however, its process is rather complicated, and it is difficult to maintain intact on the cathode with large volume changes during cycling. Here, we propose an in situ construction of a multifunctional cathode/electrolyte interphase (CEI), which is easy to prepare, repairable, and, most importantly, capable of continuously capturing active oxygen species during the entire life span. This unique protective mechanism notably improves the cycling stability of Li||LiNi0.8Co0.1Mn0.1O2 (NCM811) cells at rigorous working conditions, including ultrahigh voltage (4.8 V), high temperature (60 °C), and fast charging (10 C). An industrial 1 A h graphite||NCM811 pouch cell achieved stable operation of 600 cycles with a capacity retention of 79.6% at 4.4 V, exhibiting great potential for practical use. This work provides insightful guidance for constructing a multifunctional CEI to bypass limitations associated with high-voltage operations of nickel-rich layered cathodes.

Self-Assembly of Ultrathin, Ultrastrong Layered Membranes by Protic Solvent Penetration.

Flexible membranes with ultrathin thickness and excellent mechanical properties have shown great potential for broad uses in solid polymer electrolytes (SPEs), on-skin electronics, etc. However, an ultrathin membrane (<5 µm) is rarely reported in the above applications due to the inherent trade-off between thickness and antifailure ability. We discover a protic solvent penetration strategy to prepare ultrathin, ultrastrong layered films through a continuous interweaving of aramid nanofibers (ANFs) with the assistance of simultaneous protonation and penetration of a protic solvent. The thickness of a pure ANF film can be controlled below 5 µm, with a tensile strength of 556.6 MPa, allowing us to produce the thinnest SPE (3.4 µm). The resultant SPEs enable Li-S batteries to cycle over a thousand times at a high rate of 1C due to the small ionic impedance conferred by the ultrathin characteristic and regulated ionic transportation. Besides, a high loading of the sulfur cathode (4 mg cm-2) with good sulfur utilization was achieved at a mild temperature (35 °C), which is difficult to realize in previously reported solid-state Li-S batteries. Through a simple laminating process at the wet state, the thicker film (tens of micrometers) obtained exhibits mechanical properties comparable to those of thin films and possesses the capability to withstand high-velocity projectile impacts, indicating that our technique features a high degree of thickness controllability. We believe that it can serve as a valuable tool to assemble nanomaterials into ultrathin, ultrastrong membranes for various applications.

High-Performance 3D Stacked Micro All-Solid-State Thin-Film Lithium-Ion Batteries Based on the Stress-Compensation Effect.

A novel all-solid-state thin-film lithium-ion battery (LIB) is presented to address the trade-off issue between the specific capacity and stabilities in a conventional LIB. Different from the conventional one, this LIB device consists of two same LIB components located at the front and back surfaces of the substrate, respectively. These two LIB components form parallel connection by using the conductive through vias distributed in the substrate. Compared with the conventional one, this LIB device doubles the areal specific capacity. More importantly, due to the stress-compensation effect, this device effectively suppresses the stress induced by its volume changes resulting from the lithiation/delithiation processes and thermal expansion. Consequently, this device shows good cycling and thermal stabilities even when working at an industrial-grade high temperature of 125 °C. To further improve the specific capacity without sacrificing the stabilities, a 3D stacked LIB is successfully realized by using this LIB device as the cell, in which each cell is parallelly connected by using the above-mentioned conductive through vias. This 3D stacked LIB is experimentally demonstrated to obtain high specific capacity (79.9 µAh cm-2) and good stabilities (69.3% of retained capacity after 100 cycles at 125 °C) simultaneously.

Copper-doped Lanthanide Coordination Polymers as Luminescent Nanoenzyme for Ratiometric Sensing of H2O2 and Glutathione.

Design and fabrication of integrated multifunctional probes with intrinsic catalytic and detection abilities is of great importance to simplify the operation in biosensing application with high sensitivity. Herein, dual-emitting lanthanide coordination polymers (Ln-CPs) were facilely prepared by self-assembly of guanine diphosphate (GDP), terephthalic acid (TA), Tb3+ and Cu2+ designated as Tb/Cu-GDP/TA CPs. The doped Cu2+ endowed CPs with obviously enhanced peroxidase mimicking activity compared with free Cu2+. In the presence of H2O2, the probe catalyzed the oxidation of TA generating a new blue fluorescent product, while the fluorescence of Tb3+ decreased simultaneously. Therefore, a new sensitive ratiometric fluorescent sensor for H2O2 has been developed with a good linear range from 0.01 to 300 µM and limit of 1.62 nM. Moreover, the proposed platform could be extended to GSH ratiometric assay in the presence of H2O2, and interestingly, the detection performance could be easily adjusted by adding different concentration of H2O2. This work will facilitate the development of luminescent nanoenzymes based on Ln-CPs to construct the simple ratiomatric sensing platform.

H2O2 Significantly Affects Larix kaempferi × Larix olgensis Somatic Embryogenesis.

Larch is widely distributed throughout the world and is an important species for timber supply and the extraction of industrial raw materials. In recent years, the hybrid breeding of Larix kaempferi and Larix olgensis has shown obvious heterosis in quick-growth, stress resistance and wood properties. However, its growth and development cycle is too long to meet general production needs. In order to shorten the breeding cycle, we have for the first time successfully established and optimized a somatic embryogenesis system for Larix kaempferi × Larix olgensis. We found that the highest rate of embryonal-suspensor mass (ESM) induction was observed when late cotyledonary embryos were used as explants. The induced ESMs were subjected to stable proliferation, after which abscisic acid (ABA) and polyethylene glycol (PEG) were added to successfully induce somatic embryos. Treatment with PEG and ABA was of great importance to somatic embryo formation and complemented each other's effect. ABA assisted embryo growth, whereas PEG facilitated the formation of proembryo-like structures. On top of this, we studied in more detail the relationship between redox homeostasis and the efficiency of somatic embryogenesis (frequency of ESM induction). During subculture, we observed the gradual formation of three distinct types of ESM. The Type I ESM is readily able to form somatic embryos. In contrast to type I, the type III ESM suffers from severe browning, contains a higher level of hydrogen peroxide (H2O2) and demonstrates a decreased ability to form somatic embryos. External treatment with H2O2 decreased the somatic embryogenesis efficiency of Type I and type III ESMs, or the higher the exogenous H2O2 content, the lower the resulting somatic embryogenesis efficiency. We found that treatment with the H2O2 scavenger DMTU (dimethylthiourea) could significantly increase the somatic embryogenesis efficiency of the type III ESM, as a result of a decline in endogenous H2O2 content. Overall, these findings have contributed to setting up a successful somatic embryogenesis system for larch production.

Steric-hindrance Effect Tuned Ion Solvation Enabling High Performance Aqueous Zinc Ion Batteries.

Despite many additives have been reported for aqueous zinc ion batteries, steric-hindrance effect of additives and its correlation with Zn2+ solvation structure have been rarely reported. Herein, large-sized sucrose biomolecule is selected as a paradigm additive, and steric-hindrance electrolytes (STEs) are developed to investigate the steric-hindrance effect for solvation structure regulation. Sucrose molecules do not participate in Zn2+ solvation shell, but significantly homogenize the distribution of solvated Zn2+ and enlarge Zn2+ solvation shell with weakened Zn2+-H2O interaction due to the steric-hindrance effect. More importantly, STEs afford the water-shielding electric double layer and in situ construct the organic and inorganic hybrid solid electrolyte interface, which effectively boost Zn anode reversibility. Remarkably, Zn//NVO battery presents high capacity of 3.9 mAh ⋅ cm-2 with long cycling stability for over 650 cycles at lean electrolyte of 4.5 µL ⋅ mg-1 and low N/P ratio of 1.5, and the stable operation at wide temperature (-20 °C~+40 °C).

A Semisolvated Sole-Solvent Electrolyte for High-Voltage Lithium Metal Batteries.

Lithium metal batteries (LMBs) coupled with a high-voltage Ni-rich cathode are promising for meeting the increasing demand for high energy density. However, aggressive electrode chemistry imposes ultimate requirements on the electrolytes used. Among the various optimized electrolytes investigated, localized high-concentration electrolytes (LHCEs) have excellent reversibility against a lithium metal anode. However, because they consist of thermally and electrochemically unstable solvents, they have inferior stability at elevated temperatures and high cutoff voltages. Here we report a semisolvated sole-solvent electrolyte to construct a typical LHCE solvation structure but with significantly improved stability using one bifunctional solvent. The designed electrolyte exhibits exceptional stability against both electrodes with suppressed lithium dendrite growth, phase transition, microcracking, and transition metal dissolution. A Li||Ni0.8Co0.1Mn0.1O2 cell with this electrolyte operates stably over a wide temperature range from -20 to 60 °C and has a high capacity retention of 95.6% after the 100th cycle at 4.7 V, and ∼80% of the initial capacity is retained even after 180 cycles. This new electrolyte indicates a new path toward future electrolyte engineering and safe high-voltage LMBs.

Comprehensive analysis of the UDP-glucuronate decarboxylase (UXS) gene family in tobacco and functional characterization of NtUXS16 in Golgi apparatus in Arabidopsis.

BACKGROUND: UDP-glucuronate decarboxylase (also named UXS) converts UDP-glucuronic acid (UDP-GlcA) to UDP-xylose (UDP-Xyl) by decarboxylation of the C6-carboxylic acid of glucuronic acid. UDP-Xyl is an important sugar donor that is required for the synthesis of plant cell wall polysaccharides. RESULTS: In this study, we first carried out the genome-wide identification of NtUXS genes in tobacco. A total of 17 NtUXS genes were identified, which could be divided into two groups (Group I and II), and the Group II UXSs can be further divided into two subgroups (Group IIa and IIb). Furthermore, the protein structures, intrachromosomal distributions and gene structures were thoroughly analyzed. To experimentally verify the subcellular localization of NtUXS16 protein, we transformed tobacco BY-2 cells with NtUXS16 fused to the monomeric red fluorescence protein (mRFP) at the C terminus under the control of the cauliflower mosaic virus (CaMV) 35S promoter. The fluorescent signals of NtUXS16-mRFP were localized to the medial-Golgi apparatus. Contrary to previous predictions, protease digestion analysis revealed that NtUXS16 is not a type II membrane protein. Overexpression of NtUXS16 in Arabidopsis seedling in darkness led to a significant increase in hypocotyl length and a reduction in root length compared with the wild type. In summary, these results suggest Golgi apparatus localized-NtUXS16 plays an important role in hypocotyl and root growth in the dark. CONCLUSION: Our findings facilitate our understanding of the novel functions of NtUXS16 and provide insights for further exploration of the biological roles of NtUXS genes in tobacco.

Clay-Originated Two-Dimensional Holey Silica Separator for Dendrite-Free Lithium Metal Anode.

Lithium metal anode is the ultimate choice to obtain next-generation high-energy-density lithium batteries, while the dendritic lithium growth owing to the unstable lithium anode/electrolyte interface largely limits its practical application. Separator is an important component in batteries and separator engineering is believed to be a tractable and effective way to address the above issue. Separators can play the role of ion redistributors to guide the transport of lithium ions and regulate the uniform electrodeposition of Li. The electrolyte wettability, thermal shrinkage resistance, and mechanical strength are of importance for separators. Here, clay-originated two-dimensional (2D) holey amorphous silica nanosheets (ASN) to develop a low-cost and eco-friendly inorganic separator is directly adopted. The ASN-based separator has higher porosity, better electrolyte wettability, much higher thermal resistance, larger lithium transference number, and ionic conductivity compared with commercial separator. The large amounts of holes and rich surface oxygen groups on the ASN guide the uniform distribution of lithium-ion flux. Consequently, the Li//Li cell with this separator shows stable lithium plating/stripping, and the corresponding Li//LiFePO4 , Li//LiCoO2, and Li//NCM523 full cells also show high capacity, excellent rate performance, and outstanding cycling stability, which is much superior to that using the commercial separator.

Evaluation of liver function using Gd-EOB-DTPA-enhanced MRI with T1 mapping.

PURPOSE: To evaluate the value of MRI T1 mapping with Gd-EOB-DTPA for assessing liver function. METHODS: Seventy-two patients who underwent Gd-EOB-DTPA-enhanced MRI for focal liver lesions at Beijing Friendship Hospital from August 2020 to March 2022 were prospectively enrolled, and variable-flip-angle T1 mapping was performed before and 20 min after enhancement. The Child-Pugh (C-P) score and albumin-bilirubin (ALBI) grade of liver function were assessed using the clinical data of the patients. Correlation analysis was used to evaluate the correlation between T1 mapping parameters and liver function grading and laboratory tests. Nonparametric tests were used to compare the differences among different liver function groups. The liver function classification efficiency of each image index was evaluated with receiver operating characteristic (ROC) curves. RESULTS: T1post was positively correlated with the C-P grade and the ALBI grade (r = 0.717 and r = 0.652). ΔT1 was negatively correlated with the C-P grade and the ALBI grade (r = -0.790 and r = -0.658). T1post and ΔT1 significantly differed among different liver function grades (p < 0.05). For the C-P grade, T1post and ΔT1 were significantly different between each pair of groups (p < 0.05), and ΔT1 had a better diagnostic efficiency than T1post. For the ALBI grade, ΔT1 and T1post were significantly different between the NLF and ALBI1 groups (p < 0.05), and ΔT1 had a better diagnostic efficacy than T1post. T1post significantly differed between the ALBI1 and ALBI2 + 3 groups (p < 0.05), while ΔT1 had a weak ability to differentiate between these two groups. CONCLUSION: T1post and ΔT1 were strongly correlated with the two liver function grades and can be noninvasive imaging indexes for evaluating liver function.

Stable Operation of Lithium Metal Batteries with Aggressive Cathode Chemistries at 4.9†V.

High-voltage lithium metal batteries (LMBs) pose severe challenges for the matching of electrolytes with aggressive electrodes, especially at low temperatures. Here, we report a rational modification of the Li+ solvation structure to extend the voltage and temperature operating ranges of conventional electrolytes. Ion-ion and ion-dipole interactions as well as the electrochemical window of solvents were tailored to improve oxidation stability and de-solvation kinetics of the electrolyte. Meanwhile, robust and elastic B and F-rich interphases are formed on both electrodes. Such optimization enables Li||LiNi0.5 Mn1.5 O4 cells (90.2 % retention after 400 cycles) and Li||LiNi0.6 Co0.2 Mn0.2 O2 (NCM622) cells (74.0 % retention after 200 cycles) to cycle stably at an ultra-high voltage of 4.9 V. Moreover, NCM622 cells deliver a considerable capacity of 143.5 mAh g-1 at -20 °C, showing great potential for practical uses. The proposed strategy sheds light on further optimization for high-voltage LMBs.

Low-chirp push-pull dual-ring modulator with 144 Gb/s PAM-4 data transmission.

We experimentally demonstrate a low-chirp high-speed push-pull dual-ring modulator. The device is formed by two parallel cascaded add-drop ring modulators which has a Fabry-Perot resonance spectrally similar as electromagnetically induced transparency (EIT) effect. Differential drive signals are applied to the two rings to shift the individual resonances towards opposite directions, creating intensity modulation with suppressed frequency chirp. We present static and dynamic characterization of the device, including chirp parameter. We also demonstrate 144 Gb/s PAM-4 data transmission with 1-km standard single-mode fiber (SSMF) with BER below hard-decision forward error correction (HD-FEC) threshold with 7% overhead.

Compact high-extinction tunable CROW filters for integrated quantum photonic circuits.

We describe the use of cascaded second-order coupled-resonator optical waveguide (CROW) tunable filters to achieve one of the highest reported measured extinction ratios of $ {\gt} {110}\;{\rm dB}$>110dB. The CROW filters were used to remove the pump photons in spontaneous four-wave mixing (SFWM) in a silicon waveguide. The SFWM generated quantum-correlated photons that could be measured after the cascaded CROW filters. The CROW filters offer a compact footprint for use in monolithic quantum photonic circuits.

A two-step mutation process in the double WS1 homologs drives the evolution of burley tobacco, a special chlorophyll-deficient mutant with abnormal chloroplast development.

MAIN CONCLUSION: The functional homologs WS1A and WS1B, identified by map-based cloning, control the burley character by affecting chloroplast development in tobacco, contributing to gene isolation and genetic improvement in polyploid crops. Burley represents a special type of tobacco (Nicotiana tabacum L.) cultivar that is characterized by a white stem with a high degree of chlorophyll deficiency. Although important progress in the research of burley tobacco has been made, the molecular mechanisms underlying this character remain unclear. Here, on the basis of our previous genetic analyses and preliminary mapping results, we isolated the White Stem 1A (WS1A) and WS1B genes using a map-based cloning approach. WS1A and WS1B are functional homologs with completely identical biological functions and highly similar expression patterns that control the burley character in tobacco. WS1A and WS1B are derived from Nicotiana sylvestris and Nicotiana tomentosiformis, the diploid ancestors of Nicotiana tabacum, respectively. The two genes encode zinc metalloproteases of the M50 family that are highly homologous to the Ethylene-dependent Gravitropism-deficient and Yellow-green 1 (EGY1) protein of Arabidopsis and the Lutescent 2 (L2) protein of tomato. Transmission electron microscopic examinations indicated that WS1A and WS1B are involved in the development of chloroplasts by controlling the formation of thylakoid membranes, very similar to that observed for EGY1 and L2. The genotyping of historical tobacco varieties revealed that a two-step mutation process occurred in WS1A and WS1B during the evolution of burley tobacco. We also discussed the strategy for gene map-based cloning in polyploid plants with complex genomes. This study will facilitate the identification of agronomically important genes in tobacco and other polyploid crops and provide insights into crop improvement via molecular approaches.

Multi-wavelength selective crossbar switch.

Here we demonstrate an 8x4 multi-wavelength selective ring resonator based crossbar switch matrix implemented in a 220-nm silicon photonics foundry for interconnecting electronic packet switches in scalable data centers. This switch design can dynamically assign up to two wavelength channels for any port-port connection, providing almost full connectivity with significant reduction in latency, cost and complexity. The switch unit cell insertion loss was measured at 0.8 dB, with an out-of-band rejection of 32 dB at 400 GHz channel separation. All the ring resonator heaters were thermally tuned, with heaters controlled by a custom 64-channel DAC driver. Detailed measurements on the whole switch showed standard deviation of 2 dB in losses across different paths, standard deviation of 0.33 nm in resonant wavelength and standard deviation of 0.01 nm/mW in ring heater tuning efficiency. Data transmission experiments at 40 Gbps showed negligible penalty due to crosstalk paths through the switch.

One-shot synthetic aperture digital holographic microscopy with non-coplanar angular-multiplexing and coherence gating.

This paper proposes one-shot synthetic aperture digital holographic microscopy using a combination of angular-multiplexing and coherence gating. The proposed angular-multiplexing technique uses multiple noncoplanar incident beams into the synthetic aperture to create tight packed passbands so as to extend spatial frequency spectrum. Coherence gating is performed to prevent the self-interference among the multiple beams. Based on the design guideline proposed herein, a phase-only spatial light modulator is employed as an adjustable blazed grating to split multiple noncoplanar beams and perform angular-multiplexing, and then using coherence gating based on low-coherence-light, superresolution imaging is achieved after one-shot acquisition.

Integrated germanium-on-silicon Franz-Keldysh vector modulator used with a Kramers-Kronig receiver.

We propose an integrated vector modulator based on two compact and high-speed germanium-on-silicon Franz-Keldysh electro-absorption modulators. The proposed vector modulator is extremely compact with a total footprint of only 1800 µm×200 µm. We further experimentally demonstrate a 4-quadrature-amplitude-modulation (4-QAM) at 40 Gb/s over a 20-km standard single-mode fiber transmission. The complex signal is successfully re-constructed with a single-ended photodiode in a recently proposed Kramers-Kronig receiver for future low-cost, low-power, and low-footprint datacenter interconnect applications. The preliminary performance of the vector modulator with a 16-QAM is also investigated.

Morphological phenotyping and genetic analyses of a new chemical-mutagenized population of tobacco (Nicotiana tabacum L.).

MAIN CONCLUSION: A novel tobacco mutant library was constructed, screened, and characterized as a crucial genetic resource for functional genomics and applied research. A comprehensive mutant library is a fundamental resource for investigating gene functions, especially after the completion of genome sequencing. A new tobacco mutant population induced by ethyl methane sulfonate mutagenesis was developed for functional genomics applications. We isolated 1607 mutant lines and 8610 mutant plants with altered morphological phenotypes from 5513 independent M2 families that consisted of 69,531 M2 plants. The 2196 mutations of abnormal phenotypes in the M2 putative mutants were classified into four groups with 17 major categories and 51 subcategories. More than 60% of the abnormal phenotypes observed fell within the five major categories including plant height, leaf shape, leaf surface, leaf color, and flowering time. The 465 M2 mutants exhibited multiple phenotypes, and 1054 of the 2196 mutations were pleiotropic. Verification of the phenotypes in advanced generations indicated that 70.63% of the M3 lines, 84.87% of the M4 lines, and 95.75% of the M5 lines could transmit original mutant phenotypes of the corresponding M2, M3, and M4 mutant plants. Along with the increased generation of mutants, the ratios of lines inheriting OMPs increased and lines with emerging novel mutant phenotypes decreased. Genetic analyses of 18 stably heritable mutants showed that two mutants were double recessive, five were monogenic recessive, eight presented monogenic dominant inheritance, and three presented semi-dominant inheritance. The pleiotropy pattern, saturability evaluation, research prospects of genome, and phenome of the mutant populations were also discussed. Simultaneously, this novel mutant library provided a fundamental resource for investigating gene functions in tobacco.

Fully suspended slot waveguides for high refractive index sensitivity.

A fully suspended mid-infrared (FSMIR) slot waveguide is proposed and experimentally demonstrated on a silicon-on-insulator (SOI) platform for the first time. The slotted waveguide core is mechanically supported by lateral subwavelength grating claddings. The fabricated waveguides possess low propagation loss, which is measured to be 7.9 dB/cm at the wavelength of 2.25 µm. With the underlying buried oxide (BOX) removed, the FSMIR slot waveguide has a broad spectral range of transparency that is limited only by the absorption of silicon. Numerical simulation shows that its sensitivity, defined as the ratio between the change of the effective index and the ambient refractive index, can reach 1.123, which is 9.7% higher than the maximal sensitivity of conventional SOI slot waveguides on BOX.

Genome-wide identification and expression analysis of the WRKY gene family in common tobacco (Nicotiana tabacum L.).

The coding products of WRKY gene family plays important roles in plant growth and development as well as in various stress responses. They have been identified in various plants, but only few in common tobacco (Nicotiana tabacum L.). In this study, 164 putative WRKY proteins in the common tobacco genome were identified by using the conserved WRKY sequence (PF03106) from the Pfam database. Phylogenetic trees, functional domain analysis, chromosomal localization, subcellular localization and tissue expression patterns were analyzed with the bioinformatics softwares, including DNAMAN 5.0, Weblogo 3, MEGA 5.1, MG2C and MEME. First of all, phylogenetic trees divided all the candidate genes into three subfamilies: Ⅰ, Ⅱ and Ⅲ, respectively, and subfamily Ⅱ could be further divided into five subgroups: group Ⅱ-a, -b, -c, -d and -e. Secondly, the WRKY regions contained a highly conserved heptapeptide stretch WRKYGQK followed by a zinc-finger motif. Most of the NtWRKY genes contained 2-5 exons and a highly conserved gene structure. Thirdly, 154 out of 164 NtWRKY genes were distributed with different densities on 24 chromosomes, and each subfamily with different patterns and frequency. The largest number of NtWRKY genes was found on chromosome VI, and only one on chromosome X. Fourthly, the majority of NtWRKY members located in the nucleus, with 74 percent of subfamily Ⅲ in the extracellular matrix. Lastly, the members in the same subfamily had different spatial and temporal expression profiles, with 11 NtWRKY genes in roots, stems and leaves expressed at various levels. The expression of genes NtWRKY26, NtWRKY30 and NtWRKY32 can be induced by Phytophthora nicotianae. Our research thus provides valuable information for NtWRKY gene cloning and functional characterization in common tobacco.