Metalens for Accelerated Optoelectronic Edge Detection under Ambient Illumination.

Analog systems may allow image processing, such as edge detection, with low computational power. However, most demonstrated analog systems, based on either conventional 4-f imaging systems or nanophotonic structures, rely on coherent laser sources for illumination, which significantly restricts their use in routine imaging tasks with ambient, incoherent illumination. Here, we demonstrated a metalens-assisted imaging system that can allow optoelectronic edge detection under ambient illumination conditions. The metalens was designed to generate polarization-dependent optical transfer functions (OTFs), resulting in a synthetic OTF with an isotropic high-pass frequency response after digital subtraction. We integrated the polarization-multiplexed metalens with a polarization camera and experimentally demonstrated single-shot edge detection of indoor and outdoor scenes, including a flying airplane, under ambient sunlight illumination. The proposed system showcased the potential of using polarization multiplexing for the construction of complex optical convolution kernels toward accelerated machine vision tasks such as object detection and classification under ambient illumination.

Metasurface-Based Solid Poincaré Sphere Polarizer.

The combination of conventional polarization optical elements, such as linear polarizers and waveplates, is widely adopted to tailor light's state of polarization (SOP). Meanwhile, less attention has been given to the manipulation of light's degree of polarization (DOP). Here, we propose metasurface-based polarizers that can filter unpolarized incident light to light with any prescribed SOP and DOP, corresponding to arbitrary points located both at the surface and within the solid Poincaré sphere. The Jones matrix elements of the metasurface are inverse-designed via the adjoint method. As prototypes, we experimentally demonstrated metasurface-based polarizers in near-infrared frequencies that can convert unpolarized light into linear, elliptical, or circular polarizations with varying DOPs of 1, 0.7, and 0.4, respectively. Our Letter unlocks a new degree of freedom for metasurface polarization optics and may break new ground for a variety of DOP-related applications, such as polarization calibration and quantum state tomography.

Integrated Terahertz Generator-Manipulators Using Epsilon-near-Zero-Hybrid Nonlinear Metasurfaces.

In terahertz (THz) technologies, generation and manipulation of THz waves are two key processes usually implemented by different device modules. Integrating THz generation and manipulation into a single compact device will advance the applications of THz technologies in various fields. Here, we demonstrate a hybrid nonlinear plasmonic metasurface incorporating an epsilon-near-zero (ENZ) indium tin oxide (ITO) layer to seamlessly combine efficient generation and manipulation of THz waves across a wide frequency band. The coupling between the plasmonic resonance of the metasurface and the ENZ mode of the ITO thin film enhances the THz conversion efficiency by more than 4 orders of magnitude. Meanwhile, such a hybrid device is capable of shaping the polarization and wavefront of the emitted THz beam via the engineered nonlinear Pancharatnam-Berry (PB) phases of the plasmonic meta-atoms. The presented hybrid nonlinear metasurface opens a new avenue toward miniaturized integrated THz devices and systems with advanced functionalities.

Manipulation of quantum dot emission with semiconductor metasurfaces exhibiting magnetic quadrupole resonances.

Optical metasurfaces were suggested as a route for engineering advanced light sources with tailored emission properties. In particular, they provide a control over the emission directionality, which is essential for single-photon sources and LED applications. Here, we experimentally study light emission from a metasurface composed of III-V semiconductor Mie-resonant nanocylinders with integrated quantum dots (QDs). Specifically, we focus on the manipulation of the directionality of spontaneous emission from the QDs due to excitation of different magnetic quadrupole resonances in the nanocylinders. To this end, we perform both back focal plane imaging and momentum-resolved spectroscopy measurements of the emission. This allows for a comprehensive analysis of the effect of the different resonant nanocylinder modes on the emission characteristics of the metasurface. Our results show that the emission directionality can be manipulated by an interplay of the excited quadrupolar nanocylinder modes with the metasurface lattice modes and provide important insights for the design of novel smart light sources and new display concepts.

Near-field nonlinear imaging of an anapole mode beyond diffraction limit.

Nonlinear nanophotonics, as an emerging field in nanophotonics, eagerly calls for experimental techniques for probing and analyzing near-field nonlinear optical signals with subwavelength resolution. Here, we report an aperture-type scanning near-field optical microscopic method for probing near-field nonlinear optical processes. As a demonstration, near-field third-harmonic generation from an anapole dark-mode state generated by a silicon nanodisk is probed and imaged. The measured results agree well with the simulations, with a spatial resolution down to $0.14{\lambda _0}$ and a sensitivity of 0.1 nW. This method provides a powerful tool for characterizing nonlinear light-matter interactions at the nanoscale, which can help, for example, to unveil crystal properties involving subwavelength defects or dislocations.

Metasurface for Structured Light Projection over 120° Field of View.

Structured light projection is a widely adopted approach for depth perception in consumer electronics and other machine vision systems. Diffractive optical element (DOE) is a key component for structured light projection that redistributes a collimated laser beam to a spot array with uniform intensity. Conventional DOEs for laser spot projection are binary-phase gratings, suffering from low efficiency and low uniformity when designed for a large field of view (FOV). Here, by combining vectorial electromagnetic simulation and interior-point method for optimization, we experimentally demonstrate polarization-independent silicon-based metasurfaces that can project a collimated laser beam to a spot array in the far-field with an exceedingly large FOV over 120° × 120°. The metasurface DOE with large FOV may benefit a number of depth perception-related applications such as face-unlock and motion sensing.

High-contrast optical switching using an epsilon-near-zero material coupled to a Bragg microcavity.

Epsilon-near-zero (ENZ) materials have recently been suggested as excellent candidates for constructing all-optical and electro-optical switches in the infrared. The performance of previously reported ENZ material-based optical switches, however, has been greatly hampered by the low quality- (Q-) factor of the ENZ cavity, resulting in a large required optical pump fluence or applied voltage, a large insertion loss, or a small modulation depth. Here, we propose a solution by integrating the ENZ material into a Bragg microcavity, such that the Q-factor of the coupled cavity can be dramatically enhanced. Using high-mobility Dysprosium-doped cadmium oxide (CdO) as the prototype ENZ material, we numerically show an infrared all-optical switch with its reflectance modulated from near-zero to 94% under a pump fluence of only 7 µJ cm-2, about a 59-time-reduction compared with a state-of-the-art Berreman-type cavity. Moreover, the high-Q coupled cavity can also be adopted to realize a reflective electro-optical switch. Its reflectance can be switched from near-zero to 89%, with a bias electric field well below the breakdown field of conventional gate dielectrics. The switching operation can further be extended to the transmission mode with a slightly modified cavity geometry, with its absolute transmittance modulated by 40%.

Terahertz Driven Amplification of Coherent Optical Phonons in GaAs Coupled to a Metasurface.

We demonstrate amplification of longitudinal optical (LO) phonons by polar-optical interaction with an electron plasma in a GaAs structure coupled to a metallic metasurface using two-color two-dimensional spectroscopy. In a novel scheme, the metamaterial resonator enhances broadband terahertz fields, which generate coherent LO phonons and drive free electrons in the conduction band of GaAs. The time evolution of the LO phonon amplitude is monitored with midinfrared pulses via the LO-phonon-induced Kerr nonlinearity of the sample, showing an amplification of the LO phonon amplitude by up to a factor of 10, in agreement with a theoretical estimate.

Light-Emitting Metasurfaces: Simultaneous Control of Spontaneous Emission and Far-Field Radiation.

Light-emitting sources and devices permeate every aspect of our lives and are used in lighting, communications, transportation, computing, and medicine. Advances in multifunctional and "smart lighting" would require revolutionary concepts in the control of emission spectra and directionality. Such control might be possible with new schemes and regimes of light-matter interaction paired with developments in light-emitting materials. Here we show that all-dielectric metasurfaces made from III-V semiconductors with embedded emitters have the potential to provide revolutionary lighting concepts and devices, with new functionality that goes far beyond what is available in existing technologies. Specifically, we use Mie-resonant metasurfaces made from semiconductor heterostructures containing epitaxial quantum dots. By controlling the symmetry of the resonant modes, their overlap with the emission spectra, and other structural parameters, we can enhance the brightness by 2 orders of magnitude, as well as reduce its far-field divergence significantly.

Resonantly Enhanced Second-Harmonic Generation Using III-V Semiconductor All-Dielectric Metasurfaces.

Nonlinear optical phenomena in nanostructured materials have been challenging our perceptions of nonlinear optical processes that have been explored since the invention of lasers. For example, the ability to control optical field confinement, enhancement, and scattering almost independently allows nonlinear frequency conversion efficiencies to be enhanced by many orders of magnitude compared to bulk materials. Also, the subwavelength length scale renders phase matching issues irrelevant. Compared with plasmonic nanostructures, dielectric resonator metamaterials show great promise for enhanced nonlinear optical processes due to their larger mode volumes. Here, we present, for the first time, resonantly enhanced second-harmonic generation (SHG) using gallium arsenide (GaAs) based dielectric metasurfaces. Using arrays of cylindrical resonators we observe SHG enhancement factors as large as 10(4) relative to unpatterned GaAs. At the magnetic dipole resonance, we measure an absolute nonlinear conversion efficiency of ∼2 × 10(-5) with ∼3.4 GW/cm(2) pump intensity. The polarization properties of the SHG reveal that both bulk and surface nonlinearities play important roles in the observed nonlinear process.

Hot Electron-Based Near-Infrared Photodetection Using Bilayer MoS2.

Recently, there has been much interest in the extraction of hot electrons generated from surface plasmon decay, as this process can be used to achieve additional bandwidth for both photodetectors and photovoltaics. Hot electrons are typically injected into semiconductors over a Schottky barrier between the metal and semiconductor, enabling generation of photocurrent with below bandgap photon illumination. As a two-dimensional semiconductor single and few layer molybdenum disulfide (MoS2) has been demonstrated to exhibit internal photogain and therefore becomes an attractive hot electron acceptor. Here, we investigate hot electron-based photodetection in a device consisting of bilayer MoS2 integrated with a plasmonic antenna array. We demonstrate sub-bandgap photocurrent originating from the injection of hot electrons into MoS2 as well as photoamplification that yields a photogain of 10(5). The large photogain results in a photoresponsivity of 5.2 A/W at 1070 nm, which is far above similar silicon-based hot electron photodetectors in which no photoamplification is present. This technique is expected to have potential use in future ultracompact near-infrared photodetection and optical memory devices.

Nonlinear Fano-Resonant Dielectric Metasurfaces.

Strong nonlinear light-matter interaction is highly sought-after for a variety of applications including lasing and all-optical light modulation. Recently, resonant plasmonic structures have been considered promising candidates for enhancing nonlinear optical processes due to their ability to greatly enhance the optical near-field; however, their small mode volumes prevent the inherently large nonlinear susceptibility of the metal from being efficiently exploited. Here, we present an alternative approach that utilizes a Fano-resonant silicon metasurface. The metasurface results in strong near-field enhancement within the volume of the silicon resonator while minimizing two photon absorption. We measure a third harmonic generation enhancement factor of 1.5 × 10(5) with respect to an unpatterned silicon film and an absolute conversion efficiency of 1.2 × 10(-6) with a peak pump intensity of 3.2 GW cm(-2). The enhanced nonlinearity, combined with a sharp linear transmittance spectrum, results in transmission modulation with a modulation depth of 36%. The modulation mechanism is studied by pump-probe experiments.

Dielectric meta-reflectarray for broadband linear polarization conversion and optical vortex generation.

Plasmonic metasurfaces have recently attracted much attention due to their ability to abruptly change the phase of light, allowing subwavelength optical elements for polarization and wavefront control. However, most previously demonstrated metasurface designs suffer from low coupling efficiency and are based on metallic resonators, leading to ohmic loss. Here, we present an alternative approach to plasmonic metasurfaces by replacing the metallic resonators with high-refractive-index silicon cut-wires in combination with a silver ground plane. We experimentally demonstrate that this meta-reflectarray can be used to realize linear polarization conversion with more than 98% conversion efficiency over a 200 nm bandwidth in the short-wavelength infrared band. We also demonstrate optical vortex beam generation using a meta-reflectarray with an azimuthally varied phase profile. The vortex beam generation is shown to have high efficiency over a wavelength range from 1500 to 1600 nm. The use of dielectric resonators in place of their plasmonic counterparts could pave the way for ultraefficient metasurface-based devices at high frequencies.

Metasurface array for single-shot spectroscopic ellipsometry.

Spectroscopic ellipsometry is a potent method that is widely adopted for the measurement of thin film thickness and refractive index. Most conventional ellipsometers utilize mechanically rotating polarizers and grating-based spectrometers for spectropolarimetric detection. Here, we demonstrated a compact metasurface array-based spectroscopic ellipsometry system that allows single-shot spectropolarimetric detection and accurate determination of thin film properties without any mechanical movement. The silicon-based metasurface array with a highly anisotropic and diverse spectral response is combined with iterative optimization to reconstruct the full Stokes polarization spectrum of the light reflected by the thin film with high fidelity. Subsequently, the film thickness and refractive index can be determined by fitting the measurement results to a proper material model with high accuracy. Our approach opens up a new pathway towards a compact and robust spectroscopic ellipsometry system for the high throughput measurement of thin film properties.

Single-shot deterministic complex amplitude imaging with a single-layer metalens.

Conventional imaging systems can only capture light intensity. Meanwhile, the lost phase information may be critical for a variety of applications such as label-free microscopy and optical metrology. Existing phase retrieval techniques typically require a bulky setup, multiframe measurements, or prior information of the target scene. Here, we proposed an extremely compact system for complex amplitude imaging, leveraging the extreme versatility of a single-layer metalens to generate spatially multiplexed and polarization phase-shifted point spread functions. Combining the metalens with a polarization camera, the system can simultaneously record four polarization shearing interference patterns along both in-plane directions, thus allowing the deterministic reconstruction of the complex amplitude light field in a single shot. Using an incoherent light-emitting diode as the illumination, we experimentally demonstrated speckle-noise-free complex amplitude imaging for both static and moving objects with tailored magnification ratio and field of view. The miniaturized and robust system may open the door for complex amplitude imaging in portable devices for point-of-care applications.

Metasurface designed with quantitative field distributions.

A new method for designing metasurfaces has been proposed and demonstrated, which allows for the generation of precise quantitative field distributions. This unique approach involves combining a tandem neural network with an iterative algorithm to optimize the metasurface design, enabling accurate control over the intensity and polarization of the resulting field. This strategy is both efficient and robust and has the potential to accelerate the development of metasurface devices with complex functionalities.

Monocular metasurface camera for passive single-shot 4D imaging.

It is a grand challenge for an imaging system to simultaneously obtain multi-dimensional light field information, such as depth and polarization, of a scene for the accurate perception of the physical world. However, such a task would conventionally require bulky optical components, time-domain multiplexing, and active laser illumination. Here, we experimentally demonstrate a compact monocular camera equipped with a single-layer metalens that can capture a 4D image, including 2D all-in-focus intensity, depth, and polarization of a target scene in a single shot under ambient illumination conditions. The metalens is optimized to have a conjugate pair of polarization-decoupled rotating single-helix point-spread functions that are strongly dependent on the depth of the target object. Combined with a straightforward, physically interpretable image retrieval algorithm, the camera can simultaneously perform high-accuracy depth sensing and high-fidelity polarization imaging over an extended depth of field for both static and dynamic scenes in both indoor and outdoor environments. Such a compact multi-dimensional imaging system could enable new applications in diverse areas ranging from machine vision to microscopy.

Efficient second- and higher-order harmonic generation from LiNbO3 metasurfaces.

Lithium niobate (LiNbO3) is a material that has drawn great interest in nonlinear optics because of its large nonlinear susceptibility and wide transparency window. However, for complex nonlinear processes such as high-harmonic generation (HHG), which involves frequency conversion over a wide frequency range, it can be extremely challenging for a bulk LiNbO3 crystal to fulfill the phase-matching conditions. LiNbO3 metasurfaces with resonantly enhanced nonlinear light-matter interaction at the nanoscale may circumvent such an issue. Here, we experimentally demonstrate efficient second-harmonic generation (SHG) and HHG from a LiNbO3 metasurface enhanced by guided-mode resonance. We observe a high normalized SHG efficiency of 5.1 × 10-5 cm2 GW-1. Moreover, with the alleviated above-gap absorption of the material, we demonstrate HHG up to the 7th order with the shortest generated wavelength of 226 nm. This work may provide a pathway towards compact coherent white-light sources with frequency spanning into the deep ultraviolet region for applications in spectroscopy and imaging.

Non-Invasive and Minute-Frequency 3D Tomographic Imaging Enabling Long-Term Spatiotemporal Observation of Single Cell Fate.

Non-invasive and rapid imaging technique at subcellular resolution is significantly important for multiple biological applications such as cell fate study. Label-free refractive-index (RI)-based 3D tomographic imaging constitutes an excellent candidate for 3D imaging of cellular structures, but its full potential in long-term spatiotemporal cell fate observation is locked due to the lack of an efficient integrated system. Here, a long-term 3D RI imaging system incorporating a cutting-edge white light diffraction phase microscopy module with spatiotemporal stability, and an acoustofluidic device to roll and culture single cells in a customized live cell culture chamber is reported. Using this system, 3D RI imaging experiments are conducted for 250 cells and demonstrate efficient cell identification with high accuracy. Importantly, long-term and frequency-on-demand 3D RI imaging of K562 and MCF-7 cancer cells reveal different characteristics during normal cell growth, drug-induced cell apoptosis, and necrosis of drug-treated cells. Overall, it is believed that the proposed 3D tomographic imaging technique opens up a new avenue for visualizing intracellular structures and will find many applications such as disease diagnosis and nanomedicine.

Highly Tunable Cascaded Metasurfaces for Continuous Two-Dimensional Beam Steering.

Cascaded metasurfaces can exhibit powerful dynamic light manipulation by mechanically tuning the far-field interactions in the layers. However, in most current designs, the metasurfaces are separated by gaps smaller than a wavelength to form a total phase profile, representing the direct accumulation of the phase profiles of each layer. Such small gap sizes may not only conflict with the far-field conditions but also pose great difficulties for practical implementations. To overcome this limitation, a design paradigm taking advantage of a ray-tracing scheme that allows the cascaded metasurfaces to operate optimally at easily achievable gap sizes is proposed. Enabled by the relative lateral translation of two cascaded metasurfaces, a continuous two-dimensional (2D) beam-steering device for 1064 nm light is designed as a proof of concept. Simulation results demonstrate tuning ranges of ±45° for biaxial deflection angles within ±3.5 mm biaxial translations, while keeping the divergence of deflected light less than 0.007°. The experimental results agree well with theoretical predictions, and a uniform optical efficiency is observed. The  generializeddesign paradigm can pave a way towards myriad tunable cascaded metasurface devices for various applications, including but not limited to light detection and ranging (LiDAR) and free space optical communication.