RESUMEN
OBJECTIVE: To investigate the antibacterial effect of different self-etching adhesive systems against Streptococcus mutans (S. mutans). METHODS: Six reagents Clearfil(TM) SE Bond primer (SP), Clearfil(TM) SE Bond adhesive (SA),Clearfil(TM) Protect Bond primer (PP), which contained antibacterial monomer methacryloyloxydodecylpyridinium bromide (MDPB), ClearfilTM Protect Bond adhesive (PA), positive control chlorhexidine acetate [CHX, 1% (mass fraction)], and negative control phosphate buffer solution (PBS) were selected. They were mixed with S. mutans for 30 s respectively, then colony-forming units (CFU) were counted after incubated for 48 h on brain heart infusion (BHI) agar medium. The 6 reagents were applied to the sterile paper discs, and distributed onto the BHI agar medium with S. mutans and incubated for 24 h, then the inhibition zones were observed. CHX, PBS, PP, and SP were added on the dentin with artificial caries induced by S. mutans and kept for 30 s, then confocal laser scanning microscope (CLSM) was used to observe the live and dead bacteria after staining. The ratio of live to dead bacteria was calculated. PP+PA and SP+SA were applied on the dentin according to the manual and light cured. S. mutans were incubated on the samples for 2 h, ultrasonically treated and incubated on BHI agar medium for 48 h, then CFU was counted. The data were analyzed by non-parametric analysis and one-way ANOVA. RESULTS: Compared with PBS, the PP, SP, PA, SA and CHX showed the antibacterial effect on free S. mutans (P<0.05); SP and PP showed stronger antibacterial effect than PA, SA and CHX (P<0.05). CHX, SP and PP presented inhibition zones, while PBS, SA and PA did not. Compared with PBS, the CHX, SP and PP could lower the ratio of the live to dead bacteria significantly (P<0.05). Cured self-etching adhesive systems did not show any antibacterial effect on the free S. mutans. CONCLUSION: The primer of self-etching adhesives Clearfil(TM) SE Bond and Clearfil(TM) Protect Bond showed significant antibacterial effect on free and attached S. mutans. The adhesive only showed antibacterial effect on free S. mutans before light-cured polymerization. After being cured, the self-etching adhesive systems did not show antibacterial effect anymore.
Asunto(s)
Adhesivos/química , Antibacterianos/farmacología , Grabado Dental , Recubrimientos Dentinarios/química , Streptococcus mutans/efectos de los fármacos , Caries Dental , Dentina/química , Humanos , Compuestos de Piridinio/farmacologíaRESUMEN
OBJECTIVE: To identify Streptococcus mutans (S. mutans) in carious patients' saliva using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), and to establish a faster and more accurate method to identify S. mutans. METHODS: In this study, a total of 90 carious patients from Department of Endodontics of Peking University School of Stomatology were recruited. All these patients' saliva was collected. After extracting the protein of the samples, they were identified by MALDI-TOF MS. The composite profile was analyzed using BioExplorer 1.0 software. The scores ≥ 25 were considered as S. mutans, whereas the scores <25 were as considered as non S. mutans. Finally, these results were compared with 16S rDNA sequencing to figure out the sensitivity and concordance rate, respectively. RESULTS: The sensitivity of MALDI-TOF MS was 96.0%, and the concordance rate compared with 16S rDNA sequencing was as high as 98.7%. CONCLUSION: MALDI-TOF MS is high throughput, rapid and easy to perform in comparison to other conventional methods. It has a high sensivity and concordance rate. Thus, MALDI-TOF MS can serve as an effective tool for identification of S. mutans.
Asunto(s)
Caries Dental/microbiología , Saliva/microbiología , Espectrometría de Masa por Láser de Matriz Asistida de Ionización Desorción , Streptococcus mutans/aislamiento & purificación , HumanosRESUMEN
Background/purpose: Root canal filling is a necessary skill for dental students and an important aspect of endodontic education. This study aimed to evaluate the effect of students' clinical experiences on isthmus filling using different techniques and sealers. Materials and methods: One hundred eight three-dimensional-printed resin replicas of isthmus were divided into six groups and either continuous wave of condensation (CWC) or single-cone obturation (SC) was performed. One of three sealers (AH Plus Jet®, GuttaFlow2, iRoot SP) was used together with a size-fitted gutta-percha master cone. All the obturations were completed by students with three different levels of clinical experience including senior postgraduate students (SPS), junior postgraduate students (JPS), and undergraduate students (US). The percentages of filled areas (PFA) at 2, 4, 6, and 8 mm from the apex were analyzed using a light microscope. Data were analyzed using the Mann-Whitney U test or Kruskal-Wallis 1-way ANOVA with Dunn's tests (α = 0.05). Results: The CWC group exhibited a higher PFA than the SC group (P < 0.05). The PFA was higher in the SPS group than in the JPS group or the US group with CWC (P < 0.05). The three clinical experience groups showed similar PFAs with SC (P > 0.05); however, when using SC with iRoot SP, the PFA was higher than with either of the other two sealers (P < 0.05). Conclusion: CWC was found to be technique-sensitive and required clinical training. With SC, clinical experience did not improve the quality of isthmus filling without additional training. CWC was superior to SC for type IV isthmuses. When using SC, better filling quality was obtained with a bioceramic sealer.
RESUMEN
Background/purpose: Effective filling of the lateral canals is of great significance in successful root canal treatment, but it is generally being challenging. This study aimed to evaluate the influence of relative positions of the heat carrier and lateral canal opening on gutta-percha obturation of lateral canals in a three-dimensional (3D)-printed model. Materials and methods: Thermal conductivity and real-time temperature transmission of gutta-percha were investigated using laser flash and thermal infrared analyses. 3D-printed root canal models with lateral canals at 1, 3, and 5 mm from the apex were fabricated, and different relative positions of the heat carrier were tested. The obturation process was recorded on video, and the obturation depth of the lateral canals was observed using X-ray micro-computed tomography. Results: Gutta-percha showed low thermal conductivity of 1.07 W/(m·K), and heating increased the temperature of gutta-percha above 60 °C only within 1 mm beyond the heat carrier tip. For lateral canals at 1 and 3 mm from the apex, gutta-percha penetrated further with deeper penetration of the heat carrier (P < 0.05). For 5-mm lateral canals, the heat carrier was always at apical level and the gutta-percha obturation depth was more at 2 mm apically than at 3 or 4 mm (P < 0.05). Conclusion: Gutta-percha is a poor thermal conductor. The position of the heat carrier in relation to the lateral canal opening affects obturation depth. Only when the heat carrier reaches or passes the lateral canal opening can gutta-percha penetrate a lateral canal.