RESUMEN
Lithium-sulfur (Li-S) batteries are highly regarded as the next-generation energy-storage devices because of their ultrahigh theoretical energy density of 2600â Wh kg-1 . Sulfurized polyacrylonitrile (SPAN) is considered a promising sulfur cathode to substitute carbon/sulfur (C/S) composites to afford higher Coulombic efficiency, improved cycling stability, and potential high-energy-density Li-SPAN batteries. However, the instability of the Li-metal anode threatens the performances of Li-SPAN batteries bringing limited lifespan and safety hazards. Li-metal can react with most kinds of electrolyte to generate a protective solid electrolyte interphase (SEI), electrolyte regulation is a widely accepted strategy to protect Li-metal anodes in rechargeable batteries. Herein, the basic principles and current challenges of Li-SPAN batteries are addressed. Recent advances on electrolyte regulation towards stable Li-metal anodes in Li-SPAN batteries are summarized to suggest design strategies of solvents, lithium salts, additives, and gel electrolyte. Finally, prospects for future electrolyte design and Li anode protection in Li-SPAN batteries are discussed.
RESUMEN
MAIN CONCLUSION: Six types of lignin-carbohydrate complex (LCC) fractions were isolated from Eucalyptus. The acidic dioxane treatment applied significantly improved the yield of LCCs. The extraction conditions had a limited impact on the LCC structures and linkages. Characterization of the lignin-carbohydrate complex (LCC) structures and linkages promises to offer insight on plant cell wall chemistry. In this case, Eucalyptus LCCs were extracted by aqueous dioxane, and then precipitated sequentially by 70% ethanol, 100% ethanol, and acidic water (pH = 2). The composition and structure of the six LCC fractions obtained by selective precipitation were investigated by sugar analysis, molecular weight determination, and 2D HSQC NMR. It was found that the acidic (0.05-M HCl) dioxane treatment significantly improved the yield of LCCs (66.4% based on Klason lignin), which was higher than the neutral aqueous dioxane extraction, and the extraction condition showed limited impact on the LCC structures and linkages. In the fractionation process, the low-molecular-weight LCCs containing a high content of carbohydrates (60.3-63.2%) were first precipitated by 70% ethanol from the extractable solution. The phenyl glycoside (PhGlc) bonds (13.0-17.0 per 100Ar) and highly acetylated xylans were observed in the fractions recovered by the precipitation with 100% ethanol. On the other hand, such xylan-rich LCCs exhibited the highest frequency of ß-O-4 linkages. The benzyl ether (BE) bonds were only detected in the fractions obtained by acidic water precipitation.
Asunto(s)
Carbohidratos/aislamiento & purificación , Eucalyptus/metabolismo , Lignina/aislamiento & purificación , Metabolismo de los Hidratos de Carbono , Carbohidratos/química , Precipitación Química , Dioxanos/uso terapéutico , Lignina/química , Lignina/metabolismo , Espectroscopía de Resonancia Magnética , Peso MolecularRESUMEN
Blending poly (butylene adipate-co-terephthalate) (PBAT) and polylactic acid (PLA) is a cost-effective strategy to obtain biodegradable plastic with complementary properties. However, the incompatibility between PBAT and PLA is a great challenge for fabricating high-performance composite films. Herein, the ethyl acetate fractionated lignin with the small glass transition temperature and low molecular weight was achieved and incorporated into the PBAT/PLA composite as a compatibilizer. The fractionated lignin can be uniformly dispersed within the PBAT/PLA matrix through a melt blending process and interact with the molecular chain of PBAT and PLA as a bonding bridge, which enhances the intermolecular interactions and reduces the interfacial tension of PBAT/PLA. By adding fractionated lignin, the tensile strength of the PBAT/PLA composite increased by 35.4 % and the yield strength increased by 37.7 %. Owing to lignin, the composite films possessed the ultraviolet shielding function and exhibited better water vapor barrier properties (1.73 ± 0.08 × 10-13 g·cm/cm2·s·Pa). This work conclusively demonstrated that fractionated lignin can be used as a green compatibilizer and a low-cost functional filler for PBAT/PLA materials, and provides guidance for the application of lignin in biodegradable plastics.
Asunto(s)
Alquenos , Plásticos Biodegradables , Lignina , Ácidos Ftálicos , Adipatos , Poli A , PoliésteresRESUMEN
In recent years, nanocellulose (NC) has gained significant attention due to its remarkable properties, such as adjustable surface chemistry, extraordinary biological properties, low toxicity and low density. This review summarizes the preparation of NC derived from lignocellulosic biomass (LCB), including cellulose nanofibrils (CNF), cellulose nanocrystals (CNC), and lignin-containing cellulose nanofibrils (LCNF). It focuses on examining the impact of non-cellulosic components such as lignin and hemicellulose on the functionality of NC. Additionally, various surface modification strategies of NC were discussed, including esterification, etherification and silylation. The review also emphasizes the progress of NC application in areas such as Pickering emulsions, food packaging materials, food additives, and hydrogels. Finally, the prospects for producing NC from LCB and its application in food-related fields are examined. This work aims to demonstrate the effective benefits of preparing NC from lignocellulosic biomass and its potential application in the food industry.
RESUMEN
The practical applications of lithium-sulfur (Li-S) batteries have severely been hindered by notorious shuttle effect and sluggish redox kinetics of lithium polysulfide intermediates (LiPSs), which bring about rapid capacity degradation, low coulombic efficiency and poor cycling stability. In this work, 1T-rich MoS2 nanosheets are in-situ developed onto the conductive porous carbon matrix (1T-rich MoS2@PC) as efficient polysulfide promotors for high-performance Li-S batteries. The porous carbon skeleton tightly anchors MoS2 nanosheets to prevent their reaggregation and ensures accessible electrical channels, and at the same time provides a favorable confined space that promotes the generation of 1T-rich MoS2 structure. More importantly, the uniformly distributed metallic 1T-rich MoS2 nanosheets not only affords rich sulfphilic sites and high binding energy for immobilizing LiPSs, but also favors rapid electron transfer and LiPSs conversation kinetics, substantially regulating sulfur chemistry in working cells. Consequently, the Li-S cell assembled with 1T-rich MoS2@PC modified separator delivers a remarkable cycling stability with ultralow capacity decay rate of 0.067% over 500 cycles at 1C. Encouragingly, under harsh conditions (high sulfur loading of 4.78 mg cm-2 and low E/S ratio of 8 µL mg-1), a favorable electrochemical performance can still be demonstrated. This study highlights the profitable design of 1T-rich MoS2/carbon based electrocatalyst for suppressing shuttle effect and promoting catalytic conversation of LiPSs, and has the potential to be applied to in other energy storage systems.
RESUMEN
Utilizing renewable lignocellulosic resources for wastewater remediation is crucial to achieving sustainable social development. However, the resulting by-products and the synthetic process characterized by complexity, high cost, and environmental pollution limit the further development of lignocellulose-based materials. Here, we developed a sustainable strategy that involved a new functional deep eutectic solvent (DES) to deconstruct industrial xylose residue into cellulose-rich residue with carboxyl groups, lignin with carboxyl and quaternary ammonium salt groups, and DES effluent rich in lignin fragments. Subsequently, these fractions equipped with customized functionality were used to produce efficient wastewater remediation materials in cost-effective and environmentally sound manners, namely, photocatalyst prepared by carboxyl-modified cellulose residue, biochar-based adsorbent originated from modified lignin, and flocculant synthesized by self-catalytic in situ copolymerization of residual DES effluent at room temperature. Under the no-waste principle, this strategy upgraded the whole components of waste lignocellulose into high-value-added wastewater remediation materials with excellent universality. These materials in coordination with each other can stepwise purify high-hazardous mineral processing wastewater into drinkable water, including the removal of 99.81% of suspended solids, almost all various heavy metal ions, and 97.09% chemical oxygen demand, respectively. This work provided promising solutions and blueprints for lignocellulosic resources to alleviate water shortages while also advancing the global goal of carbon neutrality.
RESUMEN
Although the effects of cellulose crystallinity and lignin content as two major structural features on enzymatic hydrolysis have been extensively studied, debates regarding their effects still exist. In this study, reconstitution of cellulose and lignin after 1-ethyl-3-methylimidazolium acetate ([C(2)mim][OAc]) pretreatment was proposed as a new method to study their effects on enzymatic digestibility. Different mechanisms of lignin content for reduction of cellulose hydrolysis were found between the proposed method and the traditional method (mixing of cellulose and lignin). The results indicated that a slight change of the crystallinity of the reconstituted materials may play a minor role in the change of enzyme efficiency. In addition, the present study suggested that the lignin content does not significantly affect the digestibility of cellulose, whereas the conversion of cellulose fibers from the cellulose I to the cellulose II crystal phase plays an important role when an ionic liquid pretreatment of biomass was conducted.
Asunto(s)
Celulasas/antagonistas & inhibidores , Celulasas/metabolismo , Celulosa/metabolismo , Inhibidores Enzimáticos/metabolismo , Imidazoles/química , Líquidos Iónicos/química , Lignina/metabolismo , HidrólisisRESUMEN
Fungal treatment followed by FeCl3 treatment was used to improve saccharification of wood from Populus tomentosa. Combined treatments accumulated lignin and slightly degraded cellulose, whereas almost all hemicelluloses were removed. The white rot fungus, Trametes orientalis, and the brown rot fungus, Fomitopsis palustris, both accompanied by FeCl3 post-treatment resulted in 98.8 and 99.7 % of hemicelluloses loss at 180 °C, respectively, which were over twice than that of hot water pretreatment at the same level. In addition, the solid residue from the T. orientalis-assisted and F. palustris-assisted FeCl3 treatment at 180 °C released 84.5 and 95.4 % of reducing sugars, respectively: 1.4- and 1.6-fold higher than that of FeCl3 treatment alone at the same temperature. Combined treatments disrupted the intact cell structure and increased accessible surface area of cellulose therefore enhancing the enzymatic digestibility, as evidenced by XRD and SEM analysis data.
Asunto(s)
Carbohidratos/química , Cloruros/química , Coriolaceae/metabolismo , Compuestos Férricos/química , Hidrólisis , Madera/química , Madera/metabolismo , Populus , Madera/microbiologíaRESUMEN
To comprehend the biosynthesis processes of conifers, it is essential to investigate the disparity between the cell wall shape and the interior chemical structures of polymers throughout the development of Chinese pine. In this study, branches of mature Chinese pine were separated according to their growth time (2, 4, 6, 8 and 10 years). The variation of cell wall morphology and lignin distribution was comprehensively monitored by scanning electron microscopy (SEM) and confocal Raman microscopy (CRM), respectively. Moreover, the chemical structures of lignin and alkali-extracted hemicelluloses were extensively characterized by nuclear magnetic resonance (NMR) and gel permeation chromatography (GPC). The thickness of latewood cell walls increased steadily from 1.29 µm to 3.38 µm, and the structure of the cell wall components became more complicated as the growth time increased. Based on the structural analysis, it was found that the content of ß-O-4 (39.88-45.44/100 Ar), ß-ß (3.20-10.02/100 Ar) and ß-5 (8.09-15.35/100 Ar) linkages as well as the degree of polymerization of lignin increased with the growth time. The complication propensity increased significantly over 6 years before slowing to a trickle over 8 and 10 years. Furthermore, alkali-extracted hemicelluloses of Chinese pine mainly consist of galactoglucomannans and arabinoglucuronxylan, in which the relative content of galactoglucomannans increased with the growth of the pine, especially from 6 to 10 years.
Asunto(s)
Pared Celular , Lignina , Pinus , Polisacáridos , Lignina/química , Pinus/química , Pinus/crecimiento & desarrollo , Polisacáridos/química , Pared Celular/química , Pared Celular/metabolismoRESUMEN
Phytoremediation with energy crops is considered an integrated technology that provides both environment and energy benefits. Herein, the sweet sorghum cultivated on Cd-contaminated farmland (1.21 mg/kg of Cd in the soil) showed promising phytoremediation potential, and the approach for utilizing sorghum stalks was explored. Sweet sorghum bagasse with Cd contamination was pretreated with dilute acid in order to improve enzymatic saccharification and achieve Cd recovery, resulting in harmless and value-added utilization. After pretreatment, hemicelluloses were dramatically degraded, and the lignocellulosic structures were partially deconstructed with xylan removal up to 98.1%. Under the optimal condition (0.75% H2SO4), the highest total sugar yield was 0.48 g/g of raw bagasse; and nearly 98% of Cd was enriched in the liquid phase. Compared with normal biomass, Cd reduced the biomass recalcitrance and further facilitated the deconstruction of biomass under super dilute acid conditions. This work provided an example for the subsequent valorization of Cd-containing biomass and Cd recovery, which will greatly facilitate the development of phytoremediation of heavy metal contaminated soil.
Asunto(s)
Cadmio , Sorghum , Cadmio/metabolismo , Sorghum/química , Biodegradación Ambiental , Hidrólisis , Suelo , BiomasaRESUMEN
Deep eutectic solvents (DESs) have emerged as promising and eco-friendly solvents for the efficient extraction of lignin from biomass due to their low cost and environmental benefits. Nevertheless, the prevalent use of acidic DESs in lignin extraction often results in excessive depolymerization and recondensation of lignin, thereby impeding its downstream applications. In this study, we developed a range of alkaline DESs (ADESs), both pure and peroxide-containing, for the extraction of high-quality lignin from bamboo. Moreover, carbon dioxide (CO2) was employed for the precipitation and regeneration of the extracted lignin. The obtained lignin fractions were comprehensively characterized in terms of yield, purity, morphology, solubility, structural features, and anti-UV/oxidant activity. The results showed that the monoethanolamine-based ADES demonstrated superior performance among the pure ADESs. Structural analysis confirmed the well-preserved substructures of lignin fractions obtained using ADESs, with ß-O-4 bond retention ranging from 49.8 % to 68.4 %. The incorporation of a suitable amount of peroxide improved lignin yield, morphology, solubility, and anti-UV/oxidant activity. Additionally, the anti-UV/oxidant activity of lignin exhibited a positive correlation with its phenolic hydroxyl content. This study provides a valuable reference for the green and sustainable production and valorization of lignin within the existing biorefinery framework.
Asunto(s)
Disolventes Eutécticos Profundos , Lignina , Lignina/química , Solventes/química , Antioxidantes , Biomasa , Oxidantes , HidrólisisRESUMEN
In this study, light-colored lignin was extracted from bamboo shoot shells (BSS) using a hydrated deep eutectic solvent (DES) pretreatment. The hydrated DES used in pretreatment consist of formic acid, benzyl triethylammonium chloride (BTEAC) and water. The pretreatment using a hydrated DES containing 30% water (H30) demonstrate efficient delignification (82.9%). Additionally, the hydrated DES protected the ß-O-4 linkage from excessive cleavage and recondensation as well as keep the light-colored of lignin. Moreover, the hydrated DES extracted lignin exhibits superior antioxidant performance and tyrosinase inhibitory capacity compared to the control. Notably, incorporating 5% lignin of H30-extracted lignin into a commercial suncream led to a remarkable enhancement of the SPF value, elevating from 14.8 to 32.6. In summary, the proposed hydrated DES pretreatment method offers significant benefits for extracting light-colored lignin, thereby promoting the multifunctional application of lignin in cosmetics.
Asunto(s)
Disolventes Eutécticos Profundos , Lignina , Solventes , Biomasa , Agua , HidrólisisRESUMEN
In this work, a green and robust pretreatment which integrated acetic acid-catalyzed hydrothermal and wet mechanical pretreatment, was developed to efficiently produce high yield (up to 40.12%) of xylooligosaccharides and digestible substrates from Caffeoyl Shikimate Esterase down-regulated and control poplar wood. Subsequently, superhigh yield (more than 95%) of glucose and residual lignin were obtained after a moderate enzymatic hydrolysis. The residual lignin fraction exhibited a well-preserved ß-O-4 linkages (42.06/100Ar) and high S/G ratio (6.42). Subsequently, lignin-derived porous carbon was successfully synthesized, and it exhibited a high specific capacitance of 273.8 F g-1 at 1.0 A g-1 and long cycling stability (remained 98.5% after 10,000 cycles at 5.0 A g-1) compared to control poplar wood, demonstrating that special advantage of this genetically-modified poplar in this integrated process. This work developed an energy-saving and eco-friendly pretreatment technology as a waste-free route for converting different lignocellulosic biomass to multiple products.
Asunto(s)
Esterasas , Lignina , Hidrólisis , MaderaRESUMEN
Effective separation of lignin macromolecules from the xylose pre-hydrolysates (XPH) during the xylose production, thus optimizing the separation and purification process of xylose, is of great significance for reducing the production costs, achieving the high value-added utilization of lignin and increasing the industrial revenue. In this study, a simple and robust method (pH adjustment) for the separation of lignin from XPH was proposed and systematically compared with the conventional acid-promoted lignin precipitation method. The results showed that the lignin removal ratio (up to 60.34 %) of this simple method was higher than that of the conventional method, and the proposed method eliminated the necessity of heating and specialized equipment, which greatly reduced the separation cost. Meanwhile, this simple method does not destroy the components in XPH (especially xylose), ensuring the yield of the target product. On the other hand, the obtained lignin was nano-scale with less condensed structures, which also possessed small molecular weights with narrow distribution, excellent antioxidant activity (8-14 times higher than commercial antioxidants) and UV protection properties. In conclusion, the proposed simple separation method could effectively separate lignin from XPH at low cost, and the obtained lignin had potential commercial applications, which would further enhance the overall profitability of industrial production.
Asunto(s)
Lignina , Xilosa , Lignina/química , Xilosa/química , Hidrólisis , Bebidas AlcohólicasRESUMEN
Utilizing starch, an abundant polysaccharide, as the renewable filler to blend with poly(butylene adipate-co-terephthalate) (PBAT) is a feasible tactic to construct cost-effective and high-performance biodegradable materials. It's worth noting that the thermal processing properties of starch can be manipulated by its plasticized behavior. Herein, epoxidized soybean oil (ESO) and glycerol were used as the plasticizer for native corn starch and the plasticized starch was integrated with PBAT to manufacture starch-based biodegradable blend films. ESO breaks the hydrogen bonds between starch chains through the fatty chains grafting reaction and increases the distance between starch molecular chains due to the large molecular weight of ESO. Meanwhile, glycerol molecules are incorporated into the starch molecular chains, and fatty chains grafted starch chains, effectively reducing the intermolecular forces of molecular chains. On account of the synergistic plasticization of ESO and glycerol which possess good compatibility with PBAT, the PSG20E10 blend film achieved a tensile strength, an elongation at break of 16.11 MPa and 612.09 %, and the balanced water and oxygen permeability properties.
Asunto(s)
Glicerol , Poliésteres , Poliésteres/química , Almidón/química , AdipatosRESUMEN
In this work, a rapid one-pot hydrated deep eutectic solvent (DES) pretreatment was proposed to facilitate the conversion of carbohydrates from lignocellulosic biomass to monosaccharides. Specifically, the pure and hydrated DES based on benzyl triethylammonium chloride (BTEAC), formic acid (FA) and water was used to pretreat bamboo shoot shells (BSS) by microwave heating. The pretreated solid residues were enzymatically saccharified to produce fermentable sugars, and the hydrolyzed carbohydrates and lignin remained in the hydrolyzate. The results showed that the yield of monosaccharides from the hydrated DES hydrolyzate (193.7-228.4 g/kg) was significantly higher than that (45.9-66.1 g/kg) of pure DES. The 30% hydrated DES pretreatment achieved the best glucose yield (89.03%) and a total monosaccharides yield of 555.4 g/kg, which corresponded to a conversion ratio of carbohydrates to monosaccharides of 87.0%. The proposed process is a robust method for the efficiently convert carbohydrates from BSS into monosaccharides.
Asunto(s)
Carbohidratos , Disolventes Eutécticos Profundos , Lignina/química , Glucosa/química , Monosacáridos , Hidrólisis , Biomasa , Solventes/químicaRESUMEN
Deep eutectic solvents (DESs) have unique advantages in biomass conversion. However, the migration and transformation mechanism of lignin in the cell wall during the DES pretreatment is still elusive. In this work, Eucalyptus blocks were pretreated in choline chloride/lactic acid DES to reveal the lignin migration. Meanwhile, the remaining lignin in the pretreated residue, the regenerated DES lignin, and the solubilized degraded lignin in the recovered DES were investigated to decipher the lignin transformation. Results showed that the DES pretreatment resulted in the penetration of DES from the cell lumen to the cell wall, and lignin in the secondary wall was more easily dissolved than that in the cell corner middle lamella. The syringyl unit of lignin was better stabilized in the DES than the guaiacyl unit of lignin. The condensed lignin fraction mainly remained in the pretreated residue, while the solubilized degraded lignin fraction was monomeric aromatic ketone compounds. This study elucidates the fate of lignin during the DES pretreatment, which could also promote the development of a modern lignocellulosic pretreatment technique.
Asunto(s)
Eucalyptus , Lignina , Biomasa , Disolventes Eutécticos Profundos , Hidrólisis , Lignina/química , Solventes/químicaRESUMEN
Complex and heterogeneous structures of lignin impede its further conversion and valorization. Herein, three technical lignins (from softwood, hardwood, and grass) were fractionated with acetone solvent to reduce their structural heterogeneity, which were then blended with poly-(butylene adipate-co-terephthalate) (PBAT) to fabricate biodegradable bio-composites. Macromolecular structures of lignins and their effects on the properties of lignin/PBAT composites were thoroughly investigated. Results showed that all fractionated lignin composites displayed better properties. Particularly, the raw and fractionated softwood lignin-based composites exhibited superior performance compared with others. Benefiting from the lower molecular weight, hydroxyl groups, and condensation, acetone fractionated softwood lignin presented the lowest Tg (115.7 °C), achieving ideal melt miscibility and interfacial interaction between lignin and PBAT. The decreased Tg of lignin facilitated the lignin dispersion in the matrix and increase the mechanical strength of the composites. Overall, the fractionated technical lignin possessed desirable physical and chemical structure features, conferring composites good miscibility and mechanical properties.
Asunto(s)
Lignina , Poliésteres , Acetona , Adipatos , Alquenos , Lignina/química , Ácidos Ftálicos , Poliésteres/químicaRESUMEN
Developing a biorefinery process for a highly integrated valorization and fractionation of lignocellulose is crucial for its utilization. Herein, a biphasic system comprising choline chloride/lactic acid and 2-methyltetrahydrofuran with Al2(SO4)3 and H2SO4 as catalysts was applied to pretreat Eucalyptus. Results showed that under the optimized conditions (150 °C, 30 min, 0.2 M Al2(SO4)3, 0.075 M H2SO4), the furfural yield and enzymatic hydrolysis efficiency could reach 54.7% and 97.0%, respectively. The efficient cellulose conversion was attributed to remarkable removal of lignin (91.0%) and hemicelluloses (100.0%), thereby causing the disruption of cell wall structure and enhancement of cellulose accessibility. Meanwhile, confocal Raman microscope and atomic force microscope displayed that the pretreatment resulted in the decreasing intensities of carbohydrates and lignin different regions of cell walls, and exposing of the embedded microfibers from noncellulosic polymers. Overall, the deep eutectic solvent-based biphasic system displayed high performance for effective utilization of carbohydrate components in lignocellulose.
Asunto(s)
Furaldehído , Lignina , Biomasa , Carbohidratos , Celulosa , Disolventes Eutécticos Profundos , Hidrólisis , Lignina/química , SolventesRESUMEN
An aspirational pretreatment method for efficient fractionation and tailored valorization of large industrial biomass can ensure the realizability of sustainable biorefinery strategies. In this study, an ultrafast alkaline deep eutectic solvents (DES) pretreatment strategy was developed to efficiently extract the lignin nanoparticles and retain cellulose residues that could be readily enzymatic saccharified to obtain fermentative glucose for the bioenergy production from industrial xylose residue. Results showed that the DES pretreatment had excellent delignification performance and the regenerated DES lignin nanoparticles exhibited well-preserved structures and excellent antioxidant activity, as well as low molecular weights and relatively uniform size distribution, which could facilitate downstream catalytic degradation for production of chemicals and preparation of lignin-based materials. Under the optimal condition (DES pretreatment: 80 °C, 10 min; saccharification: 10 FPU/g, 5 wt%, 100 mg/g Tween 80), the glucose yield of 90.12% could be achieved, which was dramatically increased compared to raw materials.