Selective Scatterings of Phonons and Electrons in Defective Half-Heusler Nb1- δ CoSb for the Figure of Merit zT > 1.

The recently developed defective 19-electron half-Heusler (HH) compounds, represented by Nb1- δ CoSb, possess massive intrinsic vacancies at the cation site and thus intrinsically low lattice thermal conductivity that is desirable for thermoelectric (TE) applications. Yet the TE performance of defective HHs with a maximum figure of merit (zT) <1.0 is still inferior to that of the conventional 18-electron ones. Here, a peak zT exceeding unity is obtained at 1123 K for both Nb0.7 Ta0.13 CoSb and Nb0.6 Ta0.23 CoSb, a benchmark value for defective 19-electron HHs. The improved zT results from the achievement of selective scatterings of phonons and electrons in defective Nb0.83 CoSb, using lanthanide contraction as a design factor to select alloying elements that can strongly impede the phonon propagation but weakly disturb the periodic potential. Despite the massive vacancies induced strong point defect scattering of phonons in Nb0.83 CoSb, Ta alloying is still found effective in suppressing lattice thermal conductivity while maintaining the carrier mobility almost unchanged. In comparison, V alloying significantly deteriorates the carrier transport and thus the TE performance. These results enlarge the category of high-performance HH TE materials beyond the conventional 18-electron ones and highlight the effectiveness of selective scatterings of phonons and electrons in developing TE materials even with massive vacancies.

A Novel Perovskite Electron-Ion Conductive Coating to Simultaneously Enhance Cycling Stability and Rate Capability of Li1.2 Ni0.13 Co0.13 Mn0.54 O2 Cathode Material for Lithium-Ion Batteries.

Poor cycling stability and rate capability are two key issues needing to be solved for Li- and Mn-rich oxide cathode material for lithium-ion batteries (LIBs). Herein, a novel perovskite electron-ion mixed conductor Nd0.6 Sr0.4 CoO3 (NSCO) is used as the coating layer on Li1.2 Ni0.13 Co0.13 Mn0.54 O2 (LNCMO) to simultaneously enhance its cycling stability and rate capability. By coating 3 wt% NSCO, LNCMO-3NSCO exhibits an optimal cycling performance with a capacity retention of 99% at 0.1C (1C = 200 mA g-1 ) after 60 cycles, 91% at 1C after 300 cycles, and 54% at 20C after 1000 cycles, much better than 78%, 63%, and 3% of LNCMO, respectively. Even at a high charge and discharge rate of 50C, LNCMO-3NSCO exhibits a discharge capacity of 53 mAh g-1 and a mid-point discharge voltage of 2.88 V, much higher than those of LNCMO (24 mA h g-1 and 2.40 V, respectively). Benefiting from the high electronic conductivity (1.46 S cm-1 ) and ionic conductivity (1.48 × 10-7  S cm-1 ), NSCO coating not only suppresses transition metals dissolution and structure transformation, but also significantly enhances electronic conductivity and Li+ diffusion coefficient of LNCMO by an order of magnitude.

Hybrid Organic-Inorganic Thermoelectric Materials and Devices.

Hybrid organic-inorganic materials have been considered as a new candidate in the field of thermoelectric materials since the last decade owing to their great potential to enhance the thermoelectric performance by utilizing the low thermal conductivity of organic materials and the high Seebeck coefficient, and high electrical conductivity of inorganic materials. Herein, we provide an overview of interfacial engineering in the synthesis of various organic-inorganic thermoelectric hybrid materials, along with the dimensional design for tuning their thermoelectric properties. Interfacial effects are examined in terms of nanostructures, physical properties, and chemical doping between the inorganic and organic components. Several key factors which dictate the thermoelectric efficiency and performance of various electronic devices are also discussed, such as the thermal conductivity, electric transportation, electronic band structures, and band convergence of the hybrid materials.

Synthesis and thermoelectric properties of Rashba semiconductor BiTeBr with intensive texture.

Bismuth tellurohalides with Rashba-type spin splitting exhibit unique Fermi surface topology and are developed as promising thermoelectric materials. However, BiTeBr, which belongs to this class of materials, is rarely investigated in terms of the thermoelectric transport properties. In the study, polycrystalline bulk BiTeBr with intensive texture was synthesized via spark plasma sintering (SPS). Additionally, its thermoelectric properties above room temperature were investigated along both the in-plane and out-plane directions, and they exhibit strong anisotropy. Low sound velocity along two directions is found and contributes to its low lattice thermal conductivity. Polycrystalline BiTeBr exhibits relatively good thermoelectric performance along the in-plane direction, with a maximum dimensionless figure of merit (ZT) of 0.35 at 560 K. Further enhancements of ZT are expected by utilizing systematic optimization strategies.

A14MgBi11 (A = Ca, Sr, Eu): Magnesium Bismuth Based Zintl Phases as Potential Thermoelectric Materials.

A series of new magnesium bismuth Zintl phases, A14MgBi11 (A = Ca, Sr, Eu), have been synthesized, and their thermoelectric properties were systematically evaluated. These novel phases belong to the well-known Yb14MnSb11 family, whose structure adopts the tetragonal space group I41/acd (No. 142) with cell parameters of a = 17.0470(17)/17.854(2)/17.6660(7) Å and c = 22.665(5)/23.580(6)/23.2446(18) Å for Ca14MgBi11, Sr14MgBi11, and Eu14MgBi11, respectively. Without intentional optimization, these materials exhibit high potential as new thermoelectric candidates. Especially for Sr14MgBi11, a high zT value of 0.72 has been approached at 1073 K. The discovery of these new Zintl series is very interesting, which implies the high possibility of extending the 14-1-11 thermoelectric system to the bismuth analogues in the development of highly efficient thermoelectric materials. Density functional theory (DFT) calculations were incorporated as well to help better understand the properties of these important compounds.

Structure, Magnetism, and Thermoelectric Properties of Magnesium-Containing Antimonide Zintl Phases Sr14MgSb11 and Eu14MgSb11.

New Mg-containing antimonide Zintl phases, Sr14MgSb11 and Eu14MgSb11, were synthesized from high-temperature solid-state reactions in Ta tubes at 1323 K. Their structures can be viewed as derived from the Ca14AlSb11 structure type, which adopt the tetragonal space group I41/acd (No. 142, Z = 8) with the cell parameters of a = 17.5691(14)/17.3442(11) Å and c = 23.399(4)/22.981(3) Å for the Sr- and Eu-containing compounds, respectively. The corresponding thermoelectric properties were probed, which demonstrated high potential of these compounds as new thermoelectrics for their very low thermal conductivity and moderate Seebeck coefficient. Magnetism studies and theoretical calculations were conducted as well to better understand the structure-and-property correlation of these materials.

Multiple Converged Conduction Bands in K2Bi8Se13: A Promising Thermoelectric Material with Extremely Low Thermal Conductivity.

We report that K2Bi8Se13 exhibits multiple conduction bands that lie close in energy and can be activated through doping, leading to a highly enhanced Seebeck coefficient and a high power factor with elevated temperature. Meanwhile, the large unit cell, complex low symmetry crystal structure, and nondirectional bonding lead to the very low lattice thermal conductivity of K2Bi8Se13, ranging between 0.42 and 0.20 W m-1 K-1 in the temperature interval 300-873 K. Experimentally, we further support the low thermal conductivity of K2Bi8Se13 using phonon velocity measurements; the results show a low average phonon velocity (1605 ms-1), small Young's modulus (37.1 GPa), large Grüneisen parameter (1.71), and low Debye temperature (154 K). A detailed investigation of the microstructure and defects was carried out using electron diffraction and transmission microscopy which reveal the presence of a K2.5Bi8.5Se14 minor phase intergrown along the side of the K2Bi8Se13 phase. The combination of enhanced power factor and low thermal conductivity results in a high ZT value of ∼1.3 at 873 K in electron doped K2Bi8Se13 material.

Reduced graphene oxide-induced recrystallization of NiS nanorods to nanosheets and the improved Na-storage properties.

Preparation of two-dimensional (2D) graphene-like materials is currently an emerging field in materials science since the discovery of single-atom-thick graphene prepared by mechanical cleavage. In this work, we proposed a new method to prepare 2D NiS, where reduced graphene oxide (rGO) was found to induce the recrystallization of NiS from nanorods to nanosheets in a hydrothermal process. The process and mechanism of recrystallization have been clarified by various characterization techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) mapping, and X-ray photoelectron spectroscopy (XPS). The characterization of ex situ NiS/rGO products by SEM and EDS mapping indicates that the recrystallization of NiS from nanorods to nanosheets is realized actually through an exfoliation process, while the characterization of in situ NiS/rGO products by SEM, TEM, and EDS mapping reveals the exfoliation process. The XPS result demonstrates that hydrothermally assisted chemical bonding occurs between NiS and rGO, which induces the exfoliation of NiS nanorods into nanosheets. The obtained NiS/rGO composite shows promising Na-storage properties.

Research on immersive interaction design based on visual and tactile feature analysis of visually impaired children.

To propose improved and innovative visual-tactile interaction design for visually impaired children, multi-modal combination approaches have been applied, such as voice interaction, touch interaction, and multi-modal systems, what's more, aided cognitive approaches help them deepen their understanding of objects, improve their cognitive level, and increase their interest. METHODS: To improve the amount of information in the visual-haptic interface by integrating multiple sensory information, based on the cognitive patterns of visually impaired children, a questionnaire was used to design a tactile-visual UI for the main content objects of visually impaired children when using the Internet, from which difficulties and problems in the design of visual-haptic for visually impaired children were found, and design improvements were proposed based on the principles and methods of accessible design. RESULTS: The personalized and humanized design activities enhance the confidence and improve the quality of life of the visually impaired children group and produce positive effects, improving the cognitive clarity of visually impaired children while increasing their level of understanding, imagination, learning interest and aesthetic experience. CONCLUSION: The physical and mental characteristics and visual and tactile characteristics of visually impaired children are analyzed, and the application of UI interaction design is based on these characteristics. The essence of interaction design is outlined through experiments, and it is found that with the development of the Internet, big data and artificial intelligence, visually impaired children have many difficulties in the use of the Internet, and through the improved practice of immersive interaction design, the humanized design approach is used to enhance visually impaired children's experience of using network interfaces. Through the improved practice of immersive interaction design, we improve the way of visually impaired children using the Internet, narrow the gap between them and normal children in the interaction, and give humanistic care.

Passive Self-Sustained Thermoelectric Devices Powering the 24 h Wireless Transmission via Radiation-Cooling and Selective Photothermal Conversion.

The rapid development of the Internet of Things has triggered a huge demand for self-sustained technology that can provide a continuous electricity supply for low-power electronics. Here, a self-sustained power supply solution is demonstrated that can produce a 24 h continuous and unipolar electricity output based on thermoelectric devices by harvesting the environmental temperature difference, which is ingeniously established utilizing radiation cooling and selective photothermal conversion. The developed prototype system can stably maintain a large temperature difference of about 1.8 K for a full day despite the real-time changes in environmental temperature and solar radiation, thereby driving continuous electricity output using the built-in thermoelectric device. Specifically, the large output voltage of >102 mV and the power density of >4.4 mW m-2 could be achieved for a full day, which are outstanding among the 24 h self-sustained thermoelectric devices and far higher than the start-up values of the wireless temperature sensor and also the light-emitting diode, enabling the 24 h remote data transmission and lighting, respectively. This work highlights the application prospects of self-sustained thermoelectric devices for low-power electronics.

High performance magnesium-based plastic semiconductors for flexible thermoelectrics.

Low-cost thermoelectric materials with simultaneous high performance and superior plasticity at room temperature are urgently demanded due to the lack of ever-lasting power supply for flexible electronics. However, the inherent brittleness in conventional thermoelectric semiconductors and the inferior thermoelectric performance in plastic organics/inorganics severely limit such applications. Here, we report low-cost inorganic polycrystalline Mg3Sb0.5Bi1.498Te0.002, which demonstrates a remarkable combination of large strain (~ 43%) and high figure of merit zT (~ 0.72) at room temperature, surpassing both brittle Bi2(Te,Se)3 (strain ≤ 5%) and plastic Ag2(Te,Se,S) and organics (zT ≤ 0.4). By revealing the inherent high plasticity in Mg3Sb2 and Mg3Bi2, capable of sustaining over 30% compressive strain in polycrystalline form, and the remarkable deformability of single-crystalline Mg3Bi2 under bending, cutting, and twisting, we optimize the Bi contents in Mg3Sb2-xBix (x = 0 to 1) to simultaneously boost its room-temperature thermoelectric performance and plasticity. The exceptional plasticity of Mg3Sb2-xBix is further revealed to be brought by the presence of a dense dislocation network and the persistent Mg-Sb/Bi bonds during slipping. Leveraging its high plasticity and strength, polycrystalline Mg3Sb2-xBix can be easily processed into micro-scale dimensions. As a result, we successfully fabricate both in-plane and out-of-plane flexible Mg3Sb2-xBix thermoelectric modules, demonstrating promising power density. The inherent remarkable plasticity and high thermoelectric performance of Mg3Sb2-xBix hold the potential for significant advancements in flexible electronics and also inspire further exploration of plastic inorganic semiconductors.

Research on mobile learning platform interface design based on college students' visual attention characteristics.

To explore the visual experience characteristics and influencing factors of college students' visual attention intervention in the interface of mobile learning platform by using eye-tracking technology, and to summarize and summarize the visual experience pattern of platform interface design and its design inspiration. METHODS: Using the head-mounted eye-tracking technology, 28 images from 6 groups of typical elements in the interface layout of CGTN learning platform were selected as the test samples, and the eye-movement indexes of the subjects browsing the interface were recorded. RESULTS: There were significant differences in the attention time, number of times of attention, visual attention rate and visual recall rate of different areas and topics of the interface (P < 0. 001). CONCLUSION: In the platform interface design, the analysis of the factors influencing visual attention can be found that people's attention and visual experience is mainly influenced by color, text, and typography, and secondary areas and layout also play an important role in visual communication. The color and text areas in the interface design, as well as the innovative design of typography can effectively enhance the visual attention of college students and better communicate the information of the platform.

An Elastic Cross-Linked Binder for Silicon Anodes in Lithium-Ion Batteries with a High Mass Loading.

Due to the urgent demand for lithium-ion batteries (LIBs) with a high energy density, silicon (Si) possessing an ultrahigh capacity has aroused wide attention. However, its practical application is seriously hindered by enormous volume changes of the Si anode during cycling. Developing novel binders suitable for the Si anode has proven to be an effective strategy to improve its electrochemical performance. Herein, we constructed a three-dimensional network binder, in which the polyacrylic acid (PAA) long chains are cross-linked with one kind of amino acid, lysine (Lys). The abundant polar groups in PAA/Lys enable it to tightly adhere to the Si particles via hydrogen bonds, and the cross-linked structure prevents irreversible slipping of the PAA chains upon volume variation of the particles. The Si used was obtained from a sustainable route by recycling photovoltaic waste silicon. With high elasticity and strong adhesion, the PAA/Lys binder can effectively keep the structural integrity of the Si electrode and improve its electrochemical performance. The Si electrode using the PAA/Lys binder exhibits a good cycling stability (1008 mAh g-1 at 2 A g-1 after 250 cycles). Even with a high mass loading of 3.03 mg cm-2, the Si anode can remain stable for 100 cycles at a high fixed areal capacity of 3.03 mAh cm-2. This work gives a practical method to make stable Si electrodes using sustainable Si source and environmentally friendly amino acid-based binders.

High-Performance Stretchable Thermoelectric Generator for Self-Powered Wearable Electronics.

Wearable thermoelectric generators (TEGs), which can convert human body heat to electricity, provide a promising solution for self-powered wearable electronics. However, their power densities still need to be improved aiming at broad practical applications. Here, a stretchable TEG that achieves comfortable wearability and outstanding output performance simultaneously is reported. When worn on the forehead at an ambient temperature of 15 °C, the stretchable TEG exhibits excellent power densities with a maximum value of 13.8 µW cm-2 under the breezeless condition, and even as high as 71.8 µW cm-2 at an air speed of 2 m s-1 , being one of the highest values for wearable TEGs. Furthermore, this study demonstrates that this stretchable TEG can effectively power a commercial light-emitting diode and stably drive an electrocardiogram module in real-time without the assistance of any additional power supply. These results highlight the great potential of these stretchable TEGs for power generation applications.

Opening the Bandgap of Metallic Half-Heuslers via the Introduction of d-d Orbital Interactions.

Half-Heusler compounds with semiconducting behavior have been developed as high-performance thermoelectric materials for power generation. Many half-Heusler compounds also exhibit metallic behavior without a bandgap and thus inferior thermoelectric performance. Here, taking metallic half-Heusler MgNiSb as an example, a bandgap opening strategy is proposed by introducing the d-d orbital interactions, which enables the opening of the bandgap and the improvement of the thermoelectric performance. The width of the bandgap can be engineered by tuning the strength of the d-d orbital interactions. The conduction type and the carrier density can also be modulated in the Mg1- x Tix NiSb system. Both improved n-type and p-type thermoelectric properties are realized, which are much higher than that of the metallic MgNiSb. The proposed bandgap opening strategy can be employed to design and develop new half-Heusler semiconductors for functional and energy applications.

Achieving metal-like malleability and ductility in Ag2Te1-x S x inorganic thermoelectric semiconductors with high mobility.

Inorganic semiconductor Ag2Te1-x S x has been recently found to exhibit unexpected plastic deformation with compressive strain up to 30%. However, the origin of the abnormal plasticity and how to simultaneously achieve superb ductility and high mobility are still elusive. Here, we demonstrate that crystalline/amorphous Ag2Te1-x S x (x = 0.3, 0.4, and 0.5) composites can exhibit excellent compressive strain up to 70% if the monoclinic Ag2Te phase, which commonly exists in the matrix, is eliminated. Significantly, an ultra-high tensile elongation reaching 107.3% was found in Ag2Te0.7S0.3, which is the highest one yet reported in the system and even surpasses those achieved in some metals and high-entropy alloys. Moreover, high mobility of above 1000 cm2 V-1 s-1 at room temperature and good thermoelectric performance are simultaneously maintained. A modified Ashby plot with ductility factor versus carrier mobility is thereby proposed to highlight the potential of solid materials for applications in flexible/wearable electronics.

High-Power-Density Wearable Thermoelectric Generators for Human Body Heat Harvesting.

Wearable thermoelectrics has attracted significant interest in recent years. Among them, rigid-structure thermoelectric generators (TEGs) were seldomly employed for wearable applications, although those exhibit significant advantages of high device output performance and impact resistance. Here, we report a type of rigid wearable TEGs (w-TEGs) without ceramic substrates made using a simple cutting-and-bonding method. Owing to the small contact area, the w-TEGs comprising 48-n/p-pairs can be well attached to the human body. The lack of ceramic substrates leaves more space in the height direction, which benefits the wearability in practical applications and high power density. We demonstrated that increasing the height of w-TEGs from 1.38 to 3.14 mm significantly improves the power density by a factor of 10. As a result, the maximum power densities of 7.9 µW cm-2 and 43.6 µW cm-2 for the w-TEGs were realized under the breezeless condition and a wind speed for normal walking, respectively. This work provides a feasible design solution for rigid-structure free-substrate w-TEGs with very high power density, which will speed up the research of wearable thermoelectrics.

Simultaneous Realization of Flexibility and Ultrahigh Normalized Power Density in a Heatsink-Free Thermoelectric Generator via Fine Thermal Regulation.

Wearable thermoelectric generators (w-TEGs) can incessantly convert body heat into electricity to power electronics. However, the low efficiency of thermoelectric materials, tiny terminal temperature difference, rigidity, and negligence of lateral heat transfer preclude broad utilization of w-TEGs. In this work, we employ finite element simulation to find the key factors for simultaneous realization of flexibility and ultrahigh normalized power density. Using melamine foam with an ultralow thermal conductivity (0.03 W/m K) as the encapsulation material, a novel lightweight π-type w-TEG with no heatsink and excellent stretchability, comfortability, processability, and cost efficiency has been fabricated. At an ambient temperature of 24 °C, the maximum power density of the w-TEG reached 7 µW/cm2 (sitting) and 29 µW/cm2 (walking). Under suitable heat exchange conditions (heatsink with 1 m/s air velocity), 32 pairs of w-TEGs can generate 66 mV voltage and 60 µW/cm2 power density. The output performance of our TEG is remarkably superior to that of previously reported w-TEGs. Besides, the practicality of our w-TEG was showcased by successfully driving a quartz watch at room temperature.

Mo-Fe/NbFeSb Thermoelectric Junctions: Anti-Thermal Aging Interface and Low Contact Resistivity.

In recent years, high-performance half-Heusler compounds have been developed as promising thermoelectric materials for power generation. Aiming at practical device applications, one key step is to seek suitable metal electrodes so that low interfacial resistivity is guaranteed under long-term thermal aging. In the previous work, the fresh Mo/Nb0.8Ti0.2FeSb junction was found exhibiting low contact resistivity below 1 µΩ cm2; however, it increased by tens of times under long-term thermal aging, mainly originating from the formation of the high-resistivity FeSb2 phase and the appearance of cracks. Here, the Mo-Fe electrodes are employed to build the junctions with Nb0.8Ti0.2FeSb. The interfacial behavior and contact resistance in these junctions were investigated both before and after the thermal aging. Interestingly, no obvious formation of FeSb2 phase and cracks were observed. As a result, the contact resistivity was below ∼1 µΩ cm2 after 15 days' thermal aging, indicating better connection reliability and lower contact resistivity compared to the Mo/Nb0.8Ti0.2FeSb junction. These findings highlight the applicability of Mo-Fe electrodes and pave the way for NbFeSb-based half-Heusler thermoelectric materials for device applications.

Tuneable local order in thermoelectric crystals.

Although crystalline solids are characterized by their periodic structures, some are only periodic on average and deviate on a local scale. Such disordered crystals with distinct local structures have unique properties arising from both collective and localized behaviour. Different local orderings can exist with identical average structures, making their differences hidden to Bragg diffraction methods. Using high-quality single-crystal X-ray diffuse scattering the local order in thermoelectric half-Heusler Nb1-x CoSb is investigated, for which different local orderings are observed. It is shown that the vacancy distribution follows a vacancy repulsion model and the crystal composition is found always to be close to x = 1/6 irrespective of nominal sample composition. However, the specific synthesis method controls the local order and thereby the thermoelectric properties thus providing a new frontier for tuning material properties.