Femtosecond Mamyshev oscillator at 920 nm.

A femtosecond all-PM-fiber Mamyshev oscillator (MO) at 920 nm is presented. It is based on a neodymium-doped fiber with a W-type index profile that effectively suppresses the emission around 1064 nm. The linear cavity is bounded by two near-zero dispersion fiber Bragg gratings with Gaussian reflectivity profiles. The laser is self-starting and generates up to 10-nJ pulses at a repetition rate of 41 MHz. The pulses can be compressed to 53 fs with a grating-pair compressor. To our knowledge, this is the first Mamyshev oscillator and also the highest energy femtosecond fiber oscillator demonstrated in this spectral region.

Mid-infrared tunable filter based on a femtosecond-written silica volume Bragg grating.

A silica volume Bragg grating (VBG) is used to filter the light of a mid-infrared (mid-IR) supercontinuum laser. The VBG with a 7 µm period was inscribed with 800 nm pulses with a 100 fs duration and the phase-mask technique over a glass thickness of 3 mm. Despite silica's absorption, the VBG allows obtaining a narrowband light source tunable from 2.9 to 4.2 µm with a full width at half maximum (FWHM) of 29 nm. This demonstrates the great potential of using femtosecond-written VBGs as highly tunable, yet selective, spectral filters in the mid-IR.

High-efficiency radiation-balanced Yb-doped silica fiber laser with 200-mW output.

The focus of this study was the development of a second generation of fiber lasers internally cooled by anti-Stokes fluorescence. The laser consisted of a length of a single-mode fiber spliced to fiber Bragg gratings to form the optical resonator. The fiber was single-moded at the pump (1040 nm) and signal (1064 nm) wavelengths. Its core was heavily doped with Yb, in the initial form of CaF2 nanoparticles, and co-doped with Al to reduce quenching and improve the cooling efficiency. After optimizing the fiber length (4.1 m) and output-coupler reflectivity (3.3%), the fiber laser exhibited a threshold of 160 mW, an optical efficiency of 56.8%, and a radiation-balanced output power (no net heat generation) of 192 mW. On all three metrics, this performance is significantly better than the only previously reported radiation-balanced fiber laser, which is even more meaningful given that the small size of the single-mode fiber core (7.8-µm diameter). At the maximum output power (∼2 W), the average fiber temperature was still barely above room temperature (428 mK). This work demonstrates that with anti-Stokes pumping, it is possible to induce significant gain and energy storage in a small-core Yb-doped fiber while keeping the fiber cool.

1.7 W holmium-doped fluoroindate fiber laser at 3920 nm.

A monolithic fiber laser emitting 1.7 W at 3920 nm is experimentally demonstrated in a Ho3+:InF3 fiber. The cavity comprises a pair of highly reflective fiber Bragg gratings written in the active fiber with the femtosecond phase-mask scanning technique and is spliced to the pump diode with a robust silica-to-fluoride fiber splice. This work is an important step toward high-power all-fiber laser operating in the vicinity of 4 µm.

Demonstration of Type A volume Bragg gratings inscribed with a femtosecond Gaussian-Bessel laser beam.

To our knowledge, we report on the first demonstration of Type A VBGs inscribed in silver-containing phosphate glasses by femtosecond laser writing. The gratings are inscribed plane-by-plane by scanning the voxel of a 1030 nm Gaussian-Bessel inscription beam. This results in a refractive-index modification zone, induced by the appearance of silver clusters, extending over a much larger depth than those obtained with standard Gaussian beams. As a result, a high diffraction efficiency of 95% at 632.8 nm is demonstrated for a 2-µm period transmission grating with a 150-µm effective thickness indicating a strong refractive-index modulation of 1.78 × 10-3. Meanwhile, a refractive-index modulation of 1.37 × 10-3 was observed at a wavelength of 1.55 µm. Thus, this work opens the avenue for highly effective femtosecond-written VBGs suitable for industrial applications.

Femtosecond writing of intra-phase-mask volume Bragg gratings.

In this Letter, we report the first, to the best of our knowledge, femtosecond inscription of volume Bragg gratings (VBGs) directly inside phase-mask substrates. This approach showcases enhanced robustness as both the interference pattern generated by the phase mask and the writing medium are inherently bonded together. The technique is employed with 266-nm femtosecond pulses loosely focused by a 400-mm focal length cylindrical mirror inside fused-silica and fused-quartz phase-mask samples. Such a long focal length reduces the aberrations induced by the refractive-index mismatch at the air/glass interface which allows to inscribe a refractive-index modulation simultaneously over a glass depth reaching 1.5 mm. A decreasing gradient of the modulation amplitude from 5.9 × 10-4 at the surface to 1 × 10-5 at a 1.5-mm depth is observed. This technique has therefore the potential of increasing significantly the inscription depth of femtosecond-written VBGs.

Visible femtosecond fiber laser.

Femtosecond fiber lasers have revolutionized the industry of laser technology by providing ultrashort pulses of high brightness through compact, affordable, and reliable setups. In this work, we extend the scope of application of such sources by reporting, to our knowledge, the first femtosecond fiber laser operating in the visible spectrum. The passively mode-locked ring cavity is based on nonlinear polarization evolution in a single-mode Pr3+-doped fluoride fiber and runs in an all-normal dispersion regime. Compressed pulses at 635 nm have a duration of 168 fs, a peak power of 0.73 kW, and a repetition rate of 137 MHz.

Monolithic silica fiber laser operating at 585 nm.

We report, to the best of our knowledge, the first monolithic silica fiber laser operating in the visible. The laser cavity is based on a dysprosium-doped aluminosilicate fiber bounded by a pair of fiber Bragg gratings operating at 585 nm. The yellow laser signal reaches a record output power of 147 mW. Although the pump irradiation causes photodarkening, significant reduction of the photoinduced absorption losses is demonstrated via a photobleaching process with visible light.

Towards real-time active imaging of greenhouse gases using tunable mid-infrared all-fiber lasers.

We report a tunable all-fiber laser emitting a maximum output power of 2.55 W around 3240 nm. The fiber laser cavity based on a fluoride fiber doped with dysprosium ions yields an efficiency of 42% according to the in-band launched pump power at 2825 nm. Due to a custom piezoelectric fiber Bragg grating (FBG) package, mechanical strains applied to the narrowband FBG used as the input cavity coupler allowed for fast tuning of the emission wavelength over a spectral range of 1.5 nm. This laser was deployed in the field in northern Québec (Canada) to assess its performances for remote sensing of methane in the presence of a significant amount of water vapor, i.e., over a hydroelectric reservoir. The preliminary results acquired during this field campaign confirm the great potential of the proposed approach for the development of a real-time active imaging system of greenhouse gases.

Real-Time Temperature Correction of Medical Range Fiber Bragg Gratings Dosimeters.

The interest in fiber Bragg gratings dosimeters for radiotherapy dosimetry lies in their (i) submillimeter size, (ii) multi-points dose measurements, and (iii) customizable spatial resolution. However, since the radiation measurement relies on the thermal expansion of the surrounding polymer coating, such sensors are strongly temperature dependent, which needs to be accounted for; otherwise, the errors on measurements can be higher than the measurements themselves. In this paper, we test and compare four techniques for temperature compensation: two types of dual grating techniques using different coatings, a pre-irradiation and post-irradiation temperature drift technique, which is used for calorimetry, and finally, we developed a real-time interpolated temperature gradient for the multi-points dosimetry technique. We show that, over these four tested techniques, the last one outperforms the others and allows for real-time temperature correction when an array of 13 fiber Bragg gratings spatially extending over the irradiation zone is used. For a 20 Gy irradiation, this technique reduces the measurement errors from 200% to about 10%, making it suitable for a radiotherapy dose range. Temperature correction for medical low-dose range dosimetry is a first in our field and is essential for clinical FBG dosimetry applications.

Augmented wide area circumferential catheter ablation for reduction of atrial fibrillation recurrence (AWARE) trial: Design and rationale.

BACKGROUND: Recurrence of atrial fibrillation (AF) after a pulmonary vein isolation procedure is often due to electrical reconnection of the pulmonary veins. Repeat ablation procedures may improve freedom from AF but are associated with increased risks and health care costs. A novel ablation strategy in which patients receive "augmented" ablation lesions has the potential to reduce the risk of AF recurrence. OBJECTIVE: The Augmented Wide Area Circumferential Catheter Ablation for Reduction of Atrial Fibrillation Recurrence (AWARE) Trial was designed to evaluate whether an augmented wide-area circumferential antral (WACA) ablation strategy will result in fewer atrial arrhythmia recurrences in patients with symptomatic paroxysmal AF, compared with a conventional WACA strategy. METHODS/DESIGN: The AWARE trial was a multicenter, prospective, randomized, open, blinded endpoint trial that has completed recruitment (ClinicalTrials.gov NCT02150902). Patients were randomly assigned (1:1) to either the control arm (single WACAlesion set) or the interventional arm (augmented- double WACA lesion set performed after the initial WACA). The primary outcome was atrial tachyarrhythmia (AA; atrial tachycardia [AT], atrial flutter [AFl] or AF) recurrence between days 91 and 365 post catheter ablation. Patient follow-up included 14-day continuous ambulatory ECG monitoring at 3, 6, and 12 months after catheter ablation. Three questionnaires were administered during the trial- the EuroQuol-5D (EQ-5D) quality of life scale, the Canadian Cardiovascular Society Severity of Atrial Fibrillation scale, and a patient satisfaction scale. DISCUSSION: The AWARE trial was designed to evaluate whether a novel approach to catheter ablation reduced the risk of AA recurrence in patients with symptomatic paroxysmal AF.

Large area Bragg grating for pump recycling in cladding-pumped multicore erbium-doped fiber amplifiers.

We demonstrate for the first time that a Bragg grating can be written over a large area inside the cladding of a multicore erbium-doped fiber amplifier to increase the power conversion efficiency (PCE) by recycling the output pump power. Our results indicate that a Bragg grating covering ∼25% of the cladding area allows us to recycle 19% of the output pump power which leads to a relative increase of the PCE by 16% for an input pump power of 10.6 W in the specific case of an eight-core erbium-doped fiber with a length of 20.3 m and one core loaded with an input signal power of 1.5 dBm.

Dysprosium-doped silica fiber as saturable absorber for mid-infrared pulsed all-fiber lasers.

We report on a mid-infrared Q-switched erbium-doped all-fiber laser using a dysprosium-doped silica fiber as saturable absorber for the first time in this wavelength range. Moreover, we demonstrate the use of a highly reflective chirped fiber Bragg grating written in a silica fiber as the input coupler for such lasers. This Q-switched all-fiber laser generates a stable pulse train centered at 2798 nm with a maximum average power of 670 mW at a repetition rate of 140 kHz with a pulse duration of 240 ns and a pulse energy of 4.9 µJ.

Recent developments in lanthanide-doped mid-infrared fluoride fiber lasers [Invited].

Mid-infrared fiber sources, emitting between 2.5 µm and 5.0 µm, are interesting for their great potential in several application fields such as material processing, biomedicine, remote sensing and infrared countermeasures due to their high-power, their diffraction-limited beam quality as well as their robust monolithic architecture. In this review, we will focus on the recent progress in continuous wave and pulsed mid-infrared fiber lasers and the components that bring these laser sources closer to a field deployment as well as in industrial systems. Accordingly, we will briefly illustrate the potential of such mid-infrared fiber lasers through a few selected applications.

Wavelength stabilization of high-power laser diodes using Bragg gratings inscribed in their highly multimode fiber pigtails.

Efficient wavelength stabilization of an off-the-shelf high-power laser diode operating at 976 nm is demonstrated by using a highly multimode fiber Bragg grating (FBG). This first-order grating is inscribed with 400 nm femtosecond pulses inside the 200 µm/0.22 NA pure silica core of the diode's fiber pigtail. The FBG reduces the wavelength thermal drift of the 70 W diode by a factor of 12 while also reducing its emission linewidth by a factor of 2.8. At maximum output power, a power penalty of only 6% is measured. This promising approach offers a robust and compact scheme to stabilize the spectrum of high-power laser diodes that are particularly useful for fiber-laser pumping.

Femtosecond inscription of large-area fiber Bragg gratings for high-power cladding pump reflection.

A new, to the best of our knowledge, method for inscribing fiber Bragg gratings inside a fiber's cladding based on the motorized rotation of the fiber is reported. By minimizing the aberrations induced by the fiber curvature on the femtosecond writing beam, this technique based on a phase mask allows to cover large transverse areas of a standard high-power fiber's cladding. With this approach, a first-order Bragg grating was inscribed in the pure-silica inner cladding of a 20/400-µm fiber. It was then implemented as a pump reflector at the end of a 36-m-long Yb-doped fiber laser reaching 600 W of output power, confirming the power handling capabilities of such a component. Comparison of the laser performances with and without the pump reflector showcases its great potential for increasing pump absorption inside cladding-pumped fiber lasers, which paves the way for significantly reducing their active fiber length.

15†W monolithic fiber laser at 3.55†µm.

We report a dual-wavelength-pumped all-fiber continuous-wave (CW) laser operating at 3.55 µm that reached an output power of 14.9 W, which is, to the best of our knowledge, a record. The laser cavity, made of an erbium-doped fluoride fiber and bounded by two fiber Bragg gratings (FBGs), operates at an overall optical efficiency of 17.2% and a slope efficiency of 51.3% with respect to the 1976 nm launched pump power. The all-fiber design of the cavity not only allows for significant power scaling of the laser output, but also improves its long-term stability at high output power. The cavity design was set according to a numerical optimization that showed very good agreement with the experimental results.

Ultrafast laser writing of arbitrary long low-loss waveguides in optical fibers.

We propose an innovative femtosecond laser writing approach, based on a reel-to-reel configuration, allowing the fabrication of arbitrary long optical waveguides in coreless optical fibers directly through the coating. We report few meters long waveguides operating in the near-infrared (near-IR) with propagation losses as low as 0.055 ± 0.004 dB/cm at 700 nm. The refractive index distribution is shown to be homogeneous with a quasi-circular cross section, its contrast being controllable via the writing velocity. Our work paves the way for the direct fabrication of complex arrangements of cores in standard and exotic optical fibers.

Anti-Stokes fluorescence cooling of nanoparticle-doped silica fibers.

The first observation of cooling by anti-Stokes pumping in nanoparticle-doped silica fibers is reported. Four Yb-doped fibers fabricated using conventional modified chemical vapor deposition (MCVD) techniques were evaluated, namely, an aluminosilicate fiber and three fibers in which the Yb ions were encapsulated in CaF2, SrF2, or BaF2 nanoparticles. The nanoparticles, which oxidize during preform processing, provide a modified chemical environment for the Yb3+ ions that is beneficial to cooling. When pumped at the near-optimum cooling wavelength of 1040 nm at atmospheric pressure, the fibers experienced a maximum measured temperature drop of 20.5 mK (aluminosilicate fiber), 26.2 mK (CaF2 fiber), and 16.7 mK (SrF2 fiber). The BaF2 fiber did not cool but warmed slightly. The three fibers that cooled had a cooling efficiency comparable to that of the best previously reported Yb-doped silica fiber that cooled. Data analysis shows that this efficiency is explained by the fibers' high critical quenching concentration and low residual absorptive loss (linked to sub-ppm OH contamination). This study demonstrates the large untapped potential of nanoparticle doping in the current search for silicate compositions that produce optimum anti-Stokes cooling.

Fatigue Performance of Type I and Type II Fibre Bragg Gratings Fabricated by Femtosecond Laser Inscription through the Coating.

Strain sensing technology using fibre Bragg grating (FBG) sensors is an attractive capability for aerospace structural health monitoring (SHM) and assessment because they offer resistance to harsh environments, low maintenance, and potential for high density and high strain sensing. The development of FBG inscription techniques through the fibre polymer coating using infrared (IR) lasers has overcome the mechanical weaknesses introduced by removal of the fibre coating, which is typically required for conventional UV laser inscription of FBGs. Type I and Type II femtosecond gratings are fabricated using through-coating inscription techniques, but the higher laser energy used for Type II gratings damages the glass fibre core, impacting mechanical performance. This paper investigates the fatigue performance of Type I and Type II through-coating FBG sensors with different fibre geometries and photosensitisation approaches to evaluate their overall reliability and durability, with a view to assess their performance for potential use in civil and defence SHM applications. The fatigue performance of FBG sensors was assessed under high-strain and high-frequency mechanical loading conditions by using a custom-designed electro-dynamically actuated loading assembly. In addition, pre- and post-fatigue microscopic analyses and high-resolution reflection spectrum characterisation were conducted to investigate the failure regions of the fibres and the effect of fatigue loading on reflection spectrum features. As expected, Type I gratings had a significantly higher fatigue life compared to Type II gratings. However, Type II gratings performed significantly better than conventional UV laser-inscribed FBGs and electrical foil strain gauges. Type II gratings withstand higher temperatures, and are therefore more suitable for application in harsh environments.