Optimization of electrospray ionization conditions to enhance formation of doubly protonated peptide ions with and without addition of chromium(III).

RATIONALE: Production of multiply protonated ions by electrospray ionization (ESI) is important to the analysis of peptides by mass spectrometry. For small neutral and acidic peptides, addition of chromium(III) greatly increases the intensity of doubly protonated ions. The current study examines instrumental and solution parameters that maximize peptide ion charge by ESI. METHODS: The neutral and basic heptapeptides AAAAAAA (A7) and AAAKAAA (A3KA3) were used as test compounds and electrosprayed from a solution containing chromium(III) nitrate at a peptide to metal molar ratio of 1:10. Positive ion mode experiments were performed on a Bruker HCTultra PTM Discovery System quadrupole ion trap mass spectrometer. Source voltages and drying/nebulizer gases were systematically altered. The effects of rinsing, brand, and color of plastic microcentrifuge tubes (vials) employed were also investigated. RESULTS: Nebulizer gas pressure and drying gas flow rate are crucial parameters for production of [M + 2H]2+ , while drying gas temperature alone has minimal effect. Optimization of the capillary exit and skimmer voltages are important both to maximize [M + 2H]2+ and reduce unwanted ion dissociation. Protonation is enhanced and fewer impurity peaks are observed when solutions are prepared in colorless plastic vials that have been rinsed briefly with propan-2-ol (isopropanol). CONCLUSIONS: Optimization of instrument and sample preparation factors for enhanced protonation with and without Cr(III) is necessary to allow maximum formation of [M + 2H]2+ . Proteomics researchers should find these procedures to be of use for increasing multiply protonated signal intensity even in the absence of Cr(III). Copyright © 2017 John Wiley & Sons, Ltd.

Spectroscopic and biological activity studies of the chromium-binding peptide EEEEGDD.

While trivalent chromium has been shown at high doses to have pharmacological effects improving insulin resistance in rodent models of insulin resistance, the mechanism of action of chromium at a molecular level is not known. The chromium-binding and transport agent low-molecular-weight chromium-binding substance (LMWCr) has been proposed to be the biologically active form of chromium. LMWCr has recently been shown to be comprised of a heptapeptide of the sequence EEEEDGG. The binding of Cr(3+) to this heptapeptide has been examined. Mass spectrometric and a variety of spectroscopic studies have shown that multiple chromic ions bind to the peptide in an octahedral fashion through carboxylate groups and potentially small anionic ligands such as oxide and hydroxide. A complex of Cr and the peptide when administered intravenously to mice is able to decrease area under the curve in intravenous glucose tolerance tests. It can also restore insulin-stimulated glucose uptake in myotubes rendered insulin resistant by treating them with a high-glucose media.

MALDI MS in-source decay of glycans using a glutathione-capped iron oxide nanoparticle matrix.

A new matrix-assisted laser desorption ionization (MALDI) mass spectrometry matrix is proposed for molecular mass and structural determination of glycans. This matrix contains an iron oxide nanoparticle (NP) core with gluthathione (GSH) molecules covalently bound to the surface. As demonstrated for the monosaccharide glucose and several larger glycans, the mass spectra exhibit good analyte ion intensities and signal-to-noise ratios, as well as an exceptionally clean background in the low mass-to-charge (m/z) region. In addition, abundant in-source decay (ISD) occurs when the laser power is increased above the ionization threshold; this indicates that the matrix provides strong energy transfer to the sample. For five model glycans, ISD produced extensive glycosidic and cross-ring cleavages in the positive ion mode from singly charged precursor ions with bound sodium ions. Linear, branched, and cyclic glycans were employed, and all were found to undergo abundant fragmentation by ISD. (18)O labeling was used to clarify m/z assignment ambiguities and showed that the majority of the fragmentation originates from the nonreducing ends of the glycans. Studies with a peracetylated glycan indicated that abundant ISD fragmentation occurs even in the absence of hydroxyl groups. The ISD product ions generated using this new matrix should prove useful in the sequencing of glycans.

Paramagnetic 19F NMR and Electrospray Ionization Mass Spectrometric Studies of Substituted Pyridine Complexes of Chromium(III): Models for Potential Use of 19F NMR to Probe Cr(III)-Nucleotide Interaction.

The synthesis and characterization of chromium basic carboxylate complexes, [Cr3(O2CR)6L3]+, containing trifluoroacetate, 3-fluoropyridine, 3-trifluoromethylpyridine, and 4-trifluoromethylpyridine are described. The substituted pyridine ligands are used as models of DNA bases to determine whether 19F NMR would be a potentially useful probe of the binding of Cr3+ to DNA. The 19F NMR resonances of the coordinated ligands, while broadened by delocalization of unpaired electron density from the S=3/2 chromic centers, are readily discernable, and the contact shifts are of sufficient magnitude that the signals from coordinated and free ligands can easily be differentiated. Thus, 19F NMR appears to be a potentially useful probe of the binding of Cr3+ to DNA containing F-labeled bases. Additionally, electrospray MS is shown to be a convenient method to establish the identity of chromium basic carboxylate assemblies.

In-Source Decay MALDI and High-Energy Collision-Induced Dissociation Mass Spectrometry of Alkali Metal-Adducted Underivatized Oligosaccharides.

In-source decay (ISD) and high-energy collision-induced dissociation (HE-CID) were explored to provide structural information on alkali metal-adducted linear and stacked oligosaccharides (oligosaccharides with increased flexibility due to linkage type). These oligosaccharides include isomeric tetrasaccharides, maltoheptaose, and several human milk oligosaccharides (HMOs). Matrix-assisted laser desorption ionization (MALDI) ion production efficiency, as well as the product ion intensities, and the number of product ions formed in ISD and HE-CID of these oligosaccharides were influenced by the matrix, the ionic radius of the metal ion used for adduction, and the affinity of metal ions for specific functional groups in the oligosaccharides. 2,4,6-Trihydroxyacetophenone (THAP) was the best matrix for HE-CID of oligosaccharides, 4-dimethylaminobenzaldehyde (DMABA) worked best for ISD of tetrasaccharides and pentasaccharides, while 2,5-dihydroxybenzoic acid (DHB) was the best matrix for ISD and HE-CID of long chain oligosaccharides. In general, the number of product ions formed followed the trend Li+ > Na+ > K+ > Rb+ > Cs+, except for HMOs where Na+ ≥ Li+ > K+ > Rb+ > Cs+ occurred. The type of product ions formed and their intensities varied based on the position of the glycosidic bond linkage and the content of the monosaccharide. ISD and HE-CID produced diagnostic ions that could structurally differentiate isomers. Overall, HE-CID of alkali-metal adducted oligosaccharides produces intense glycosidic bond cleavages and low intensity cross-ring and internal cleavages. In contrast, ISD generates mainly cross-ring cleavages and internal cleavages at intensities higher than in HE-CID. In addition, ISD produced unique product ions that complement results from HE-CID.

Characterization of the organic component of low-molecular-weight chromium-binding substance and its binding of chromium.

Chromium was proposed to be an essential element over 50 y ago and was shown to have therapeutic potential in treating the symptoms of type 2 diabetes; however, its mechanism of action at a molecular level is unknown. One chromium-binding biomolecule, low-molecular weight chromium-binding substance (LMWCr or chromodulin), has been found to be biologically active in in vitro assays and proposed as a potential candidate for the in vivo biologically active form of chromium. Characterization of the organic component of LMWCr has proven difficult. Treating bovine LMWCr with trifluoroacetic acid followed by purification on a graphite powder micro-column generates a heptapeptide fragment of LMWCr. The peptide sequence of the fragment was analyzed by MS and tandem MS (MS/MS and MS/MS/MS) using collision-induced dissociation and post-source decay. Two candidate sequences, pEEEEGDD and pEEEGEDD (where pE is pyroglutamate), were identified from the MS/MS experiments; additional tandem MS suggests the sequence is pEEEEGDD. The N-terminal glutamate residues explain the inability to sequence LMWCr by the Edman method. Langmuir isotherms and Hill plots were used to analyze the binding constants of chromic ions to synthetic peptides similar in composition to apoLMWCr. The sequence pEEEEGDD was found to bind 4 chromic ions per peptide with nearly identical cooperativity and binding constants to those of apoLMWCr. This work should lead to further studies elucidating or eliminating a potential role for LMWCr in treating the symptoms of type 2 diabetes and other conditions resulting from improper carbohydrate and lipid metabolism.

Mechanistic Study of Enhanced Protonation by Chromium(III) in Electrospray Ionization: A Superacid Bound to a Peptide.

Addition of trivalent chromium, Cr(III), to solutions undergoing electrospray ionization (ESI) enhances protonation and leads to formation of [M + 2H]2+ for peptides that normally produce [M + H]+. This effect is explored using electronic structure calculations at the density functional theory (DFT) level to predict the energetics of various species that are potentially important to the mechanism. Gas- and solution-phase reaction free energies for glycine and its anion reacting with [Cr(III)(H2O)6]3+ and for dehydration of these species have been predicted, where glycine is used as a simple model for a peptide. For comparison, calculations were also performed with Fe(III), Al(III), Sc(III), Y(III), and La(III). Removal of water from these complexes, as would occur during the ESI desolvation process, results in species that are highly acidic. The calculated pKa of Cr(III) with a single solvation shell is -10.8, making [Cr(III)(H2O)6]3+ a superacid that is more acidic than sulfuric acid (pKa = -8.8). Binding to glycine requires removal of two aqua ligands, which gives [Cr(III)(H2O)4]3+ that has an extremely acidic pKa of -28.8. Removal of additional water further enhances acidity, reaching a pKa of -84.7 for [Cr(III)(H2O)]3+. A mechanism for enhanced protonation is proposed that incorporates computational and experiment results, as well as information on the known chemistry of Cr(III), which is substitutionally inert. The initial step involves binding of [Cr(III)(H2O)4]3+ to the deprotonated C-terminus of a peptide. As the drying process during ESI strips water from the complex, the resulting superacid transfers protons to the bound peptide, eventually leading to formation of [M + 2H]2+.

Experimental and Computational Study of the Gas-Phase Acidities of Acidic Di- and Tripeptides.

Gas-phase acidities (GA or Δ Gacid) of acidic di- and tripeptides are determined for the first time. The peptides studied are composed of inert alanine (A) residues and one X residue of either aspartic acid (D) or glutamic acid (E): AX, XA, AAX, AXA, and XAA. Experimental GAs were measured by the thermokinetic method of deprotonation ion/molecule reactions in a Fourier transform ion cyclotron resonance mass spectrometer. Calculated GAs were obtained by composite correlated molecular orbital theory at the G3(MP2) level for deprotonation of carboxylic acid groups both at the C-terminus and at the side chain. Excellent agreement was found between experimental and calculated GA values. There is a slight preference for peptides with D being more acidic than analogous peptides with E, which agrees with the GAs of the corresponding amino acids. Experiments showed that peptides are more acidic (lower numerical GA values) when the acidic residue is located at the C-terminus (i.e., AX or AAX). The lowest energy form of deprotonated AAE has a unique structure where the longer side chain of E allows the two carboxylates, which are in close proximity, to share the proton. The tripeptides are less acidic (higher GA value) by 3-7 kcal/mol when the acidic residue is in the center. The tripeptides are more acidic (by 2-10 kcal/mol) than dipeptides containing the same acidic residue at the same location.

The effects of chromium(III) coordination on the dissociation of acidic peptides.

The complexes formed between chromium(III) and synthetic acidic peptides were studied by sustained off-resonance irradiation collision-induced dissociation (SORI-CID) in a Fourier transform ion-cyclotron resonance (FT-ICR) mass spectrometer equipped with electrospray ionization (ESI). Neutral peptides and peptides containing one, two, and multiple acidic residues were studied. Formation of [M + Cr-2H]+ occurred for all peptides. Three noteworthy features were found in the CID spectra of [M + Cr-2H]+. The first is that fewer fragment ions were produced from [M + Cr-2H]+ than from [M + H]+. The reason may be that multiple coordination between chromium(III) and carboxylate or carbonyl groups hinders the production of fragment ions by continuing to bind pieces of the peptide to chromium(III) after cleavage of bonds within the peptide. The second feature is loss of CO from [M + Cr-2H]+ and [y(n) + Cr-H]+. A mechanism involving coordination of chromium(III) with carboxylate groups is proposed to rationalize elimination of CO. The third feature is that chromium(III) is retained in all fragment ions, indicating strong binding of the metal ion to the peptides. The complex [M + 2Cr-5H]+ is formed as the peptide chain length and number of acidic residues increases. Longer peptides have more sites to coordinate with chromium(III) and more conformational flexibility. In addition, formation of [M + Cr-2H]+ from AGGAAAA-OCH(3), which has no carboxylic acid groups, suggests that chromium(III) can coordinate with sites on the peptide backbone, albeit in low abundance. In the negative mode, [M + Cr-4H](-) was only found for peptides containing four or more carboxylic acid groups. This is consistent with deprotonated carboxylic acid groups being involved in chromium(III) coordination and with chromium existing in the 3 + state in the gas-phase ions.

Electron transfer dissociation mass spectrometry of acidic phosphorylated peptides cationized with trivalent praseodymium.

The lanthanide ion praseodymium, Pr(III), was employed to study metallated ion formation and electron transfer dissociation (ETD) of 27 biological and model highly acidic phosphopeptides. All phosphopeptides investigated form metallated ions by electrospray ionization (ESI) that can be studied by ETD to yield abundant sequence information. The ions formed are [M + Pr - H]2+ , [M + Pr]3+ , and [M + Pr + H]4+ . All biological phosphopeptides with a chain length of seven or more residues generate [M + Pr]3+ . For biological phosphopeptides, [M + Pr]3+ undergoes more backbone cleavage by ETD than [M + Pr - H]2+ and, in some cases, full sequence coverage occurs. Acidic model phosphorylated hexa-peptides and octa-peptides, composed of alanine residues and one phosphorylated residue, form exclusively [M + Pr - H]2+ by ESI. Limited sequence information is obtained by ETD of [M + Pr - H]2+ with only metallated product ions being generated. For two biological phosphopeptides, [M + Pr + H]4+ is observed and may be due to the presence of at least one residue with a highly basic side chain that facilitates the addition of an extra proton. For the model phosphopeptides, more sequence coverage occurs when the phosphorylated residue is in the middle of the sequence than at either the N- or C-terminus. ETD of the metallated precursor ions formed by ESI generates exclusively metallated and nonmetallated c- and z-ions for the biological phosphopeptides, while metallated c-ions, z-ions, and a few y-ions form for the model phosphopeptides. Most of the product ions contain the phosphorylated residue indicating that the metal ion binds predominantly at the deprotonated phosphate group. The results of this study indicate that ETD is a promising tool for sequencing highly acidic phosphorylated peptides by metal adduction with Pr (III) and, by extension, all nonradioactive lanthanide metal ions.

Electron Transfer Dissociation and Collision-Induced Dissociation of Underivatized Metallated Oligosaccharides.

Electron transfer dissociation (ETD) and collision-induced dissociation (CID) were used to investigate underivatized, metal-cationized oligosaccharides formed via electrospray ionization (ESI). Reducing and non-reducing sugars were studied including the tetrasaccharides maltotetraose, 3α,4ß,3α-galactotetraose, stachyose, nystose, and a heptasaccharide, maltoheptaose. Univalent alkali, divalent alkaline earth, divalent and trivalent transition metal ions, and a boron group trivalent metal ion were adducted to the non-permethylated oligosaccharides. ESI generated [M + Met]+, [M + 2Met]2+, [M + Met]2+, [M + Met - H]+, and [M + Met - 2H]+ most intensely along with low intensity nitrate adducts, depending on the metal and sugar ionized. The ability of these metal ions to produce oligosaccharide adduct ions by ESI had the general trend: Ca(II) > Mg(II) > Ni(II) > Co(II) > Zn(II) > Cu(II) > Na(I) > K(I) > Al(III) ≈ Fe(III) ≈ Cr(III). Although trivalent metals were utilized, no triply charged ions were formed. Metal cations allowed for high ESI signal intensity without permethylation. ETD and CID on [M + Met]2+ produced various glycosidic and cross-ring cleavages, with ETD producing more cross-ring and internal ions, which are useful for structural analysis. Product ion intensities varied based on glycosidic-bond linkage and identity of monosaccharide sub-unit, and metal adducts. ETD and CID showed high fragmentation efficiency, often with complete precursor dissociation, depending on the identity of the adducted metal ion. Loss of water was occasionally observed, but elimination of small neutral molecules was not prevalent. For both ETD and CID, [M + Co]2+ produced the most uniform structurally informative dissociation with all oligosaccharides studied. The ETD and CID spectra were complementary. Graphical Abstract ᅟ.

The use of chromium(III) complexes to enhance peptide protonation by electrospray ionization mass spectrometry.

The addition of trivalent chromium, Cr(III), reagents to peptide solutions can increase the intensity of doubly protonated peptides, [M + 2H]2+ , through electrospray ionization (ESI). Three model heptapeptides were studied: neutral (AAAAAAA), acidic (AAEEEAA), and basic (AAAKAAA). The neutral and acidic peptides form almost no 2+ ions in the absence of Cr(III). Twenty Cr(III) complexes were used as potential enhanced protonation reagents, including 11 complexes with nonlabile ligands and nine with labile ligands. The complexes that provide the most abundant [M + 2H]2+ , the greatest [M + 2H]2+ to [M + H]+ ratio, and the cleanest mass spectra are [Cr(H2 O)6 ](NO3 )3 ·3H2 O and [Cr(THF)3 ]Cl3 . Anions in Cr(III) reagents can also affect the intensity of [M + 2H]2+ and the [M + 2H]2+ to [M + H]+ ratio through cation-anion interactions. The influence of anions on the extent of peptide protonation follows the trend ClO4 -  Ëƒ SO4 2-  Ëƒ Br-  Ëƒ Cl-  Ëƒ F-  ≈ NO3 - . Solvent effects and complexes with varying number of water ligands were investigated to study the importance of water in enhanced protonation. Aqueous solvent systems and Cr(III) complexes that have at least one bound water ligand in solution must be used for successful increase in the intensity of [M + 2H]2+ , which indicates that water is involved in the mechanism of Cr(III)-induced enhanced protonation. The ESI source design is also important because no enhanced protonation was observed using a Z-spray source. The current results suggest that this Cr(III)-induced effect occurs during the ESI desolvation process.

Effects of acidic peptide size and sequence on trivalent praseodymium adduction and electron transfer dissociation mass spectrometry.

Using the lanthanide ion praseodymium, Pr(III), metallated ion formation and electron transfer dissociation (ETD) were studied for 25 biological and model acidic peptides. For chain lengths of seven or more residues, even highly acidic peptides that can be difficult to protonate by electrospray ionization will metallate and undergo abundant ETD fragmentation. Peptides composed of predominantly acidic residues form only the deprotonated ion, [M + Pr - H]2+ ; this ion yields near complete ETD sequence coverage for larger peptides. Peptides with a mixture of acidic and neutral residues generate [M + Pr]3+ , which cleaves between every residue for many peptides. Acidic peptides that contain at least one residue with a basic side chain also produce the protonated ion, [M + Pr + H]4+ ; this ion undergoes the most extensive sequence coverage by ETD. Primarily metallated and non-metallated c- and z-ions form for all peptides investigated. Metal adducted product ions are only present when at least half of the peptide sequence can be incorporated into the ion; this suggests that the metal ion simultaneously attaches to more than one acidic site. The only site consistently lacking dissociation is at the N-terminal side of a proline residue. Increasing peptide chain length generates more backbone cleavage for metal-peptide complexes with the same charge state. For acidic peptides with the same length, increasing the precursor ion charge state from 2+ to 3+ also leads to more cleavage. The results of this study indicate that highly acidic peptides can be sequenced by ETD of complexes formed with Pr(III). Copyright © 2017 John Wiley & Sons, Ltd.

Citric Acid Capped Iron Oxide Nanoparticles as an Effective MALDI Matrix for Polymers.

A new matrix-assisted laser desorption ionization (MALDI) mass spectrometry matrix is proposed for molecular mass determination of polymers. This matrix contains an iron oxide nanoparticle (NP) core with citric acid (CA) molecules covalently bound to the surface. With the assistance of additives, the particulate nature of NPs allows the matrix to mix uniformly with polar or nonpolar polymer layers and promotes ionization, which may simplify matrix selection and sample preparation procedures. Several distinctively different polymer classes (polyethyleneglycol (PEG), polywax/polyethylene, perfluoropolyether, and polydimethylsiloxane) are effectively detected by the water or methanol dispersed NPCA matrix with NaCl, NaOH, LiOH, or AgNO3 as additives. Furtheremore, successful quantitative measurements of PEG1000 using polypropylene glycol 1000 as an internal standard are demonstrated. Graphical Abstract ᅟ.

C-terminal amino acid residue loss for deprotonated peptide ions containing glutamic acid, aspartic acid, or serine residues at the C-terminus.

Deprotonated peptides containing C-terminal glutamic acid, aspartic acid, or serine residues were studied by sustained off-resonance irradiation collision-induced dissociation (SORI-CID) in a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer with ion production by electrospray ionization (ESI). Additional studies were performed by post source decay (PSD) in a matrix-assisted laser desorption ionization/time-of-flight (MALDI/TOF) mass spectrometer. This work included both model peptides synthesized in our laboratory and bioactive peptides with more complex sequences. During SORI-CID and PSD, [M - H]- and [M - 2H]2- underwent an unusual cleavage corresponding to the elimination of the C-terminal residue. Two mechanisms are proposed to occur. They involve nucleophilic attack on the carbonyl carbon of the adjacent residue by either the carboxylate group of the C-terminus or the side chain carboxylate group of C-terminal glutamic acid and aspartic acid residues. To confirm the proposed mechanisms, AAAAAD was labelled by 18O specifically on the side chain of the aspartic acid residue. For peptides that contain multiple C-terminal glutamic acid residues, each of these residues can be sequentially eliminated from the deprotonated ions; a driving force may be the formation of a very stable pyroglutamatic acid neutral. For peptides with multiple aspartic acid residues at the C-terminus, aspartic acid residue loss is not sequential. For peptides with multiple serine residues at the C-terminus, C-terminal residue loss is sequential; however, abundant loss of other neutral molecules also occurs. In addition, the presence of basic residues (arginine or lysine) in the sequence has no effect on C-terminal residue elimination in the negative ion mode.

Low-molecular-weight chromium-binding substance from chicken liver and American alligator liver.

Low-molecular-weight chromium-binding substance (LMWCr), also known as chromodulin, is a chromium-binding oligopeptide proposed to have a function in chromium transport and insulin signaling in mammals. In this work, LMWCr has been isolated and purified for the first time from non-mammalian sources: chicken and American alligator. Milligram quantities of the oligopeptide can be obtained from kilogram quantities of liver. The LMWCr's from both sources are asparatate- and glutamate-rich oligopeptides which possess multinuclear chromium assemblies. The composition and physical and spectroscopic properties of the avian and reptilian LMWCr's are extremely similar to those of their mammalian analogues, suggesting the multinuclear sites of the biomolecule from all three classes of animal possess very similar structures. The chicken and alligator oligopeptides may possess intrinsic phosphotyrosine phosphatase activity.

The Effects of Trivalent Lanthanide Cationization on the Electron Transfer Dissociation of Acidic Fibrinopeptide B and its Analogs.

Electrospray ionization (ESI) on mixtures of acidic fibrinopeptide B and two peptide analogs with trivalent lanthanide salts generates [M + Met + H](4+), [M + Met](3+), and [M + Met -H](2+), where M = peptide and Met = metal (except radioactive promethium). These ions undergo extensive and highly efficient electron transfer dissociation (ETD) to form metallated and non-metallated c- and z-ions. All metal adducted product ions contain at least two acidic sites, which suggest attachment of the lanthanide cation at the side chains of one or more acidic residues. The three peptides undergo similar fragmentation. ETD on [M + Met + H](4+) leads to cleavage at every residue; the presence of both a metal ion and an extra proton is very effective in promoting sequence-informative fragmentation. Backbone dissociation of [M + Met](3+) is also extensive, although cleavage does not always occur between adjacent glutamic acid residues. For [M + Met - H ](2+), a more limited range of product ions form. All lanthanide metal peptide complexes display similar fragmentation except for europium (Eu). ETD on [M + Eu - H](2+) and [M + Eu](3+) yields a limited amount of peptide backbone cleavage; however, [M + Eu + H](4+) dissociates extensively with cleavage at every residue. With the exception of the results for Eu(III), metallated peptide ion formation by ESI, ETD fragmentation efficiencies, and product ion formation are unaffected by the identity of the lanthanide cation. Adduction with trivalent lanthanide metal ions is a promising tool for sequence analysis of acidic peptides by ETD. Graphical Abstract ᅟ.

Negative Ion In-Source Decay Matrix-Assisted Laser Desorption/Ionization Mass Spectrometry for Sequencing Acidic Peptides.

Matrix-assisted laser desorption/ionization (MALDI) in-source decay was studied in the negative ion mode on deprotonated peptides to determine its usefulness for obtaining extensive sequence information for acidic peptides. Eight biological acidic peptides, ranging in size from 11 to 33 residues, were studied by negative ion mode ISD (nISD). The matrices 2,5-dihydroxybenzoic acid, 2-aminobenzoic acid, 2-aminobenzamide, 1,5-diaminonaphthalene, 5-amino-1-naphthol, 3-aminoquinoline, and 9-aminoacridine were used with each peptide. Optimal fragmentation was produced with 1,5-diaminonphthalene (DAN), and extensive sequence informative fragmentation was observed for every peptide except hirudin(54-65). Cleavage at the N-Cα bond of the peptide backbone, producing c' and z' ions, was dominant for all peptides. Cleavage of the N-Cα bond N-terminal to proline residues was not observed. The formation of c and z ions is also found in electron transfer dissociation (ETD), electron capture dissociation (ECD), and positive ion mode ISD, which are considered to be radical-driven techniques. Oxidized insulin chain A, which has four highly acidic oxidized cysteine residues, had less extensive fragmentation. This peptide also exhibited the only charged localized fragmentation, with more pronounced product ion formation adjacent to the highly acidic residues. In addition, spectra were obtained by positive ion mode ISD for each protonated peptide; more sequence informative fragmentation was observed via nISD for all peptides. Three of the peptides studied had no product ion formation in ISD, but extensive sequence informative fragmentation was found in their nISD spectra. The results of this study indicate that nISD can be used to readily obtain sequence information for acidic peptides.

The use of chromium(III) to supercharge peptides by protonation at low basicity sites.

The addition of chromium(III) nitrate to solutions of peptides with seven or more residues greatly increases the formation of doubly protonated peptides, [M + 2H](2+), by electrospray ionization. The test compound heptaalanine has only one highly basic site (the N-terminal amino group) and undergoes almost exclusive single protonation using standard solvents. When Cr(III) is added to the solution, abundant [M + 2H](2+) forms, which involves protonation of the peptide backbone or the C-terminus. Salts of Al(III), Mn(II), Fe(III), Fe(II), Cu(II), Zn (II), Rh(III), La(III), Ce(IV), and Eu(III) were also studied. Although several metal ions slightly enhance protonation, Cr(III) has by far the greatest ability to generate [M + 2H](2+). Cr(III) does not supercharge peptide methyl esters, which suggests that the mechanism involves interaction of Cr(III) with a carboxylic acid group. Other factors may include the high acidity of hexa-aquochromium(III) and the resistance of Cr(III) to reduction. Nitrate salts enhance protonation more than chloride salts and a molar ratio of 10:1 Cr(III):peptide produces the most intense [M + 2H](2+). Cr(III) also supercharges numerous other small peptides, including highly acidic species. For basic peptides, Cr(III) increases the charge state (2+ versus 1+) and causes the number of peptide molecules being protonated to double or triple. Chromium(III) does not supercharge the proteins cytochrome c and myoglobin. The ability of Cr(III) to enhance [M + 2H](2+) intensity may prove useful in tandem mass spectrometry because of the resulting overall increase in signal-to-noise ratio, the fact that [M + 2H](2+) generally dissociate more readily than [M + H](+), and the ability to produce [M + 2H](2+) precursors for electron-based dissociation techniques.

Gas-Phase Acidities of Phosphorylated Amino Acids.

Gas-phase acidities and heats of formation have been predicted at the G3(MP2)/SCRF-COSMO level of theory for 10 phosphorylated amino acids and their corresponding amides, including phospho-serine (pSer), -threonine (pThr), and -tyrosine (pTyr), providing the first reliable set of these values. The gas-phase acidities (GAs) of the three named phosphorylated amino acids and their amides have been determined using proton transfer reactions in a Fourier transform ion cyclotron mass spectrometer. Excellent agreement was found between the experimental and predicted GAs. The phosphate group is the deprotonation site for pSer and pThr and deprotonation from the carboxylic acid generated the lowest energy anion for pTyr. The infrared spectra were calculated for six low energy anions of pSer, pThr, and pTyr. For deprotonated pSer and pThr, good agreement is found between the experimental IRMPD spectra and the calculated spectra for our lowest energy anion structure. For pTyr, the IR spectra for a higher energy phosphate deprotonated structure is in good agreement with experiment. Additional experiments tested electrospray ionization (ESI) conditions for pTyr and determined that variations in solvent, temperature, and voltage can result in a different experimental GA value, indicating that ESI conditions affect the conformation of the pTyr anion.