ABSTRACT
In this study, two kinds of colloidal ternary semiconductor white light-emitting quantum dots (WQDs), Zn(0.5)Cd(0.5)S and Zn(0.8)Cd(0.2)S, are prepared and used as nanophosphors in a UV light-emitting diode (UV-LED) pumping device. When the weight ratio of Zn(0.5)Cd(0.5)S WQDs is 9.1 wt. % in silicone and the drive current is set at 20 mA, the chromaticity coordinates (CIE), correlated color temperature (CCT), color rendering index (CRI), and luminous efficiency are (0.43,0.37), 2830 K, 90, and 0.94 lm/W, respectively. On the other hand, under the same weight ratio in silicone, the CIE, CCT, CRI, and luminous efficiency of Zn(0.8)Cd(0.2)S WQDs are (0.36,0.33), 4240 K, 86, and 4.12 lm/W, respectively. Based on the above results, we can conclude that WQDs-based LED can be obtained by controlling the compositions of Zn(x)Cd(1-x)S QDs due to the coexistence of band-edge and surface state emission.
ABSTRACT
Difficult separation of oil-solid phase and high fine content of the recovered oil were two problems in the treatment of oily sludge from the tank bottom by the hot water-based extraction process. To solve the problems, one technology with "ball milling + ozone-catalyzed oxidation" as the core was studied, and the process parameters of ball milling and ozone-catalyzed oxidation were respectively optimized. After ball milling treatment, the oil content of dry oily sludge decreased from 33.9 to 10.2%. Then, an ozone catalytic oxidation treatment technology with aluminum ore as the catalyst was developed to further treat this stubborn oily sludge. Under the optimal conditions, the oil content of oily sludge could be further reduced to 0.28%, which met the treatment and disposal requirements stipulated in GB4284-2018. For further research on the contribution of the catalyst to the ozone catalytic oxidation system, the reaction activation energy and reaction rates of ozone oxidation and ozone catalytic oxidation were compared from the perspective of kinetics. The results showed that, with the catalyst addition, the reaction rate constants increased about three times and the reaction activation energy reduced 82.26%, which showed the effectiveness of the catalyst on the kinetics quantitatively. The combined process with "ball milling + ozone-catalyzed oxidation" as the core can solve the two problems in the treatment of oily sludge from the tank bottom by hot water-based extraction and provides a reference for the harmless and resourceful treatment of oily sludge from the tank bottom.
ABSTRACT
Highly effective carbon supported-Pt75Au25 catalysts for oxygen reduction reaction (ORR) are prepared though titanium dioxide modification and post heat treatment. After accelerated durability test (ADT) of 1700 cycles, the ORR activity of PtAu/C catalysts modified by TiO2 and air heat treatment is 3 times higher than that of the commercial Pt/C. The enhancement of ORR activity is attributed to surface and structural alteration by air-induced Pt surface segregation and lower unfilled d states. On the contrary, for TiO2 modified and H2 treated PtAu/C catalysts, the deterioration of the ORR activity may be due to the loss of electrochemical surface area after ADT and the increase of d-band vacancy.
ABSTRACT
The combinational modification of the morphology, alloying, and support for Pt catalysts has been optimized towards the oxygen reduction reaction. Graphene-supported PtPd nanorods have lower unfilled Pt d-states than carbon-supported Pt nanoparticles (Pt/C) and their specific and mass activities after the accelerated durability test are about 6.5 and 2.7 times higher than those of Pt/C, attributed to the synergistic electronic modification effect and graphene-metal interaction.