ABSTRACT
Sports related head injuries can cause transient neurological events including loss of consciousness and dystonic posturing. However, it is unknown why head impacts that appear similar produce distinct neurological effects. The biomechanical effect of impacts can be estimated using computational models of strain within the brain. Here, we investigate the strain and strain rates produced by professional American football impacts that led to loss of consciousness, posturing or no neurological signs. We reviewed 1280 National Football League American football games and selected cases where the team's medical personnel made a diagnosis of concussion. Videos were then analysed for signs of neurological events. We identified 20 head impacts that showed clear video signs of loss of consciousness and 21 showing clear abnormal posturing. Forty-one control impacts were selected where there was no observable evidence of neurological signs, resulting in 82 videos of impacts for analysis. Video analysis was used to guide physical reconstructions of these impacts, allowing us to estimate the impact kinematics. These were then used as input to a detailed 3D high-fidelity finite element model of brain injury biomechanics to estimate strain and strain rate within the brain. We tested the hypotheses that impacts producing loss of consciousness would be associated with the highest biomechanical forces, that loss of consciousness would be associated with high forces in brainstem nuclei involved in arousal and that dystonic posturing would be associated with high forces in motor regions. Impacts leading to loss of consciousness compared to controls produced higher head acceleration (linear acceleration; 81.5 g ± 39.8 versus 47.9 ± 21.4; P = 0.004, rotational acceleration; 5.9 krad/s2 ± 2.4 versus 3.5 ± 1.6; P < 0.001) and in voxel-wise analysis produced larger brain deformation in many brain regions, including parts of the brainstem and cerebellum. Dystonic posturing was also associated with higher deformation compared to controls, with brain deformation observed in cortical regions that included the motor cortex. Loss of consciousness was specifically associated with higher strain rates in brainstem regions implicated in maintenance of consciousness, including following correction for the overall severity of impact. These included brainstem nuclei including the locus coeruleus, dorsal raphé and parabrachial complex. The results show that in head impacts producing loss of consciousness, brain deformation is disproportionately seen in brainstem regions containing nuclei involved in arousal, suggesting that head impacts produce loss of consciousness through a biomechanical effect on key brainstem nuclei involved in the maintenance of consciousness.
Subject(s)
Brain Concussion , Craniocerebral Trauma , Movement Disorders , Humans , Consciousness , Craniocerebral Trauma/complications , Brain Concussion/etiology , Head , Athletes , Movement Disorders/complications , Unconsciousness , Computer Simulation , Biomechanical PhenomenaABSTRACT
BACKGROUND: Head impacts in sports can produce brain injuries. The accurate quantification of head kinematics through instrumented mouthguards (iMG) can help identify underlying brain motion during injurious impacts. The aim of the current study is to assess the validity of an iMG across a large range of linear and rotational accelerations to allow for on-field head impact monitoring. METHODS: Drop tests of an instrumented helmeted anthropometric testing device (ATD) were performed across a range of impact magnitudes and locations, with iMG measures collected concurrently. ATD and iMG kinematics were also fed forward to high-fidelity brain models to predict maximal principal strain. RESULTS: The impacts produced a wide range of head kinematics (16-171 g, 1330-10,164 rad/s2 and 11.3-41.5 rad/s) and durations (6-18 ms), representing impacts in rugby and boxing. Comparison of the peak values across ATD and iMG indicated high levels of agreement, with a total concordance correlation coefficient of 0.97 for peak impact kinematics and 0.97 for predicted brain strain. We also found good agreement between iMG and ATD measured time-series kinematic data, with the highest normalized root mean squared error for rotational velocity (5.47 ± 2.61%) and the lowest for rotational acceleration (1.24 ± 0.86%). Our results confirm that the iMG can reliably measure laboratory-based head kinematics under a large range of accelerations and is suitable for future on-field validity assessments.
Subject(s)
Boxing , Sports , Biomechanical Phenomena , Acceleration , MotionABSTRACT
The relationship between biomechanical forces and neuropathology is key to understanding traumatic brain injury. White matter tracts are damaged by high shear forces during impact, resulting in axonal injury, a key determinant of long-term clinical outcomes. However, the relationship between biomechanical forces and patterns of white matter injuries, associated with persistent diffusion MRI abnormalities, is poorly understood. This limits the ability to predict the severity of head injuries and the design of appropriate protection. Our previously developed human finite element model of head injury predicted the location of post-traumatic neurodegeneration. A similar rat model now allows us to experimentally test whether strain patterns calculated by the model predicts in vivo MRI and histology changes. Using a controlled cortical impact, mild and moderate injuries (1 and 2 mm) were performed. Focal and axonal injuries were quantified with volumetric and diffusion 9.4 T MRI at 2 weeks post injury. Detailed analysis of the corpus callosum was conducted using multi-shell diffusion MRI and histopathology. Microglia and astrocyte density, including process parameters, along with white matter structural integrity and neurofilament expression were determined by quantitative immunohistochemistry. Linear mixed effects regression analyses for strain and strain rate with the employed outcome measures were used to ascertain how well immediate biomechanics could explain MRI and histology changes. The spatial pattern of mechanical strain and strain rate in the injured cortex shows good agreement with the probability maps of focal lesions derived from volumetric MRI. Diffusion metrics showed abnormalities in the corpus callosum, indicating white matter changes in the segments subjected to high strain, as predicted by the model. The same segments also exhibited a severity-dependent increase in glia cell density, white matter thinning and reduced neurofilament expression. Linear mixed effects regression analyses showed that mechanical strain and strain rate were significant predictors of in vivo MRI and histology changes. Specifically, strain and strain rate respectively explained 33% and 28% of the reduction in fractional anisotropy, 51% and 29% of the change in neurofilament expression and 51% and 30% of microglia density changes. The work provides evidence that strain and strain rate in the first milliseconds after injury are important factors in determining patterns of glial and axonal injury and serve as experimental validators of our computational model of traumatic brain injury. Our results provide support for the use of this model in understanding the relationship of biomechanics and neuropathology and can guide the development of head protection systems, such as airbags and helmets.
Subject(s)
Axons/pathology , Biomechanical Phenomena , Brain Injuries, Traumatic/diagnostic imaging , Brain Injuries, Traumatic/pathology , Models, Neurological , White Matter/diagnostic imaging , White Matter/pathology , Animals , Astrocytes/pathology , Corpus Callosum/diagnostic imaging , Corpus Callosum/pathology , Diffusion Magnetic Resonance Imaging , Disease Models, Animal , Finite Element Analysis , Male , Microglia/pathology , Rats, Sprague-DawleyABSTRACT
Standards for sports headgear were introduced as far back as the 1960s and many have remained substantially unchanged to present day. Since this time, headgear has virtually eliminated catastrophic head injuries such as skull fractures and changed the landscape of head injuries in sports. Mild traumatic brain injury (mTBI) is now a prevalent concern and the effectiveness of headgear in mitigating mTBI is inconclusive for most sports. Given that most current headgear standards are confined to attenuating linear head mechanics and recent brain injury studies have underscored the importance of angular mechanics in the genesis of mTBI, new or expanded standards are needed to foster headgear development and assess headgear performance that addresses all types of sport-related head and brain injuries. The aim of this review is to provide a basis for developing new sports headgear impact tests for standards by summarizing and critiquing: 1) impact testing procedures currently codified in published headgear standards for sports and 2) new or proposed headgear impact test procedures in published literature and/or relevant conferences. Research areas identified as needing further knowledge to support standards test development include defining sports-specific head impact conditions, establishing injury and age appropriate headgear assessment criteria, and the development of headgear specific head and neck surrogates for at-risk populations.
ABSTRACT
Traumatic brain injury can lead to the neurodegenerative disease chronic traumatic encephalopathy. This condition has a clear neuropathological definition but the relationship between the initial head impact and the pattern of progressive brain pathology is poorly understood. We test the hypothesis that mechanical strain and strain rate are greatest in sulci, where neuropathology is prominently seen in chronic traumatic encephalopathy, and whether human neuroimaging observations converge with computational predictions. Three distinct types of injury were simulated. Chronic traumatic encephalopathy can occur after sporting injuries, so we studied a helmet-to-helmet impact in an American football game. In addition, we investigated an occipital head impact due to a fall from ground level and a helmeted head impact in a road traffic accident involving a motorcycle and a car. A high fidelity 3D computational model of brain injury biomechanics was developed and the contours of strain and strain rate at the grey matter-white matter boundary were mapped. Diffusion tensor imaging abnormalities in a cohort of 97 traumatic brain injury patients were also mapped at the grey matter-white matter boundary. Fifty-one healthy subjects served as controls. The computational models predicted large strain most prominent at the depths of sulci. The volume fraction of sulcal regions exceeding brain injury thresholds were significantly larger than that of gyral regions. Strain and strain rates were highest for the road traffic accident and sporting injury. Strain was greater in the sulci for all injury types, but strain rate was greater only in the road traffic and sporting injuries. Diffusion tensor imaging showed converging imaging abnormalities within sulcal regions with a significant decrease in fractional anisotropy in the patient group compared to controls within the sulci. Our results show that brain tissue deformation induced by head impact loading is greatest in sulcal locations, where pathology in cases of chronic traumatic encephalopathy is observed. In addition, the nature of initial head loading can have a significant influence on the magnitude and pattern of injury. Clarifying this relationship is key to understanding the long-term effects of head impacts and improving protective strategies, such as helmet design.
Subject(s)
Chronic Traumatic Encephalopathy/pathology , Computer Simulation , Adolescent , Adult , Anisotropy , Chronic Traumatic Encephalopathy/drug therapy , Diffusion Tensor Imaging , Female , Football/injuries , Head/diagnostic imaging , Humans , Imaging, Three-Dimensional , Male , Middle Aged , Models, Neurological , Neuropsychological Tests , Young AdultABSTRACT
This paper investigates the design optimisation of a magnetic field based soft tactile sensor, comprised of a magnet and Hall effect module separated by an elastomer. The aim was to minimise sensitivity of the output force with respect to the input magnetic field; this was achieved by varying the geometry and material properties. Finite element simulations determined the magnetic field and structural behaviour under load. Genetic programming produced phenomenological expressions describing these responses. Optimisation studies constrained by a measurable force and stable loading conditions were conducted; these produced Pareto sets of designs from which the optimal sensor characteristics were selected. The optimisation demonstrated a compromise between sensitivity and the measurable force, a fabricated version of the optimised sensor validated the improvements made using this methodology. The approach presented can be applied in general for optimising soft tactile sensor designs over a range of applications and sensing modes.
ABSTRACT
Tactile sensors are essential if robots are to safely interact with the external world and to dexterously manipulate objects. Current tactile sensors have limitations restricting their use, notably being too fragile or having limited performance. Magnetic field-based soft tactile sensors offer a potential improvement, being durable, low cost, accurate and high bandwidth, but they are relatively undeveloped because of the complexities involved in design and calibration. This paper presents a general design methodology for magnetic field-based three-axis soft tactile sensors, enabling researchers to easily develop specific tactile sensors for a variety of applications. All aspects (design, fabrication, calibration and evaluation) of the development of tri-axis soft tactile sensors are presented and discussed. A moving least square approach is used to decouple and convert the magnetic field signal to force output to eliminate non-linearity and cross-talk effects. A case study of a tactile sensor prototype, MagOne, was developed. This achieved a resolution of 1.42 mN in normal force measurement (0.71 mN in shear force), good output repeatability and has a maximum hysteresis error of 3.4%. These results outperform comparable sensors reported previously, highlighting the efficacy of our methodology for sensor design.
ABSTRACT
Due to religious tenets, Sikh population wear turbans and are exempted from wearing helmets in several countries. However, the extent of protection provided by turbans against head injuries during head impacts remains untested. One aim of this study was to provide the first-series data of turbans' protective performance under impact conditions that are representative of real-world bicycle incidents and compare it with the performance of bicycle helmets. Another aim was to suggest potential ways for improving turban's protective performance. We tested five different turbans, distinguished by two wrapping styles and two fabric materials with a size variation in one of the styles. A Hybrid III headform fitted with the turban was dropped onto a 45 degrees anvil at 6.3 m/s and head accelerations were measured. We found large difference in the performance of different turbans, with up to 59% difference in peak translational acceleration, 85% in peak rotational acceleration, and 45% in peak rotational velocity between the best and worst performing turbans. For the same turban, impact on the left and right sides of the head produced very different head kinematics, showing the effects of turban layering. Compared to unprotected head impacts, turbans considerably reduce head injury metrics. However, turbans produced higher values of peak linear and rotational accelerations in front and left impacts than bicycle helmets, except from one turban which produced lower peak head kinematics values in left impacts. In addition, turbans produced peak rotational velocities comparable with bicycle helmets, except from one turban which produced higher values. The impact locations tested here were covered with thick layers of turbans and they were impacted against flat anvils. Turbans may not provide much protection if impacts occur at regions covered with limited amount of fabric or if the impact is against non-flat anvils, which remain untested. Our analysis shows that turbans can be easily compressed and bottom out creating spikes in the headform's translational acceleration. In addition, the high friction between the turban and anvil surface leads to higher tangential force generating more rotational motion. Hence, in addition to improving the coverage of the head, particularly in the crown and rear locations, we propose two directions for turban improvement: (i) adding deformable materials within the turban layers to increase the impact duration and reduce the risk of bottoming out; (ii) reducing the friction between turban layers to reduce the transmission of rotational motion to the head. Overall, the study assessed Turbans' protection in cyclist head collisions, with a vision that the results of this study can guide further necessary improvements for advanced head protection for the Sikh community.
Subject(s)
Bicycling , Craniocerebral Trauma , Humans , Bicycling/injuries , Craniocerebral Trauma/prevention & control , Mechanical Phenomena , Biomechanical Phenomena , Acceleration , Head Protective Devices , HeadABSTRACT
Head acceleration events (HAEs) are acceleration responses of the head following external short-duration collisions. The potential risk of brain injury from a single high-magnitude HAE or repeated occurrences makes them a significant concern in sport. Instrumented mouthguards (iMGs) can approximate HAEs. The distinction between sensor acceleration events, the iMG datum for approximating HAEs and HAEs themselves, which have been defined as the in vivo event, is made to highlight limitations of approximating HAEs using iMGs. This article explores the technical limitations of iMGs that constrain the approximation of HAEs and discusses important conceptual considerations for stakeholders interpreting iMG data. The approximation of HAEs by sensor acceleration events is constrained by false positives and false negatives. False positives occur when a sensor acceleration event is recorded despite no (in vivo) HAE occurring, while false negatives occur when a sensor acceleration event is not recorded after an (in vivo) HAE has occurred. Various mechanisms contribute to false positives and false negatives. Video verification and post-processing algorithms offer effective means for eradicating most false positives, but mitigation for false negatives is less comprehensive. Consequently, current iMG research is likely to underestimate HAE exposures, especially at lower magnitudes. Future research should aim to mitigate false negatives, while current iMG datasets should be interpreted with consideration for false negatives when inferring athlete HAE exposure.
Subject(s)
Acceleration , Head , Mouth Protectors , Humans , Athletic Injuries/prevention & control , Algorithms , Biomechanical Phenomena , Craniocerebral Trauma/prevention & controlABSTRACT
Head injuries are common for cyclists involved in collisions. Such collision scenarios result in a range of injuries, with different head impact speeds, angles, locations, or surfaces. A clear understanding of these collision characteristics is vital to design high fidelity test methods for evaluating the performance of helmets. We review literature detailing real-world cyclist collision scenarios and report on these key characteristics. Our review shows that helmeted cyclists have a considerable reduction in skull fracture and focal brain pathologies compared to non-helmeted cyclists, as well as a reduction in all brain pathologies. The considerable reduction in focal head pathologies is likely to be due to helmet standards mandating thresholds of linear acceleration. The less considerable reduction in diffuse brain injuries is likely to be due to the lack of monitoring head rotation in test methods. We performed a novel meta-analysis of the location of 1809 head impacts from ten studies. Most studies showed that the side and front regions are frequently impacted, with one large, contemporary study highlighting a high proportion of occipital impacts. Helmets frequently had impact locations low down near the rim line. The face is not well protected by most conventional bicycle helmets. Several papers determine head impact speed and angle from in-depth reconstructions and computer simulations. They report head impact speeds from 5 to 16 m/s, with a concentration around 5 to 8 m/s and higher speeds when there was another vehicle involved in the collision. Reported angles range from 10° to 80° to the normal, and are concentrated around 30°-50°. Our review also shows that in nearly 80% of the cases, the head impact is reported to be against a flat surface. This review highlights current gaps in data, and calls for more research and data to better inform improvements in testing methods of standards and rating schemes and raise helmet safety.
Subject(s)
Bicycling , Craniocerebral Trauma , Humans , Bicycling/injuries , Craniocerebral Trauma/prevention & control , Computer Simulation , Head Protective Devices , Acceleration , Accidents, TrafficABSTRACT
Traumatic brain injury (TBI) is a common injury in the workplace. Trips and falls are the leading causes of TBI in the workplace. However, industrial safety helmets are not designed for protecting the head under these impact conditions. Instead, they are designed to pass the regulatory standards which test head protection against falling heavy and sharp objects. This is likely to be due to the limited understanding of head impact conditions from trips and falls in workplace. In this study, we used validated human multi-body models to predict the head impact location, speed and angle (measured from the ground) during trips, forward falls and backward falls. We studied the effects of worker size, initial posture, walking speed, width and height of the tripping barrier, bracing and falling height on the head impact conditions. Overall, we performed 1692 simulations. The head impact speed was over two folds larger in falls than trips, with backward falls producing highest impact speeds. However, the trips produced impacts with smaller impact angles to the ground. Increasing the walking speed increased the head impact speed but bracing reduced it. We found that 41% of backward falls and 19% of trips/forward falls produced head impacts located outside the region of helmet coverage. Next, we grouped all the data into three sub-groups based on the head impact angle: [0°, 30°], (30°, 60°] and (60°, 90°] and excluded groups with small number of cases. We found that most trips and forward falls lead to impact angles within the (30°, 60°] and (60°, 90°] groups while all backward falls produced impact angles within (60°, 90°] group. We therefore determined five representative head impact conditions from these groups by selecting the 75th percentile speed, mean value of angle intervals and median impact location (determined by elevation and azimuth angles) of each group. This led to two representative head impact conditions for trips: 2.7 m/s at 45° and 3.9 m/s at 75°, two for forward falls: 3.8 m/s at 45° and 5.5 m/s at 75° and one for backward falls: 9.4 m/s at 75°. These impact conditions can be used to improve industrial helmet standards.
ABSTRACT
Traumatic brain injury (TBI) is a prevalent injury among cyclists experiencing head collisions. In legal cases, reliable brain injury evaluation can be difficult and controversial as mild injuries cannot be diagnosed with conventional brain imaging methods. In such cases, accident reconstruction may be used to predict the risk of TBI. However, lack of collision details can render accident reconstruction nearly impossible. Here, we introduce a reconstruction method to evaluate the brain injury in a bicycle-vehicle collision using the crash helmet alone. Following a thorough inspection of the cyclist's helmet, we identified a severe impact, a moderate impact and several scrapes, which helped us to determine the impact conditions. We used our helmet test rig and intact helmets identical to the cyclist's helmet to replicate the damage seen on the cyclist's helmet involved in the real-world collision. We performed both linear and oblique impacts, measured the translational and rotational kinematics of the head and predicted the strain and the strain rate across the brain using a computational head model. Our results proved the hypothesis that the cyclist sustained a severe impact followed by a moderate impact on the road surface. The estimated head accelerations and velocity (167 g, 40.7 rad/s and 13.2 krad/s2) and the brain strain and strain rate (0.541 and 415/s) confirmed that the severe impact was large enough to produce mild to moderate TBI. The method introduced in this study can guide future accident reconstructions, allowing for the evaluation of TBI using the crash helmet only.
ABSTRACT
Tissue examination by hand remains an essential technique in clinical practice. The effective application depends on skills in sensorimotor coordination, mainly involving haptic, visual, and auditory feedback. The skills clinicians have to learn can be as subtle as regulating finger pressure with breathing, choosing palpation action, monitoring involuntary facial and vocal expressions in response to palpation, and using pain expressions both as a source of information and as a constraint on physical examination. Patient simulators can provide a safe learning platform to novice physicians before trying real patients. This paper reviews state-of-the-art medical simulators for the training for the first time with a consideration of providing multimodal feedback to learn as many manual examination techniques as possible. The study summarizes current advances in tissue examination training devices simulating different medical conditions and providing different types of feedback modalities. Opportunities with the development of pain expression, tissue modeling, actuation, and sensing are also analyzed to support the future design of effective tissue examination simulators.
Subject(s)
Robotic Surgical Procedures , Robotics , Humans , Feedback, Sensory , Feedback , Palpation/methods , Computer SimulationABSTRACT
The current combat helmets are primarily designed to mitigate blunt impacts and ballistic loadings. Their protection against primary blast wave is not well studied. In this paper, we comprehensively assessed the protective capabilities of the advanced combat helmet and goggles against blast waves with different intensity and directions. Using a high-fidelity human head model, we compared the intracranial pressure (ICP), cerebrospinal fluid (CSF) cavitation, and brain strain and strain rate predicted from bare head, helmet-head and helmet-goggles-head simulations. The helmet was found to be effective in mitigating the positive ICP (24-57%) and strain rate (5-34%) in all blast scenarios. Goggles were found to be effective in mitigating the positive ICP in frontal (6-16%) and lateral (5-7%) blast exposures. However, the helmet and goggles had minimal effects on mitigating CSF cavitation and even increased brain strain. Further investigation showed that wearing a helmet leads to higher risk of cavitation. In addition, their presence increased the head kinetic energy, leading to larger strains in the brain. Our findings can improve our understanding of the protective effects of helmets and goggles and guide the design of helmet pads to mitigate brain responses to blast.
Subject(s)
Blast Injuries , Head Protective Devices , Humans , Eye Protective Devices , Blast Injuries/prevention & control , Computer Simulation , Biomechanical Phenomena , Brain/physiologyABSTRACT
E-scooters are the fastest growing mode of micro-mobility with important environmental benefits. However, there are serious concerns about injuries caused by e-scooter accidents. Falls due to poor road surface conditions are a common cause of injury in e-scooter riders, and head injuries are one of the most common and concerning injuries in e-scooter falls. However, the head-ground impact biomechanics in e-scooter falls and its relationship with e-scooter speed and design, road surface conditions and wearing helmets remain poorly understood. To address some of these key questions, we predicted the head-ground impact force and velocity of e-scooter riders in different falls caused by potholes. We used multi-body dynamics approach to model a commercially available e-scooter and simulate 180 falls using human body models. We modelled different pothole sizes to test whether the pothole width and depth influences the onset of falls and head-ground impact velocity and force. We also tested whether the e-scooter travelling speed has an influence on the head-ground impact velocity and force. The simulations were carried out with three human body models to ensure that the results of the study are inclusive of a wide range of rider sizes. For our 10 in. diameter e-scooter wheels, we found a sudden increase in the occurrence of falls when the pothole depth was increased from 3 cm (no falls) to 6 cm (41 falls out of 60 cases). When the falls occurred, we found a head-ground impact force of 13.2 ± 3.4kN, which is larger than skull fracture thresholds. The head-ground impact speed was 6.3 ± 1.4 m/s, which is the same as the impact speed prescribed in bicycle helmet standards. All e-scooter falls resulted in oblique head impacts, with an impact angle of 65 ± 10° (measured from the ground). Decreasing the e-scooter speed reduced the head impact speed. For instance, reducing the e-scooter speed from 30 km/h to 20 km/h led to a 14% reduction in the mean impact speed and 12% reduction in the mean impact force, as predicted by the models. The models also showed that the median male riders were sustaining higher head-ground impact force and speed compared with the small female and large male riders. The findings of this study can assist authorities and e-scooter hiring companies to take more informed actions about road surface conditions and speed limits. These results can also help define representative impact test conditions for assessing the performance of helmets used by e-scooter riders in order to reduce head and brain injuries in e-scooter falls.
Subject(s)
Accidental Falls , Craniocerebral Trauma , Accidents, Traffic , Biomechanical Phenomena , Craniocerebral Trauma/prevention & control , Female , Head Protective Devices , Humans , MaleABSTRACT
New oblique impact methods for evaluating head injury mitigation effects of helmets are emerging, which mandate measuring both translational and rotational kinematics of the headform. These methods need headforms with biofidelic mass, moments of inertia (MoIs), and coefficient of friction (CoF). To fulfill this need, working group 11 of the European standardization head protection committee (CEN/TC158) has been working on the development of a new headform with realistic MoIs and CoF, based on recent biomechanics research on the human head. In this study, we used a version of this headform (Cellbond) to test a motorcycle helmet under the oblique impact at 8 m/s at five different locations. We also used the Hybrid III headform, which is commonly used in the helmet oblique impact. We tested whether there is a difference between the predictions of the headforms in terms of injury metrics based on head kinematics, including peak translational and rotational acceleration, peak rotational velocity, and BrIC (brain injury criterion). We also used the Imperial College finite element model of the human head to predict the strain and strain rate across the brain and tested whether there is a difference between the headforms in terms of the predicted strain and strain rate. We found that the Cellbond headform produced similar or higher peak translational accelerations depending on the impact location (-3.2% in the front-side impact to 24.3% in the rear impact). The Cellbond headform, however, produced significantly lower peak rotational acceleration (-41.8% in a rear impact to -62.7% in a side impact), peak rotational velocity (-29.5% in a side impact to -47.6% in a rear impact), and BrIC (-29% in a rear-side impact to -45.3% in a rear impact). The 90th percentile values of the maximum brain strain and strain rate were also significantly lower using this headform. Our results suggest that MoIs and CoF have significant effects on headform rotational kinematics, and consequently brain deformation, during the helmeted oblique impact. Future helmet standards and rating methods should use headforms with realistic MoIs and CoF (e.g., the Cellbond headform) to ensure more accurate representation of the head in laboratory impact tests.
ABSTRACT
Cerebrospinal fluid (CSF) cavitation is a likely physical mechanism for producing traumatic brain injury (TBI) under mechanical loading. In this study, we investigated CSF cavitation under blasts and helmeted impacts which represented loadings in battlefield and road traffic/sports collisions. We first predicted the human head response under the blasts and impacts using computational modelling and found that the blasts can produce much lower negative pressure at the contrecoup CSF region than the impacts. Further analysis showed that the pressure waves transmitting through the skull and soft tissue are responsible for producing the negative pressure at the contrecoup region. Based on this mechanism, we hypothesised that blast, and not impact, can produce CSF cavitation. To test this hypothesis, we developed a one-dimensional simplified surrogate model of the head and exposed it to both blasts and impacts. The test results confirmed the hypothesis and computational modelling of the tests validated the proposed mechanism. These findings have important implications for prevention and diagnosis of blast TBI.
ABSTRACT
Road traffic collisions are a major cause of traumatic brain injury. However, the relationship between road traffic collision dynamics and traumatic brain injury risk for different road users is unknown. We investigated 2065 collisions from Great Britain's Road Accident In-depth Studies collision database involving 5374 subjects (2013-20). Five hundred and ninety-five subjects sustained a traumatic brain injury (20.2% of 2940 casualties), including 315 moderate-severe and 133 mild-probable injuries. Key pathologies included skull fracture (179, 31.9%), subarachnoid haemorrhage (171, 30.5%), focal brain injury (168, 29.9%) and subdural haematoma (96, 17.1%). These results were extended nationally using >1 000 000 police-reported collision casualties. Extrapolating from the in-depth data we estimate that there are â¼20 000 traumatic brain injury casualties (â¼5000 moderate-severe) annually on Great Britain's roads, accounting for severity differences. Detailed collision investigation allows vehicle collision dynamics to be understood and the change in velocity (known as delta-V) to be estimated for a subset of in-depth collision data. Higher delta-V increased the risk of moderate-severe brain injury for all road users. The four key pathologies were not observed below 8â km/h delta-V for pedestrians/cyclists and 19â km/h delta-V for car occupants (higher delta-V threshold for focal injury in both groups). Traumatic brain injury risk depended on road user type, delta-V and impact direction. Accounting for delta-V, pedestrians/cyclists had a 6-times higher likelihood of moderate-severe brain injury than car occupants. Wearing a cycle helmet during a collision was protective against overall and mild-to-moderate-to-severe brain injury, particularly skull fracture and subdural haematoma. Cycle helmet protection was not due to travel or impact speed differences between helmeted and non-helmeted cyclist groups. We additionally examined the influence of the delta-V direction. Car occupants exposed to a higher lateral delta-V component had a greater prevalence of moderate-severe brain injury, particularly subarachnoid haemorrhage. Multivariate logistic regression models created using total delta-V value and whether lateral delta-V was dominant had the best prediction capabilities (area under the receiver operator curve as high as 0.95). Collision notification systems are routinely fitted in new cars. These record delta-V and automatically alert emergency services to a collision in real-time. These risk relationships could, therefore, inform how routinely fitted automatic collision notification systems alert the emergency services to collisions with a high brain injury risk. Early notification of high-risk scenarios would enable quicker activation of the highest level of emergency service response. Identifying those that require neurosurgical care and ensuring they are transported directly to a centre with neuro-specialist provisions could improve patient outcomes.
ABSTRACT
Finite Element (FE) models of brain mechanics have improved our understanding of the brain response to rapid mechanical loads that produce traumatic brain injuries. However, these models have rarely incorporated vasculature, which limits their ability to predict the response of vessels to head impacts. To address this shortcoming, here we used high-resolution MRI scans to map the venous system anatomy at a submillimetre resolution. We then used this map to develop an FE model of veins and incorporated it in an anatomically detailed FE model of the brain. The model prediction of brain displacement at different locations was compared to controlled experiments on post-mortem human subject heads, yielding over 3,100 displacement curve comparisons, which showed fair to excellent correlation between them. We then used the model to predict the distribution of axial strains and strain rates in the veins of a rugby player who had small blood deposits in his white matter, known as microbleeds, after sustaining a head collision. We hypothesised that the distribution of axial strain and strain rate in veins can predict the pattern of microbleeds. We reconstructed the head collision using video footage and multi-body dynamics modelling and used the predicted head accelerations to load the FE model of vascular injury. The model predicted large axial strains in veins where microbleeds were detected. A region of interest analysis using white matter tracts showed that the tract group with microbleeds had 95th percentile peak axial strain and strain rate of 0.197 and 64.9 s-1 respectively, which were significantly larger than those of the group of tracts without microbleeds (0.163 and 57.0 s-1). This study does not derive a threshold for the onset of microbleeds as it investigated a single case, but it provides evidence for a link between strain and strain rate applied to veins during head impacts and structural damage and allows for future work to generate threshold values. Moreover, our results suggest that the FE model has the potential to be used to predict intracranial vascular injuries after TBI, providing a more objective tool for TBI assessment and improving protection against it.
ABSTRACT
Motorcyclists are at high risk of head injuries, including skull fractures, focal brain injuries, intracranial bleeding and diffuse brain injuries. New helmet technologies have been developed to mitigate head injuries in motorcycle collisions, but there is limited information on their performance under commonly occurring oblique impacts. We used an oblique impact method to assess the performance of seven modern motorcycle helmets at five impact locations. Four helmets were fitted with rotational management technologies: a low friction layer (MIPS), three-layer liner system (Flex) and dampers-connected liner system (ODS). Helmets were dropped onto a 45° anvil at 8 m/s at five locations. We determined peak translational and rotational accelerations (PTA and PRA), peak rotational velocity (PRV) and brain injury criteria (BrIC). In addition, we used a human head finite element model to predict strain distribution across the brain and in corpus callosum and sulci. We found that the impact location affected the injury metrics and brain strain, but this effect was not consistent. The rear impact produced lowest PTAs but highest PRAs. This impact produced highest strain in corpus callosum. The front impact produced the highest PRV and BrIC. The side impact produced the lowest PRV, BrIC and strain across the brain, sulci and corpus callosum. Among helmet technologies, MIPS reduced all injury metrics and brain strain compared with conventional helmets. Flex however was effective in reducing PRA only and ODS was not effective in reducing any injury metrics in comparison with conventional helmets. This study shows the importance of using different impact locations and injury metrics when assessing head protection effects of helmets. It also provides new data on the performance of modern motorcycle helmets. These results can help with improving helmet design and standard and rating test methods.