ABSTRACT
Two-dimensional (2D) transition metal dichalcogenide (TMD) layers are highly promising as field-effect transistor (FET) channels in the atomic-scale limit. However, accomplishing this superiority in scaled-up FETs remains challenging due to their van der Waals (vdW) bonding nature with respect to conventional metal electrodes. Herein, we report a scalable approach to fabricate centimeter-scale all-2D FET arrays of platinum diselenide (PtSe2) with in-plane platinum ditelluride (PtTe2) edge contacts, mitigating the aforementioned challenges. We realized a reversible transition between semiconducting PtSe2 and metallic PtTe2 via a low-temperature anion exchange reaction compatible with the back-end-of-line (BEOL) processes. All-2D PtSe2 FETs seamlessly edge-contacted with transited metallic PtTe2 exhibited significant performance improvements compared to those with surface-contacted gold electrodes, e.g., an increase of carrier mobility and on/off ratio by over an order of magnitude, achieving a maximum hole mobility of â¼50.30 cm2 V-1 s-1 at room temperature. This study opens up new opportunities toward atomically thin 2D-TMD-based circuitries with extraordinary functionalities.
ABSTRACT
Crystallographically anisotropic two-dimensional (2D) molybdenum disulfide (MoS2) with vertically aligned (VA) layers is attractive for electrochemical sensing owing to its surface-enriched dangling bonds coupled with extremely large mechanical deformability. In this study, we explored VA-2D MoS2layers integrated on cellulose nanofibers (CNFs) for detecting various volatile organic compound gases. Sensor devices employing VA-2D MoS2/CNFs exhibited excellent sensitivities for the tested gases of ethanol, methanol, ammonia, and acetone; e.g. a high response rate up to 83.39% for 100 ppm ethanol, significantly outperforming previously reported sensors employing horizontally aligned 2D MoS2layers. Furthermore, VA-2D MoS2/CNFs were identified to be completely dissolvable in buffer solutions such as phosphate-buffered saline solution and baking soda buffer solution without releasing toxic chemicals. This unusual combination of high sensitivity and excellent biodegradability inherent to VA-2D MoS2/CNFs offers unprecedented opportunities for exploring mechanically reconfigurable sensor technologies with bio-compatible transient characteristics.
ABSTRACT
We report a novel strategy to assemble wafer-scale two-dimensional (2D) transition metal dichalcogenide (TMD) layers of well-defined components and orientations. We directly grew a variety of 2D TMD layers on "water-dissoluble" single-crystalline salt wafers and precisely delaminated them inside water in a chemically benign manner. This manufacturing strategy enables the automated integration of vertically aligned 2D TMD layers as well as 2D/2D heterolayers of arbitrary stacking orders on exotic substrates insensitive to their kind and shape. Furthermore, the original salt wafers can be recycled for additional growths, confirming high process sustainability and scalability. The generality and versatility of this approach have been demonstrated by developing proof-of-concept "all 2D" devices for diverse yet unconventional applications. This study is believed to shed a light on leveraging opportunities of 2D TMD layers toward achieving large-area mechanically reconfigurable devices of various form factors at the industrially demanded scale.
ABSTRACT
A globally imminent shortage of freshwater has been demanding viable strategies for improving desalination efficiencies with the adoption of cost- and energy-efficient membrane materials. The recently explored 2D transition metal dichalcogenides (2D TMDs) of near atomic thickness have been envisioned to offer notable advantages as high-efficiency membranes owing to their structural uniqueness; that is, extremely small thickness and intrinsic atomic porosity. Despite theoretically projected advantages, experimental realization of near atom-thickness 2D TMD-based membranes and their desalination efficiency assessments have remained largely unexplored mainly due to the technical difficulty associated with their seamless large-scale integration. Herein, we report the experimental demonstration of high-efficiency water desalination membranes based on few-layer 2D molybdenum disulfide (MoS2) of only â¼7 nm thickness. Chemical vapor deposition (CVD)-grown centimeter-scale 2D MoS2 layers were integrated onto porous polymeric supports with well-preserved structural integrity enabled by a water-assisted 2D layer transfer method. These 2D MoS2 membranes of near atomic thickness exhibit an excellent combination of high water permeability (>322 L m-2 h-1 bar-1) and high ionic sieving capability (>99%) for various seawater salts including Na+, K+, Ca2+, and Mg2+ with a range of concentrations. Moreover, they present near 100% salt ion rejection rates for actual seawater obtained from the Atlantic coast, significantly outperforming the previously developed 2D MoS2 layer membranes of micrometer thickness as well as conventional reverse osmosis (RO) membranes. Underlying principles behind such remarkably excellent desalination performances are attributed to the intrinsic atomic vacancies inherent to the CVD-grown 2D MoS2 layers as verified by aberration-corrected electron microscopy characterization.
ABSTRACT
Two-dimensional transition-metal dichalcogenide (2D TMD) layers are highly attractive for emerging stretchable and foldable electronics owing to their extremely small thickness coupled with extraordinary electrical and optical properties. Although intrinsically large strain limits are projected in them (i.e., several times greater than silicon), integrating 2D TMDs in their pristine forms does not realize superior mechanical tolerance greatly demanded in high-end stretchable and foldable devices of unconventional form factors. In this article, we report a versatile and rational strategy to convert 2D TMDs of limited mechanical tolerance to tailored 3D structures with extremely large mechanical stretchability accompanying well-preserved electrical integrity and modulated transport properties. We employed a concept of strain engineering inspired by an ancient paper-cutting art, known as kirigami patterning, and developed 2D TMD-based kirigami electrical conductors. Specifically, we directly integrated 2D platinum diselenide (2D PtSe2) layers of controlled carrier transport characteristics on mechanically flexible polyimide (PI) substrates by taking advantage of their low synthesis temperature. The metallic 2D PtSe2/PI kirigami patterns of optimized dimensions exhibit an extremely large stretchability of â¼2000% without compromising their intrinsic electrical conductance. They also present strain-tunable and reversible photoresponsiveness when interfaced with semiconducting carbon nanotubes (CNTs), benefiting from the formation of 2D PtSe2/CNT Schottky junctions. Moreover, kirigami field-effect transistors (FETs) employing semiconducting 2D PtSe2 layers exhibit tunable gate responses coupled with mechanical stretching upon electrolyte gating. The exclusive role of the kirigami pattern parameters in the resulting mechanoelectrical responses was also verified by a finite-element modeling (FEM) simulation. These multifunctional 2D materials in unconventional yet tailored 3D forms are believed to offer vast opportunities for emerging electronics and optoelectronics.
ABSTRACT
A novel nano-scale manipulator capable of handling low-dimensional materials with three-dimensional linear motion, gripping action, and push-pull action of the gripper was developed for an in situ experiment in transmission electron microscopy. X-Y-Z positioning and push-pull action were accomplished by a piezotubing system, combined with a specially designed assembly stage that consisted of a lever-action gripping tip backed by a push-pull piezostack. The gripper tip consisted of tungsten wire fabricated by electrochemical etching followed by a focused ion beam process. Performance of the nano-scale manipulator was demonstrated in a grab-and-pick test of a single silver nanowire and in an in situ tensile test of a pearlitic steel sample with a specific orientation.
ABSTRACT
Transient electronics technology has enabled the programmed disintegration of functional devices, paving the way for environmentally sustainable management of electronic wastes as well as facilitating the exploration of novel device concepts. While a variety of inorganic and/or organic materials have been employed as media to introduce transient characteristics in electronic devices, they have been mainly limited to function as passive device components. Herein, we report that calcium (Ca) alginate, a natural biopolymer, exhibits multifunctionalities of introducing light-triggered transient characteristics as well as constituting active components in electronic devices integrated with two-dimensional (2D) molybdenum disulfide (MoS2) layers. Ca2+ ions-based alginate electrolyte films are prepared through hydrolysis reactions and are subsequently incorporated with riboflavin, a natural photosensitizer, for the light-driven dissolution of 2D MoS2 layers. The alginate films exhibit strain-sensitive triboelectricity, confirming the presence of abundant mobile Ca2+ ions, which enables them to be active components of 2D MoS2 field-effect transistors (FETs) functioning as electrolyte top-gates. The alginate-integrated 2D MoS2 FETs display intriguing transient characteristics of spontaneous degradation upon ultraviolet-to-visible light illumination as well as water exposure. Such transient characteristics are demonstrated even in ambient conditions with natural sunlight, highlighting the versatility of the developed approach. This study emphasizes a relatively unexplored aspect of combining naturally abundant polymers with emerging near atom-thickness semiconductors toward realizing unconventional and transformative device functionalities.
ABSTRACT
Prevailing over the bottleneck of von Neumann computing has been significant attention due to the inevitableness of proceeding through enormous data volumes in current digital technologies. Inspired by the human brain's operational principle, the artificial synapse of neuromorphic computing has been explored as an emerging solution. Especially, the optoelectronic synapse is of growing interest as vision is an essential source of information in which dealing with optical stimuli is vital. Herein, flexible optoelectronic synaptic devices composed of centimeter-scale tellurium dioxide (TeO2) films detecting and exhibiting synaptic characteristics to broadband wavelengths are presented. The TeO2-based flexible devices demonstrate a comprehensive set of emulating basic optoelectronic synaptic characteristics; i.e., excitatory postsynaptic current (EPSC), paired-pulse facilitation (PPF), conversion of short-term to long-term memory, and learning/forgetting. Furthermore, they feature linear and symmetric conductance synaptic weight updates at various wavelengths, which are applicable to broadband neuromorphic computations. Based on this large set of synaptic attributes, a variety of applications such as logistic functions or deep learning and image recognition as well as learning simulations are demonstrated. This work proposes a significant milestone of wafer-scale metal oxide semiconductor-based artificial synapses solely utilizing their optoelectronic features and mechanical flexibility, which is attractive toward scaled-up neuromorphic architectures.
ABSTRACT
Electronic devices employing two-dimensional (2D) van der Waals (vdW) transition-metal dichalcogenide (TMD) layers as semiconducting channels often exhibit limited performance (e.g., low carrier mobility), in part, due to their high contact resistances caused by interfacing non-vdW three-dimensional (3D) metal electrodes. Herein, we report that this intrinsic contact issue can be efficiently mitigated by forming the 2D/2D in-plane junctions of 2D semiconductor channels seamlessly interfaced with 2D metal electrodes. For this, we demonstrated the selectively patterned conversion of semiconducting 2D PtSe2 (channels) to metallic 2D PtTe2 (electrodes) layers by employing a wafer-scale low-temperature chemical vapor deposition (CVD) process. We investigated a variety of field-effect transistors (FETs) employing wafer-scale CVD-2D PtSe2/2D PtTe2 heterolayers and identified that silicon dioxide (SiO2) top-gated FETs exhibited an extremely high hole mobility of â¼120 cm2 V-1 s-1 at room temperature, significantly surpassing performances with previous wafer-scale 2D PtSe2-based FETs. The low-temperature nature of the CVD method further allowed for the direct fabrication of wafer-scale arrays of 2D PtSe2/2D PtTe2 heterolayers on polyamide (PI) substrates, which intrinsically displayed optical pulse-induced artificial synaptic behaviors. This study is believed to vastly broaden the applicability of 2D TMD layers for next-generation, high-performance electronic devices with unconventional functionalities.
ABSTRACT
Phytoplasmas were discovered in diseased Elaeocarpus sylvestris trees growing on Jeju Island that showed symptoms of yellowing and darkening in the leaves. Leaf samples from 14 symptomatic plants in Jeju-si and Seogwipo-si were collected and phytoplasma 16S rRNA was successfully amplified by nested polymerase chain reaction using universal primers. The sequence analysis detected two phytoplasmas, which showed 99.5% identity to 'Candidatus Phytoplasma asteris' and 'Ca. P. malaysianum' affiliated to 16SrI and 16SrXXXII groups, respectively. Through polymerase chain reaction-restriction fragment length polymorphism (RFLP) analyses using the AfaI (RsaI) restriction enzyme, the presence of two phytoplasmas strains as well as cases of mixed infection of these strains was detected. In a virtual RFLP analysis with 17 restriction enzymes, the 16S rRNA sequence of the 'Ca. P. asteris' strain was found to match the pattern of the 16SrI-B subgroup. In addition, the phytoplasmas in the mixed-infection cases could be distinguished using specific primer sets. In conclusion, this study confirmed mixed infection of two phytoplasmas in one E. sylvestris plant, and also the presence of two phytoplasmas (of the 16Srâ and 16SrXXXâ ¡ groups) in Jeju Island (Republic of Korea).
ABSTRACT
Tin monosulfide (SnS) is a promising piezoelectric material with an intrinsically layered structure, making it attractive for self-powered wearable and stretchable devices. However, for practical application purposes, it is essential to improve the output and manufacturing compatibility of SnS-based piezoelectric devices by exploring their large-area synthesis principle. In this study, we report the chemical vapor deposition (CVD) growth of centimeter-scale two-dimensional (2D) SnS layers at temperatures as low as 200 °C, allowing compatibility with processing a range of polymeric substrates. The intrinsic piezoelectricity of 2D SnS layers directly grown on polyamides (PIs) was confirmed by piezoelectric force microscopy (PFM) phase maps and force-current corroborative measurements. Furthermore, the structural robustness of the centimeter-scale 2D SnS layers/PIs allowed for engraving complicated kirigami patterns on them. The kirigami-patterned 2D SnS layer devices exhibited intriguing strain-tolerant piezoelectricity, which was employed in detecting human body motions and generating photocurrents irrespective of strain rate variations. These results establish the great promise of 2D SnS layers for practically relevant large-scale device technologies with coupled electrical and mechanical properties.
ABSTRACT
Brain-inspired computing enabled by memristors has gained prominence over the years due to the nanoscale footprint and reduced complexity for implementing synapses and neurons. The demonstration of complex neuromorphic circuits using conventional materials systems has been limited by high cycle-to-cycle and device-to-device variability. Two-dimensional (2D) materials have been used to realize transparent, flexible, ultra-thin memristive synapses for neuromorphic computing, but with limited knowledge on the statistical variation of devices. In this work, we demonstrate ultra-low-variability synapses using chemical vapor deposited 2D MoS2 as the switching medium with Ti/Au electrodes. These devices, fabricated using a transfer-free process, exhibit ultra-low variability in SET voltage, RESET power distribution, and synaptic weight update characteristics. This ultra-low variability is enabled by the interface rendered by a Ti/Au top contact on Si-rich MoS2 layers of mixed orientation, corroborated by transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), and X-ray photoelectron spectroscopy (XPS). TEM images further confirm the stability of the device stack even after subjecting the device to 100 SET-RESET cycles. Additionally, we implement logic gates by monolithic integration of MoS2 synapses with MoS2 leaky integrate-and-fire neurons to show the viability of these devices for non-von Neumann computing.
Subject(s)
Molybdenum , Synapses , Brain , Neurons/physiology , Synapses/physiologyABSTRACT
Neuromorphic visual systems emulating biological retina functionalities have enormous potential for in-sensor computing, with prospects of making artificial intelligence ubiquitous. Conventionally, visual information is captured by an image sensor, stored by memory units, and eventually processed by the machine learning algorithm. Here, we present an optoelectronic synapse device with multifunctional integration of all the processes required for real time object identification. Ultraviolet-visible wavelength-sensitive MoS2 FET channel with infrared sensitive PtTe2/Si gate electrode enables the device to sense, store, and process optical data for a wide range of the electromagnetic spectrum, while maintaining a low dark current. The device exhibits optical stimulation-controlled short-term and long-term potentiation, electrically driven long-term depression, synaptic weight update for multiple wavelengths of light ranging from 300 nm in ultraviolet to 2 µm in infrared. An artificial neural network developed using the extracted weight update parameters of the device can be trained to identify both single wavelength and mixed wavelength patterns. This work demonstrates a device that could potentially be used for realizing a multiwavelength neuromorphic visual system for pattern recognition and object identification.
Subject(s)
Artificial Intelligence , Synapses , Neural Networks, Computer , Algorithms , Neuronal PlasticityABSTRACT
Various near-atom-thickness two-dimensional (2D) van der Waals (vdW) crystals with unparalleled electromechanical properties have been explored for transformative devices. Currently, the availability of 2D vdW crystals is rather limited in nature as they are only obtained from certain mother crystals with intrinsically possessed layered crystallinity and anisotropic molecular bonding. Recent efforts to transform conventionally non-vdW three-dimensional (3D) crystals into ultrathin 2D-like structures have seen rapid developments to explore device building blocks of unique form factors. Herein, we explore a "peel-and-stick" approach, where a nonlayered 3D platinum sulfide (PtS) crystal, traditionally known as a cooperate mineral material, is transformed into a freestanding 2D-like membrane for electromechanical applications. The ultrathin (â¼10 nm) 3D PtS films grown on large-area (>cm2) silicon dioxide/silicon (SiO2/Si) wafers are precisely "peeled" inside water retaining desired geometries via a capillary-force-driven surface wettability control. Subsequently, they are "sticked" on strain-engineered patterned substrates presenting prominent semiconducting properties, i.e., p-type transport with an optical band gap of â¼1.24 eV. A variety of mechanically deformable strain-invariant electronic devices have been demonstrated by this peel-and-stick method, including biaxially stretchable photodetectors and respiratory sensing face masks. This study offers new opportunities of 2D-like nonlayered semiconducting crystals for emerging mechanically reconfigurable and stretchable device technologies.
ABSTRACT
Two-dimensional (2D) molybdenum disulfide (MoS2) layers are suitable for visible-to-near infrared photodetection owing to their tunable optical bandgaps. Also, their superior mechanical deformability enabled by an extremely small thickness and van der Waals (vdW) assembly allows them to be structured into unconventional physical forms, unattainable with any other materials. Herein, we demonstrate a new type of 2D MoS2 layer-based rollable photodetector that can be mechanically reconfigured while maintaining excellent geometry-invariant photo-responsiveness. Large-area (>a few cm2) 2D MoS2 layers grown by chemical vapor deposition (CVD) were integrated on transparent and flexible substrates composed of 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-oxidized cellulose nanofibers (TOCNs) by a direct solution casting method. These composite materials in three-dimensionally rollable forms exhibited a large set of intriguing photo-responsiveness, well preserving intrinsic opto-electrical characteristics of the integrated 2D MoS2 layers; i.e., light intensity-dependent photocurrents insensitive to illumination angles as well as highly tunable photocurrents varying with the rolling number of 2D MoS2 layers, which were impossible to achieve with conventional photodetectors. This study provides a new design principle for converting 2D materials to three-dimensional (3D) objects of tailored functionalities and structures, significantly broadening their potential and versatility in futuristic devices.
ABSTRACT
Two-dimensional (2D) transition metal dichalcogenide (TMD) layers have gained increasing attention for a variety of emerging electrical, thermal, and optical applications. Recently developed metallic 2D TMD layers have been projected to exhibit unique attributes unattainable in their semiconducting counterparts; e.g., much higher electrical and thermal conductivities coupled with mechanical flexibility. In this work, we explored 2D platinum ditelluride (2D PtTe2) layers - a relatively new class of metallic 2D TMDs - by studying their previously unexplored electro-thermal properties for unconventional window applications. We prepared wafer-scale 2D PtTe2 layer-coated optically transparent and mechanically flexible willow glasses via a thermally-assisted tellurization of Pt films at a low temperature of 400 °C. The 2D PtTe2 layer-coated windows exhibited a thickness-dependent optical transparency and electrical conductivity of >106 S m-1 - higher than most of the previously explored 2D TMDs. Upon the application of electrical bias, these windows displayed a significant increase in temperature driven by Joule heating as confirmed by the infrared (IR) imaging characterization. Such superior electro-thermal conversion efficiencies inherent to 2D PtTe2 layers were utilized to demonstrate various applications, including thermochromic displays and electrically-driven defogging windows accompanying mechanical flexibility. Comparisons of these performances confirm the superiority of the wafer-scale 2D PtTe2 layers over other nanomaterials explored for such applications.
ABSTRACT
Two-dimensional (2D) molybdenum disulfide (MoS2) with vertically aligned (VA) layers exhibits significantly enriched surface-exposed edge sites with an abundance of dangling bonds owing to its intrinsic crystallographic anisotropy. Such structural variation renders the material with exceptionally high chemical reactivity and chemisorption ability, making it particularly attractive for high-performance electrochemical sensing. This superior property can be further promoted as far as it is integrated on mechanically stretchable substrates well retaining its surface-exposed defective edges, projecting opportunities for a wide range of applications utilizing its structural uniqueness and mechanical flexibility. In this work, we explored VA-2D MoS2 layers configured in laterally stretchable forms for multifunctional nitrogen dioxide (NO2) gas sensors. Large-area (>cm2) VA-2D MoS2 layers grown by a chemical vapor deposition (CVD) method were directly integrated onto a variety of flexible substrates with serpentine patterns judiciously designed to accommodate a large degree of tensile strain. These uniquely structured VA-2D MoS2 layers were demonstrated to be highly sensitive to NO2 gas of controlled concentration preserving their intrinsic structural and chemical integrity, e.g., significant current response ratios of â¼160-380% upon the introduction of NO2 at a level of 5-30 ppm. Remarkably, they exhibited such a high sensitivity even under lateral stretching up to 40% strain, significantly outperforming previously reported 2D MoS2 layer-based NO2 gas sensors of any structural forms. Underlying principles for the experimentally observed superiority were theoretically unveiled by density functional theory (DFT) calculation and finite element method (FEM) analysis. The intrinsic high sensitivity and large stretchability of VA-2D MoS2 layers confirmed in this study are believed to be applicable in sensing diverse gas species, greatly broadening their versatility in stretchable and wearable technologies.
ABSTRACT
We explored the feasibility of wafer-scale two-dimensional (2D) molybdenum disulfide (MoS2) layers toward futuristic environmentally friendly electronics that adopt biodegradable substrates. Large-area (> a few cm2) 2D MoS2 layers grown on silicon dioxide/silicon (SiO2/Si) wafers were delaminated and integrated onto a variety of cellulose-based substrates of various components and shapes in a controlled manner; examples of the substrates include planar papers, cylindrical natural rubbers, and 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibers. The integrated 2D layers were confirmed to well preserve their intrinsic structural and chemical integrity even on such exotic substrates. Proof-of-concept devices employing large-area 2D MoS2 layers/cellulose substrates were demonstrated for a variety of applications, including photodetectors, pressure sensors, and field-effect transistors. Furthermore, we demonstrated the complete "dissolution" of the integrated 2D MoS2 layers in a buffer solution composed of baking soda and deionized water, confirming their environmentally friendly transient characteristics. Moreover, the approaches to delaminate and integrate them do not demand any chemicals except for water, and their original substrates can be recycled for subsequent growths, ensuring excellent chemical benignity and process sustainability.
ABSTRACT
Platinum diselenide (PtSe2) is an emerging class of two-dimensional (2D) transition-metal dichalcogenide (TMD) crystals recently gaining substantial interest, owing to its extraordinary properties absent in conventional 2D TMD layers. Most interestingly, it exhibits a thickness-dependent semiconducting-to-metallic transition, i.e., thick 2D PtSe2 layers, which are intrinsically metallic, become semiconducting with their thickness reduced below a certain point. Realizing both semiconducting and metallic phases within identical 2D PtSe2 layers in a spatially well-controlled manner offers unprecedented opportunities toward atomically thin tailored electronic junctions, unattainable with conventional materials. In this study, beyond this thickness-dependent intrinsic semiconducting-to-metallic transition of 2D PtSe2 layers, we demonstrate that controlled plasma irradiation can "externally" achieve such tunable carrier transports. We grew wafer-scale very thin (a few nm) 2D PtSe2 layers by a chemical vapor deposition (CVD) method and confirmed their intrinsic semiconducting properties. We then irradiated the material with argon (Ar) plasma, which was intended to make it more semiconducting by thickness reduction. Surprisingly, we discovered a reversed transition of semiconducting to metallic, which is opposite to the prediction concerning their intrinsic thickness-dependent carrier transports. Through extensive structural and chemical characterization, we identified that the plasma irradiation introduces a large concentration of near-atomic defects and selenium (Se) vacancies in initially stoichiometric 2D PtSe2 layers. Furthermore, we performed density functional theory (DFT) calculations and clarified that the band-gap energy of such defective 2D PtSe2 layers gradually decreases with increasing defect concentration and dimensions, accompanying a large number of midgap energy states. This corroborative experimental and theoretical study decisively verifies the fundamental mechanism for this externally controlled semiconducting-to-metallic transition in large-area CVD-grown 2D PtSe2 layers, greatly broadening their versatility for futuristic electronics.
ABSTRACT
Two-dimensional (2D) layered materials and their heterostructures have recently been recognized as promising building blocks for futuristic brain-like neuromorphic computing devices. They exhibit unique properties such as near-atomic thickness, dangling-bond-free surfaces, high mechanical robustness, and electrical/optical tunability. Such attributes unattainable with traditional electronic materials are particularly promising for high-performance artificial neurons and synapses, enabling energy-efficient operation, high integration density, and excellent scalability. In this review, diverse 2D materials explored for neuromorphic applications, including graphene, transition metal dichalcogenides, hexagonal boron nitride, and black phosphorous, are comprehensively overviewed. Their promise for neuromorphic applications are fully discussed in terms of material property suitability and device operation principles. Furthermore, up-to-date demonstrations of neuromorphic devices based on 2D materials or their heterostructures are presented. Lastly, the challenges associated with the successful implementation of 2D materials into large-scale devices and their material quality control will be outlined along with the future prospect of these emergent materials.