Structural Dependence of Reductive Defluorination of Linear PFAS Compounds in a UV/Electrochemical System.

Per and polyfluoroalkyl substances (PFAS), legacy chemicals used in firefighting and the manufacturing of many industrial and consumer goods, are widely found in groundwater resources, along with other regulated compounds, such as chlorinated solvents. Due to their strong C-F bonds, these molecules are extremely recalcitrant, requiring advanced treatment methods for effective remediation, with hydrated electrons shown to be able to defluorinated these compounds. A combined photo/electrochemical method has been demonstrated to dramatically increase defluorination rates, where PFAS molecules sorbed onto appropriately functionalized cathodes charged to low cell potentials (-0.58 V vs Ag/AgCl) undergo a transient electron transfer event from the electrode, which "primes" the molecule by reducing the C-F bond strength and enables the bond's dissociation upon the absorption of a hydrated electron. In this work, we explore the impact of headgroup and chain length on the performance of this two-electron process and extend this technique to chlorinated solvents. We use isotopically labeled PFAS molecules to take advantage of the kinetic isotope effect and demonstrate that indeed PFAS defluorination is likely driven by a two-electron process. We also present density functional theory calculations to illustrate that the externally applied potential resulted in an increased rate of electron transfer, which ultimately increased the measured defluorination rate.

Mineral Scale Prevention on Electrically Conducting Membrane Distillation Membranes Using Induced Electrophoretic Mixing.

The growth of mineral crystals on surfaces is a challenge across multiple industrial processes. Membrane-based desalination processes, in particular, are plagued by crystal growth (known as scaling), which restricts the flow of water through the membrane, can cause membrane wetting in membrane distillation, and can lead to the physical destruction of the membrane material. Scaling occurs when supersaturated conditions develop along the membrane surface due to the passage of water through the membrane, a process known as concentration polarization. To reduce scaling, concentration polarization is minimized by encouraging turbulent conditions and by reducing the amount of water recovered from the saline feed. In addition, antiscaling chemicals can be used to reduce the availability of cations. Here, we report on an energy-efficient electrophoretic mixing method capable of nearly eliminating CaSO4 and silicate scaling on electrically conducting membrane distillation (ECMD) membranes. The ECMD membrane material is composed of a percolating layer of carbon nanotubes deposited on porous polypropylene support and cross-linked by poly(vinyl alcohol). The application of low alternating potentials (2 Vpp,1Hz) had a dramatic impact on scale formation, with the impact highly dependent on the frequency of the applied signal, and in the case of silicate, on the pH of the solution.

Field-Induced Redistribution of Surfactants at the Oil/Water Interface Reduces Membrane Fouling on Electrically Conducting Carbon Nanotube UF Membranes.

Membrane-based treatment of oily wastewater remains a significant challenge, particularly under high salinity conditions. The main difficulty associated with this separation process is membrane fouling, mostly caused by wetting and coalescence of emulsified oil droplets on the membrane surface. In this study, electrically conducting carbon nanotube-based ultrafiltration membranes were used to treat an emulsified oil suspension at ionic strengths as high as 100 mM. By tuning the electrical potential applied to the membrane surface, we demonstrate how fouling can be dramatically reduced, even under high salinity conditions. Permeate water quality is shown to improve upon application of a negative potential. Using optical microscopy, we observed dramatic changes in the shape of oil droplets at the membrane/water interface in response to the applied electric potential; this change is associated with a redistribution of charged surfactant molecules at the oil/water interface in response to the external electric field. Specifically, using the membrane as a cathode repels surfactant molecules away from the oil/membrane interface, while anodic conditions lead to increased surfactant concentrations. We speculate that this change in surfactant molecule distribution is responsible for changes in the surface tension of oil droplets at the membrane/water interface, which results in a decrease in oil coalescence and subsequent fouling. The membranes used in this study offer an attractive treatment option when separating emulsified oil from water under high salinity conditions.

Hot-melt extrusion microencapsulation of quercetin for taste-masking.

Besides its poor dissolution rate, the bitterness of quercetin also poses a challenge for further development. Using carnauba wax, shellac or zein as the shell-forming excipient, this work aimed to microencapsulate quercetin by hot-melt extrusion for taste-masking. In comparison with non-encapsulated quercetin, the microencapsulated powders exhibited significantly reduced dissolution in the simulated salivary pH 6.8 medium indicative of their potentially good taste-masking efficiency in the order of zein > carnauba wax > shellac. In vitro bitterness analysis by electronic tongue confirmed the good taste-masking efficiency of the microencapsulated powders. In vitro digestion results showed that carnauba wax and shellac-microencapsulated powders presented comparable dissolution rate with the pure quercetin in pH 1.0 (gastric) and 6.8 (intestine) medium; while zein-microencapsulated powders exhibited a remarkably slower dissolution rate. Crystallinity of quercetin was slightly reduced after microencapsulation while its chemical structure remained unchanged. Hot-melt extrusion microencapsulation could thus be an attractive technique to produce taste-masked bioactive powders.

A reverse-selective ion exchange membrane for the selective transport of phosphates via an outer-sphere complexation-diffusion pathway.

Specific-ion selectivity is a highly desirable feature for the next generation of membranes. However, existing membranes rely on differences in charge, size and hydration energy, which limits their ability to target individual ion species. Here we demonstrate a nanocomposite ion-exchange membrane material that enables a reverse-selective transport mechanism that can selectively pass a single ion species. We demonstrate this transport mechanism with phosphate ions selectively transporting across negatively charged cation exchange membranes. Selective transport is enabled by the in situ growth of hydrous manganese oxide nanoparticles throughout a cation exchange membrane that provide a diffusion pathway via phosphate-specific, reversible outer-sphere interactions. On incorporating the hydrous manganese oxide nanoparticles, the membrane's phosphate flux increased by a factor of 27 over an unmodified cation exchange membrane, and the selectivity of phosphorous over sulfate, nitrate and chloride reaches 47, 100 and 20, respectively. By pairing ion-specific outer-sphere interactions between the target ions and appropriate nanoparticles, these nanocomposite ion-exchange materials can, in principle, achieve selective transport for a range of ions.

Enhanced removal of per- and polyfluoroalkyl substances in complex matrices by polyDADMAC-coated regenerable granular activated carbon.

Granular activated carbon (GAC) has been used to remove per- and polyfluoroalkyl substances (PFASs) from industrial or AFFF-impacted waters, but its effectiveness can be low because adsorption of short-chained PFASs is ineffective and its sites are exhausted rapidly by co-contaminants. To increase adsorption of anionic PFASs on GAC by electrostatic attractions, we modified GAC's surface with the cationic polymer poly diallyldimethylammonium chloride (polyDADMAC) and tested its capacity in complex water matrices containing dissolved salts and humic acid. Amending with concentrations of polyDADMAC as low as 0.00025% enhanced GAC's adsorption capacity for PFASs, even in the presence of competing ions. This suggests that electrostatic interactions with polyDADMAC's quaternary ammonium functional groups helped bind organic and inorganic ions as well as the headgroup of short-chain PFASs, allowing more overall PFAS removal by GAC. Evaluating the effect of polymer dose is important because excessive addition can block pores and reduce overall PFAS removal rather than increase it. To decrease the waste associated with this adsorption strategy by making the adsorbent viable for more than one saturation cycle, a regeneration method is proposed which uses low-power ultrasound to enhance the desorption of PFASs from the polyDADMAC-GAC with minimum disruption to the adsorbent's structure. Re-modification with the polymer after sonication resulted in a negligible decrease in the sorbent's capacity over four saturation rounds. These results support consideration of polyDADMAC-modified GAC as an effective regenerable adsorbent for ex-situ concentration step of both short and long-chain PFASs from real waters with high concentrations of competing ions and low PFAS loads.

Removal of As(III) by Electrically Conducting Ultrafiltration Membranes.

As(III) species are the predominant form of arsenic found in groundwater. However, nanofiltration (NF) and reverse osmosis (RO) membranes are often unable to effectively reject As(III). In this study, we fabricate highly conducting ultrafiltration (UF) membranes for effective As(III) rejection. These membranes consist of a hydrophilic nickel-carbon nanotubes layer deposited on a UF support, and used as cathodes. Applying cathodic potentials significantly increased As(III) rejection in synthetic/real tap water, a result of locally elevated pH that is brought upon through water electrolysis at the membrane/water interface. The elevated pH conditions convert H3ASO3 to H2AsO3-/HAsO32- that are rejected by the negatively charged membranes. In addition, it was found that Mg(OH)2 that precipitates on the membrane can further trap arsenic. Importantly, almost all As(III) passing through the membranes is oxidized to As(V) by hydrogen peroxide produced on the cathode, which significantly decreased its overall toxicity and mobility. Although the high pH along the membrane surface led to mineral scaling, this scale could be partially removed by backwashing the membrane. To the best of our knowledge, this is the first report of effective As(III) removal using low-pressure membranes, with As(III) rejection higher than that achieved by NF and RO, and high water permeance.

Iron amendments minimize the first-flush release of pathogens from stormwater biofilters.

First flush or the first pore volume of effluent eluted from biofilters at the start of rainfall contributes to most pollution downstream because it typically contains a high concentration of bacterial pathogens. Thus, it is critical to evaluate designs that could minimize the release of bacteria during a period of high risk. In this study, we test the hypothesis of whether an addition of iron-based media to biofilter could limit the leaching of Escherichia coli (E. coli), a pathogen indicator, during the first flush. We applied E. coli-contaminated stormwater intermittently in columns packed with a mixture of sand and compost (70:30 by volume, respectively) and iron filings at three concentrations: 0% (control), 3%, and 10% by weight. Columns packed with a mixture of sand and iron (3% or 10%) without compost were used to examine the maximum capacity of iron to remove E. coli. In columns with iron, particularly 10% by weight, the leaching of E. coli during the first flush was 32% lower than the leaching from compost columns, indicating that the addition of iron amendments could decrease first-flush leaching of E. coli. We attribute this result to the ability of iron to increase adsorption and decrease growth during antecedent drying periods. Although the addition of iron filings increased E. coli removal, the presence of compost decreased the adsorption capacity: exposure of 1 g of iron filings to 1 mg of DOC reduces E. coli removal by 8%. The result was attributed to the alteration of the surface charge of iron and blocking of adsorption sites shared by E. coli and DOC. Collectively, these results indicate that the addition of sufficient amounts of iron media could decrease pathogen leaching in the first flush effluent and increase the overall biofilter performance and protect downstream water quality.

Potential-Driven Electron Transfer Lowers the Dissociation Energy of the C-F Bond and Facilitates Reductive Defluorination of Perfluorooctane Sulfonate (PFOS).

The widespread environmental occurrence of per- and polyfluoroalkyl substances (PFAS) has attracted significant regulatory, research, and media attention because of their toxicity, recalcitrance, and ability to bioaccumulate. Perfluorooctane sulfonate (PFOS) is a particularly troublesome member of the PFAS family due to its immunity to biological remediation and radical-based oxidation. In the present study, we present a heterogeneous reductive degradation process that couples direct electron transfer (ET) from surface-modified carbon nanotube electrodes (under low potential conditions) to sorbed PFOS molecules using UV-generated hydrated electrons without any further chemical addition. We demonstrate that the ET process dramatically increases the PFOS defluorination rate while yielding shorter chain (C3-C7) perfluorinated acids and present both experimental and ab initio evidence of the synergistic relationship between electron addition to sorbed molecules and their ability to react with reductive hydrated electrons. Because of the low energy consumption associated with the ET process, the use of standard medium-pressure UV lamps and no further chemical addition, this reductive degradation process is a promising method for the destruction of persistent organic pollutants, including PFAS and other recalcitrant halogenated organic compounds.

Preparation and characterization of quercetin/dietary fiber nanoformulations.

Quercetin is well known for its beneficial health effects on the human body. However, the slow dissolution rate leading to poor bioavailability constitutes a barrier to being further developed for nutritional products. In this work, quercetin was co-precipitated with dietary fibers into a fast-dissolving nanoformulation via antisolvent precipitation, followed by spray drying. With the help of cellulose fiber, resistant starch or resistant maltodextrin, a high dissolution rate and good storage stability was achieved for quercetin nanoformulations. In addition, nanoformulations exhibited higher level of antioxidant activities in contrast to raw quercetin. The developed quercetin/dietary fiber nanoformulations could be used as supplements or functional ingredients for food development.