Ultrahigh-Resolution K-Edge Imaging of Coronary Arteries With Prototype Deep-Silicon Photon-Counting CT: Initial Results in Phantoms.

Background Photon-counting CT (PCCT) represents a recent advancement in CT, offering improved spatial resolution and spectral separability. By using multiple adjustable energy bins, PCCT enables K-edge imaging, allowing mixed contrast agent distinction. Deep-silicon is a new type of photon-counting detector with different characteristics compared with cadmium photon-counting detectors. Purpose To evaluate the performance of a prototype deep-Si PCCT scanner and compare it with that of a state-of-the-art dual-energy energy-integrating detector (EID) scanner in imaging coronary artery plaques enhanced with iodine and K-edge contrast agents. Materials and Methods A series of 10 three-dimensional-printed inserts (diameter, 3.5 mm) was prepared, and materials mimicking soft and calcified plaques were added to simulate stenosed coronary arteries. Inserts filled with an iodine- or gadolinium-based contrast agent (GBCA) were scanned. Virtual monoenergetic images (VMIs) and iodine maps were generated using two- and eight-energy bin data from EID CT and PCCT, respectively. Gadolinium maps were calculated for PCCT. The CT numbers of VMIs and iodine maps were compared. Spatial resolution and blooming artifacts were compared on the 70-keV VMIs in plaque-free and calcified coronary arteries. Results No evidence of a significant difference in the CT number of 70-keV images was found except in inserts containing GBCAs. In the absence of a GBCA, excellent (r > 0.99) agreement for iodine was found. PCCT could quantify the GBCA within 0.2 mg Gd/mL ± 0.8 accuracy of the ground truth, whereas EID CT failed to detect the GBCA. Lumen measurements were more accurate for PCCT than for EID CT, with mean errors of 167 versus 442 µm (P < .001) compared with the 3.5-mm ground truth. Conclusion Deep-Si PCCT demonstrated good accuracy in iodine quantification and could accurately decompose mixtures of two contrast agents. Its improved spatial resolution resulted in sharper images with blooming artifacts reduced by 50% compared with a state-of-the-art dual-energy EID CT scanner. © RSNA, 2024.

Deep-silicon photon-counting x-ray projection denoising through reinforcement learning.

BACKGROUND: In recent years, deep reinforcement learning (RL) has been applied to various medical tasks and produced encouraging results. OBJECTIVE: In this paper, we demonstrate the feasibility of deep RL for denoising simulated deep-silicon photon-counting CT (PCCT) data in both full and interior scan modes. PCCT offers higher spatial and spectral resolution than conventional CT, requiring advanced denoising methods to suppress noise increase. METHODS: In this work, we apply a dueling double deep Q network (DDDQN) to denoise PCCT data for maximum contrast-to-noise ratio (CNR) and a multi-agent approach to handle data non-stationarity. RESULTS: Using our method, we obtained significant image quality improvement for single-channel scans and consistent improvement for all three channels of multichannel scans. For the single-channel interior scans, the PSNR (dB) and SSIM increased from 33.4078 and 0.9165 to 37.4167 and 0.9790 respectively. For the multichannel interior scans, the channel-wise PSNR (dB) increased from 31.2348, 30.7114, and 30.4667 to 31.6182, 30.9783, and 30.8427 respectively. Similarly, the SSIM improved from 0.9415, 0.9445, and 0.9336 to 0.9504, 0.9493, and 0.0326 respectively. CONCLUSIONS: Our results show that the RL approach improves image quality effectively, efficiently, and consistently across multiple spectral channels and has great potential in clinical applications.

The effects of intra-detector Compton scatter on low-frequency DQE for photon-counting CT using edge-on-irradiated silicon detectors.

BACKGROUND: Edge-on-irradiated silicon detectors are currently being investigated for use in full-body photon-counting computed tomography (CT) applications. The low atomic number of silicon leads to a significant number of incident photons being Compton scattered in the detector, depositing a part of their energy and potentially being counted multiple times. Even though the physics of Compton scatter is well established, the effects of Compton interactions in the detector on image quality for an edge-on-irradiated silicon detector have still not been thoroughly investigated. PURPOSE: To investigate and explain effects of Compton scatter on low-frequency detective quantum efficiency (DQE) for photon-counting CT using edge-on-irradiated silicon detectors. METHODS: We extend an existing Monte Carlo model of an edge-on-irradiated silicon detector with 60 mm active absorption depth, previously used to evaluate spatial-frequency-based performance, to develop projection and image domain performance metrics for pure density and pure spectral imaging tasks with 30 and 40 cm water backgrounds. We show that the lowest energy threshold of the detector can be used as an effective discriminator of primary counts and cross-talk caused by Compton scatter. We study the developed metrics as functions of the lowest threshold energy for root-mean-square electronic noise levels of 0.8, 1.6, and 3.2 keV, where the intermediate level 1.6 keV corresponds to the noise level previously measured on a single sensor element in isolation. We also compare the performance of a modeled detector with 8, 4, and 2 optimized energy bins to a detector with 1-keV-wide bins. RESULTS: In terms of low-frequency DQE for density imaging, there is a tradeoff between using a threshold low enough to capture Compton interactions and avoiding electronic noise counts. For 30 cm water phantom, 4 energy bins, and a root-mean-square electronic noise of 0.8, 1.6, and 3.2 keV, it is optimal to put the lowest energy threshold at 3, 6, and 1 keV, which gives optimal projection-domain DQEs of 0.64, 0.59, and 0.52, respectively. Low-frequency DQE for spectral imaging also benefits from measuring Compton interactions with respective optimal thresholds of 12, 12, and 13 keV. No large dependence on background thickness was observed. For the intermediate noise level (1.6 keV), increasing the lowest threshold from 5 to 35 keV increases the variance in a iodine basis image by 60%-62% (30 cm phantom) and 67%-69% (40 cm phantom), with 8 bins. Both spectral and density DQE are adversely affected by increasing the electronic noise level. Image-domain DQE exhibits similar qualitative behavior as projection-domain DQE. CONCLUSIONS: Compton interactions contribute significantly to the density imaging performance of edge-on-irradiated silicon detectors. With the studied detector topology, the benefit of counting primary Compton interactions outweighs the penalty of multiple counting at all lowest threshold energies. Compton interactions also contribute significantly to the spectral imaging performance for measured energies above 10 keV.

Hybrid U-Net and Swin-transformer network for limited-angle cardiac computed tomography.

Objective.Cardiac computed tomography (CT) is widely used for diagnosis of cardiovascular disease, the leading cause of morbidity and mortality in the world. Diagnostic performance depends strongly on the temporal resolution of the CT images. To image the beating heart, one can reduce the scanning time by acquiring limited-angle projections. However, this leads to increased image noise and limited-angle-related artifacts. The goal of this paper is to reconstruct high quality cardiac CT images from limited-angle projections.Approach. The ability to reconstruct high quality images from limited-angle projections is highly desirable and remains a major challenge. With the development of deep learning networks, such as U-Net and transformer networks, progresses have been reached on image reconstruction and processing. Here we propose a hybrid model based on the U-Net and Swin-transformer (U-Swin) networks. The U-Net has the potential to restore structural information due to missing projection data and related artifacts, then the Swin-transformer can gather a detailed global feature distribution.Main results. Using synthetic XCAT and clinical cardiac COCA datasets, we demonstrate that our proposed method outperforms the state-of-the-art deep learning-based methods.Significance. It has a great potential to freeze the beating heart with a higher temporal resolution.

Spectral optimization using fast kV switching and filtration for photon counting CT with realistic detector responses: a simulation study.

Purpose: Photon counting CT (PCCT) provides spectral measurements for material decomposition. However, the image noise (at a fixed dose) depends on the source spectrum. Our study investigates the potential benefits from spectral optimization using fast kV switching and filtration to reduce noise in material decomposition. Approach: The effect of the input spectra on noise performance in both two-basis material decomposition and three-basis material decomposition was compared using Cramer-Rao lower bound analysis in the projection domain and in a digital phantom study in the image domain. The fluences of different spectra were normalized using the CT dose index to maintain constant dose levels. Four detector response models based on Si or CdTe were included in the analysis. Results: For single kV scans, kV selection can be optimized based on the imaging task and object size. Furthermore, our results suggest that noise in material decomposition can be substantially reduced with fast kV switching. For two-material decomposition, fast kV switching reduces the standard deviation (SD) by ∼ 10 % . For three-material decomposition, greater noise reduction in material images was found with fast kV switching (26.2% for calcium and 25.8% for iodine, in terms of SD), which suggests that challenging tasks benefit more from the richer spectral information provided by fast kV switching. Conclusions: The performance of PCCT in material decomposition can be improved by optimizing source spectrum settings. Task-specific tube voltages can be selected for single kV scans. Also, our results demonstrate that utilizing fast kV switching can substantially reduce the noise in material decomposition for both two- and three-material decompositions, and a fixed Gd filter can further enhance such improvements for two-material decomposition.

Standardizing technical parameters and terms for abdominopelvic photon-counting CT: laying the groundwork for innovation and evidence sharing.

Photon-counting detector CT (PCD-CT) is a new technology that has multiple diagnostic benefits including increased spatial resolution, iodine signal, and radiation dose efficiency, as well as multi-energy imaging capability, but which also has unique challenges in abdominal imaging. The purpose of this work is to summarize key features, technical parameters, and terms, which are common amongst current abdominopelvic PCD-CT systems and to propose standardized terminology (where none exists). In addition, user-selectable protocol parameters are highlighted to facilitate both scientific evaluation and early clinical adoption. Unique features of PCD-CT systems include photon-counting detectors themselves, energy thresholds and bins, and tube potential considerations for preserved spectral separation. Key parameters for describing different PCD-CT systems are reviewed and explained. While PCD-CT can generate multi-energy images like dual-energy CT, there are new types of images such as threshold images, energy bin images, and special spectral images. The standardized terms and concepts herein build upon prior interdisciplinary consensus and have been endorsed by the newly created Society of Abdominal Radiology Photon-counting CT Emerging Technology Commission.