Power Scavenging Microsystem for Smart Contact Lenses.

On-the-eye microsystems such as smart contacts for vision correction, health monitoring, drug delivery, and displaying information represent a new emerging class of low-profile (≤ 1 mm) wireless microsystems that conform to the curvature of the eyeball surface. The implementation of suitable low-profile power sources for eye-based microsystems on curved substrates is a major technical challenge addressed in this paper. The fabrication and characterization of a hybrid energy generation unit composed of a flexible silicon solar cell and eye-blinking activated Mg-O2 metal-air harvester capable of sustainably supplying electrical power to smart ocular devices are reported. The encapsulated photovoltaic device provides a DC output with a power density of 42.4 µW cm-2 and 2.5 mW cm-2 under indoor and outdoor lighting conditions, respectively. The eye-blinking activated Mg-air harvester delivers pulsed power output with a maximum power density of 1.3 mW cm-2. A power management circuit with an integrated 11 mF supercapacitor is used to convert the harvesters' pulsed voltages to DC, boost up the voltages, and continuously deliver ≈150 µW at a stable 3.3 V DC output. Uniquely, in contrast to wireless power transfer, the power pack continuously generates electric power and does not require any type of external accessories for operation.

Refractive-type varifocal liquid-crystal Fresnel lenses for smart contacts.

We demonstrate the implementation of a low-power, low-profile, varifocal liquid-crystal Fresnel lens stack suitable for tunable imaging in smart contact lenses. The lens stack consists of a high-order refractive-type liquid crystal Fresnel chamber, a voltage-controlled twisted nematic cell, a linear polarizer and a fixed offset lens. The lens stack has an aperture of 4 mm and thickness is ∼980 µm. The varifocal lens requires ∼2.5 VRMS for a maximum optical power change of ∼6.5 D consuming electrical power of ∼2.6 µW. The maximum RMS wavefront aberration error was 0.2 µm and the chromatic aberration was 0.008 D/nm. The average BRISQUE image quality score of the Fresnel lens was 35.23 compared to 57.23 for a curved LC lens of comparable power indicating a superior Fresnel imaging quality.

Nanostructures for Biosensing, with a Brief Overview on Cancer Detection, IoT, and the Role of Machine Learning in Smart Biosensors.

Biosensors are essential tools which have been traditionally used to monitor environmental pollution and detect the presence of toxic elements and biohazardous bacteria or virus in organic matter and biomolecules for clinical diagnostics. In the last couple of decades, the scientific community has witnessed their widespread application in the fields of military, health care, industrial process control, environmental monitoring, food-quality control, and microbiology. Biosensor technology has greatly evolved from in vitro studies based on the biosensing ability of organic beings to the highly sophisticated world of nanofabrication-enabled miniaturized biosensors. The incorporation of nanotechnology in the vast field of biosensing has led to the development of novel sensors and sensing mechanisms, as well as an increase in the sensitivity and performance of the existing biosensors. Additionally, the nanoscale dimension further assists the development of sensors for rapid and simple detection in vivo as well as the ability to probe single biomolecules and obtain critical information for their detection and analysis. However, the major drawbacks of this include, but are not limited to, potential toxicities associated with the unavoidable release of nanoparticles into the environment, miniaturization-induced unreliability, lack of automation, and difficulty of integrating the nanostructured-based biosensors, as well as unreliable transduction signals from these devices. Although the field of biosensors is vast, we intend to explore various nanotechnology-enabled biosensors as part of this review article and provide a brief description of their fundamental working principles and potential applications. The article aims to provide the reader a holistic overview of different nanostructures which have been used for biosensing purposes along with some specific applications in the field of cancer detection and the Internet of things (IoT), as well as a brief overview of machine-learning-based biosensing.

Creep deformation in elastomeric membranes of liquid-filled tunable-focus lenses.

Liquid-filled tunable-focus lenses have been demonstrated to be suitable for autofocus eyewear applications. Traditionally, these lenses are constructed using an elastomeric polymer chamber filled with a high-index liquid. In this work, we investigate the effect of elastomeric creep on the deformation and eventual degradation of these tunable lenses. We use numerical analysis of a deformable circular disk representative of the lens and provide rigorous experimental results testing the creep property of a number of elastomers. Finally, we provide a comparative study of different elastomeric materials and select the best one for this application.

Parametrically Amplified Low-Power MEMS Capacitive Humidity Sensor.

We present the design, fabrication, and response of a polymer-based Laterally Amplified Chemo-Mechanical (LACM) humidity sensor based on mechanical leveraging and parametric amplification. The device consists of a sense cantilever asymmetrically patterned with a polymer and flanked by two stationary electrodes on the sides. When exposed to a humidity change, the polymer swells after absorbing the analyte and causes the central cantilever to bend laterally towards one side, causing a change in the measured capacitance. The device features an intrinsic gain due to parametric amplification resulting in an enhanced signal-to-noise ratio (SNR). Eleven-fold magnification in sensor response was observed via voltage biasing of the side electrodes without the use of conventional electronic amplifiers. The sensor showed a repeatable and recoverable capacitance change of 11% when exposed to a change in relative humidity from 25-85%. The dynamic characterization of the device also revealed a response time of ~1 s and demonstrated a competitive response with respect to a commercially available reference chip.

Tunable-focus lens for adaptive eyeglasses.

We demonstrate the implementation of a compact tunable-focus liquid lens suitable for adaptive eyeglass application. The lens has an aperture diameter of 32 mm, optical power range of 5.6 diopter, and electrical power consumption less than 20 mW. The lens inclusive of its piezoelectric actuation mechanism is 8.4 mm thick and weighs 14.4 gm. The measured lens RMS wavefront aberration error was between 0.73 µm and 0.956 µm.

Large aperture tunable-focus liquid lens using shape memory alloy spring.

A tunable-focus large aperture liquid lens is constructed using shape memory alloy (SMA) springs as actuators. The lens mainly consists of a shallow liquid-filled cylindrical cavity bound by a thin compressible annular rim and encapsulated by a flexible circular membrane on the top of the rim and a rigid circular plate at the rim bottom. The lens optical power is adjusted by a controlled compression of the annular rim via actuation of the three shape-memory alloy (SMA) springs. Since the volume of the cavity liquid is constant, the rim compression bulges the flexible membrane outward thus reducing its radius of curvature and the lens focal length. The fabricated tunable lens demonstrated an optical power range of 0-4 diopters utilizing a driving voltage less than 3V. Lens optical wavefront profiling was done using a Shack-Hartmann sensor displaying a RMS wave front error of 0.77 µm and 1.68 µm at 0 D and + 4 D. The aperture diameter and thickness of the fabricated lens are 34 mm and 9 mm, respectively, while weighing 16.7 g.

Particle-based optical pressure sensors for 3D pressure mapping.

This paper presents particle-based optical pressure sensors for in-flow pressure sensing, especially for microfluidic environments. Three generations of pressure sensitive particles have been developed- flat planar particles, particles with integrated retroreflectors and spherical microballoon particles. The first two versions suffer from pressure measurement dependence on particles orientation in 3D space and angle of interrogation. The third generation of microspherical particles with spherical symmetry solves these problems making particle-based manometry in microfluidic environment a viable and efficient methodology. Static and dynamic pressure measurements have been performed in liquid medium for long periods of time in a pressure range of atmospheric to 40 psi. Spherical particles with radius of 12 µm and balloon-wall thickness of 0.5 µm are effective for more than 5 h in this pressure range with an error of less than 5%.

Fast measurement of binding kinetics with dual slope SPR microchips.

We demonstrate a new dual slope SPR technique that is ten-fold faster than the conventional step-response method. The new scheme utilizes rapid slope-based measurements followed by rapid reset, and it separates association and dissociation half reaction measurements at two separate sites inside a dual-chamber PDMS microfluidic chip. For a model CAII-ABS test system, the association and dissociation slopes were measured in 30 seconds compared to 5 minutes for step-response. The values of k(a) and k(d) calculated from the slope method are 3.66 ± 0.19 × 10(3) M(-1) s(-1) and 4.83 ± 0.17 × 10(-2) s(-1), respectively, matching well with step-response values while facilitating ~10 to 15 fold faster detection and quantification.

Flexible and Semi-Transparent Silicon Solar Cells as a Power Supply to Smart Contact Lenses.

Supplying electric power to wearable IoT devices, particularly smart contact lenses (SCLs), is one of the main obstacles to widespread adoption and commercialization. In the present study, we have successfully designed, fabricated, and characterized semi-transparent, self-supported, and flexible single crystalline silicon solar cells using a single-sided micromachining procedure. Optical, mechanical, and electrical simulations, together with the practical measurements, verify the application of our developed solar cells to be mounted on a limited-footprint and flexible SCL. The 15 µm-thick silicon solar cells conformally fit on a dome-shaped contact lens (ROC = 8 mm) without any mechanical and electrical degradation. This homojunction photovoltaic device containing an array of micro-holes exhibits a V oc, J sc, and maximum power density of 504 mV, 6.48 mA cm-2, and 1.67 mW cm-2, respectively, at 25% visible light transparency under an AM1.5 one sun condition. Furthermore, the measurements were conducted under low-intensity indoor light conditions and resulted in a maximum power output of 25 and 42 µW cm-2 for the 50 and 25% transparent solar cells, respectively.

Correcting Presbyopia With Autofocusing Liquid-Lens Eyeglasses.

OBJECTIVE: Presbyopia, an age-related ocular disorder, is characterized by the loss in the accommodative abilities of the human eye. Conventional methods of correcting presbyopia divide the field of view, thereby resulting in significant vision impairment. We demonstrate the design, assembly and evaluation of autofocusing eyeglasses for restoration of accommodation without dividing the field of view. METHODS: The adaptive optics eyeglasses comprise of two variable-focus liquid lenses, a time-of-flight range sensor and low-power, dual microprocessor control electronics, housed within an ergonomic frame. Subject-specific accommodation deficiency models were utilized to demonstrate high-fidelity accommodative correction. The abilities of this system to reduce accommodation deficiency, its power consumption, response time, optical performance and MTF were evaluated. RESULTS: Average corrected accommodation deficiencies for 5 subjects ranged from -0.021 D to 0.016 D. Each accommodation correction calculation was performed in ∼67 ms which consumed 4.86 mJ of energy. The optical resolution of the system was 10.5 cycles/degree, and featured a restorative accommodative range of 4.3 D. This system was capable of running for up to 19 hours between charge cycles and weighed ∼132 g. CONCLUSION: The design, assembly and performance of an autofocusing eyeglasses system to restore accommodation in presbyopes has been demonstrated. SIGNIFICANCE: The new autofocusing eyeglasses system presented in this article has the potential to restore pre-presbyopic levels of accommodation in subjects diagnosed with presbyopia.

Low-Profile Induced-Voltage Distance Ranger for Smart Contact Lenses.

OBJECTIVE: In this paper, we present a novel, low-profile, scleral-coil based, distance ranging system which is suitable for smart, accommodating contact lenses. METHODS: We measure the induced emf between a set of four thin semi-circular coils patterned on flexible Kapton substrates that conform to the eyes' sclera. This induced emf is a function of eye gaze angles. The system then determines the distance from the eyes to the desired object via the triangulation of these eye gaze angles Results: Experiments on eyeball simulated tissue gels indicate an accurate prediction of object distance in the 0.1-15 D range with a 0.15 D RMS error and object direction in the -15 to 15-degree arc with 0.4-degree RMS error, respectively. The energy required was determined to be as low as 20 µJ per range reading. CONCLUSION: Experimental data shows that our proposed new method of eye-tracking and distance ranging system can accurately predict eye-gaze angles and object-distance, whilst using only 20 µJ per range reading. SIGNIFICANCE: The high-accuracy, low-profile and reduced energy requirements of the proposed eye-tracking technique, make it suitable for applications in the vast field of adaptive optics such as smart contact lenses and other low-power vision corrective applications.

Low noise detection of biomolecular interactions with signal-locking surface plasmon resonance.

Surface plasmon resonance (SPR) is a popular technique for label-free detection of biomolecular interactions at a surface. SPR yields quantitative kinetic association and dissociation constants of surface interactions such as the binding of two molecular species, one present in the liquid phase and the other immobilized at the surface. Current state-of-the-art SPR systems extract kinetic constants from measurements of the step response of the interaction versus time. The step response measurement is subject to the influence of noise and drift disturbances that limit its minimum-detectable mass changes. This paper presents a new SPR technique that measures the biomolecular interaction not in time but over a very narrow frequency range under periodic excitation. The measured response is, thus, locked to a very specific narrow band signal. This narrow band spectral sensing scheme has a very high degree of rejection to uncorrelated spurious signals. The signal-locked SPR technique was implemented using a chemical modulator chip connected to a set of functionalized Au sensing sites downstream. Binding experiments for a model system of carbonic anhydrase-II (CA-II) analyte and immobilized 4-(2-aminoethyl)benzenesulfonamide (ABS) ligand display a 100-fold (20 dB) improvement in the measured signal-to-noise ratio (SNR) when using the new technique compared to the SNR achieved using the conventional step response method.

Batch-Fabricated α-Si Assisted Nanogap Tunneling Junctions.

This paper details the design, fabrication, and characterization of highly uniform batch-fabricated sidewall etched vertical nanogap tunneling junctions for bio-sensing applications. The device consists of two vertically stacked gold electrodes separated by a partially etched sacrificial spacer layer of sputtered α-Si and Atomic Layer Deposited (ALD) SiO2. A ~10 nm wide air-gap is formed along the sidewall by a controlled dry etch of the spacer. The thickness of the spacer layer can be tuned by adjusting the number of ALD cycles. The rigorous statistical characterization of the ultra-thin spacer films has also been performed. We fabricated nanogap electrodes under two design layouts with different overlap areas and spacer gaps, from ~4.0 nm to ~9.0 nm. Optical measurements reported an average non-uniformity of 0.46 nm (~8%) and 0.56 nm (~30%) in SiO2 and α-Si film thickness respectively. Direct tunneling and Fowler-Nordheim tunneling measurements were done and the barrier potential of the spacer stack was determined to be ~3.5 eV. I-V measurements showed a maximum resistance of 46 × 103 GΩ and the average dielectric breakdown field of the spacer stack was experimentally determined to be ~11 MV/cm.

A Low-Profile Digital Eye-Tracking Oculometer for Smart Eyeglasses.

Wearable eye tracking devices have broad uses in medicine, psychology, augmented & virtual reality and consumer market research. Most mobile eye trackers available today utilize infrared imaging of the pupil and corneal reflections with video cameras. This tracking method requires sophisticated real-time processing of video signals consuming substantial electrical power. This method is thus unsuitable for light weight wearables such as adaptive smart eyeglasses for correction of presbyopia. In this paper we present a low-profile, low-power (7.7 mJ/sample) digital eye tracker oculometer based on infrared sclera tracking. The system is implemented using eight, 24-bit infrared proximity sensors and synchronous infrared LEDs. The pupil location is determined from 32 reflected pulsed light measurements independent of ambient illumination. The digital oculometer is 3.1 mm thick and weighs ~3 g. The tracker mounts adjacent to the tunable lenses in the smart eyeglasses frame. The eye tracker showed a pointing error of 1.3 degrees rms over a vertical and horizontal range of 30 degrees when tested by an observer.

Low-Cost High-Speed In-Plane Stroboscopic Micro-Motion Analyzer.

Instrumentation for high-speed imaging and laser vibrometry is essential for the understanding and analysis of microstructure dynamics, but commercial instruments are largely unaffordable for most microelectromechanical systems (MEMS) laboratories. We present the implementation of a very low cost in-plane micro motion stroboscopic analyzer that can be directly attached to a conventional probe station. The low-cost analyzer has been used to characterize the harmonic motion of 52.1 kHz resonating comb drive microactuators using ~50 ns pulsed light-emitting diode (LED) stroboscope exposure times, producing sharp and high resolution (~0.5 µm) device images at resonance, which rivals those of several orders of magnitude more expensive systems. This paper details the development of the high-speed stroboscopic imaging system and presents experimental results of motion analysis of example microstructures and a discussion of its operating limits. The system is shown to produce stable stroboscopic LED illumination to freeze device images up to 11 MHz.

Direct imaging of DNA motif sequences with encoded nanoparticles.

We present a method for encoded tagging and imaging of short nucleic acid motif chains (oligomotifs) using selective hybridization of heterogeneous Au nanoparticles (Au-NP). The resulting encoded NP string is thus representative of the underlying motif sequence. As the NPs are much more massive than the motifs, the motif chain order can be directly observed using scanning electron microscopy. Using this technique we demonstrate direct sequencing of oligomotifs in single DNA molecules consisting of four 100-nt motif chains tagged with four different types of NPs. The method outlined is a precursor for a high density direct sequencing technology.

Direct imaging of DNA motif sequences with encoded nanoparticles.

We present a method for encoded tagging and imaging of short nucleic acid motif chains (oligomotifs) using selective hybridization of heterogeneous Au nanoparticles. The resulting encoded nanoparticle string is thus representative of the underlying motif sequence. Since the nanoparticles are much more massive than the motifs; the motif chain order can be directly observed using scanning electron microscopy. Using this technique we demonstrate direct sequencing of oligomotifs in single DNA molecules consisting of four 100-bp motif chains tagged with four different types of nanoparticles. The method outlined is a precursor for a high density direct sequencing technology.

Label-free detection of protein binding with multisine SPR microchips.

Label-free techniques such as surface plasmon resonance (SPR) have used a step-response excitation method to characterize the binding of two biochemical entities. A major drawback of the step response technique is its high susceptibility to thermal drifts and noise which directly determine the minimum detectable binding mass. In this paper we present a new frequency-domain method based on the use of multisine chemical excitation that is much less sensitive to these disturbances. The multisine method was implemented in a PDMS microfluidic chip using a dual channel, dual multiplug chemical signal generator connected to functionalized and reference SPR binding spots. Kinetic constants for the reaction are extracted from the characteristics of the sense spot response versus frequency. The feasibility of the technique was tested using a model system of Carbonic Anhydrase-II analyte and amino-benzenesulfonamide ligand. The experimental signal to noise ratio (SNR) for the multisine measurement is about 32 dB; 7 dB higher than that observed with the single step-response method, while the overall measurement time is twice as long as the step method.

Chemical neurostimulation using pulse code modulation (PCM) microfluidic chips.

We report the implementation of a chemical neurostimulation technique using microfluidic devices. The microfluidic chip in this research is used for the in vitro study of the nervous system of Aplysia californica under localized chemical stimulation. The polydimethylsiloxane (PDMS) device is a one-bit pulse code modulator that digitally controls the concentration of the non-hydrolysable cholinergic agonist carbachol injected directly above a ganglion. The chip was successful in repeatedly and controllably inducing bursts of ingestive-like patterns. The ability of the chip to induce rhythmic activity through the sheath of the ganglion suggests that it could serve as the basis for an implantable, in vivo device to control neural activity and motor behavior using chemical stimulation.