ABSTRACT
In this study, we developed a high-performance non-enzymatic electrochemical sensor based on urchin-like CoP3/Cu3P heterostructured nanorods supported on a three-dimensional porous copper foam, namely, CoP3/Cu3P NRs/CF, for the detection of dopamine. Benefiting from the promising intrinsic catalytic activities of CoP3 and Cu3P, urchin-like microsphere structures, and a large electrochemically active surface area for exposing numerous accessible catalytic active sites, the proposed CoP3/Cu3P NRs/CF shows extraordinary electrochemical response towards the electrocatalytic oxidation of dopamine. As a result, the CoP3/Cu3P NRs/CF sensing electrode has a broad detection window (from 0.2 to 2000 µM), low detection limit (0.51 µM), high electrochemical sensitivity (0.0105 mA µM-1 cm-2), excellent selectivity towards dopamine in the coexistence of some interfering species, and good stability for dopamine determination. More importantly, the CoP3/Cu3P NRs/CF catalyst also exhibits excellent catalytic activity, sensitivity, and selectivity for dopamine detection under simulated human body conditions at a physiological pH of 7.25 (0.1 M PBS) at 36.6 °C.
Subject(s)
Copper , Dopamine , Electrochemical Techniques , Nanotubes , Dopamine/analysis , Dopamine/chemistry , Copper/chemistry , Electrochemical Techniques/methods , Nanotubes/chemistry , Porosity , Catalysis , Cobalt/chemistry , Electrodes , Limit of Detection , Oxidation-ReductionABSTRACT
Electrochemical conversion of CO2 to fuels and chemicals as a sustainable solution for waste transformation has garnered tremendous interest to combat the fervent issue of the prevailing high atmospheric CO2 concentration while contributing to the generation of sustainable energy. Monometallic palladium (Pd) has been shown promising in electrochemical CO2 reduction, producing formate or CO depending on applied potentials. Recently, bimetallic Pd-based materials strived to fine-tune the binding affinity of key intermediates is a prominent strategy for the desired product formation from CO2 reduction. Herein, the recent emerging trends on bimetallic Pd-based electrocatalysts are reviewed, including fundamentals of CO2 electroreduction and material engineering of bimetallic Pd-electrocatalysts categorized by primary products. Modern analytical techniques on these novel electrocatalysts are also thoroughly studied to get insights into reaction mechanisms. Lastly, we deliberate over the challenges and prospects for Pd-based catalysts for electrochemical CO2 conversion.
ABSTRACT
Pd is one of the most effective catalysts for the electrochemical reduction of CO2 to formate, a valuable liquid product, at low overpotential. However, the intrinsically high CO affinity of Pd makes the surface vulnerable to CO poisoning, resulting in rapid catalyst deactivation during CO2 electroreduction. Herein, we utilize the interaction between metals and metal-organic frameworks to synthesize atomically dispersed Au on tensile-strained Pd nanoparticles showing significantly improved formate production activity, selectivity, and stability with high CO tolerance. We found that the tensile strain stabilizes all reaction intermediates on the Pd surface, whereas the atomically dispersed Au selectively destabilizes CO* without affecting other adsorbates. As a result, the conventional COOH* versus CO* scaling relation is broken, and our catalyst exhibits 26- and 31-fold enhancement in partial current density and mass activity toward electrocatalytic formate production with over 99% faradaic efficiency, compared to Pd/C at -0.25 V versus RHE.
ABSTRACT
Solar-driven carbon dioxide (CO2) conversion has gained tremendous attention as a prominent strategy to simultaneously reduce the atmospheric CO2 concentration and convert solar energy into solar fuels in the form of chemical bonds. Numerous efforts have been devoted to diverse photo-driven processes for CO2 conversion, which utilized a multidisciplinary strategy. Among them, the architecture of nanostructured metal-based catalysts is emerging as an eminent solution for the design of catalysts of this field. In this work, we first provide fundamental mechanisms of photochemical, photoelectrochemical, photothermal, and photobio(electro)chemical CO2 reduction processes to achieve an in-deep understanding of vital aspects. Importantly, the recent progress in the catalyst design for each reaction system is discussed and highlighted. Based on these analyses, an overview of photo-driven CO2 reduction on metal-based catalysts for solar fuel production is also spotlighted. Finally, we analyze challenges and prospects for the strategic direction of developments in the field.
Subject(s)
Carbon Dioxide , Solar Energy , Catalysis , Metals , SunlightABSTRACT
Anionic Congo red dye (CR) is not effectively removed by conventional adsorbents. Three novel biochars derived from agro-waste (Acacia auriculiformis), modified with metal salts of FeCl3, AlCl3, and CaCl2 at 500 °C pyrolysis have been developed to enhance CR treatment. These biochars revealed significant differences in effluents compared to BC, which satisfied initial research expectations (P < 0.05). The salt concentration of 2 M realized optimal biochars with the highest CR removal of 96.8%, for AlCl3-biochar and FeCl3-biochar and 70.8% for CaCl2-biochar. The modified biochars were low in the specific surface area (137.25-380.78 m2 g-1) compared normal biochar (393.15 m2 g-1), had more heterogeneous particles and successfully integrated metal oxides on the surface. The CR removal increased with a decrease in pH and increase in biochar dosage, which established an optimal point at an initial loading of 25 mg g-1. Maximum adsorption capacity achieved 130.0, 44.86, and 30.80 mg g-1 for BFe, BCa, and BAl, respectively. As magnetic biochar, which is easily separated from the solution and achieves a high adsorption capacity, FeCl3-biochar is the preferred biochar for CR treatment application.
Subject(s)
Congo Red , Water Pollutants, Chemical , Adsorption , Charcoal , MetalsABSTRACT
Titanium dioxide (TiO2) has attracted increasing attention as a candidate for the photocatalytic reduction of carbon dioxide (CO2) to convert anthropogenic CO2 gas into fuels combined with storage of intermittent and renewable solar energy in forms of chemical bonds for closing the carbon cycle. However, pristine TiO2 possesses a large band gap (3.2 eV), fast recombination of electrons and holes, and low selectivity for the photoreduction of CO2. Recently, considerable progress has been made in the improvement of the performance of TiO2 photocatalysts for CO2 reduction. In this review, we first discuss the fundamentals of and challenges in CO2 photoreduction on TiO2-based catalysts. Next, the recently emerging progress and advances in TiO2 nanostructured and hybrid materials for overcoming the mentioned obstacles to achieve high light-harvesting capability, improved adsorption and activation of CO2, excellent photocatalytic activity, the ability to impede the recombination of electrons-holes pairs, and efficient suppression of hydrogen evolution are discussed. In addition, approaches and strategies for improvements in TiO2-based photocatalysts and their working mechanisms are thoroughly summarized and analyzed. Lastly, the current challenges and prospects of CO2 photocatalytic reactions on TiO2-based catalysts are also presented.
ABSTRACT
Low dimensional transition metal carbide and nitride (MXenes) have been emerging as frontier materials for energy storage and conversion. Ti3C2Tx was the first MXenes that discovered and soon become the most widely investigated among the MXenes family. Interestingly, Ti3C2Tx exhibits ultrahigh catalytic activity towards the hydrogen evolution reaction. In addition, Ti3C2Tx is electronically conductive, and its optical bandgap is tunable in the visible region, making it become one of the most promising candidates for the photocatalytic hydrogen evolution reaction (HER). In this review, we provide comprehensive strategies for the utilization of Ti3C2Tx as a catalyst for improving solar-driven HER, including surface functional groups engineering, structural modification, and cocatalyst coupling. In addition, the reaming obstacle for using these materials in a practical system is evaluated. Finally, the direction for the future development of these materials featuring high photocatalytic activity toward HER is discussed.
ABSTRACT
Carbon-based materials are promising candidates as charge transport layers in various optoelectronic devices and have been applied to enhance the performance and stability of such devices. In this paper, we provide an overview of the most contemporary strategies that use carbon-based materials including graphene, graphene oxide, carbon nanotubes, carbon quantum dots, and graphitic carbon nitride as buffer layers in polymer solar cells (PSCs). The crucial parameters that regulate the performance of carbon-based buffer layers are highlighted and discussed in detail. Furthermore, the performances of recently developed carbon-based materials as hole and electron transport layers in PSCs compared with those of commercially available hole/electron transport layers are evaluated. Finally, we elaborate on the remaining challenges and future directions for the development of carbon-based buffer layers to achieve high-efficiency and high-stability PSCs.