Siloxene-Functionalized Laser-Induced Graphene via COSi Bonding for High-Performance Heavy Metal Sensing Patch Applications.

Here, 2D Siloxene nanosheets are newly applied to functionalize porous laser-induced graphene (LIG) on polydimethylsiloxane, modify the surface chemical properties of LIG, and improve the heterogeneous electron transfer rate. Meanwhile, the newly generated COSi crosslink boosts the binding of LIG and Siloxene. Thus, the Siloxene/LIG composite is used as the basic electrode material for the multifunctional detection of copper (Cu) ions, pH, and temperature in human perspiration. Moreover, to enhance the sensing performance of Cu ions, Siloxene/LIG is further modified by carbon nanotubes (CNTs). The fabricated Siloxene-CNT/LIG-based Cu-ion sensor shows linear response within a wide range of 10-500 ppb and a low detection limit of 1.55 ppb. In addition, a pH sensor is integrated to calibrate for determining the accurate concentration of Cu ions due to pH dependency of the Cu-ion sensor. The polyaniline-deposited pH sensor demonstrates a good sensitivity of -64.81 mV pH-1 over the pH range of 3-10. Furthermore, a temperature sensor for accurate skin temperature monitoring is also integrated and exhibits a stable linear resistance response with an excellent sensitivity of 9.147 Ω °C-1 (correlation coefficient of 0.139% °C-1 ). The flexible hybrid sensor is promising in applications of noninvasive heavy-metal ion detection and prediction of related diseases.

A rime ice-inspired bismuth-based flexible sensor for zinc ion detection in human perspiration.

A nature-inspired special structure of bismuth is newly presented as Zn ion sensing layer for high-performance electrochemical heavy metal detection sensor applications. The rime ice-like bismuth (RIBi) has been synthesized using an easy ex situ electrodeposition method on the surface of a flexible graphene-based electrode. The flexible graphene-based electrode was fabricated via simple laser-writing and substrate-transfer techniques. The Zn ion sensing performance of the proposed heavy metal sensor was evaluated by square wave anodic stripping voltammetry after investigating the effects of several parameters, such as preconcentration potential, preconcentration time, and pH of acetate buffer. The proposed RIBi-based heavy metal sensor demonstrated a good linear relationship between concentration and current in the range 100-1600 ppb Zn ions with an acceptable sensitivity of 106 nA/ppb·cm2. The result met the requirements in terms of common human perspiration levels (the average Zn ion concentration in perspiration is 800 ppb). In addition, the heavy metal sensor response to Zn ions was successfully performed in human perspiration samples as well, and the results were consistent with those measured by atomic absorption spectroscopy. Besides, the fabricated Zn ion sensor exhibited excellent selectivity, repeatability, and flexibility. Finally, a PANI-LIG-based pH sensor (measurement range: pH 4-7) was also integrated with the Zn ion sensor to form a single chip hybrid sensor. These results may provide a great possibility for the use of the proposed flexible sensor to realize wearable perspiration-based healthcare systems. Graphical abstract.

An Electrodeposited MXene-Ti3C2Tx Nanosheets Functionalized by Task-Specific Ionic Liquid for Simultaneous and Multiplexed Detection of Bladder Cancer Biomarkers.

Controlled deposition of 2D multilayered nanomaterials onto different electrodes to design a highly sensitive biosensing platform utilizing their active inherent electrochemistry is extremely challenging. Herein, a green, facile, and cost-effective one-pot deposition mechanism of 2D MXene-Ti3C2Tx nanosheets (MXNSs) onto conductive electrodes within few minutes via electroplating (termed electroMXenition) is reported for the first time. The redox reaction in the colloidal MXNS solution under the effect of a constant applied potential generates an electric field, which drives the nanoparticles toward a specific electrode interface such that they are cathodically electroplated. A task-specific ionic liquid, that is, 4-amino-1-(4-formyl-benzyl) pyridinium bromide (AFBPB), is exploited as a multiplex host arena for the substantial immobilization of MXNSs and covalent binding of antibodies. A miniaturized, single-masked gold dual interdigitated microelectrode (DIDµE) is microfabricated and presented by investigating the benefit of AFBPB coated on MXNSs. The resulting MXNSs-AFBPB-film-modified DIDµE biosensor exhibited a 7× higher redox current than bare electrodes owing to the uniform deposition. Using Apo-A1 and NMP 22 as model bladder cancer analytes, this newly developed dual immunosensor demonstrated precise and large linear ranges over five orders of significance with limit of detection values as low as 0.3 and 0.7 pg mL-1, respectively.

Engineering of a tumor cell-specific, cytosol-penetrating antibody with high endosomal escape efficacy.

The main obstacles for practical uses of cytosol-penetrating peptides and proteins include their lack of cell- or tissue-specific targeting and limited cytosolic access owing to the poor endosomal escape ability. We have previously reported a cytosol-penetrating, human IgG1 antibody TMab4-WYW, generally referred to as a cytotransmab (CT), which reaches the cytosol of living cells but nonspecifically because it is endocytosed via a ubiquitously expressed receptor called heparan sulfate proteoglycan (HSPG). Here, our aim was to construct a next-generation CT with tumor cell specificity and improved endosomal escape efficiency. We first substantially reduced the HSPG-binding activity of TMab4-WYW and then fused a cyclic peptide specifically recognizing tumor-associated epithelial cell adhesion molecule (EpCAM) to the N terminus of the light chain for EpCAM-mediated endocytosis, while maintaining the endosomal escape ability in the light chain variable domain (VL), thus generating epCT05. Then, we separately engineered another CT, dubbed epCT65-AAA, with an endosomal escape ability only in the heavy chain variable domain (VH) but not in VL, by functional grafting of the endosomal escape motif of epCT05 VL to the VH. We finally combined the heavy chain of epCT65-AAA and the light chain of epCT05 to create epCT65 with endosomal escape capacity in both the VH and VL. epCT65 effectively localized to the cytosol of only EpCAM-expressing tumor cells and showed approximately twofold improved endosomal escape efficiency, as compared with CTs with endosomal escape motifs in either VH or VL. The full-IgG format CT, epCT65, with a tumor cell-specific cytosol-penetrating activity, has a great potential for practical medical applications, e.g., as a carrier for cytosolic delivery of payloads.

Development of Multi-Degree-Of-Freedom Piezoelectric Energy Harvester Using Interdigital Shaped Cantilevers.

A piezoelectric vibration energy harvester with interdigital shaped cantilever was developed by using silicon bulk micromachining technology. The proposed energy harvester was designed to obtain multi degree-of-freedom (m-DOF). Most of the piezoelectric vibration energy harvesters are comprised of mass-loaded cantilever beams having several resonant frequencies. The second resonant frequency of such a device has lower amplitude compared to its first resonant frequency (fundamental frequency). Therefore, the interdigital shaped cantilever has been proposed for multiple fundamental resonant frequencies. The fabricated piezoelectric vibration energy harvester is composed of main cantilever (MC), sub-main cantilever (SMC), and secondary cantilevers (SC). MC surrounds SMC and SC which have same dimension of 5600 x 800 x 10 µm3. The fabricated piezoelectric energy harvester can generate 51.4 mV(p-p) and 11 mV(p-p) of output voltages at 24.2 Hz and 33 Hz of its resonant frequencies by MC. Moreover, it can generate 8 mV(p-p) and 6.6 mV(p-p) of output voltages at 24.2 Hz and 33.2 Hz of its resonant frequencies by SMC; and 364 mV(p-p) of output voltage at 33.6 Hz of its resonant frequency by SC.

Alternative to canal wall-down mastoidectomy for sclerotic mastoid cavities: epitympanoplasty with mastoid obliteration.

OBJECTIVES: Surgical procedures for chronic ear disease can be grossly divided into two tympanoplasty procedures: canal wall-up and canal wall-down (CWD) mastoidectomies. The choice depends on the surgeon's preference. Epitympanoplasty with mastoid obliteration (EMO) has shown postoperative results similar to those of CWD mastoidectomy with long-term follow-up. In this study, we compared the outcomes of EMO and CWD mastoidectomy in preoperatively sclerotic mastoid cavities with cholesteatoma, chronic otitis media with poor eustachian tube function, or adhesive otitis media. The operations were performed by the same surgeons in order to eliminate any effect of surgeon preference on the surgical outcomes. METHODS: We reviewed the medical records of patients who underwent tympanoplasty with EMO (EMO group) or CWD mastoidectomy (CWD group) and followed them for more than 28 months. The postoperative outcomes were analyzed and compared. RESULTS: The EMO and CWD groups comprised 132 and 110 ears, respectively. In both groups, the air-bone gaps were significantly reduced after operation. The relapse rates of the groups were similar. Cavity problems were the most common complication in the CWD group. The overall complication rate in the EMO group was significantly lower than that in the CWD group (p = 0.044). CONCLUSIONS: Epitympanoplasty with mastoid obliteration can be considered an alternative procedure to CWD mastoidectomy in patients with preoperatively sclerotic mastoid cavities. It gives similar surgical results and has fewer complications.

Polyaromatic Hydrocarbon-Functionalized 2D MXene-Based 3D Porous Antifouling Nanocomposite with Long Shelf Life for High-Performance Electrochemical Immunosensor Applications.

Affinity-based electrochemical (AEC) biosensors have gained more attention in the field of point-of-care management. However, AEC sensing is hampered by biofouling of the electrode surface and degradation of the antifouling material. Therefore, a breakthrough in antifouling nanomaterials is crucial for the fabrication of reliable AEC biosensors. Herein, for the first time, we propose 1-pyrenebutyric acid-functionalized MXene to develop an antifouling nanocomposite to resist biofouling in the immunosensors. The nanocomposite consisted of a 3D porous network of bovine serum albumin cross-linked with glutaraldehyde with functionalized MXene as conductive nanofillers, where the inherited oxidation resistance property of functionalized MXene improved the electrochemical lifetime of the nanocomposite. On the other hand, the size-extruded porous structure of the nanocomposite inhibited the biofouling activity on the electrode surface for up to 90 days in real samples. As a proof of concept, the antifouling nanocomposite was utilized to fabricate a multiplexed immunosensor for the detection of C-reactive protein (CRP) and ferritin biomarkers. The fabricated sensor showed good selectivity over time and an excellent limit of detection for CRP and ferritin of 6.2 and 4.2 pg/mL, respectively. This research successfully demonstrated that functionalized MXene-based antifouling nanocomposites have great potential to develop high-performance and low-cost immunosensors.

Multifunctional Siloxene-Decorated Laser-Inscribed Graphene Patch for Sweat Ion Analysis and Electrocardiogram Monitoring.

Potentiometric detection in complex biological fluids enables continuous electrolyte monitoring for personal healthcare; however, the commercialization of ion-selective electrode-based devices has been limited by the rapid loss of potential stability caused by electrode surface inactivation and biofouling. Here, we describe a simple multifunctional hybrid patch incorporating an Au nanoparticle/siloxene-based solid contact (SC) supported by a substrate made of laser-inscribed graphene on poly(dimethylsiloxane) for the noninvasive detection of sweat Na+ and K+. These SC nanocomposites prevent the formation of a water layer during ion-to-electron transfer, preserving 3 and 5 µV/h potential drift for the Na+ and K+ ion-selective electrodes, respectively, after 13 h of exposure. The lamellar structure of the siloxene sheets increases the SC area. In addition, the electroplated Au nanoparticles, which have a large surface area and excellent conductivity, further increased the electric double-layer capacitance at the interface between the ion-selective membranes and solid-state contacts, thus facilitating ion-to-electron transduction and ultimately improving the detection stability of Na+ and K+. Furthermore, the integrated temperature and electrocardiogram sensors in the flexible patch assist in monitoring body temperature and electrocardiogram signals, respectively. Featuring both electrochemical ion-selective and physical sensors, this patch offers immense potential for the self-monitoring of health.

Reduced graphene oxide-functionalized polymer microneedle for continuous and wide-range monitoring of lactate in interstitial fluid.

Despite substantial developments in minimally invasive lactate monitoring microneedle electrodes, most such electrode developments have focused on either sensitivity or invasiveness while ignoring a wide range of detection, which is the most important factor in measuring the normal range of lactate in interstitial fluid (ISF). Herein, we present a polymer-based planar microneedle electrode fabrication using microelectromechanical and femtosecond laser technology for the continuous monitoring of lactate in ISF. The microneedle is functionalized with two-dimensional reduced graphene oxide (rGO) and electrochemically synthesized platinum nanoparticles (PtNPs). A particular quantity of Nafion (1.25 wt%) is applied on top of the lactate enzyme to create a diffusion-controlled membrane. Due to the combined effects of the planar structure of the microneedle, rGO, and membrane, the biosensor exhibited excellent linearity up to 10 mM lactate with a limit of detection of 2.04 µM, high sensitivity of 43.96 µA mM-1cm-2, a reaction time of 8 s and outstanding stability, selectivity, and repeatability. The feasibility of the microneedle is evaluated by using it to measure lactate concentrations in artificial ISF and human serum. The results demonstrate that the microneedle described here has great potential for use in real-time lactate monitoring for use in sports medicine and treatment.

Characterization of electroplated multilayered nanoporous platinum films for electrochemical sensor applications.

We newly fabricated and characterized the double layered nanoporous Pt (NPt) thin film on silicon substrate for enzyme-free glucose sensing applications. The surface morphologies of the fabricated NPt film were characterized using field emission scanning electron microscopy (FESEM). The fabricated NPt films exhibited highly dense nanopores with irregularly arranged grain boundaries and thicknesses of 0.77 microm, which were highly affected by the structural geometries of the bottom layer. The electrochemical properties of the double layered NPt films were tested in 1 M sulfuric acid and phosphate buffered saline (PBS, pH 7.4) with different concentrations of glucose. The NPt film on silicon substrate exhibited extremely high electrochemical roughness factor (RF) of 901.35 (mean values) and sensitivities of 33.34 microA mM(-1) cm(-2) in glucose concentrations up to 16 mM.

A bulk micromachined lead zinconate titanate cantilever energy harvester with inter-digital IrO(x) electrodes.

A piezoelectric vibration energy harvester with inter-digital IrO(x) electrode was developed by using silicon bulk micromachining technology. Most PZT cantilever based energy harvesters have utilized platinum electrode material. However, the PZT fatigue characteristics and adhesion/delamination problems caused by the platinum electrode might be serious problem in reliability of energy harvester. To address these problems, the iridium oxide was newly applied. The proposed energy harvester was comprised of bulk micromachined silicon cantilever with 800 x 1000 x 20 microm3, which having a silicon supporting membrane, sol-gel-spin coated Pb(Zr52, Ti48)O3 thin film, and sputtered inter-digitally shaped IrO(x) electrodes, and silicon inertial mass with 1000 x 1000 x 500 microm3 to adjust its resonant frequency. The fabricated energy harvester generated 1 microW of electrical power to 470 komega of load resistance and 1.4 V(peak-to-peak) from a vibration of 0.4 g at 1.475 kHz. The corresponding power density was 6.25 mW x cm(-3) x g(-2). As expected, its electrical failure was significantly improved.

Highly Sensitive and Reliable Piezoresistive Strain Sensor Based on Cobalt Nanoporous Carbon-Incorporated Laser-Induced Graphene for Smart Healthcare Wearables.

The development of highly sensitive, reliable, and cost-effective strain sensors is a big challenge for wearable smart electronics and healthcare applications, such as soft robotics, point-of-care systems, and electronic skins. In this study, we newly fabricated a highly sensitive and reliable piezoresistive strain sensor based on polyhedral cobalt nanoporous carbon (Co-NPC)-incorporated laser-induced graphene (LIG) for wearable smart healthcare applications. The synergistic integration of Co-NPC and LIG enables the performance improvement of the strain sensor by providing an additional conductive pathway and robust mechanical properties with a high surface area of Co-NPC nanoparticles. The proposed porous graphene nanosheets exploited with Co-NPC nanoparticles demonstrated an outstanding sensitivity of 1,177 up to a strain of 18%, which increased to 39,548 beyond 18%. Additionally, the fabricated sensor exhibited an ultralow limit of detection (0.02%) and excellent stability over 20,000 cycles even under high strain conditions (10%). Finally, we successfully demonstrated and evaluated the sensor performance for practical use in healthcare wearables by monitoring wrist pulse, neck pulse, and joint flexion movement. Owing to the outstanding performance of the sensor, the fabricated sensor has great potential in electronic skins, human-machine interactions, and soft robotics applications.

Stretchable and All-Directional Strain-Insensitive Electronic Glove for Robotic Skins and Human-Machine Interfacing.

Electronic gloves (e-gloves), with their multifunctional sensing capability, hold a promising application in robotic skin and human-machine interfaces, endowing robots with a human sense of touch. Despite the progress in developing e-gloves by exploiting flexible or stretchable sensors, existing models have inherent rigidity in their sensing area, limiting their stretchability and sensing performance. Herein, we present an all-directional strain-insensitive stretchable e-glove that successfully extends sensing functionality such as pressure, temperature, humidity, and ECG with minimal crosstalk. A scalable and facile method is successfully demonstrated by combining low-cost CO2 laser engraving and electrospinning technology to fabricate multimodal e-glove sensors with a vertical architecture. In comparison to other smart gloves, the proposed e-glove features a ripple-like meandering sensing area and interconnections that are designed to stretch in response to the applied deformation, without affecting the performance of the sensors offering full mechanical stretchability. Furthermore, CNT-coated laser-engraved graphene (CNT/LEG) is used as an active sensing material in which the cross-linking network of the CNT in the LEG minimizes the stress effect and maximizes the sensitivity of the sensors. The fabricated e-glove can detect hot/cold, moisture, and pain simultaneously and precisely, while also allowing for remote transmission of sensory data to the user.

A hybridized nano-porous carbon reinforced 3D graphene-based epidermal patch for precise sweat glucose and lactate analysis.

Wearable electrochemical biosensors for perspiration analysis offer a promising non-invasive biomarker monitoring method. Herein, a functionalized hybridized nanoporous carbon (H-NPC)-encapsulated flexible 3D porous graphene-based epidermal patch was firstly fabricated for monitoring sweat glucose, lactate, pH, and temperature using simple, cost-effective, laser-engraved, and spray-coating techniques. The fabricated H-NPC-modified electrode significantly increased electrochemical surface area and electrocatalytic activity. Within the physiological sweat range (0-1.5 mM), the second-generation glucose sensor exhibited an excellent sensitivity of 82.7 µAmM-1cm-2 with 0.025 µM LOD. Moreover, the lactate biosensor exhibited an extraordinary linear range (0-56 mM) response owing to the incorporation of an outer diffusion limiting layer (DLL) that controls the lactate flux reaching the enzyme with comparable sensitivity (204 nAmM-1cm-2) and LOD (4 µM). Finally, we employed an analytical correction approach incorporating pH and temperature adjustments during on-body tests. In addition to connecting various carbon-based materials to limitless metal-organic frameworks as a transduction material, our research also paves the way for enabling these sensors to operate on pH and T correction independently while delivering accurate results.

Microfluidic-Integrated Multimodal Wearable Hybrid Patch for Wireless and Continuous Physiological Monitoring.

Despite extensive advances in wearable monitoring systems, most designs focus on the detection of physical parameters or metabolites and do not consider the integration of microfluidic channels, miniaturization, and multimodality. In this study, a combination of multimodal (biochemical and electrophysiological) biosensing and microfluidic channel-integrated patch-based wireless systems is designed and fabricated using flexible materials for improved wearability, ease of operation, and real-time and continuous monitoring. The reduced graphene oxide-based microfluidic channel-integrated glucose biosensor exhibits a good sensitivity of 19.97 (44.56 without fluidic channels) µA mM-1 cm-2 within physiological levels (10 µM-0.4 mM) with good long-term and bending stability. All the sensors in the patch are initially validated using sauna gown sweat-based on-body and real-time tests with five separate individuals who perspired three times each. Multimodal glucose and electrocardiogram (ECG) sensing, along with their real-time adjustment based on sweat pH and temperature fluctuations, optimize sensing accuracy. Laser-burned hierarchical MXene-polyvinylidene fluoride-based conductive carbon nanofiber-based dry ECG electrodes exhibit low skin contact impedance (40.5 kΩ cm2) and high-quality electrophysiological signals (signal-to-noise ratios = 23.4-32.8 dB). The developed system is utilized to accurately and wirelessly monitor the sweat glucose and ECG of a human subject engaged in physical exercise in real time.

Prognostic value of left atrium remodeling after primary percutaneous coronary intervention in patients with ST elevation acute myocardial infarction.

The purpose of this study is to assess the relationship between left atrial (LA) size and outcome after acute myocardial infarction (AMI) in patients undergoing primary percutaneous coronary intervention (PCI) and to evaluate dynamic changes in LA size during long-term follow-up. Echocardiographic analyses were performed on 253 AMI patients (174 male and 79 female, 65.4 ± 13.7 yr) undergoing PCI. These subjects were studied at baseline and at 12 months. Clinical follow-up were done at 30.8 ± 7.5 months. We assessed LA volume index (LAVI) at AMI-onset and at 12-month. Change of LAVI was an independent predictor of new onset of atrial fibrillation or hospitalization for heart failure (P = 0.002). Subjects who survived the 12-month period displayed an increased LAVI mean of 1.86 ± 4.01 mL/m(2) (from 26.1 ± 8.6 to 28.0 ± 10.1 mL/m(2), P < 0.001). The subject group that displayed an increased LAVI correlated with a low left ventricular ejection fraction, large left ventricle systolic and diastolic dimensions and an enlarged LA size. In conclusion, change of LAVI is useful parameter to predict subsequent adverse cardiac event in AMI patients. Post-AMI echocardiographic evaluation of LAVI provides important prognostic information that is significantly greater than that obtained from clinical and laboratory parameters alone.

Hysteresis-Free Double-Network Hydrogel-Based Strain Sensor for Wearable Smart Bioelectronics.

Hydrogel-based electronics have attracted substantial attention in the field of biological engineering, energy storage devices, and soft actuators due to their resemblance to living tissues, biocompatibility, tunable softness, and consolidated structures. However, combining the properties of quick resilience, hysteresis-free, and robust mechanical properties in physically cross-linked hydrogels is still a great challenge. Herein, we present a vinyl hybrid silica nanoparticle (VSNPs)/polyacrylamide (PAAm)/alginate double-network hydrogel-based strain sensor with the characteristics of quick resilience, hysteresis-free, and a low limit of detection (LOD). The physical cross-linking among PAAm chains and covalent cross-linking between PAAm, alginate, and N,N-methylenebisacrylamide chains promotes excellent mechanical properties. Moreover, the incorporation of VSNPs reinforces the mechanical strength by the dynamic cross-linking of the PAAm network to maintain the integrity of the hydrogel and works as a stress buffer to dissipate energy. The as-prepared hydrogel-based sensor exhibits a strain sensitivity (i.e., gauge factor) of 1.73 (up to 100% strain), a response time of 0.16 s, an ultra-low electrical hysteresis of 2.43%, and a low LOD of 0.4%. The outstanding properties of the hydrogel are further used to illustrate the utility of the sensor in e-skin, ranging from low-strain applications, such as carotid pulse and artificial sound detection, to large bending applications, such as sign language translations. In addition, an efficient and cost-effective synthesis of double-network hydrogel that can overcome the bottleneck of the electromechanical properties of single network hydrogel has potential prospects in soft actuators, tissue engineering, and various biomedical applications.

Multifunctional hybrid skin patch for wearable smart healthcare applications.

Recent advances in wearable patches have included various sensors to monitor either physiological signs, such as the heart rate and respiration rate, or metabolites. Nevertheless, most of these have focused only on a single physiological measurement at a time, which significantly inhibits the calibration of various biological signals and diagnostic facilities. In this study, a novel multifunctional hybrid skin patch was developed for the electrochemical analysis of sweat glucose levels and simultaneous monitoring of electrocardiograms (ECGs). Furthermore, pH and temperature sensors were co-integrated onto the same patch for the calibration of the glucose biosensor to prevent inevitable inhibition and weakening of enzyme activity due to changes in the sweat pH and temperature levels. The fabricated electrochemical glucose biosensor exhibited excellent linearity (R2 = 0.9986) and sensitivity (29.10 µA mM-1 cm-2), covering the normal range of human sweat. The potentiometric pH sensor displayed a good response with an excellent sensitivity of -77.81 mV/pH and high linearity (R2 = 0.991), indicating that it can distinguish variations in the typical pH range for human sweat. Furthermore, the P, QRS complex, and T peaks in the measured ECG waveforms could be clearly distinguished, indicating the reliability of the fabricated flexible dry electrodes for continuous monitoring. The fabricated skin patch overcomes the inconvenience of the mandatory attachment of multiple patches on the human body by fully integrating all the electrochemical and electrophysiological sensors on a single patch, thus facilitating advanced glycemic control and continuous ECG monitoring for smart management of chronic diseases and healthcare applications.

A nanocomposite-decorated laser-induced graphene-based multi-functional hybrid sensor for simultaneous detection of water contaminants.

Here, nanocomposite-decorated laser-induced graphene-based flexible hybrid sensor is newly developed for simultaneous detection of heavy metals, pesticides, and pH in freshwater. A series of deposition methods such as drop-casting, electroplating, and heating are adopted to modify and functionalize laser-induced graphene for engineering the high-performance detection at the individual sensor. A micro-dendritic structured bismuth@tin alloy inlaid on laser-induced graphene is prepared via a simple ex-situ electrodeposition method and thermal treatment for detecting heavy metals. The electrochemical performance is evaluated through the simultaneous determination of lead and cadmium ions at the optimized deposition potential of -1.2 V for 170 s, and a wide detection concentration range of 2-250 ppb and low detection limits (1.6 ppb and 0.9 ppb, respectively) are achieved. The pesticide sensor co-modified by zirconia nanoparticles and multilayered Ti3C2Tx-MXene is successfully implemented with a good linear performance for parathion after an optimal accumulation time of 120s. It realizes a low detection concentration range (0.1-5 ppb) with a detection limit of 0.06 ppb. Furthermore, a polyaniline/antimony/laser-induced graphene-based pH sensor is also integrated, showing an excellent sensitivity of -72.08 mV pH-1 in the pH range (2-9). They are also measured and characterized in different real water samples, exhibiting an acceptable detection performance, which provides promising applicability in the on-site monitoring of pollutants in the water environment.

A highly selective and stable cationic polyelectrolyte encapsulated black phosphorene based impedimetric immunosensor for Interleukin-6 biomarker detection.

Due to the insufficiency of binding sites for the immobilized recognition biomolecules on the immunosensing platform, cancer detection becomes challenging. Whereas, the degradation of black phosphorene (BP) in the presence of the environmental factors becomes a concerning issue for use in electrochemical sensing. In this study, BP is successfully encapsulated by polyallylamine (PAMI) to increase its stability as well as to enhance its electrochemical performance. The successful encapsulation of BP is ensured through X-ray Photoelectron spectroscopy and Raman spectroscopy, whereas the stability of black phosphorus is ensured by Zeta potential measurements and cyclic voltammetry tests. The developed BP-PAMI composite showed high stability in the ambient environment and exhibited improved electrochemical performances. The impedimetric immunosensor was developed on a BP-PAMI modified laser burned graphene (LBG) to detect interleukin-6 biomarkers using electrochemical impedance spectroscopy (EIS). Under the optimized parameters, the fabricated immunosensor demonstrated a wide linear range of 0.003-75 ng/mL, limit of detection (LOD) of 1 pg/mL. Based on the experimental analysis, the developed sensing strategy can be employed as an easy, disposable, cost-effective and highly selective point-of-care cancer detection. In addition, the developed technique can be applied broadly for detecting other biomarkers after treating with suitable biomolecules.