Thermal evolution of a polymer-nanoparticle binary mixture.

We experimentally probe the microscopic variations in a model polymer-nanoparticle (NP) binary mixture (mixture of polybutadiene and clay nanoplatelets) across a thermal evolution path for which Tevolution > Tg(polymer). The evolution of the NP dispersion, NP crystallinity, polymer chain-NP interface, and nature of polymer chain-NP interaction are mapped for a spectrum of temperatures and NP concentrations constrained by experiments. Multiple pieces of evidence indicate that thermal evolution does not influence the nature of interparticle dispersion and is also independent of NP concentration in the binary mixture. However, the NP crystalline order significantly reduces across the thermal evolution path. Thermal evolution induces a transition of a sharp polymer chain-NP interface to a diffuse interfacial layer. In contrast, an already diffuse polymer-NP interface existing in the binary mixture due to particle crowding at high NP concentrations undergoes no significant change in its nature across the evolution path. At all particle concentrations, thermal evolution changes the dominant interaction from polymer chain-polymer chain to polymer chain-NP. These insights aid in explaining the molecular origins of unique and anomalous behaviors shown by polymer-nanoparticle binary mixtures while undergoing thermal evolution.

Investigation of Dielectric and Mechanical Properties of Pretreated Natural Sunn Hemp Fiber-Reinforced Composite in Correlation with Macromolecular Structure of the Fiber.

The present study attempts to establish a correlation between the macromolecular parameters obtained from small angle X-ray scattering (SAXS) analysis of pretreated sunn hemp (Crotalaria juncea) fibers with the dielectric and mechanical properties of their composites. Sunn hemp fiber is pretreated chemically by dewaxing and alkalization methods and physically by microwave irradiation. The treatment effect is structurally investigated using a correlation function from SAXS data and correlated with the mechanical as well as electrical properties of composites. The macromolecular parameters are observed to be influenced by pretreatment methods. Macromolecular structural modifications are seen in dewaxed fiber (DSHC), fiber treated with 10% of alkali soaked for 6 h (10K6C), and fiber microwave irradiated with 800 watts for 6 min (800W6M), improving the mechanical as well as electric properties of the reinforced composites.

Anomalous toluene transport in model segmented polyurethane-urea/clay nanocomposites.

The kinetics of liquid solvent sorption in polymeric systems and their nanocomposites often deviate from normal Fickian behaviour. This needs to be understood and interpreted, in terms of their underlying mechanistic origins. In the present study, the results of time dependent toluene sorption measurements in model segmented polyurethane-urea/clay nanocomposites have been analysed at room temperature. The studies revealed pronounced S-shaped sorption curves and unusually higher swelling of the nanocomposites compared to the neat polyurethane-urea matrix. Dynamic mechanical analysis (DMA) and small angle X-ray scattering (SAXS) measurements on the nanocomposites in the dry and liquid toluene saturated state have been carried out. The DMA studies revealed a significant decrease in the α relaxation temperature and storage modulus of the nanocomposites in the swollen state compared to the dry samples. The SAXS results showed that the nanoclay dispersion morphology transformed from intercalation in the dry state to exfoliation in the swollen state and the interdomain distance between hard segments increased upon swelling. Thermodynamic analysis of the Flory-Huggins interaction parameter (χ) of nanocomposite/toluene systems revealed increasingly negative χ values with increased clay loading. These results imply a significant plasticization effect of toluene on the nanocomposites. An interpretation of these data, which relates the abovementioned results, is presented in the framework of differential swelling stress (DSS) induced deviation from Fickian transport characteristics. We expect that these findings and methods may provide new insight into the analysis of the solvent diffusion process in heterogeneous polymers and their nanocomposites.

High dielectric permittivity and improved mechanical and thermal properties of poly(vinylidene fluoride) composites with low carbon nanotube content: effect of composite processing on phase behavior and dielectric properties.

The composite processing technique and nanofiller concentration and its functionalization significantly alter the properties of polymer nanocomposites. To realize this, multi-walled carbon nanotubes (CNT) were dispersed in a poly(vinylidene fluoride) (PVDF) matrix at carefully selected CNT concentrations by two illustrious methods, such as solution-cast and melt-mixing. Notwithstanding the processing method, CNTs induced predominantly the γ-phase in PVDF, instead of the commonly obtained ß-phase upon nanofiller incorporation, and imparted significant improvements in dielectric properties. Acid-treatment of CNT improved its dispersion and interfacial adhesion significantly with PVDF, and induced a higher γ-phase content and better dielectric properties in PVDF as compared to pristine CNT. Further, the γ-phase content was found to be higher in solution-cast composites than that in melt-mixed counterparts, most likely due to solvent-induced crystallization in a controlled environment and slow solvent evaporation in the former case. However, interestingly, the melt-mixed composites showed a significantly higher dielectric constant at the onset of the CNT networked-structure as compared to the solution-cast composites. This suggests the possible role of CNT breakage during melt-mixing, which might lead to higher space-charge polarization at the polymer-CNT interface, and in turn an increased number of pseudo-microcapacitors in these composites than the solution-cast counterparts. Notably, PVDF with 0.13 vol% (volume fraction, f c  = 0.0013) of acid-treated CNTs, prepared by melt-mixing, displayed the relative permittivity of ∼217 and capacitance of ∼5430 pF, loss tangent of ∼0.4 at 1 kHz and an unprecedented figure of merit of ∼10(5). We suggest a simple hypothesis for the γ-phase formation and evolution of the high dielectric constant in these composites. Further, the high-dielectric composite film showed marked improvements in mechanical and thermal properties over the neat PVDF film. These composites with exceptional dielectric properties and concomitant improvement in mechanical and thermal properties offer a great promise for use in flexible and mechanically robust charge storage devices.

Solvent transport through hard-soft segmented polymer nanocomposites.

We conducted transport studies of a common solvent (toluene) in its condensed state, through a model hard-soft segmented polyurethane-clay nanocomposite. The solvent diffusivity is observed to be non-monotonic in a functional relationship with a filler volume fraction. In stark contrast, both classical tortuous path theory based geometric calculations and free volume measurements suggest the normally expected monotonic decrease in diffusivity with increase in clay volume fraction. Large deviations between experimentally observed diffusivity coefficients and those theoretically estimated from geometric theory are also observed. However, the equilibrium swelling of a nanocomposite as indicated by the solubility coefficient did not change. To gain an insight into the solvent interaction behavior, we conducted a pre- and post swollen segmented phase analysis of pure polymers and nanocomposites. We find that in a nanocomposite, the solvent has to interact with a filler altered hard-soft segmented morphology. In the altered phase separated morphology, the spatial distribution of thermodynamically segmented hard blocks in the continuous soft matrix becomes a strong function of filler concentration. Upon solvent interaction, this spatial distribution gets reoriented due to sorption and de-clustering. The results indicate strong non-barrier influences of nanoscale fillers dispersed in phase segmented block co-polymers, affecting solvent diffusivity through them. Based on pre- and post swollen morphological observations, we postulate a possible mechanism for the non-monotonic behaviour of solvent transport for hard-soft segmented co-polymers, in which the thermodynamic phase separation is influenced by the filler.

Electromagnetic interference shielding in 1-18 GHz frequency and electrical property correlations in poly(vinylidene fluoride)-multi-walled carbon nanotube composites.

Electromagnetic interference (EMI) shielding properties in the 1-18 GHz frequency range for multi-walled carbon nanotube (MWNT)-poly(vinylidene fluoride) (PVDF) composites are reported. A simple and gentle acid-treatment of MWNT showed a percolation threshold (PT) of 0.15 wt% in the PVDF matrix as against 0.35 wt% for unfunctionalized MWNT. Acid-treatment of MWNT significantly improves dispersion, interfacial adhesion with the matrix and the EMI shielding properties of PVDF composites. Further, the EMI shielding properties are correlated with the electrical properties. Using composite films of 0.3 mm thickness, the maximum shielding effectiveness (SET) values for 4 wt% unfunctionalized MWNT composites are found to be about 110, 45, 30, 26, and 58 dB for L (1-2 GHz), S (2-4 GHz), C (4-5.8 GHz), J (5.8-8 GHz), and X (8-12 GHz) bands, while the corresponding values for only 0.5 wt% acid functionalized MWNT composites are about 98, 45, 26, 19, and 47 dB, respectively. The electrical conductivity for both the cases is ∼10(-3) S cm(-1) and the weight contents of CNTs are higher than the PT for the respective composites. The comparable EMI SE and electrical conductivity values for both the composites at different weight fractions of CNTs suggest that there is a critical electrical conductivity above which the composites attain improved EMI shielding properties. Further, the shielding mechanism was found to be dominated by absorption loss. Therefore, the composites may also serve as a radar absorbing material.

Layer-by-layer assembled PVA/Laponite multilayer free-standing films and their mechanical and thermal properties.

Structural arrangements of nanoplatelets in a polymer matrix play an important role in determining their properties. In the present study, multilayered composite films of poly(vinyl alcohol) (PVA) with Laponite clay are assembled by layer-by-layer (LBL) deposition. The LBL films are found to be hydrated, flexible and transparent. A facile and solvent-free method-by depositing self-assembled monolayers (SMA) of a functional silane on substrates-is demonstrated for preparing free-standing LBL films. Evolution of nanostructures in LBL films is correlated with thermal and mechanical properties. A well-dispersed solvent-cast PVA/Laponite composite film is also studied for comparison. We found that structurally ordered LBL films with an intercalated nanoclay system exhibits tensile strength, modulus and toughness, which are significantly higher than that of the conventional nanocomposites with well-dispersed clay particles and that of pure PVA. This indicates that clay platelets are oriented in the applied stress direction, leading to efficient interfacial stress transfer. In addition, various grades of composite LBL films are prepared by chemical crosslinking and their mechanical properties are assessed. On account of these excellent properties, the LBL films may find potential use as optical and structural elements, and as humidity sensors.

Enhancement of hydrophilicity, biocompatibility and biodegradability of poly(ε-caprolactone) electrospun nanofiber scaffolds using poly(ethylene glycol) and poly(L-lactide-co-ε-caprolactone-co-glycolide) as additives for soft tissue engineering.

In this study, poly(ε-caprolactone) (PCL) has been blended with a more hydrophilic poly(ethylene glycol) (PEG) and with a biocompatible block-co-polymer: poly(L-lactide-co-ε-caprolactone-co-glycolide) (PLCG) in order to improve hydrophilicity, biocompatibility and biodegradability of PCL. PCL and the blend solutions were subjected to electrospinning to produce nanofiber scaffolds by the addition of only 1 wt% of PEG and PLCG either singly or in combination in PCL to retain the mechanical properties of the scaffolds. PCL-PEG-PLCG ternary and two binary (PCL-PEG and PCL-PLCG) blend nanofiber scaffolds have been prepared for comparison. The resulting nanofibers showed a smooth and flaw-free surface and the diameter of the nanofibers displayed a normal distribution. The PCL-PEG nanofiber scaffold showed improved hydrophilicity [water contact angle (WCA) ∼84°] over pristine PCL (WCA ∼127°); while PCL-PLCG and PCL-PEG-PLCG scaffolds exhibited absolute wetting by water, likely due to high porosity. In vitro biocompatibility studies using gingival mesenchymal stem cells (gMSCs) suggested that, both the PCL and the blend scaffolds were biocompatible supporting cell-viability and growth of gMSCs following their seeding on these scaffolds. Biodegradation studies in phosphate buffer solution showed that the addition of PEG and PLCG in PCL increased the weight loss of scaffolds with time, indicating higher extent of biodegradation in the blend scaffolds and the weight loss followed the power law curve with time.