Planar perovskite solar cells with long-term stability using ionic liquid additives.

Solar cells based on metal halide perovskites are one of the most promising photovoltaic technologies1-4. Over the past few years, the long-term operational stability of such devices has been greatly improved by tuning the composition of the perovskites5-9, optimizing the interfaces within the device structures10-13, and using new encapsulation techniques14,15. However, further improvements are required in order to deliver a longer-lasting technology. Ion migration in the perovskite active layer-especially under illumination and heat-is arguably the most difficult aspect to mitigate16-18. Here we incorporate ionic liquids into the perovskite film and thence into positive-intrinsic-negative photovoltaic devices, increasing the device efficiency and markedly improving the long-term device stability. Specifically, we observe a degradation in performance of only around five per cent for the most stable encapsulated device under continuous simulated full-spectrum sunlight for more than 1,800 hours at 70 to 75 degrees Celsius, and estimate that the time required for the device to drop to eighty per cent of its peak performance is about 5,200 hours. Our demonstration of long-term operational, stable solar cells under intense conditions is a key step towards a reliable perovskite photovoltaic technology.

Adduct-based p-doping of organic semiconductors.

Electronic doping of organic semiconductors is essential for their usage in highly efficient optoelectronic devices. Although molecular and metal complex-based dopants have already enabled significant progress of devices based on organic semiconductors, there remains a need for clean, efficient and low-cost dopants if a widespread transition towards larger-area organic electronic devices is to occur. Here we report dimethyl sulfoxide adducts as p-dopants that fulfil these conditions for a range of organic semiconductors. These adduct-based dopants are compatible with both solution and vapour-phase processing. We explore the doping mechanism and use the knowledge we gain to 'decouple' the dopants from the choice of counterion. We demonstrate that asymmetric p-doping is possible using solution processing routes, and demonstrate its use in metal halide perovskite solar cells, organic thin-film transistors and organic light-emitting diodes, which showcases the versatility of this doping approach.

Facile Synthesis of Stable and Highly Luminescent Methylammonium Lead Halide Nanocrystals for Efficient Light Emitting Devices.

Metal halide perovskites are promising candidates for use in light emitting diodes (LEDs), due to their potential for color tunable and high luminescence efficiency. While recent advances in perovskite-based light emitting diodes have resulted in external quantum efficiencies exceeding 12.4% for the green emitters, and infrared emitters based on 3 D/2D mixed dimensional perovskites have exceeded 20%, the external quantum efficiencies of the red and blue emitters still lag behind. A critical issue to date is creating highly emissive and stable perovskite emitters with the desirable emission band gap to achieve full-color displays and white LEDs. Herein, we report the preparation and characterization of a highly luminescent and stable suspension of cubic-shaped methylammonium lead triiodide (CH3NH3PbI3) perovskite nanocrystals, where we synthesize the nanocrystals via a ligand-assisted reprecipitation technique, using an acetonitrile/methylamine compound solvent system to solvate the ions and toluene as the antisolvent to induce crystallization. Through tuning the ratio of the ligands, the ligand to toluene ratio, and the temperature of the toluene, we obtain a solution of CH3NH3PbI3 nanocrystals with a photoluminescence quantum yield exceeding 93% and tunable emission between 660 and 705 nm. We also achieved red emission at 635 nm by blending the nanocrystals with bromide salt and obtained perovskite-based light emitting diodes with maximum electroluminescent external quantum efficiency of 2.75%.

Solution-Processed Cesium Hexabromopalladate(IV), Cs2PdBr6, for Optoelectronic Applications.

Lead halide perovskites are materials with excellent optoelectronic and photovoltaic properties. However, some hurdles remain prior to commercialization of these materials, such as chemical stability, phase stability, sensitivity to moisture, and potential issues due to the toxicity of lead. Here, we report a new type of lead-free perovskite related compound, Cs2PdBr6. This compound is solution processable, exhibits long-lived photoluminescence, and an optical band gap of 1.6 eV. Density functional theory calculations indicate that this compound has dispersive electronic bands, with electron and hole effective masses of 0.53 and 0.85 me, respectively. In addition, Cs2PdBr6 is resistant to water, in contrast to lead-halide perovskites, indicating excellent prospects for long-term stability. These combined properties demonstrate that Cs2PdBr6 is a promising novel compound for optoelectronic applications.

Controlling Nucleation and Growth of Metal Halide Perovskite Thin Films for High-Efficiency Perovskite Solar Cells.

Metal halide perovskite thin films can be crystallized via a broad range of solution-based routes. However, the quality of the final films is strongly dependent upon small changes in solution composition and processing parameters. Here, this study demonstrates that a fractional substitution of PbCl2 with PbI2 in the 3CH3 NH3 I:PbCl2 mixed-halide starting solution has a profound influence upon the ensuing thin-film crystallization. The presence of PbI2 in the precursor induces a uniform distribution of regular quadrilateral-shaped CH3 NH3 PbI3 perovskite crystals in as-cast films, which subsequently grow to form pinhole-free perovskite films with highly crystalline domains. With this new formulation of 3CH3 NH3 I:0.98PbCl2 :0.02PbI2 , this study achieves a 19.1% current-voltage measured power conversion efficiency and a 17.2% stabilized power output in regular planar heterojunction solar cells.

Microseconds, milliseconds and seconds: deconvoluting the dynamic behaviour of planar perovskite solar cells.

Perovskite solar cells (PSC) are shown to behave as coupled ionic-electronic conductors with strong evidence that the ionic environment moderates both the rate of electron-hole recombination and the band offsets in planar PSC. Numerous models have been presented to explain the behaviour of perovskite solar cells, but to date no single model has emerged that can explain both the frequency and time dependent response of the devices. Here we present a straightforward coupled ionic-electronic model that can be used to explain the large amplitude transient behaviour and the impedance response of PSC.

Identification of protein arginine N-methyltransferase 5 (PRMT5) as a novel interacting protein with the tumor suppressor protein RASSF1A.

The candidate tumor suppressor gene RASSF1A (Ras-association domain family 1, isoform A) is inactivated in many types of adult and childhood cancers. However, the mechanisms by which RASSF1A exerts tumor suppressive functions have yet to be elucidated. In this report, we sought to identify candidate proteins that interact with RASSF1A using proteomic screening. Using peptide mass fingerprinting, we identified protein arginine N-methyltransferase 5 (PRMT5), a type II protein arginine N-methyltransferase that monomethylates and symmetrically dimethylates arginine residues, as a novel protein that interacts with RASSF1A. The association between the two proteins was confirmed by co-immunoprecipitation and immunofluorescence staining. Co-expressing RASSF1A and PRMT5 led to a redistribution of PRMT5 from the cytosol to stabilized microtubules, where RASSF1A and PRMT5 became co-localized. Our results demonstrate that PRMT5 translocates to bundled microtubules on stabilization by RASSF1A expression. Our results show that the tumor suppressor RASSF1A interacts with PRMT5 in vivo and in vitro. Notably, this is the first demonstration of RASSF1A-dependent microtubule recruitment of PRMT5, suggesting a novel role for RASSF1A in the anchoring of cytosolic PRMT5 to microtubules.

Similar Structural Dynamics for the Degradation of CH3 NH3 PbI3 in Air and in Vacuum.

We investigate the degradation path of MAPbI3 (MA=methylammonium) films over flat TiO2 substrates at room temperature by means of X-ray diffraction, spectroscopic ellipsometry, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy. The degradation dynamics is found to be similar in air and under vacuum conditions, which leads to the conclusion that the occurrence of intrinsic thermodynamic mechanisms is not necessarily linked to humidity. The process has an early stage, which drives the starting tetragonal lattice in the direction of a cubic atomic arrangement. This early stage is followed by a phase change towards PbI2 . We describe how this degradation product is structurally coupled with the original MAPbI3 lattice through the orientation of its constituent PbI6 octahedra. Our results suggest a slight octahedral rearrangement after volatilization of HI+CH3 NH2 or MAI, with a relatively low energy cost. Our experiments also clarify why reducing the interfaces and internal defects in the perovskite lattice enhances the stability of the material.

Overexpression of SIP1 and downregulation of E-cadherin predict delayed neck metastasis in stage I/II oral tongue squamous cell carcinoma after partial glossectomy.

BACKGROUND: Patients with clinical stage I/II (T1-2N0M0) oral tongue squamous cell carcinoma (TSCC) usually undergo partial glossectomy alone. However, 14-48% of them develop delayed neck metastasis (DNM), which may lead to an unfavorable course. Recently epithelial-to-mesenchymal transition (EMT) has been thought to play a crucial role in cancer metastasis. The present study aimed to examine the associations of EMT-involved molecular factors and clinicopathological factors with DNM in stage I/II TSCC. METHODS: mRNA expression levels of E-cadherin and its transcriptional repressors (snail, SIP1, and twist) in 7 head and neck squamous cell carcinoma (HNSCC) cell lines were evaluated by quantitative real-time PCR. Clinicopathological parameters and immunohistochemical expressions of E-cadherin and its repressors were examined in surgical specimens of 37 stage I/II TSCC patients who underwent partial glossectomy alone. RESULTS: In HNSCC cells, E-cadherin expression was inversely correlated with SIP1 expression (P = 0.023). Univariate analysis of immunohistochemistry showed that overexpression of SIP1 and loss of E-cadherin were significantly correlated with DNM, although no inverse correlation was found between E-cadherin and its repressors. Multiple logistic regression analysis including clinicopathological and molecular factors revealed that overexpression of SIP1 (P = 0.005), loss of E-cadherin (P = 0.046), and vascular invasion (P = 0.024) were independently correlated with DNM. CONCLUSIONS: These results suggest that development of DNM in stage I/II TSCC is closely related to induction of EMT in primary tumor cells. Especially, SIP1 and E-cadherin are considered to be the possible markers for selecting patients at high risk of DNM.

Long-range charge carrier mobility in metal halide perovskite thin-films and single crystals via transient photo-conductivity.

Charge carrier mobility is a fundamental property of semiconductor materials that governs many electronic device characteristics. For metal halide perovskites, a wide range of charge carrier mobilities have been reported using different techniques. Mobilities are often estimated via transient methods assuming an initial charge carrier population after pulsed photoexcitation and measurement of photoconductivity via non-contact or contact techniques. For nanosecond to millisecond transient methods, early-time recombination and exciton-to-free-carrier ratio hinder accurate determination of free-carrier population after photoexcitation. By considering both effects, we estimate long-range charge carrier mobilities over a wide range of photoexcitation densities via transient photoconductivity measurements. We determine long-range mobilities for FA0.83Cs0.17Pb(I0.9Br0.1)3, (FA0.83MA0.17)0.95Cs0.05Pb(I0.9Br0.1)3 and CH3NH3PbI3-xClx polycrystalline films in the range of 0.3 to 6.7 cm2 V-1 s-1. We demonstrate how our data-processing technique can also reveal more precise mobility estimates from non-contact time-resolved microwave conductivity measurements. Importantly, our results indicate that the processing of polycrystalline films significantly affects their long-range mobility.

Development of a sphingosylphosphorylcholine detection system using RNA aptamers.

Sphingosylphosphorylcholine (SPC) is a lysosphingolipid that exerts multiple functions, including acting as a spasmogen, as a mitogenic factor for various types of cells, and sometimes as an inflammatory mediator. Currently, liquid chromatography/tandem mass spectrometry (LC/MS/MS) is used for the quantitation of SPC. However, because of the complicated procedures required it may not be cost effective, hampering its regular usage in a routine practical SPC monitoring. In this report, we have generated RNA aptamers that bind to SPC with high affinity using an in vitro selection procedure and developed an enzyme-linked aptamer assay system using the minimized SPC aptamer that can successfully distinguish SPC from the structurally related sphingosine 1-phosphate (S1P). This is the first case of the Systematic Evolution of Ligands by EXponential enrichment (SELEX) process being performed with a lysosphingolipid. The SPC aptamers would be valuable tools for the development of aptamer-based medical diagnosis and for elucidating the biological role of SPC.

Publisher Correction: Deciphering photocarrier dynamics for tuneable high-performance perovskite-organic semiconductor heterojunction phototransistors.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

A piperidinium salt stabilizes efficient metal-halide perovskite solar cells.

Longevity has been a long-standing concern for hybrid perovskite photovoltaics. We demonstrate high-resilience positive-intrinsic-negative perovskite solar cells by incorporating a piperidinium-based ionic compound into the formamidinium-cesium lead-trihalide perovskite absorber. With the bandgap tuned to be well suited for perovskite-on-silicon tandem cells, this piperidinium additive enhances the open-circuit voltage and cell efficiency. This additive also retards compositional segregation into impurity phases and pinhole formation in the perovskite absorber layer during aggressive aging. Under full-spectrum simulated sunlight in ambient atmosphere, our unencapsulated and encapsulated cells retain 80 and 95% of their peak and post-burn-in efficiencies for 1010 and 1200 hours at 60° and 85°C, respectively. Our analysis reveals detailed degradation routes that contribute to the failure of aged cells.

Antibody-specific aptamer-based PCR analysis for sensitive protein detection.

Nucleic acid amplification techniques were applied to the enzyme linked immunosorbent assay (ELISA) with an antibody-specific aptamer, R18. This novel detection system is a modification of the original immuno-polymerase chain reaction (immuno-PCR), but oligonucleotide-labeled antibodies are not required in the assay. This method is performed with the usual ELISA protocol, using an RNA aptamer for rabbit IgG instead of the conventional secondary antibody. After the assay plate was washed, quantitative reverse transcription (RT)-PCR was performed. Ribonuclease (RNase) inhibitors are not needed for this method. The detection limit of the quantitative RT-PCR is over 100 times more sensitive than the original ELISA method, even with the same sandwich-antibody combination. Only 1 mg of aptamer is sufficient for more than 10 million assays. This aptamer-based quantitative PCR successfully detected 16 attomoles (16 x 10(-18)) of vascular endothelial growth factor (VEGF). This is a cost-effective and easy method to increase the sensitivity of the rabbit antibody-based ELISA systems. The new method is referred to as immuno-aptamer PCR (iaPCR), to distinguish it from the original immuno-PCR.

Oxide Analogs of Halide Perovskites and the New Semiconductor Ba2AgIO6.

The past few years witnessed the rise of halide perovskites as prominent materials for a wide range of optoelectronic applications. However, oxide perovskites have a much longer history and are pivotal in many technological applications. As of today, a rational connection between these important materials is missing. Here, we explore this missing link and develop a novel concept of perovskite analogs, which led us to identify a new semiconductor, Ba2AgIO6. It exhibits an electronic band structure remarkably similar to that of our recently discovered halide double perovskite Cs2AgInCl6, but with a band gap in the visible range at 1.9 eV. We show that Ba2AgIO6 and Cs2AgInCl6 are analogs of the well-known transparent conductor BaSnO3. We synthesize Ba2AgIO6 following a low-temperature solution process, and we perform crystallographic and optical characterizations. Ba2AgIO6 is a cubic oxide double perovskite with a direct low gap, opening new opportunities in perovskite-based electronics optoelectronics and energy applications.

Deciphering photocarrier dynamics for tuneable high-performance perovskite-organic semiconductor heterojunction phototransistors.

Looking beyond energy harvesting, metal-halide perovskites offer great opportunities to revolutionise large-area photodetection technologies due to their high absorption coefficients, long diffusion lengths, low trap densities and simple processability. However, successful extraction of photocarriers from perovskites and their conversion to electrical signals remain challenging due to the interdependency of photogain and dark current density. Here we report hybrid hetero-phototransistors by integrating perovskites with organic semiconductor transistor channels to form either "straddling-gap" type-I or "staggered-gap" type-II heterojunctions. Our results show that gradual transforming from type-II to type-I heterojunctions leads to increasing and tuneable photoresponsivity with high photogain. Importantly, with a preferential edge-on molecular orientation, the type-I heterostructure results in efficient photocarrier cycling through the channel. Additionally, we propose the use of a photo-inverter circuitry to assess the phototransistors' functionality and amplification. Our study provides important insights into photocarrier dynamics and can help realise advanced device designs with "on-demand" optoelectronic properties.

Nonspiro, Fluorene-Based, Amorphous Hole Transporting Materials for Efficient and Stable Perovskite Solar Cells.

Novel nonspiro, fluorene-based, small-molecule hole transporting materials (HTMs) V1050 and V1061 are designed and synthesized using a facile three-step synthetic route. The synthesized compounds exhibit amorphous nature with a high glass transition temperature, a good solubility, and decent thermal stability. The planar perovskite solar cells (PSCs) employing V1050 generated an excellent power conversion efficiency of 18.3%, which is comparable to 18.9% obtained with the state-of-the-art Spiro-OMeTAD. Importantly, the devices based on V1050 and V1061 show better stability compared to devices based on Spiro-OMeTAD when aged without any encapsulation under uncontrolled humidity conditions (relative humidity around 60%) in the dark and under continuous full sun illumination.

VEGF-C/Flt-4 axis in tumor cells contributes to the progression of oral squamous cell carcinoma via upregulating VEGF-C itself and contactin-1 in an autocrine manner.

Tumor cell-derived vascular endothelial growth factor (VEGF)-C has been primarily implicated in promoting lymphangiogenesis by activating Flt-4 (VEGFR-3) expressed on lymphatic endothelial cells via a paracrine mechanism. Flt4 has also been shown to be expressed selectively in subsets of cancer cells. However, little is known about the functional role of VEGF-C/Flt4 signaling via an autocrine mechanism, as well as the clinicopathological implication of the VEGF-C/Flt4 axis and its downstream effector molecules, in head and neck squamous cell carcinoma (HNSCC), including oral squamous cell carcinoma (OSCC). In the present study, we detected Flt-4 expression selectively in several HNSCC cell lines by quantitative PCR, and its internalization reflecting receptor activation was confirmed by immunocytochemistry in SAS and HO1U1 cells. Flt-4 stimulation upregulated the expression of contactin-1 (CNTN-1, a neural cell adhesion molecule) and VEGF-C itself in SAS cells, while Flt-4 inhibition downregulated the expression of CNTN-1 in both SAS and HO1U1 cells and that of VEGF-C itself in SAS cells. In vitro cell proliferation and migration assays using SAS cells demonstrated that both cell proliferation and migration were promoted by Flt-4 stimulation, while those were suppressed by Flt-4 inhibition. Clinicopathological factors and immunohistochemical expression of Flt-4, VEGF-C, and CNTN-1 in tumor cells were evaluated using surgical specimens from patients with tongue squamous cell carcinoma. We found a significant correlation of CNTN-1 expression with both VEGF-C and Flt-4 expression, but not between VEGF-C and Flt-4. Multivariate logistic regression analysis revealed that T classification (P = 0.003), lymphatic invasion (P = 0.024), and Flt-4 expression in tumor cells (P = 0.046) were independently predictive of neck lymph node metastasis. These results suggest that the VEGF-C/Flt-4 axis in tumor cells enhances tumor cell proliferation and migration via upregulating the expression of VEGF-C itself and CNTN-1 in an autocrine manner, thereby contributing to cancer progression of OSCC, including neck metastasis. Hence, targeting the VEGF-C/Flt-4 axis in tumor cells can be an attractive therapeutic strategy for the treatment of cancer.

Complex formation between the vasopressin 1b receptor, ß-arrestin-2, and the µ-opioid receptor underlies morphine tolerance.

Chronic morphine exposure upregulates adenylate cyclase signaling and reduces analgesic efficacy, a condition known as opioid tolerance. Nonopioid neurotransmitters can enhance morphine tolerance, but the mechanism for this is poorly understood. We show that morphine tolerance was delayed in mice lacking vasopressin 1b receptors (V1bRs) or after administration of V1bR antagonist into the rostral ventromedial medulla, where transcripts for V1bRs and µ-opioid receptors are co-localized. Vasopressin increased morphine-binding affinity in cells expressing both V1bR and µ-opioid receptors. Complex formation among V1bR, ß-arrestin-2, and µ-opioid receptor resulted in vasopressin-mediated upregulation of ERK phosphorylation and adenylate cyclase sensitization. A leucine-rich segment in the V1bR C-terminus was necessary for the association with ß-arrestin-2. Deletion of this leucine-rich segment increased morphine analgesia and reduced vasopressin-mediated adenylate cyclase sensitization. These findings indicate that inhibition of µ-opioid-receptor-associated V1bR provides an approach for enhancing morphine analgesia without increasing analgesic tolerance.

Amorphous Hole-Transporting Material based on 2,2'-Bis-substituted 1,1'-Biphenyl Scaffold for Application in Perovskite Solar Cells.

Perovskite solar cells are considered a promising technology for solar-energy conversion, with power conversion efficiencies currently exceeding 20 %. In most of the reported devices, Spiro-OMeTAD is used for positive-charge extraction and transport layer. Although a number of alternative hole-transporting materials with different aromatic or heteroaromatic fragments have already been synthesized, a cheap and well-performing hole-transporting material is still in high demand. In this work, a two-step synthesis of a carbazole-based hole-transporting material is presented. Synthesized compounds exhibited amorphous nature, good solubility and thermal stability. The perovskite solar cells employing the newly synthesized material generated a power conversion efficiency of 16.5 % which is slightly lower than that obtained with Spiro-OMeTAD (17.5 %). The low-cost synthesis and high performance makes our hole-transport material promising for applications in perovskite-based optoelectronic devices.