Long-range order enabled stability in quantum dot light-emitting diodes.

Light-emitting diodes (LEDs) based on perovskite quantum dots (QDs) have produced external quantum efficiencies (EQEs) of more than 25% with narrowband emission1,2, but these LEDs have limited operating lifetimes. We posit that poor long-range ordering in perovskite QD films-variations in dot size, surface ligand density and dot-to-dot stacking-inhibits carrier injection, resulting in inferior operating stability because of the large bias required to produce emission in these LEDs. Here we report a chemical treatment to improve the long-range order of perovskite QD films: the diffraction intensity from the repeating QD units increases three-fold compared with that of controls. We achieve this using a synergistic dual-ligand approach: an iodide-rich agent (aniline hydroiodide) for anion exchange and a chemically reactive agent (bromotrimethylsilane) that produces a strong acid that in situ dissolves smaller QDs to regulate size and more effectively removes less conductive ligands to enable compact, uniform and defect-free films. These films exhibit high conductivity (4 × 10-4 S m-1), which is 2.5-fold higher than that of the control, and represents the highest conductivity recorded so far among perovskite QDs. The high conductivity ensures efficient charge transportation, enabling red perovskite QD-LEDs that generate a luminance of 1,000 cd m-2 at a record-low voltage of 2.8 V. The EQE at this luminance is more than 20%. Furthermore, the stability of the operating device is 100 times better than previous red perovskite LEDs at EQEs of more than 20%.

Regulating surface potential maximizes voltage in all-perovskite tandems.

The open-circuit voltage (VOC) deficit in perovskite solar cells is greater in wide-bandgap (over 1.7 eV) cells than in perovskites of roughly 1.5 eV (refs. 1,2). Quasi-Fermi-level-splitting measurements show VOC-limiting recombination at the electron-transport-layer contact3-5. This, we find, stems from inhomogeneous surface potential and poor perovskite-electron transport layer energetic alignment. Common monoammonium surface treatments fail to address this; as an alternative, we introduce diammonium molecules to modify perovskite surface states and achieve a more uniform spatial distribution of surface potential. Using 1,3-propane diammonium, quasi-Fermi-level splitting increases by 90 meV, enabling 1.79 eV perovskite solar cells with a certified 1.33 V VOC and over 19% power conversion efficiency (PCE). Incorporating this layer into a monolithic all-perovskite tandem, we report a record VOC of 2.19 V (89% of the detailed balance VOC limit) and over 27% PCE (26.3% certified quasi-steady state). These tandems retained more than 86% of their initial PCE after 500 h of operation.

Suppressed phase segregation for triple-junction perovskite solar cells.

The tunable bandgaps and facile fabrication of perovskites make them attractive for multi-junction photovoltaics1,2. However, light-induced phase segregation limits their efficiency and stability3-5: this occurs in wide-bandgap (>1.65 electron volts) iodide/bromide mixed perovskite absorbers, and becomes even more acute in the top cells of triple-junction solar photovoltaics that require a fully 2.0-electron-volt bandgap absorber2,6. Here we report that lattice distortion in iodide/bromide mixed perovskites is correlated with the suppression of phase segregation, generating an increased ion-migration energy barrier arising from the decreased average interatomic distance between the A-site cation and iodide. Using an approximately 2.0-electron-volt rubidium/caesium mixed-cation inorganic perovskite with large lattice distortion in the top subcell, we fabricated all-perovskite triple-junction solar cells and achieved an efficiency of 24.3 per cent (23.3 per cent certified quasi-steady-state efficiency) with an open-circuit voltage of 3.21 volts. This is, to our knowledge, the first reported certified efficiency for perovskite-based triple-junction solar cells. The triple-junction devices retain 80 per cent of their initial efficiency following 420 hours of operation at the maximum power point.

Anion optimization for bifunctional surface passivation in perovskite solar cells.

Pseudo-halide (PH) anion engineering has emerged as a surface passivation strategy of interest for perovskite-based optoelectronics; but until now, PH anions have led to insufficient defect passivation and thus to undesired deep impurity states. The size of the chemical space of PH anions (>106 molecules) has so far limited attempts to explore the full family of candidate molecules. We created a machine learning workflow to speed up the discovery process using full-density functional theory calculations for training the model. The physics-informed machine learning model allowed us to pinpoint promising molecules with a head group that prevents lattice distortion and anti-site defect formation, and a tail group optimized for strong attachment to the surface. We identified 15 potential bifunctional PH anions with the ability to passivate both donors and acceptors, and through experimentation, discovered that sodium thioglycolate was the most effective passivant. This strategy resulted in a power-conversion efficiency of 24.56% with a high open-circuit voltage of 1.19 volts (24.04% National Renewable Energy Lab-certified quasi-steady-state) in inverted perovskite solar cells. Encapsulated devices maintained 96% of their initial power-conversion energy during 900 hours of one-sun operation at the maximum power point.

Organic Polar Crystals, Second Harmonic Generation, and Piezoelectric Effects from Heteroadamantanes in the Space Group R3m.

Polar crystalline materials, a subset of the non-centrosymmetric materials, are highly sought after. Their symmetry properties make them pyroelectric and also piezoelectric and capable of second-harmonic generation (SHG). For SHG and piezoelectric applications, metal oxides are commonly used. The advantages of oxides are durability and hardness - downsides are the need for high-temperature synthesis/processing and often the need to include toxic metals. Organic polar crystals, on the other hand, can avoid toxic metals and can be amenable to solution-state processing. While the vast majority of polar organic molecules crystallize in non-polar space groups, we found that both 7-chloro-1,3,5-triazaadamantane, for short Cl-TAA, and also the related Br-TAA (but not I-TAA) form polar crystals in the space group R3m, easily obtained from dichloromethane solution. Measurements confirm piezoelectric and SHG properties for Cl-TAA and Br-TAA. When the two species are crystallized together, solid solutions form, suggesting that properties of future materials can be tuned continuously.

Bifunctional Electron-Transporting Agent for Red Colloidal Quantum Dot Light-Emitting Diodes.

Indium phosphide (InP) quantum dots have enabled light-emitting diodes (LEDs) that are heavy-metal-free, narrow in emission linewidth, and physically flexible. However, ZnO/ZnMgO, the electron-transporting layer (ETL) in high-performance red InP/ZnSe/ZnS LEDs, suffers from high defect densities, quenches luminescence when deposited on InP, and induces performance degradation that arises due to trap migration from the ETL to the InP emitting layer. We posited that the formation of Zn2+ traps on the outer ZnS shell, combined with sulfur and oxygen vacancy migration between ZnO/ZnMgO and InP, may account for this issue. We synthesized therefore a bifunctional ETL (CNT2T, 3',3'″,3'″″-(1,3,5-triazine-2,4,6-triyl)tris(([1,1'-biphenyl]-3-carbonitrile)) designed to passivate Zn2+ traps locally and in situ and to prevent vacancy migration between layers: the backbone of the small molecule ETL contains a triazine electron-withdrawing unit to ensure sufficient electron mobility (6 × 10-4 cm2 V-1 s-1), and the star-shaped structure with multiple cyano groups provides effective passivation of the ZnS surface. We report as a result red InP LEDs having an EQE of 15% and a luminance of over 12,000 cd m-2; this represents a record among organic-ETL-based red InP LEDs.

Wide-Bandgap Perovskite Quantum Dots in Perovskite Matrix for Sky-Blue Light-Emitting Diodes.

The epitaxial growth of a perovskite matrix on quantum dots (QDs) has enabled the emergence of efficient red light-emitting diodes (LEDs) because it unites efficient charge transport with strong surface passivation. However, the synthesis of wide-band gap (Eg) QD-in-matrix heterostructures has so far remained elusive in the case of sky-blue LEDs. Here, we developed CsPbBr3 QD-in-perovskite matrix solids that enable high luminescent efficiency and spectral stability with an optical Eg of over 2.6 eV. We screened alloy candidates that modulate the perovskite Eg and allow heteroepitaxy, seeking to implement lattice-matched type-I band alignment. Specifically, we introduced a CsPb1-xSrxBr3 matrix, in which alloying with Sr2+ increased the Eg of the perovskite and minimized lattice mismatch. We then developed an approach to passivation that would overcome the hygroscopic nature of Sr2+. We found that bis(4-fluorophenyl)phenylphosphine oxide strongly coordinates with Sr2+ and provides steric hindrance to block H2O, a finding obtained by combining molecular dynamics simulations with experimental results. The resulting QD-in-matrix solids exhibit enhanced air- and photo-stability with efficient charge transport from the matrix to the QDs. LEDs made from this material exhibit an external quantum efficiency of 13.8% and a brightness exceeding 6000 cd m-2.

Adsorption of Hydrophilic Silica Nanoparticles at Oil-Water Interfaces with Reversible Emulsion Stabilization by Ion Partitioning.

Adsorption of particles at oil-water interfaces is the basis of Pickering emulsions, which are common in nature and industry. For hydrophilic anionic particles, electrostatic repulsion and the absence of wetting inhibit spontaneous adsorption and limit the scope of materials that can be used in emulsion-based applications. Here, we explore how adding ions that selectively partition in the two fluid phases changes the interfacial electric potential and drives particle adsorption. We add oil-soluble tetrabutyl ammonium perchlorate (TBAP) to the nonpolar phase and Ludox silica nanoparticles or silica microparticles to the aqueous phase. We find a well-defined threshold TBAP concentration, above which emulsions are stable for months. This threshold increases with the particle concentration and with the oil's dielectric constant. Adding NaClO4 salt to water increases the threshold and causes spontaneous particle desorption and droplet coalescence even without agitation. The results are explained by a model based on the Poisson-Boltzmann theory, which predicts that the perchlorate anions (ClO4-) migrate into the water phase and leave behind a net positive charge in the oil. Our results show how a large class of inorganic hydrophilic, anionic nanoparticles can be used to stabilize emulsions in a reversible and stimulus-responsive way, without surface modifications.

One-Step Synthesis of SnI2·(DMSO)x Adducts for High-Performance Tin Perovskite Solar Cells.

Contemporary thin-film photovoltaic (PV) materials contain elements that are scarce (CIGS) or regulated (CdTe and lead-based perovskites), a fact that may limit the widespread impact of these emerging PV technologies. Tin halide perovskites utilize materials less stringently regulated than the lead (Pb) employed in mainstream perovskite solar cells; however, even today's best tin-halide perovskite thin films suffer from limited carrier diffusion length and poor film morphology. We devised a synthetic route to enable in situ reaction between metallic Sn and I2 in dimethyl sulfoxide (DMSO), a reaction that generates a highly coordinated SnI2·(DMSO)x adduct that is well-dispersed in the precursor solution. The adduct directs out-of-plane crystal orientation and achieves a more homogeneous structure in polycrystalline perovskite thin films. This approach improves the electron diffusion length of tin-halide perovskite to 290 ± 20 nm compared to 210 ± 20 nm in reference films. We fabricate tin-halide perovskite solar cells with a power conversion efficiency of 14.6% as certified in an independent lab. This represents a ∼20% increase compared to the previous best-performing certified tin-halide perovskite solar cells. The cells outperform prior earth-abundant and heavy-metal-free inorganic-active-layer-based thin-film solar cells such as those based on amorphous silicon, Cu2ZnSn(S/Se)4 , and Sb2(S/Se)3.

Improved charge extraction in inverted perovskite solar cells with dual-site-binding ligands.

Inverted (pin) perovskite solar cells (PSCs) afford improved operating stability in comparison to their nip counterparts but have lagged in power conversion efficiency (PCE). The energetic losses responsible for this PCE deficit in pin PSCs occur primarily at the interfaces between the perovskite and the charge-transport layers. Additive and surface treatments that use passivating ligands usually bind to a single active binding site: This dense packing of electrically resistive passivants perpendicular to the surface may limit the fill factor in pin PSCs. We identified ligands that bind two neighboring lead(II) ion (Pb2+) defect sites in a planar ligand orientation on the perovskite. We fabricated pin PSCs and report a certified quasi-steady state PCE of 26.15 and 24.74% for 0.05- and 1.04-square centimeter illuminated areas, respectively. The devices retain 95% of their initial PCE after 1200 hours of continuous 1 sun maximum power point operation at 65°C.

Sterically Suppressed Phase Segregation in 3D Hollow Mixed-Halide Wide Band Gap Perovskites.

Band gap tuning in mixed-halide perovskites enables efficient multijunction solar cells and LEDs. However, these wide band gap perovskites, which contain a mixture of iodide and bromide ions, are known to phase segregate under illumination, introducing voltage losses that limit stability. Previous studies have employed inorganic perovskites, halide alloys, and grain/interface passivation to minimize halide segregation, yet photostability can be further advanced. By focusing on the role of halide vacancies in anion migration, one expects to be able to erect local barriers to ion migration. To achieve this, we employ a 3D "hollow" perovskite structure, wherein a molecule that is otherwise too large for the perovskite lattice is incorporated. The amount of hollowing agent, ethane-1,2-diammonium dihydroiodide (EDA), varies the density of the hollow sites. Photoluminescence measurements reveal that 1% EDA in the perovskite bulk can stabilize a 40% bromine mixed-halide perovskite at 1 sun illumination intensity. These, along with capacitance-frequency measurements, suggest that hollow sites limit the mobility of the halide vacancies.

Large piezoelectric response in a Jahn-Teller distorted molecular metal halide.

Piezoelectric materials convert between mechanical and electrical energy and are a basis for self-powered electronics. Current piezoelectrics exhibit either large charge (d33) or voltage (g33) coefficients but not both simultaneously, and yet the maximum energy density for energy harvesting is determined by the transduction coefficient: d33*g33. In prior piezoelectrics, an increase in polarization usually accompanies a dramatic rise in the dielectric constant, resulting in trade off between d33 and g33. This recognition led us to a design concept: increase polarization through Jahn-Teller lattice distortion and reduce the dielectric constant using a highly confined 0D molecular architecture. With this in mind, we sought to insert a quasi-spherical cation into a Jahn-Teller distorted lattice, increasing the mechanical response for a large piezoelectric coefficient. We implemented this concept by developing EDABCO-CuCl4 (EDABCO = N-ethyl-1,4-diazoniabicyclo[2.2.2]octonium), a molecular piezoelectric with a d33 of 165 pm/V and g33 of ~2110 × 10-3 V m N-1, one that achieved thusly a combined transduction coefficient of 348 × 10-12 m3 J-1. This enables piezoelectric energy harvesting in EDABCO-CuCl4@PVDF (polyvinylidene fluoride) composite film with a peak power density of 43 µW/cm2 (at 50 kPa), the highest value reported for mechanical energy harvesters based on heavy-metal-free molecular piezoelectric.

Self-assembled monolayer-based blue perovskite LEDs.

Blue perovskite light-emitting diodes (LEDs) have shown external quantum efficiencies (EQEs) of more than 10%; however, devices that emit in the true blue-those that accord with the emission wavelength required for Rec. 2100 primary blue-have so far been limited to EQEs of ~6%. We focused here on true blue emitting CsPbBr3 colloidal nanocrystals (c-NCs), finding in early studies that they suffer from a high charge injection barrier, a problem exacerbated in films containing multiple layers of nanocrystals. We introduce a self-assembled monolayer (SAM) active layer that improves charge injection. We identified a bifunctional capping ligand that simultaneously enables the self-assembly of CsPbBr3 c-NCs while passivating surface traps. We report, as a result, SAM-based LEDs exhibit a champion EQE of ~12% [CIE of (0.132, 0.069) at 4.0 V with a luminance of 11 cd/m2], and 10-fold-enhanced operating stability relative to the best previously reported Rec. 2100-blue perovskite LEDs.

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells.

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. We found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi-steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T85 at maximum power point under 1-sun illumination.

Germanium silicon oxide achieves multi-coloured ultra-long phosphorescence and delayed fluorescence at high temperature.

Colour-tuned phosphors are promising for advanced security applications such as multi-modal anti-counterfeiting and data encryption. The practical adoption of colour-tuned phosphors requires these materials to be responsive to multiple stimuli (e.g., excitation wavelength, excitation waveform, and temperature) and exhibit excellent materials stability simultaneously. Here we report germanium silicon oxide (GSO) - a heavy-metal-free inorganic phosphor - that exhibits colour-tuned ultra-long phosphorescence and delayed fluorescence across a broad temperature range (300 - 500 K) in air. We developed a sol-gel processing strategy to prepare amorphous oxides containing homogeneously dispersed Si and Ge atoms. The co-existence of Ge and Si luminescent centres (LC) leads to an excitation-dependent luminescence change across the UV-to-visible region. GSO exhibits Si LC-related ultra-long phosphorescence at room-temperature and thermally activated delayed fluorescence at temperatures as high as 573 K. This long-lived PL is sensitized via the energy transfer from Ge defects to Si LCs, which provides PL lifetime tunability for GSO phosphors. The oxide scaffold of GSO offers 500-day materials stability in air; and 1-week stability in strong acidic and basic solutions. Using GSO/polymer hybrids, we demonstrated colour-tuned security tags whose emission wavelength and lifetime can be controlled via the excitation wavelength, and temperature, indicating promise in security applications.

Multication perovskite 2D/3D interfaces form via progressive dimensional reduction.

Many of the best-performing perovskite photovoltaic devices make use of 2D/3D interfaces, which improve efficiency and stability - but it remains unclear how the conversion of 3D-to-2D perovskite occurs and how these interfaces are assembled. Here, we use in situ Grazing-Incidence Wide-Angle X-Ray Scattering to resolve 2D/3D interface formation during spin-coating. We observe progressive dimensional reduction from 3D to n = 3 → 2 → 1 when we expose (MAPbBr3)0.05(FAPbI3)0.95 perovskites to vinylbenzylammonium ligand cations. Density functional theory simulations suggest ligands incorporate sequentially into the 3D lattice, driven by phenyl ring stacking, progressively bisecting the 3D perovskite into lower-dimensional fragments to form stable interfaces. Slowing the 2D/3D transformation with higher concentrations of antisolvent yields thinner 2D layers formed conformally onto 3D grains, improving carrier extraction and device efficiency (20% 3D-only, 22% 2D/3D). Controlling this progressive dimensional reduction has potential to further improve the performance of 2D/3D perovskite photovoltaics.

Passivation of the Buried Interface via Preferential Crystallization of 2D Perovskite on Metal Oxide Transport Layers.

The open-circuit voltage (Voc ) of perovskite solar cells is limited by non-radiative recombination at perovskite/carrier transport layer (CTL) interfaces. 2D perovskite post-treatments offer a means to passivate the top interface; whereas, accessing and passivating the buried interface underneath the perovskite film requires new material synthesis strategies. It is posited that perovskite ink containing species that bind strongly to substrates can spontaneously form a passivating layer with the bottom CTL. The concept using organic spacer cations with rich NH2 groups is implemented, where readily available hydrogens have large binding affinity to under-coordinated oxygens on the metal oxide substrate surface, inducing preferential crystallization of a thin 2D layer at the buried interface. The passivation effect of this 2D layer is examined using steady-state and time-resolved photoluminescence spectroscopy: the 2D interlayer suppresses non-radiative recombination at the buried perovskite/CTL interface, leading to a 72% reduction in surface recombination velocity. This strategy enables a 65 mV increase in Voc for NiOx based p-i-n devices, and a 100 mV increase in Voc for SnO2 -based n-i-p devices. Inverted solar cells with 20.1% power conversion efficiency (PCE) for 1.70 eV and 22.9% PCE for 1.55 eV bandgap perovskites are demonstrated.

Dimensional Mixing Increases the Efficiency of 2D/3D Perovskite Solar Cells.

2D/3D heterojunction perovskite solar cells have demonstrated superior efficiency and stability compared to their fully 3D counterparts. Previous studies have focused on producing 2D layers containing predominantly n = 1 perovskite quantum wells. In this report we demonstrate a technique to introduce dimensional mixing into the 2D layer, and we show that this leads to more efficient devices relative to controls. Simulations suggest that the improvements are due to a reduction in trap state density and superior band alignment between the 3D/2D perovskite and the hole-transporting layer.