Application of Sulfur and Peroxide Curing Systems for Cross-Linking of Rubber Composites Filled with Calcium Lignosulfonate.

Calcium lignosulfonate in different loadings was applied to the rubber matrix based on EPDM. A sulfur curing system, organic peroxide, and a combination of organic peroxide with two coagent types were used for cross-linking of rubber compounds. The work was focused on the investigation of filler content and curing system composition in the curing process, cross-link density, morphology, and physical-mechanical properties of composites. The achieved results demonstrated that the curing parameters of rubber compounds cured with the sulfur system were significantly different from those cured with peroxide systems. There was also an observed different influence of curing systems composition on cross link density, though in all cases, the degree of cross-linking showed a decreasing trend with increasing content of lignosulfonate. The tensile strength of the composites cured with sulfur system and organic peroxide was comparable, regardless of lignosulfonate loading. This points to the application of both curing systems in cross-linking of rubber compounds with biopolymer filler. However, the introduction of coagents in peroxide vulcanization led to the improvement of adhesion and compatibility between the rubber and the filler on the filler-rubber interface. This subsequently resulted in the improvement of the tensile characteristics of composites. The introduction of organic peroxide in combination with coagent seems to be a very simple and efficient way for the preparation of biopolymer-filled composites with applicable physical-mechanical properties.

In Vitro Characterization of Poly(Lactic Acid)/ Poly(Hydroxybutyrate)/ Thermoplastic Starch Blends for Tissue Engineering Application.

Complex in vitro characterization of a blended material based on Poly(Lactic Acid), Poly(Hydroxybutyrate), and Thermoplastic Starch (PLA/PHB/TPS) was performed in order to evaluate its potential for application in the field of tissue engineering. We focused on the biological behavior of the material as well as its mechanical and morphological properties. We also focused on the potential of the blend to be processed by the 3D printer which would allow the fabrication of the custom-made scaffold. Several blends recipes were prepared and characterized. This material was then studied in the context of scaffold fabrication. Scaffold porosity, wettability, and cell-scaffold interaction were evaluated as well. MTT test and the direct contact cytotoxicity test were applied in order to evaluate the toxic potential of the blended material. Biocompatibility studies were performed on the human chondrocytes. According to our results, we assume that material had no toxic effect on the cell culture and therefore could be considered as biocompatible. Moreover, PLA/PHB/TPS blend is applicable for 3D printing. Printed scaffolds had highly porous morphology and were able to absorb water as well. In addition, cells could adhere and proliferate on the scaffold surface. We conclude that this blend has potential for scaffold engineering.

Beta-glucan and arabinogalactan-based xerogels for abuse-deterrent opioid formulations.

Novel polysaccharide hydrogels based on Methocel and beta-glucan or arabinogalactan and corresponding xerogels were prepared and described. Phase stability of hydrogels was confirmed over multiple freeze-thaw cycles. Binary beta-glucan:Methocel hydrogels showed the highest freeze-thaw stability in terms of their syneresis. The viscosity of binary hydrogels was further increased by adding water-soluble resin. Freeze drying of polysaccharide gels yields xerogels suitable as abuse-deterrent vehicles for opioid delivery. The xerogels were characterized by infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, scanning electron microscopy and by their swelling behavior. As a model opioid, tramadol hydrochloride formulations were prepared with various xerogel matrices and dissolution-release profiles were determined. The xerogel matrix acts as a functional excipient that forms a viscous gel barrier with decreased rate of tramadol release. Moreover, slower drug release with no dose dumping is observed in the presence of ethanol. The release kinetics demonstrated that hydrophilic gels with beta-glucan or arabinogalactan are effective for controlling and prolonging the drug release for 12 h which could reduce the required number of administrations.

Reinforcement of Rubber Magnetic Composites with Zinc Salts of Acrylic and Methacrylic Acids.

Strontium ferrite was compounded with acrylonitrile butadiene rubber to prepare rubber magnetic composites. For cross-linking of the prepared materials, peroxide curing systems consisting of dicumyl peroxide as curing agent and zinc salts of acrylic and methacrylic acids as co-agents were used. The amount of strontium ferrite was kept constant in all experiments, while the main objective of the work was to investigate the composition of curing system and both types of co-agents on the cross-linking, physical-mechanical, dynamic and magnetic properties of the rubber magnets. The results showed that the change in composition of curing system has significant influence on cross-link density and properties of the tested composite materials. With an increasing amount of zinc based co-agents, significant improvement of tensile strength was achieved. The application of zinc based co-agents in peroxide vulcanization of rubber magnetic composites leads to the preparation of rubber magnets with not only good magnetic properties, but also with improved physical-mechanical characteristics.

Use of Irradiated Polymers after Their Lifetime Period.

This article deals with the study of the utilisation of irradiated HDPE products after their end-of-life cycle. Today, polymer waste processing is a matter of evermore intensive discussion. Common thermoplastic waste recycling-especially in the case of wastes with a defined composition-is generally well-known-and frequently used. On the contrary, processing cross-linked plastics is impossible to do in the same way as with virgin thermoplastics-mainly due to the impossibility of remelting them. The possibility of using waste in the form of grit or a powder, made from cross-linked High Density PolyEthylene (rHDPEx) products, after their end-of-life cycle, as a filler for virgin Low Density PolyEthylene (LDPE) was tested in a matrix. It was found that both the mechanical behaviour and processability of new composites with an LDPE matrix, with rHDPEx as a filler, depend-to a high degree-on the amount of the filler. The composite can be processed up to 60% of the filler content. The Polymer Mixture Fluidity dropped significantly, in line with the amount of filler, while the mechanical properties, on the other hand, predominantly grew with the increasing amount of rHDPEx.

Polymorphisms in equine immune response genes and their associations with infections.

Polymorphic markers identified in the horse genes encoding the interleukin 12 p40 subunit, interferon gamma, tumor necrosis factor receptor 1, and inducible nitric oxide synthase were identified and tested, along with additional markers, for associations with two important horse infections: Rhodococcus equi and Lawsonia intracellularis. Eight immune response-related and 14 microsatellite loci covering 12 out of 31 equine autosomes were used for the association analysis. Markers located on horse Chromosomes Eca10 and 15 were significantly associated with the presence of high numbers of R. equi in transtracheal aspirates. Significant associations of markers located on Eca9, 15, and 21 with fecal shedding of Lawsonia intracellularis were found. Marginal associations with tumor necrosis factor alpha, interferon gamma, and other genes suggested that variations in immune response-related genes could underlie the phenotypic variation observed.