Homogenizing out-of-plane cation composition in perovskite solar cells.

Perovskite solar cells with the formula FA1-xCsxPbI3, where FA is formamidinium, provide an attractive option for integrating high efficiency, durable stability and compatibility with scaled-up fabrication. Despite the incorporation of Cs cations, which could potentially enable a perfect perovskite lattice1,2, the compositional inhomogeneity caused by A-site cation segregation is likely to be detrimental to the photovoltaic performance of the solar cells3,4. Here we visualized the out-of-plane compositional inhomogeneity along the vertical direction across perovskite films and identified the underlying reasons for the inhomogeneity and its potential impact for devices. We devised a strategy using 1-(phenylsulfonyl)pyrrole to homogenize the distribution of cation composition in perovskite films. The resultant p-i-n devices yielded a certified steady-state photon-to-electron conversion efficiency of 25.2% and durable stability.

Electron Accumulation Induced by Electron Injection-Incomplete Discharge on NiFe LDH for Enhanced Oxygen Evolution Reaction.

Optimizing the local electronic structure of electrocatalysts can effectively lower the energy barrier of electrochemical reactions, thus enhancing the electrocatalytic activity. However, the intrinsic contribution of the electronic effect is still experimentally unclear. In this work, the electron injection-incomplete discharge approach to achieve the electron accumulation (EA) degree on the nickel-iron layered double hydroxide (NiFe LDH) is proposed, to reveal the intrinsic contribution of EA toward oxygen evolution reaction (OER). Such NiFe LDH with EA effect results in only 262 mV overpotential to reach 50 mA cm-2, which is 51 mV-lower compared with pristine NiFe LDH (313 mV), and reduced Tafel slope of 54.8 mV dec-1 than NiFe LDH (107.5 mV dec-1). Spectroscopy characterizations combined with theoretical calculations confirm that the EA near concomitant Vo can induce a narrower energy gap and lower thermodynamic barrier to enhance OER performance. This study clarifies the mechanism of the EA effect on OER activity, providing a direct electronic structure modulation guideline for effective electrocatalyst design.

Grain boundary defect engineering in rutile iridium oxide boosts efficient and stable acidic water oxidation.

PEMWE is considered a promising technology for coupling with renewable energy sources to achieve clean hydrogen production. However, constrained by the sluggish kinetics of the anodic OER and the acidic abominable environment render the grand challenges in developing the active and stable OER electrocatalyst, leading to low efficiency of PEMWE. Herein, we develop the rutile-type IrO2 nanoparticles with abundant grain boundaries and the continuous nanostructure through the joule heating and sacrificial template method. DFT calculations verified that grain boundaries can modulate the electronic structure of Ir sites and optimize the adsorption of oxygen intermediates, resulting in the accelerated kinetics. The 350-IrO2 affords a rapid OER process with 20 times higher mass activity (0.61 A mgIr-1) than the commercial IrO2 at 1.50 V vs. RHE. Benefiting from the reduced overpotential and the preservation of the stable rutile structure, 350-IrO2 exhibits the stability of 200 h test at 10 mA cm-2 with only trace decay of 11.8 mV. Moreover, the assembled PEMWE with anode 350-IrO2 catalyst outputs the current density up to 2 A cm-2 with only 1.84 V applied voltage, long-term operation for 100 h without obvious performance degradation at 1 A cm-2.

Single-Atom 3d Transition Metals on SnO2 as Model Cell for Conversion Mechanism: Revealing Thermodynamic Catalytic Effects on Enhanced Na Storage of Heterostructures.

Since the discovery in 2000, conversion-type materials have emerged as a promising negative-electrode candidate for next-generation batteries with high capacity and tunable voltage, limited by low reversibility and severe voltage hysteresis. Heterogeneous construction stands out as a cost-effective and efficient approach to reducing reaction barriers and enhancing energy density. However, the second term introduced by conventional heterostructure inevitably complicates the electrochemical analysis and poses great challenges to harvesting systematic insights and theoretical guidance. A model cell is designed and established herein for the conversion reactions between Na and TMSA-SnO2, where TMSA-SnO2 represents single atom modification of eight different 3d transition elements (V, Cr, Mn, Fe, Co, Ni, Cu or Zn). Such a model unit fundamentally eliminates the interference from the second phase and thus enables independent exploration of activation manifestations of the heterogeneous architecture. For the first time, a thermodynamically dependent catalytic effect is proposed and verified through statistical data analysis. The mechanism behind the unveiled catalytic effect is further elucidated by which the active d orbitals of transition metals weaken the surface covalent bonds and lower the reaction barriers. This research provides both theoretical insights and practical demonstrations of the advanced heterogeneous electrodes.

Ion sieving in graphene oxide membranes via cationic control of interlayer spacing.

Graphene oxide membranes-partially oxidized, stacked sheets of graphene-can provide ultrathin, high-flux and energy-efficient membranes for precise ionic and molecular sieving in aqueous solution. These materials have shown potential in a variety of applications, including water desalination and purification, gas and ion separation, biosensors, proton conductors, lithium-based batteries and super-capacitors. Unlike the pores of carbon nanotube membranes, which have fixed sizes, the pores of graphene oxide membranes-that is, the interlayer spacing between graphene oxide sheets (a sheet is a single flake inside the membrane)-are of variable size. Furthermore, it is difficult to reduce the interlayer spacing sufficiently to exclude small ions and to maintain this spacing against the tendency of graphene oxide membranes to swell when immersed in aqueous solution. These challenges hinder the potential ion filtration applications of graphene oxide membranes. Here we demonstrate cationic control of the interlayer spacing of graphene oxide membranes with ångström precision using K+, Na+, Ca2+, Li+ or Mg2+ ions. Moreover, membrane spacings controlled by one type of cation can efficiently and selectively exclude other cations that have larger hydrated volumes. First-principles calculations and ultraviolet absorption spectroscopy reveal that the location of the most stable cation adsorption is where oxide groups and aromatic rings coexist. Previous density functional theory computations show that other cations (Fe2+, Co2+, Cu2+, Cd2+, Cr2+ and Pb2+) should have a much stronger cation-π interaction with the graphene sheet than Na+ has, suggesting that other ions could be used to produce a wider range of interlayer spacings.

Spectroscopic Study of the Behavior of Mo(VI) and W(VI) Polyanions in Sulfuric-Phosphoric Acid Mixtures.

The solution chemistry of Mo(VI) and W(VI) in mixtures of sulfuric and phosphoric acids is relevant to the development of practicable hydrometallurgical processes for the recovery and separation of these two elements from low-grade scheelite ores. The behavior of Mo(VI) and W(VI) in such mixtures has been studied using X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS), nuclear magnetic resonance (NMR), and small-angle X-ray scattering (SAXS) spectroscopies, along with electrospray ionization time-of-flight mass spectrometry (ESI-TOF-MS). Where applicable, these techniques have produced a self-consistent picture of the similarities and differences between the chemical speciation of Mo(VI) and W(VI) as functions of solution composition, mostly at a constant phosphorous/metal (P/M; M = Mo(VI) or W(VI)) ratio of ∼1. In dilute acidic media (0.02 mol·kg-1 H+, without H2SO4), Mo(VI) exists mostly (∼60%) as P2Mo5O236- with the remaining ∼40% as ß-Mo8O264-. Under the same conditions, W(VI) is largely present as NaPW11O396- (∼80%) and P2W5O236- (∼10%), with the remainder probably occurring as isopolytungstates such as W12O4212- and some tungstophosphate dimers such as P2W18O626-. At higher acid concentrations (≲5 mol·kg-1 H2SO4), polymeric Mo(VI) anions are broken down to form the oxocations MoO22+ and Mo2O52+ and their protonated forms, with the dimers becoming increasingly dominant at higher acidities (∼80% in 5 mol·kg-1 H2SO4). In stark contrast, W(VI) polyanions do not decompose at higher acidities but instead form (∼70% in 0.6 mol·kg-1 H2SO4) a Keggin ion, PW12O403-. Further acidification with H2SO4 results in the agglomeration of this Keggin ion, forming clusters of about 50 and 100 Å in diameter that ultimately produce crystalline precipitates, which could be identified in part by their X-ray diffraction patterns. Possible application of these findings to the hydrometallurgical separation of Mo and W using acidic solutions is briefly discussed, based on a limited number of batch solvent extractions.

Transformation Pathway from CdSe Magic-Size Clusters with Absorption Doublets at 373/393†nm to Clusters at 434/460†nm.

Divergent interpretations have appeared in the literature regarding the structural nature and evolutionary behavior for photoluminescent CdSe nanospecies with sharp doublets in optical absorption. We report a comprehensive description of the transformation pathway from one CdSe nanospecies displaying an absorption doublet at 373/393 nm to another species with a doublet at 433/460 nm. These two nanospecies are zero-dimensional (0D) magic-size clusters (MSCs) with 3D quantum confinement, and are labeled dMSC-393 and dMSC-460, respectively. Synchrotron-based small-angle X-ray scattering (SAXS) returns a radius of gyration of 0.92 nm for dMSC-393 and 1.14 nm for dMSC-460, and indicates that both types are disc shaped with the exponent of the SAXS form factor equal to 2.1. The MSCs develop from their unique counterpart precursor compounds (PCs), which are labeled PC-393 and PC-460, respectively. For the dMSC-393 to dMSC-460 transformation, the proposed PC-enabled pathway is comprised of three key steps, dMSC-393 to PC-393 (Step 1), PC-393 to PC-460 (Step 2 involving monomer addition), and PC-460 to dMSC-460 (Step 3). The present study provides a framework for understanding the PC-based evolution of MSCs and how PCs enable transformations between MSCs.

Room-Temperature Formation Pathway for CdTeSe Alloy Magic-Size Clusters.

Little is known about the pathway of room-temperature formation of ternary CdTeSe magic-size clusters (MSCs) obtained by mixing binary CdTe and CdSe induction period samples containing binary precursor compounds (PCs) of MSCs, monomers (Ms), and fragments (Fs). Also, unestablished are dispersion effects that occur when as-mixed samples (without incubation) are placed in toluene (Tol) and octylamine (OTA) mixtures. The resulting ternary MSCs, exhibiting a sharp optical absorption peak at 399 nm, are labelled CdTeSe MSC-399, and their PCs are referred to as CdTeSe PC-399. When the amount of OTA is relatively small, single-ensemble MSC-399 evolved without either binary CdTe or CdSe MSCs. When the OTA amount is relatively large, CdTe MSC-371 appeared initially and then disappeared, while single-ensemble MSC-399 developed more deliberately. The larger the OTA amount, the more slowly these changes proceeded. The substitution reaction of CdTe PC + CdSe M/F↔CdTeSe PC-399 + CdTe M/F is proposed to be rate-determining for the MSC-399 formation in a Tol and OTA mixture. This study provides further understanding of the transformation pathway between MSCs.

In Situ Probing of the Particle-Mediated Mechanism of WO3 -Networked Structures Grown inside Confined Mesoporous Channels.

Nanocasting, using ordered mesoporous silica or carbon as a hard template, has enormous potential for preparing novel mesoporous materials with new structures and compositions. Although a variety of mesoporous materials have been synthesized in recent years, the growth mechanism of nanostructures in a confined space, such as mesoporous channels, is not well understood, which hampers the controlled synthesis and further application of mesoporous materials. Here, the nucleation and growth of WO3 -networked mesostructures within an ordered mesoporous matrix, using an in situ transmission electron microscopy heating technique and in situ synchrotron small-angle X-ray scattering spectroscopy, are probed. It is found that the formation of WO3 mesostructures involves a particle-mediated transformation and coalescence mechanism. The liquid-like particle-mediated aggregation and mesoscale transformation process can occur in ≈10 nm confined mesoporous channels, which is completely unexpected. The detailed mechanistic study will be of great help for experimental design and to exploit a variety of mesoporous materials for diverse applications, such as catalysis, absorption, separation, energy storage, biomedicine, and nanooptics.

Performance on absolute scattering intensity calibration and protein molecular weight determination at BL16B1, a dedicated SAXS beamline at SSRF.

The optical system and end-station of bending-magnet beamline BL16B1, dedicated to small-angle X-ray scattering (SAXS) at the Shanghai Synchrotron Radiation Facility, is described. Constructed in 2009 and upgraded in 2013, this beamline has been open to users since May 2009 and supports methodologies including SAXS, wide-angle X-ray scattering (WAXS), simultaneous SAXS/WAXS, grazing-incidence small-angle X-ray scattering (GISAXS) and anomalous small-angle X-ray scattering (ASAXS). Considering that an increasing necessity for absolute calibration of SAXS intensity has been recognized in in-depth investigations, SAXS intensity is re-stated according to the extent of data processing, and the absolute intensity is suggested to be a unified presentation of SAXS data in this article. Theory with a practical procedure for absolute intensity calibration is established based on BL16B1, using glass carbon and water as primary and secondary standards, respectively. The calibration procedure can be completed in minutes and shows good reliability under different conditions. An empirical line of scale factor estimation is also established for any specific SAXS setup at the beamline. Beamline performance on molecular weight (MW) determination is provided as a straightforward application and verification of the absolute intensity calibration. Results show good accuracy with a deviation of less than 10% compared with the known value, which is also the best attainable accuracy in recent studies using SAXS to measure protein MW. Fast MW measurement following the demonstrated method also enables an instant check or pre-diagnosis of the SAXS performance to improve the data acquisition.

Improved Glass Transition Temperature towards Thermal Stability via Thiols Solvent Additive versus DIO in Polymer Solar Cells.

The halogen-free solvent additive, 1,4-butanedithiol (BT) has been incorporated into PTB7-Th:PC71 BM, leading to higher power conversion efficiency (PCE) value as well as substantially enhanced thermal stability, as compared with the traditional 1,8-diiodooctane (DIO) additive. More importantly, the improved thermal stability after processing with BT contributes to a higher glass transition temperature (Tg ) of PTB7-Th, as determined by dynamic mechanical analysis. After thermal annealing at 130 °C in nitrogen atmosphere for 30 min, the PCE of the specimen processed with BT reduces from 9.3% to 7.1%, approaching to 80% of its original value. In contrast, the PCE of specimens processed with DIO seriously depresses from 8.3% to 3.8%. These findings demonstrate that smart utilization of low-boiling-point solvent additive is an effective and practical strategy to overcome thermal instability of organic solar cells via enhancing the Tg of donor polymer.

Characteristics of secondary inorganic aerosol and sulfate species in size-fractionated aerosol particles in Shanghai.

Sulfate, nitrate and ammonium (SNA) are the dominant species in secondary inorganic aerosol, and are considered an important factor in regional haze formation. Size-fractionated aerosol particles for a whole year were collected to study the size distribution of SNA as well as their chemical species in Shanghai. SNA mainly accumulated in fine particles and the highest average ratio of SNA to particulate matter (PM) was observed to be 47% in the fine size fraction (0.49-0.95 µm). Higher sulfur oxidation ratio and nitrogen oxidation ratio values were observed in PM of fine size less than 0.95 µm. Ion balance calculations indicated that more secondary sulfate and nitrate would be generated in PM of fine size (0.49-0.95 µm). Sulfur K-edge X-ray absorption near-edge structure (XANES) spectra of typical samples were analyzed. Results revealed that sulfur mainly existed as sulfate with a proportion (atomic basis) more than 73% in all size of PM and even higher at 90% in fine particles. Sulfate mainly existed as (NH4)2SO4 and gypsum in PM of Shanghai. Compared to non-haze days, a dramatic increase of (NH4)2SO4 content was found in fine particles on haze days only, which suggested the promoting impact of (NH4)2SO4 on haze formation. According to the result of air mass backward trajectory analysis, more (NH4)2SO4 would be generated during the periods of air mass stagnation. Based on XANES, analysis of sulfate species in size-fractionated aerosol particles can be an effective way to evaluate the impact of sulfate aerosols on regional haze formation.

Highly efficient electrochemical ammonia synthesis via nitrate reduction over metallic Cu phase coupling sulfion oxidation.

Electrochemical nitrate reduction reaction (NO3RR) is a promising technology for ammonia production and denitrification of wastewater. Its application is seriously restricted by the development of the highly active and selective electrocatalyst and a rational electrolysis system. Here, we constructed an efficient electrochemical ammonia production process via nitrate reduction on the metallic Cu electrocatalyst when coupled with anodic sulfion oxidation reaction (SOR). The synthesized Cu catalyst delivers an excellent NH3 Faradaic efficiency of 96.0 % and a NH3 yield of 0.391 mmol h-1 cm-2 at -0.2 V vs. reversible hydrogen electrode, which mainly stem from the more favorable conversion of NO2 - to NH3 on Cu0. Importantly, the well-designed electrolysis system with cathodic NO3RR and anodic SOR achieves a dramatically reduced cell voltage of 0.8 V at 50 mA cm-2 in comparison with the one with anodic oxygen evolution reaction (OER) of 1.9 V. This work presents an effective strategy for the energy-saving ammonia production via constructing effective nitrate reduction catalyst and replacing the OER with SOR while removing the pollutants including nitrate and sulfion.

Highly Stable Layered Coordination Polymer Electrocatalyst toward Efficient CO2 -to-CH4 Conversion.

Cu2+ -based materials, a class of promising catalysts for the electrocatalytic carbon dioxide reduction reaction (CO2 RR) to value-added chemicals, usually undergo inevitable and uncontrollable reorganization processes during the reaction, resulting in catalyst deactivation or the new active sites formation and bringing great challenges to exploring their structure-performance relationships. Herein, a facile strategy is reported for constructing Cu2+ and 3, 4-ethylenedioxythiophene (EDOT) coordination to stabilize Cu2+ ions to prepare a novel layered coordination polymer (CuPEDOT). CuPEDOT enables selective reduction of CO2 to CH4 with 62.7% Faradaic efficiency at the current density of 354 mA cm-2 in a flow cell, and the catalyst is stable for at least 15 h. In situ spectroscopic characterization and theoretical calculations reveal that CuPEDOT catalyst can maintain the Cu2+ -EDOT coordination structurally stable in CO2 RR and significantly promote the further hydrogenation of *CO intermediates, favoring the formation of CH4 instead of dimerization to C2 products. The strong coordination between EDOT and Cu2+ prevents the reduction of Cu2+ ions during CO2 RR. The finding of this work provides a new perspective on designing molecularly stable, highly active catalysts for CO2 RR.

Strengthening the Synergy between Oxygen Vacancies in Electrocatalysts for Efficient Glycerol Electrooxidation.

Defect-engineered bimetallic oxides exhibit high potential for the electrolysis of small organic molecules. However, the ambiguity in the relationship between the defect density and electrocatalytic performance makes it challenging to control the final products of multi-step multi-electron reactions in such electrocatalytic systems. In this study, controllable kinetics reduction is used to maximize the oxygen vacancy density of a Cu─Co oxide nanosheet (CuCo2O4 NS), which is used to catalyze the glycerol electrooxidation reaction (GOR). The CuCo2O4-x NS with the highest oxygen-vacancy density (CuCo2O4-x-2) oxidizes C3 molecules to C1 molecules with selectivity of almost 100% and a Faradaic efficiency of ≈99%, showing the best oxidation performance among all the modified catalysts. Systems with multiple oxygen vacancies in close proximity to each other synergistically facilitate the cleavage of C─C bonds. Density functional theory calculations confirm the ability of closely spaced oxygen vacancies to facilitate charge transfer between the catalyst and several key glycolic-acid (GCA) intermediates of the GOR process, thereby facilitating the decomposition of C2 intermediates to C1 molecules. This study reveals qualitatively in tuning the density of oxygen vacancies for altering the reaction pathway of GOR by the synergistic effects of spatial proximity of high-density oxygen vacancies.

Manipulation of Electron Spins with Oxygen Vacancy on Amorphous/Crystalline Composite-Type Catalyst.

By substituting the oxygen evolution reaction (OER) with the anodic urea oxidation reaction (UOR), it not only reduces energy consumption for green hydrogen generation but also allows purification of urea-rich wastewater. Spin engineering of the d orbital and oxygen-containing adsorbates has been recognized as an effective pathway for enhancing the performance of electrocatalysts. In this work, we report the fabrication of a bifunctional electrocatalyst composed of amorphous RuO2-coated NiO ultrathin nanosheets (a-RuO2/NiO) with abundant amorphous/crystalline interfaces for hydrogen evolution reaction (HER) and UOR. Impressively, only 1.372 V of voltage is required to attain a current density of 10 mA cm-2 over a urea electrolyzer. The increased oxygen vacancies in a-RuO2/NiO by incorporation of amorphous RuO2 enhance the total magnetization and entail numerous spin-polarized electrons during the reaction, which speeds up the UOR reaction kinetics. The density functional theory study reveals that the amorphous/crystalline interfaces promote charge-carrier transfer, and the tailored d-band center endows the optimized adsorption of oxygen-generated intermediates. This kind of oxygen vacancy induced spin-polarized electrons toward boosting HER and UOR kinetics and provides a reliable reference for exploration of advanced electrocatalysts.

Sulfur speciation and bioaccumulation in camphor tree leaves as atmospheric sulfur indicator analyzed by synchrotron radiation XRF and XANES.

Analyzing and understanding the effects of ambient pollution on plants is getting more and more attention as a topic of environmental biology. A method based on synchrotron radiation X-ray fluorescence and X-ray absorption near edge structure spectroscopy was established to analyze the sulfur concentration and speciation in mature camphor tree leaves (CTLs), which were sampled from 5 local fields in Shanghai, China. Annual SO2 concentration, SO4(2-) concentration in atmospheric particulate, SO4(2-) and sulfur concentration in soil were also analyzed to explore the relationship between ambient sulfur sources and the sulfur nutrient cycling in CTLs. Total sulfur concentration in mature camphor tree leaves was 766-1704 mg/kg. The mainly detected sulfur states and their corresponding compounds were +6 (sulfate, include inorganic sulfate and organic sulfate), +5.2 (sulfonate), +2.2 (suloxides), +0.6 (thiols and thiothers), +0.2 (organic sulfides). Total sulfur concentration was strongly correlated with sulfate proportion with a linear correlation coefficient up to 0.977, which suggested that sulfur accumulated in CTLs as sulfate form. Reduced sulfur compounds (organic sulfides, thiols, thioethers, sulfoxide and sulfonate) assimilation was sufficed to meet the nutrient requirement for growth at a balanced level around 526 mg/kg. The sulfate accumulation mainly caused by atmospheric sulfur pollution such as SO2 and airborne sulfate particulate instead of soil contamination. From urban to suburb place, sulfate in mature CTLs decreased as the atmospheric sulfur pollution reduced, but a dramatic increase presented near the seashore, where the marine sulfate emission and maritime activity pollution were significant. The sulfur concentration and speciation in mature CTLs effectively represented the long-term biological accumulation of atmospheric sulfur pollution in local environment.

Room-Temperature Evolution of Ternary CdTeS Magic-Size Clusters Exhibiting Sharp Absorption Peaking at 381 nm.

Colloidal semiconductor ternary CdTeS magic-size clusters (MSCs) have not been reported. Here, we present the first synthesis of CdTeS MSCs at room temperature and our understanding of the evolution pathway. The MSCs exhibit sharp optical absorption peaking at 381 nm and are labeled MSC-381. CdTeS MSC-381 evolves when pre-nucleation-stage samples of binary CdTe and CdS that do not contain quantum dots (QDs) are separately prepared and then mixed and incubated at room temperature. We propose that CdTeS MSC-381 evolves from its precursor compound (PC) via quasi-isomerization. Synchrotron-based small-angle X-ray scattering suggests that PCs/MSCs of CdTe and CdTeS are similar in sizes. We propose further that the CdTeS PC forms from the substitution reaction between the CdTe PC and the CdS monomer/fragment (Mo/Fr). The present study paves the way to the room-temperature evolution of ternary MSCs and provides an in-depth understanding of the PC to MSC transformation.

Transformation Pathway from CdSe Nanoplatelets with Absorption Doublets at 373/393 nm to Nanoplatelets at 434/460 nm.

For those colloidal semiconductor CdSe nanospecies that exhibit sharp optical absorption doublets, different explanations have appeared in the literature regarding their morphological nature and formation, with no consensus reached. Here, we discuss the transformation pathway in two types of CdSe nanoplatelets (NPLs), from NPL-393 to NPL-460, exhibiting absorption doublets at 373/393 and 433/460 nm, respectively. Synchrotron-based small/wide-angle X-ray scattering (SAXS/WAXS) was performed to monitor the in situ transformation associated with the temperature. Combining the results of SAXS/WAXS, optical spectroscopy, and transmission electron microscopy, we propose that the transformation pathway experiences corresponding magic-sized clusters (MSCs), which display similar optical properties but with zero-dimensional structure. From stacked NPL-393 to stacked NPL-460, the transformation goes through sequentially individual NPL-393, MSC-393, MSC-460, and individual NPL-460 at their corresponding characteristic temperature. The present findings provide compelling evidence that both MSCs and their assembled NPLs exhibit similar optical absorption.

Folded network and structural transition in molten tin.

The fundamental relationships between the structure and properties of liquids are far from being well understood. For instance, the structural origins of many liquid anomalies still remain unclear, but liquid-liquid transitions (LLT) are believed to hold a key. However, experimental demonstrations of LLTs have been rather challenging. Here, we report experimental and theoretical evidence of a second-order-like LLT in molten tin, one which favors a percolating covalent bond network at high temperatures. The observed structural transition originates from the fluctuating metallic/covalent behavior of atomic bonding, and consequently a new paradigm of liquid structure emerges. The liquid structure, described in the form of a folded network, bridges two well-established structural models for disordered systems, i.e., the random packing of hard-spheres and a continuous random network, offering a large structural midground for liquids and glasses. Our findings provide an unparalleled physical picture of the atomic arrangement for a plethora of liquids, shedding light on the thermodynamic and dynamic anomalies of liquids but also entailing far-reaching implications for studying liquid polyamorphism and dynamical transitions in liquids.