RESUMEN
The advent of 3D surgical technology has revolutionized personalized medicine, enabling the development of tailored solutions for individual patients. This technical note presents the application of 3D technology in designing a customized chin guard using flexible 3D resin. The process involves surface scanning the lower facial region of a polytraumatized patient with a structured-light surface 3D scanner, generating a detailed point cloud. The acquired data undergoes meticulous processing within an specific professional software, including erasing unwanted portions, aligning frames, and mesh consolidation. Subsequently, the mesh is exported as an STL file and further refined using a 3D mesh management software. A customized chin support is designed for the specific patient's needs, exported in STL format, and 3D printed using a stereolithography (SLA) printer with Flexible 80A resin. Post-printing procedures involve washing and curing to ensure biocompatibility and optimal mechanical characteristics. The resultant customized chin guard, attached to elastic support straps, offers a precise fit to the patient's anatomy, enhancing comfort and allowing for extended wear. This innovative approach addresses the challenge of surgical intraoral wound dehiscence in a polytraumatized patient, showcasing the potential of 3D technology in personalized medical solutions for complex cases. Key words:Surface scanner, 3D surgery, customized surgery, chinstrap.
RESUMEN
Maxillofacial surgery planning has been improved by technological advances in 3D printing. The use of customized cutting and positioning guides allows intraoperative reproduction of pre-planned osteotomy cuts, resulting in increased surgical accuracy, reduced surgical time and improved esthetic and functional outcomes. Our paper presents a new method for creating and printing in-house cutting and positioning guides. A computer program (Brainlab iPlan) was used to segment the mandible for three-dimensional planning from imported conventional computed tomography (CT) scans. The virtual model of the mandible was printed on a stereolithography (SLA) 3D printer and a reconstruction plate was adapted to the printed model. The surface of the model and the screw-retained plate was scanned using a structured light surface 3D scanner (Artec Eva). The obtained scan of the jaw and plate in position was processed and transformed into an STL file. Free software (Autodesk Meshmixer) superimposes the initial jaw on the scanned jaw with the plate, designing a customized hybrid cutting guide that allows accurate intraoperative positioning, knowing the exact position of the reconstruction plate screws in the jaw. The total design, fabrication and 3D printing time for the in-house hybrid guide was 595 min. The average total printing cost was EUR 16. We found the technique to be simple and repeatable. We present and describe here a novel and simple technique for in-house 3D printed positioning and cutting guide system which can be applied to overall maxillofacial area. In cases of mandibular reconstruction, this protocol guarantees an adequate esthetic and functional result. Key words:Oral cancer, 3D surgery, CAD/CAM, personalized medicine, surgical guides, in house.
RESUMEN
The purpose of this study was to perform a quantitative and qualitative validation of a soft tissue simulation pipeline for orthognathic surgery planning, necessary for clinical use. Simulation results were retrospectively obtained in 10 patients who underwent orthognathic surgery. Quantitatively, error was measured at 9 anatomical landmarks for each patient and different types of comparative analysis were performed considering two mesh resolutions, clinically accepted error, simulation time and error measured by means of percentage of the whole surface. Qualitatively, evaluation and binary questions were asked to two surgeons, both before and after seeing the actual surgical outcome, and their answers were compared. Finally, the quantitative and qualitative results were compared to check if these two types of validation are correlated. The quantitative results were accurate, with greater errors corresponding to gonions and lower lip. Qualitatively, surgeons answered similarly mostly and their evaluations improved when seeing the actual outcome of the surgery. The quantitative validation was not correlated to the qualitative validation. In this study, quantitative and qualitative validations were performed and compared, and the need to carry out both types of analysis in validation studies of soft tissue simulation software for orthognathic surgery planning was proved.
RESUMEN
(1) Background: In recent years, three-dimensional (3D) templates have replaced traditional two-dimensional (2D) templates as visual guides during intra-operative carving of the autogenous cartilage framework in microtia reconstruction. This study aims to introduce a protocol of the fabrication of patient-specific, 3D printed and sterilizable auricular models for autogenous auricular reconstruction. (2) Methods: The patient's unaffected ear was captured with a high-resolution surface 3D scan (Artec Eva) and post-processed in order to obtain a clean surface model (STL format). In the next step, the ear was digitally mirrored, segmented and separated into its component auricle parts for reconstruction. It was disassembled into helix, antihelix, tragus and base and a physical model was 3D printed for each part. Following this segmentation, the cartilage was carved in the operating room, based on the models. (3) Results: This segmentation technique facilitates the modeling and carving of the scaffold, with adequate height, depth, width and thickness. This reduces both the surgical time and the amount of costal cartilage used. (4) Conclusions: This segmentation technique uses surface scanning and 3D printing to produce sterilizable and patient-specific 3D templates.