Use of a Novel Extremophilic Xylanase for an Environmentally Friendly Industrial Bleaching of Kraft Pulps.

Xylanases can boost pulp bleachability in Elemental Chlorine Free (ECF) processes, but their industrial implementation for producing bleached kraft pulps is not straightforward. It requires enzymes to be active and stable at the extreme conditions of alkalinity and high temperature typical of this industrial process; most commercial enzymes are unable to withstand these conditions. In this work, a novel highly thermo and alkaline-tolerant xylanase from Pseudothermotoga thermarum was overproduced in E. coli and tested as a bleaching booster of hardwood kraft pulps to save chlorine dioxide (ClO2) during ECF bleaching. The extremozyme-stage (EXZ) was carried out at 90 °C and pH 10.5 and optimised at lab scale on an industrial oxygen-delignified eucalyptus pulp, enabling us to save 15% ClO2 to reach the mill brightness, and with no detrimental effect on paper properties. Then, the EXZ-assisted bleaching sequence was validated at pilot scale under industrial conditions, achieving 25% ClO2 savings and reducing the generation of organochlorinated compounds (AOX) by 18%, while maintaining pulp quality and papermaking properties. Technology reproducibility was confirmed with another industrial kraft pulp from a mix of hardwoods. The new enzymatic technology constitutes a realistic step towards environmentally friendly production of kraft pulps through industrial integration of biotechnology.

Versatile characterization of thiol-functionalized printed metal electrodes on flexible substrates for cheap diagnostic applications.

BACKGROUND: Cheap, reliable, point-of-care diagnostics is a necessity for the growing and aging population of the world. Paper substrate and printing method, combined together, are the cheapest possible method for generating high-volume diagnostic sensor platforms. Electrical transduction tools also minimize the cost and enhance the simplicity of the devices. METHODS: Standard surface characterization techniques, namely contact angle measurements, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to analyze the growth of the organic thiol layers on top of the printed metal electrodes on paper substrates. The results were compared with those obtained by impedimetric electrical characterization method. RESULTS: This article reports the fabrication and characterization of printed metal electrodes and their functionalization by organic layers on paper and plastic substrates for biosensing and diagnostic applications. Impedimetric measurement is proposed as a simple, yet elegant, method of characterization of the organic layer growth. CONCLUSIONS: Very good correlation was observed between the results of organic layer growth from different measurement methods, justifying the use of paper as a substrate, printing as a method for fabricating metal and organic layers and impedance as a suitable measurement method for hand-held diagnostic devices. GENERAL SIGNIFICANCE: This result paves the way for the fabrication of more advanced bio-recognition layers for bio-affinity sensors using a printing technology that is compatible with flexible and cheap paper substrates. This article is part of a Special Issue entitled Organic Bioelectronics - Novel Applications in Biomedicine.

Biocomposites of nanofibrillated cellulose, polypyrrole, and silver nanoparticles with electroconductive and antimicrobial properties.

In this work, flexible and free-standing composite films of nanofibrillated cellulose/polypyrrole (NFC/PPy) and NFC/PPy-silver nanoparticles (NFC/PPy-Ag) have been synthesized for the first time via in situ one-step chemical polymerization and applied in potential biomedical applications. Incorporation of NFC into PPy significantly improved its film formation ability resulting in composite materials with good mechanical and electrical properties. It is shown that the NFC/PPy-Ag composite films have strong inhibition effect against the growth of Gram-positive bacteria, e.g., Staphylococcus aureus. The electrical conductivity and strong antimicrobial activity makes it possible to use the silver composites in various applications aimed at biomedical treatments and diagnostics. Additionally, we report here the structural and morphological characterization of the composite materials with Fourier-transform infrared spectroscopy, atomic force microscopy, and scanning and transmission electron microscopy techniques.

An impedimetric study of DNA hybridization on paper-supported inkjet-printed gold electrodes.

In this study, two different supramolecular recognition architectures for impedimetric detection of DNA hybridization have been formed on disposable paper-supported inkjet-printed gold electrodes. The gold electrodes were fabricated using a gold nanoparticle based ink. The first recognition architecture consists of subsequent layers of biotinylated self-assembly monolayer (SAM), streptavidin and biotinylated DNA probe. The other recognition architecture is constructed by immobilization of thiol-functionalized DNA probe (HS-DNA) and subsequent backfill with 11-mercapto-1-undecanol (MUOH) SAM. The binding capacity and selectivity of the recognition architectures were examined by surface plasmon resonance (SPR) measurements. SPR results showed that the HS-DNA/MUOH system had a higher binding capacity for the complementary DNA target. Electrochemical impedance spectroscopy (EIS) measurements showed that the hybridization can be detected with impedimetric spectroscopy in picomol range for both systems. EIS signal indicated a good selectivity for both recognition architectures, whereas SPR showed very high unspecific binding for the HS-DNA/MUOH system. The factors affecting the impedance signal were interpreted in terms of the complexity of the supramolecular architecture. The more complex architecture acts as a less ideal capacitive sensor and the impedance signal is dominated by the resistive elements.

Polynorepinephrine and polydopamine-bacterial laccase coatings for phenolic amperometric biosensors.

The successful fabrication of biosensors is greatly limited by the immobilization of their bioreceptor, thus we propose a facile and reproducible two-step method to modify graphite electrodes with a bacterial laccase, relying on a fast and controllable potentiostatic process to coat graphite surfaces with biomolecule-compatible thin films of polynorepinephrine (ePNE) and polydopamine (ePDA). Both polymers, synthesized with a similar thickness, were functionalized with bacterial laccase, displaying distinct electrochemical transducing behaviours at pH 5.0 and 7.0. ePNE layer enables adequate electron transfer of anionic and cationic species in acidic and neutral media, whereas transduction across ePDA strongly depends on pH and redox probe charge. ePNE stands out by improving the amperometric responses of the biosensing interface towards a phenolic acid (gallic acid) and a flavonoid (catechin), in respect to ePDA. The optimal graphite/ePNE/laccase interface outperforms biosensing interfaces based on fungal laccases at neutral pH, displaying detection sensitivities of 104 and 14.4 µA cm-2 mM-1for gallic acid and catechin, respectively. The fine synthetic control of the ePNE bio-inspired transduction layer and the use of an alkaliphilic bacterial laccase enabled the construction of an amperometric biosensing interface with extended pH range of polyphenols detection present in food products and agro-industrial waste.

Low-cost reduced graphene oxide-based conductometric nitrogen dioxide-sensitive sensor on paper.

The fabrication concept for a low-cost sensor device using reduced graphene oxide (rGO) as the sensing material on a porous paper substrate is presented. The sensors were characterized using conductivity and capacitance measurements, atomic force microscopy and X-ray photoelectron spectroscopy. The effects of different reducing agents, graphene oxide (GO) flake size and film thickness were studied. The sensor was sensitive to NO2, and devices based on a thin (10-nm) hydrazine-reduced GO layer had the best sensitivity, reaching a 70% reduction in resistance after 10 min of exposure to 10 ppm NO2. The sensitivity was high enough for the detection of sub-parts per million levels of NO2. Desorption of gas molecules, i.e. the recovery of the sensor, could be accelerated by UV irradiation. The structure and preparation of the sensor are simple and up-scalable, allowing their fabrication in bulk quantities, and the fabrication concept can be applied to other materials, too.

Depolymerisation of Kraft Lignin by Tailor-Made Alkaliphilic Fungal Laccases.

Lignins released in the black liquors of kraft pulp mills are an underutilised source of aromatics. Due to their phenol oxidase activity, laccases from ligninolytic fungi are suitable biocatalysts to depolymerise kraft lignins, which are characterised by their elevated phenolic content. However, the alkaline conditions necessary to solubilise kraft lignins make it difficult to use fungal laccases whose activity is inherently acidic. We recently developed through enzyme-directed evolution high-redox potential laccases active and stable at pH 10. Here, the ability of these tailor-made alkaliphilic fungal laccases to oxidise, demethylate, and depolymerise eucalyptus kraft lignin at pH 10 is evidenced by the increment in the content of phenolic hydroxyl and carbonyl groups, the methanol released, and the appearance of lower molecular weight moieties after laccase treatment. Nonetheless, in a second assay carried out with higher enzyme and lignin concentrations, these changes were accompanied by a strong increase in the molecular weight and content of ß-O-4 and ß-5 linkages of the main lignin fraction, indicating that repolymerisation of the oxidised products prevails in one-pot reactions. To prevent it, we finally conducted the enzymatic reaction in a bench-scale reactor coupled to a membrane separation system and were able to prove the depolymerisation of kraft lignin by high-redox alkaliphilic laccase.

Tailor-made alkaliphilic and thermostable fungal laccases for industrial wood processing.

BACKGROUND: During the kraft process to obtain cellulosic pulp from wood, most of the lignin is removed by high-temperature alkaline cooking, released in the black liquors and usually incinerated for energy. However, kraft lignins are a valuable source of phenolic compounds that can be valorized in new bio-based products. The aim of this work is to develop laccases capable of working under the extreme conditions of high temperature and pH, typical of the industrial conversion of wood into kraft pulp and fibreboard, in order to provide extremophilic biocatalysts for depolymerising kraft lignin, and enzyme-assisted technologies for kraft pulp and fibreboard production. RESULTS: Through systematic enzyme engineering, combining enzyme-directed evolution and rational design, we changed the optimal pH of the laccase for oxidation of lignin phenols from acidic to basic, enhanced the catalytic activity at alkaline pH and increased the thermal tolerance of the enzyme by accumulating up to eight mutations in the protein sequence. The extremophilic laccase variants show maximum activity at 70 °C and oxidize kraft lignin at pH 10. Their integration into industrial-type processes saves energy and chemicals. As a pre-bleaching stage, the enzymes promote kraft pulp bleachability and significantly reduce the need for chlorine dioxide compared to the industrial sequence. Their application in wood chips during fibreboard production, facilitates the defibering stage, with less energy required. CONCLUSIONS: A set of new alkaliphilic and thermophilic fungal laccases has been developed to operate under the extreme conditions of high temperature and pH typical of industrial wood conversion processes. For the first time basidiomycete laccases of high-redox potential show activity on lignin-derived phenols and polymeric lignin at pH 10. Considering the extreme conditions of current industrial processes for kraft pulp and fibreboard production, the new tailor-made laccases constitute a step forward towards turning kraft pulp mills into biorefineries. Their use as biocatalysts in the wood conversion sector is expected to support the development of more environmentally sound and efficient processes, and more sustainable products.

Langmuir-Schaeffer films from a pi-pi stacking perylenediimide dye: organization and charge transfer properties.

The organization of pi-pi stacking perylenediimide (PDI) derivative, PDI12, was studied in solution and in thin films. Films were prepared with the Langmuir-Schaeffer (LS) method and characterized by means of AFM, optical profilometry, steady-state absorption, emission, fluorescence lifetime, and transient photovoltage measurements. The columnar aggregates observed previously in PDI12 solutions and in spin-coated films persist also in LS films. Because of the specific conditions during the preparation of the LS film, i.e., hydrophobic interactions and lateral compression, the columnar aggregates seem to organize with their long axis perpendicular to the layer plane whereas in spin-coated films the columns were oriented parallel to the layer plane. According to AFM and profilometer results, the thickness of LS monolayer of PDI12 is 10 nm, indicating that it consists mainly of aggregates, each containing approximately 30 monomers. Intermolecular photoinduced energy and electron transfer processes in C(60)|PDI12 double layer junction were studied. The fluorescence lifetime of PDI12 film is exceptionally long, but the quenching is very efficient in the presence of C(60). In charge transfer studies, long-lived photovoltage signal was observed for the double layer. Results of this work indicate that PDI12 acts as an electron acceptor and fullerene C(60) as an electron donor.

Photoinduced electron transfer in thin films of porphyrin-fullerene dyad and perylenetetracarboxidiimide.

Photoinduced intra- and intermolecular electron transfer (ET) in thin films of porphyrin-fullerene dyad (P-F) and perylenetetracarboxidiimide (PTCDI) was studied by means of photoelectrical and spectroscopic methods. Films consisting of smooth 100 mol% layers of P-F and PTCDI were prepared by the Langmuir-Schäfer (LS) technique and thermal evaporation, respectively. The time-resolved Maxwell displacement charge (TRMDC) and laser flash-photolysis methods were utilized to demonstrate photoinduced ET from P-F to PTCDI regardless of which chromophore is photoexcited. Finally, the information about the electron movement in the respective thin films was used to build a layered organic solar cell, whose internal quantum yield (Φ(I)) of collected charges was 13%.

Human dermal fibroblast proliferation controlled by surface roughness of two-component nanostructured latex polymer coatings.

In this study hierarchically-structured latex polymer coatings and self-supporting films were characterised and their suitability for cell growth studies was tested with Human Dermal Fibroblasts (HDF). Latex can be coated or printed on rigid or flexible substrates thus enabling high-throughput fabrication. Here, coverslip glass substrates were coated with blends of two different aqueous latex dispersions: hydrophobic polystyrene (PS) and hydrophilic carboxylated acrylonitrile butadiene styrene (ABS). The nanostructured morphology and topography of the latex films was controlled by varying the mixing ratio of the components in the latex blend. Thin latex-coatings retain high transparency on glass allowing optical and high resolution imaging of cell growth and morphology. Compared to coverslip glass surfaces and commercial well-plates HDF cell growth was enhanced up to 150-250 % on latex surfaces with specific nanostructure. Growth rates were correlated with selected roughness parameters such as effective surface area (Sq), RMS-roughness (Sdr) and correlation length (Scl37). High-resolution confocal microscopy clearly indicated less actin stress-fibre development in cells on the latex surface compared to coverslip glass. The results show that surface nanotopography can, by itself, passively modulate HDF cell proliferation and cytoskeletal architecture.

Structural and Functional Dynamics of Staphylococcus aureus Biofilms and Biofilm Matrix Proteins on Different Clinical Materials.

Medical device-associated staphylococcal infections are a common and challenging problem. However, detailed knowledge of staphylococcal biofilm dynamics on clinically relevant surfaces is still limited. In the present study, biofilm formation of the Staphylococcus aureus ATCC 25923 strain was studied on clinically relevant materials-borosilicate glass, plexiglass, hydroxyapatite, titanium and polystyrene-at 18, 42 and 66 h. Materials with the highest surface roughness and porosity (hydroxyapatite and plexiglass) did not promote biofilm formation as efficiently as some other selected materials. Matrix-associated poly-N-acetyl-ß-(1-6)-glucosamine (PNAG) was considered important in young (18 h) biofilms, whereas proteins appeared to play a more important role at later stages of biofilm development. A total of 460 proteins were identified from biofilm matrices formed on the indicated materials and time points-from which, 66 proteins were proposed to form the core surfaceome. At 18 h, the appearance of several r-proteins and glycolytic adhesive moonlighters, possibly via an autolysin (AtlA)-mediated release, was demonstrated in all materials, whereas classical surface adhesins, resistance- and virulence-associated proteins displayed greater variation in their abundances depending on the used material. Hydroxyapatite-associated biofilms were more susceptible to antibiotics than biofilms formed on titanium, but no clear correlation between the tolerance and biofilm age was observed. Thus, other factors, possibly the adhesive moonlighters, could have contributed to the observed chemotolerant phenotype. In addition, a protein-dependent matrix network was observed to be already well-established at the 18 h time point. To the best of our knowledge, this is among the first studies shedding light into matrix-associated surfaceomes of S. aureus biofilms grown on different clinically relevant materials and at different time points.

Nonlinear optical and structural properties of langmuir-blodgett films of thiohelicenebisquinones.

We provide a detailed investigation of the second-order nonlinear optical and structural properties of Langmuir-Blodgett (LB) films of nonracemic thiohelicenebisquinone (THBQ). We prepare both X- and Y-type films of different thicknesses and characterize them using optical second-harmonic generation and atomic-force microscopy (AFM). We find that the overall nonlinear properties of the samples are essentially independent of the film thickness and the deposition type and arise from susceptibility tensor components associated with chirality. Both X- and Y-type films can be described by D2 symmetry, which is a higher symmetry than the previously assumed C2 of LB films of THBQ and a similar helicenebisquinone (HBQ). However, the two types of films are shown to differ significantly with respect to the orientation of the in-plane axis. For Y type, the axis follows the direction of vertical sample deposition, but for X type, the direction of the axis varies randomly and significantly between different samples. The Y-type samples are therefore more ordered than the X-type samples. This was confirmed by AFM measurements in which the Y type exhibits uniform ordering into columnar structures. Similar structures in X type, on the other hand, are shorter and more randomly oriented, like those earlier observed for racemic samples of HBQ [Verbiest, T., et al. Science 1998, 282, 913]. The common nonlinear properties and different high-level ordering observed here for two different types of nonracemic samples reinforces that the nonlinearity of THBQ (and probably HBQ, as well) originates from the low-level columnar aggregation of the molecules with the higher-level structures playing a lesser role. In addition, within the columns, the molecules likely assume fairly random azimuthal orientations so that the columns themselves exhibit approximate Dinfinity symmetry.

Enzymatic Processes to Unlock the Lignin Value.

Main hurdles of lignin valorization are its diverse chemical composition, recalcitrance, and poor solubility due to high-molecular weight and branched structure. Controlled fragmentation of lignin could lead to its use in higher value products such as binders, coatings, fillers, etc. Oxidative enzymes (i.e., laccases and peroxidases) have long been proposed as a potentially promising tool in lignin depolymerization. However, their application was limited to ambient pH, where lignin is poorly soluble in water. A Finnish biotechnology company, MetGen Oy, that designs and supplies industrial enzymes, has developed and brought to market several lignin oxidizing enzymes, including an extremely alkaline lignin oxidase MetZyme® LIGNO™, a genetically engineered laccase of bacterial origin. This enzyme can function at pH values as high as 10-11 and at elevated temperatures, addressing lignin at its soluble state. In this article, main characteristics of this enzyme as well as its action on bulk lignin coming from an industrial process are demonstrated. Lignin modification by MetZyme® LIGNO™ was characterized by size exclusion chromatography, UV spectroscopy, and dynamic light scattering for monitoring particle size of solubilized lignin. Under highly alkaline conditions, laccase treatment not only decreased molecular weight of lignin but also increased its solubility in water and altered its dispersion properties. Importantly, organic solvent-free soluble lignin fragmentation allowed for robust industrially relevant membrane separation technologies to be applicable for product fractionation. These enzyme-based solutions open new opportunities for biorefinery lignin valorization thus paving the way for economically viable biorefinery business.

Photothermal effect of gold nanostar patterns inkjet-printed on coated paper substrates with different permeability.

Inkjet printing of spherical gold nanoparticles is widely applied in the fabrication of analytical and diagnostics tools. These methods could be extended to non-spherical gold nanoparticles that can efficiently release heat locally when irradiated in the near infrared (NIR) wavelength region, due to localized surface plasmon resonance (LSPR). However, this promising application requires the ability to maintain high efficiency and tunability of the NIR LSPR of the printed nanoparticles. In this study stable inks containing PEGylated gold nanostars (GNS) were fabricated and successfully inkjet-printed onto differently coated paper substrates with different porosity and permeability. A pronounced photothermal effect was observed under NIR excitation of LSPR of the printed GNS patterns even at low laser intensities. It was found that beside the direct role of the laser intensity, this effect depends appreciably on the printing parameters, such as drop density (δ, drops/mm2) and number of printed layers, and, critically, on the permeability of the coated paper substrates. These results will promote the development of GNS-based printed platforms for local photothermal therapy.

Fabrication of Inkjet-Printed Gold Nanostar Patterns with Photothermal Properties on Paper Substrate.

Inkjet printing technology has brought significant advances in patterning various functional materials that can meet important challenges in personalized medical treatments. Indeed, patterning of photothermal active anisotropic gold nanoparticles is particularly promising for the development of low-cost tools for localized photothermal therapy. In the present work, stable inks containing PEGylated gold nanostars (GNSs) were prepared and inkjet printed on a pigment-coated paper substrate. A significant photothermal effect (ΔT ≅ 20 °C) of the printed patterns was observed under near infrared (NIR) excitation of the localized surface plasmon resonance (LSPR) of the GNS with low laser intensity (I ≅ 0.2 W/cm(2)). Besides the pronounced photothermal effect, we also demonstrated, as an additional valuable effect, the release of a model fluorescent thiol-terminated Bodipy dye (BDP-SH) from the printed gold surface, both under bulk heating and NIR irradiation. These preliminary results suggest the way of the development of a new class of low-cost, disposable, and smart devices for localized thermal treatments combined with temperature-triggered drug release.

Bioactive glass combined with bisphosphonates provides protection against biofilms formed by the periodontal pathogen Aggregatibacter actinomycetemcomitans.

Biofilms play a pivotal role in the progression of periodontitis and they can be treated with antiseptics (i.e. chlorhexidine) or antibiotics, but these therapeutic alternatives are unable of ameliorating periodontal alveolar bone loss, which has been, on the other hand, successfully treated with bone-preserving agents. The improved bone formation achieved in animal models by the combination of two such agents: bioactive glass (BAG) and bisphosphonates has attracted the interest for further exploring dental applications. However, the antimicrobial effects that may result from combining them have not been yet investigated. Here, our aim was to explore the anti-biofilm effects that could result from combining BAG with bisphosphonates, particularly in a dental biofilm model. The experiments were performed with an oral cavity single-specie (Aggregatibacter actinomycetemcomitans) biofilm assay, which was optimized in this contribution. Risedronate displayed an intrinsic anti-biofilm effect, and all bisphosphonates, except clodronate, reduced biofilm formation when combined with BAG. In particular, the anti-biofilm activity of risedronate was significantly increased by the combination with BAG. Since it has been proposed that some of the antimicrobial effects of BAG are caused by local pH changes, studies of pH variations were performed to gain a mechanistic understanding. However, the observed anti-biofilm effects could not be explained with lowered pHs. Overall, these results do provide further support for the promising use of bisphosphonate-BAG combinations in dental applications. These findings are particularly relevant for patients undergoing cancer chemotherapy, or osteoporotic patients, which are known to be more vulnerable to periodontitis. In such cases, bisphosphonate treatment could play a double positive effect: local treatment of periodontitis (in combination with BAG) and systemic treatment of osteoporosis, prevention of hypercalcemia and metastases.

Printing technologies for biomolecule and cell-based applications.

Biomolecules, such as enzymes, proteins and other biomacromolecules (polynucleotides, polypeptides, polysaccharides and DNA) that are immobilized on solid surfaces are relevant to many areas of science and technology. These functionalized surfaces have applications in biosensors, chromatography, diagnostic immunoassays, cell culturing, DNA microarrays and other analytical techniques. Printing technologies offer opportunities in this context. The main interests in printing biomolecules are in immobilizing them on surfaces for sensors and catalysts or for controlled delivery of protein-based drugs. Recently, there have been significant developments in the use of inkjet printing for dispensing of proteins, biomacromolecules and cells. This review discusses the use of roll-to-roll and inkjet printing technologies in manufacturing of biomolecule and cell-based applications.

Hyperspectral imaging in quality control of inkjet printed personalised dosage forms.

The aim of the study was to investigate applicability of near infra-red (NIR) hyperspectral imaging technique in quality control of printed personalised dosage forms. Inkjet printing technology was utilized to fabricate escalating doses of an active pharmaceutical ingredient (API). A solution containing anhydrous theophylline as the model drug was developed as a printable formulation. Single units solid dosage forms (SDFs) were prepared by jetting the solution onto 1 cm × 1 cm areas on carrier substrate with multiple printing passes. It was found that the number of printing passes was in excellent correlation (R(2)=0.9994) with the amount of the dispensed drug (µg cm(-2)) based on the UV calibration plot. The API dose escalation was approximately 7.5 µg cm(-2) for each printing pass concluding that inkjet printing technology can optimally provide solutions to accurate deposition of active substances with a potential for personalized dosing. Principal component analysis (PCA) was carried out in order to visualize the trends in the hyperspectral data. Subsequently, a quantitative partial least squares (PLS) regression model was created. NIR hyperspectral imaging proved (R(2)=0.9767) to be a reliable, rapid and non-destructive method to optimize quality control of these planar printed dosage forms.

Protein and bacterial interactions with nanostructured polymer coatings.

Adsorption of proteins and adhesion of bacteria to a surface is affected by chemical and physical interactions. In this study, polymer coatings and their ability to adsorb avidin and Staphylococcus aureus were investigated. The surface chemistry and topography of the polymer coatings was modified by changing the weight ratio of the hydrophobic polystyrene (PS) and the hydrophilic acrylonitrile butadiene styrene (ABS) components in the polymer blend. Avidin adsorbed less to the ABS phase compared with the PS phase. The side-on orientation of avidin on the ABS surface, however, resulted in a higher specific binding of biotinylated bovine serum albumin. Steric effects and hydrophobic protein-surface interactions decreased the activity of avidin on the PS phase. The increased hydrophobicity and roughness of the polymer coatings enhanced the adhesion of S. aureus. The avidin-coated latex surface with 55% relative surface coverage of the PS phase showed anti-microbial behavior.