Flashing in-curb LEDs and beacons at unsignalized crosswalks and driver's visual attention to pedestrians during nighttime.

Driver's visual attention (eye movements) and driving behaviour (kinematic data) were assessed when approaching an experimental crosswalk that included flashing white in-curb LED strips, flashing orange beacons, backlit 'Yield here to pedestrians' vertical signs, and enhanced lighting when a staged pedestrian attempted to cross. An experimental condition in which all devices were active was compared with a control condition in which only enhanced lighting and backlit vertical signs were active. The results showed a significant increase of motorists' yielding compliance, distance of first fixation to the pedestrian area, standard deviation for horizontal eye movements in the experimental condition. The introduction of flashing in-curb LED strips and flashing orange beacons proved to be very effective in increasing the night-time safety of the pedestrian crossing. Practitioner summary: The study investigated the effects of flashing in-curb LED strips and beacons on driver's visual attention (eye movements) and speed when approaching a crosswalk during night-time. The results showed that the combination of these flashing devices significantly increased yielding compliance and the distance of pedestrian detection. Abbreviations: ANOVA: analysis of variance; EU: European Union; HAWK: high intensity activated crosswalk system; LED: light-emitting diode; PHB: pedestrian hybrid beacons; ROI: region of interest; RRFB: rectangular rapid flashing beacons; UK: United Kingdom; US: United States.

The role of peripheral vision in vertical road sign identification and discrimination.

The role of peripheral vision in road sign identification and discrimination was investigated in two studies. Peripheral vision plays an important role in road signs perception due to their lateral positioning. In the first study 20 participants identified road signs presented at five levels of horizontal eccentricity (1.1°-12.4°), and two levels of vertical eccentricity (0°-2.5°). In the second study road sign discrimination was tested in a same-different discrimination task. The first study showed that a vertical offset of 2.5° degraded proportion correct rate by 9%. Proportion correct rate decreased from 79% to 41% in the transition from 1.1° to 12.4° of horizontal offset. The second study showed an accurate discrimination for road signs presented within a horizontal offset of 6.4°. Road signs with angular shapes and prominent vertexes as triangular or cross signs were better identified in peripheral vision than signs with more compact shapes (circular signs). Practitioner summary: Vertical road signs, due to their lateral positioning, are often perceived in peripheral vision. Horizontal and vertical eccentricity negatively impacts the driver's ability to correctly identify and discriminate traffic signs. The use of singular shapes and a design with simple pictograms and large contrasting areas strongly facilitate road sign perception in peripheral vision.

Reflective Tape Applied to Bicycle Frame and Conspicuity Enhancement at Night.

OBJECTIVE: Four studies were conducted to assess bicyclist conspicuity enhancement at night by the application of reflective tape (ECE/ONU 104) to the bicycle rear frame and to pedal cranks. BACKGROUND: Previous studies have tested the benefits of reflective markings applied to bicyclist clothing. Reflective jackets however need to be available and worn while reflective markings enhance conspicuity without any active behavior by the bicyclist. METHOD: In the first study, reflective tape was applied to the rear frame. Detection distance was compared in four conditions: control, rear red reflector, high visibility jacket, and reflective tape. In the second study, the same conditions were studied with night street lighting on and off. In the third study, detection and recognition distances were evaluated in rainy conditions. In the fourth study, visibility was assessed with the reflective tape applied to pedal cranks. RESULTS: In the first study, the application of reflective markings resulted in a detection distance of 168.28 m. In the second study, the detection distance with reflective markings was 229.74 m with public street light on and 256.41 m with public street light off. In rainy conditions, detection distance using the reflective markings was 146.47 m. Reflective tape applied to pedal cracks resulted in a detection distance of 168.60 m. CONCLUSION: Reflective tape applied to the rear bicycle frame can considerably increase bicyclist conspicuity and safety at night. APPLICATION: Reflective tape is highly recommended to complement anterior and rear lights in bicycle riding at night.

Comparative Life Cycle Assessment (LCA) of Porous Asphalt Mixtures with Sustainable and Recycled Materials: A Cradle-to-Gate Approach.

The road and construction sectors consume a large number of natural resources and energy, contributing significantly to waste generation and greenhouse gas emissions (GHG). The use of recycled aggregate from construction and demolition waste as a substitute for virgin aggregate is a current practice in the construction of new road sections. Additionally, in recent years, there has been an increasing focus on finding alternatives to bitumen for binders used in asphalt mixes. This study investigates and compares the impacts associated with two porous asphalt mixtures produced with CDW aggregates, virgin aggregates, and a polyolefin-based synthetic transparent binder through an LCA methodology. A cradle-to-gate approach was employed. Model characterization for calculating the potential environmental impacts of each porous asphalt mixture was performed using the ReCipe 2016 assessment method at the midpoint and endpoint levels. The results are presented with reference to a baseline scenario corresponding to a porous asphalt mixture, confirming the benefits associated with the use of recycled aggregates and in some cases the benefits of not using bitumen-based binders. This work contributes to the understanding of the importance of choosing the least environmentally damaging solution during the production or rehabilitation of road pavement infrastructure.

Laser scanning on road pavements: a new approach for characterizing surface texture.

The surface layer of road pavement has a particular importance in relation to the satisfaction of the primary demands of locomotion, such as security and eco-compatibility. Among those pavement surface characteristics, the "texture" appears to be one of the most interesting with regard to the attainment of skid resistance. Specifications and regulations, providing a wide range of functional indicators, act as guidelines to satisfy the performance requirements. This paper describes an experiment on the use of laser scanner techniques on various types of asphalt for texture characterization. The use of high precision laser scanners, such as the triangulation types, is proposed to expand the analysis of road pavement from the commonly and currently used two-dimensional method to a three-dimensional one, with the aim of extending the range of the most important parameters for these kinds of applications. Laser scanners can be used in an innovative way to obtain information on areal surface layer through a single measurement, with data homogeneity and representativeness. The described experience highlights how the laser scanner is used for both laboratory experiments and tests in situ, with a particular attention paid to factors that could potentially affect the survey.

Mechanical Characterization of Thin Asphalt Overlay Mixtures with 100% Recycled Aggregates.

Asphalt pavements inevitably deteriorate over time, requiring frequent maintenance work to ensure the proper serviceability of the road network. Small interventions, such as resurfacing for pavement preservation, are preferable to reconstruction at the end of roads' in-service lives as they limit environmental- and economic-related impacts. Thin asphalt overlay (TAO) mixture represents a suitable maintenance solution to restore the functional properties of road surfaces. Due to the increasing awareness of the depletion of non-renewable resources and the importance of promoting the circular economy, this study evaluated the possibility of using fully recycled TAO mixes by investigating their volumetric and mechanical properties. Two eco-friendly TAO mixes were designed using recycled aggregates from reclaimed asphalt pavements, a municipal solid waste incinerator, and steel slags in order to meet EN 13108-2 requirements. The TAO mixes differed in regard to the type of bituminous binder (neat/SBS-modified bitumens) and fibres (natural/synthetic) employed. The preliminary results demonstrated that the presence of recycled aggregates did not negatively affect the workability and the mechanical performances of the two sustainable mixtures in terms of stiffness, tensile resistance, rutting and moisture susceptibility. Of these, the TAO mix with neat bitumen and synthetic fibres showed enhanced mechanical performance highlighting the structural effects of the used fibres.

New Micromobility Means of Transport: An Analysis of E-Scooter Users' Behaviour in Trondheim.

Negative effects of a massive use of cars, such as congestion, air pollution, noise, and traffic injuries, are affecting the cities everywhere. Recently introduced shared vehicles, such as e-scooters and electric bicycles, could potentially accelerate the transition towards sustainable mobility. Although these vehicles are becoming increasingly common and accepted within regulatory frameworks, some local governments are not yet ready to integrate e-scooters into their transport systems. Indeed, the legislation is unclear as it is not easy to determine whether the e-scooter is more like a bicycle or a vehicle. Moreover, it is difficult to predict the impact of e-scooters on road traffic, as well as the type of road infrastructure chosen by e-scooter drivers or the possible interaction of such vehicles with weak road users, such as pedestrians or cyclists. This study showed an analysis of speed and behaviour of e-scooter drivers in the city of Trondheim (Norway) to investigate how to manage this mode of transport. A total of 204 e-scooters were observed on six different roads in the city centre. The speed of e-scooter drivers was measured by a speed tracker (average value 15.4 km/h) and their behaviour recorded by a hidden observer in the field. Gender, age, distance from pedestrians, speed adaptation to the environment, and type of vehicle used were registered for each e-scooter. Through a Binomial Logit analysis, the data obtained were used to analyse the type of road infrastructure preferred by e-scooter drivers. Results showed that the cycle path is more widely used with percentage value from 60% to 90% of users. In addition, the probability of choice depended mainly on the road environment. The aim of this analysis was to assist local authorities in regulating the safe use of e-scooters and developing appropriate policies for their integration into cities.

Use of Steel Slag as an Alternative to Aggregate and Filler in Road Pavements.

Today the use of Construction and Demolition Materials (CDM) can be considered as a suitable solution for the construction or the rehabilitation of road pavements. In this context, it is central to minimizing waste production, favoring the reuse through new production cycles to replace virgin natural raw materials. As illustrated in this study, steel slag has mechanical properties that justify its use as aggregate in the manufacture of bituminous mixes. In road construction, their use is focused on the substitution of fine aggregate and filler in bituminous mixtures. Mechanical characterizations, Marshall stability and indirect tensile resilient modulus (ITSM) tests were used to evaluate the laboratory performance of the mixtures. The research aims are to provide the use of these materials for the construction of the entire road pavement structure; in this study authors used these materials both in the characterization of cementitious layers and in those with bituminous conglomerate. In both cases, the use of steel slag has favored an increase of stiffness in the mixtures.

Driver's visual attention to different categories of roadside advertising signs.

Roadside advertising signs are a salient potential source of driver's distraction. Previous research has mainly investigated driver's visual attention to billboards, which represents only one category of advertising signs. In this study, driver's visual attention was assessed in a naturalistic driving setting for six categories of roadside advertising signs: vendor signs, billboards, movable display boards, single and multiple commercial directional signs, and gas price LED displays. Fixation rate, fixation duration, fixation distance and driving speed were assessed in a sample of 15 drivers along a 30-km route including a total of 154 advertising signs belonging to the six categories described above. The role of clearance from the road, elevation, height, width, surface, number and size of characters, total number of characters, side of the road (driving side, opposite side), context (rural, urban), were also considered. Overall 24% of the roadside advertising signs were fixated. Fixation rate was significantly influenced by sign category, clearance from the road and number of characters. Median value for fixation duration was 297 ms. Fixation duration was significantly influenced by speed, elevation from road level, number of medium size characters, and was higher in the rural context. Median value for fixation distance was 58.10 m, and was significantly influenced by advertising sign category, character count and speed.

Mechanical and Thermal Performance of Macro-Encapsulated Phase Change Materials for Pavement Application.

Macro-encapsulated phase change material (PCM) lightweight aggregates (ME-LWA) were produced and evaluated for their mechanical and thermal properties in road engineering applications. The ME-LWAs were first characterised in terms of their physical and geometrical properties. Then, the ME-LWAs were investigated in detail by applying the European Standards of testing for the Bulk Crushing Test and the Polished Stone Value (PSV) coefficient as well as Micro-Deval and laboratory profilometry. In addition, the thermal performance for possible construction of smart pavements with the inclusion of ME-LWAs for anti-ice purposes was determined. The crushing resistance of the ME-LWAs was improved, while their resistance to polishing was reduced. Thermal analysis of the encapsulated PCM determined it to possess excellent thermal stability and a heat storage capacity of 30.43 J/g. Based on the research findings, the inclusion of ME-LWAs in surface pavement layers could be considered a viable solution for the control of surface temperatures in cold climates. Road safety and maintenance could benefit in terms of reduced ice periods and reduced treatments with salts and other anti-ice solutions.

Fixation distance and fixation duration to vertical road signs.

The distance of first-fixation to vertical road signs was assessed in 22 participants while driving a route of 8.34 km. Fixations to road signs were recorded by a mobile eye-movement-tracking device synchronized to GPS and kinematic data. The route included 75 road signs. First-fixation distance and fixation duration distributions were positively skewed. Median distance of first-fixation was 51 m. Median fixation duration was 137 ms with a modal value of 66 ms. First-fixation distance was linearly related to speed and fixation duration. Road signs were gazed at a much closer distance than their visibility distance. In a second study a staircase procedure was used to test the presentation-time threshold that lead to a 75% accuracy in road sign identification. The threshold was 35 ms, showing that short fixations to a road signs could lead to a correct identification.

EEG-Based Mental Workload Neurometric to Evaluate the Impact of Different Traffic and Road Conditions in Real Driving Settings.

Car driving is considered a very complex activity, consisting of different concomitant tasks and subtasks, thus it is crucial to understand the impact of different factors, such as road complexity, traffic, dashboard devices, and external events on the driver's behavior and performance. For this reason, in particular situations the cognitive demand experienced by the driver could be very high, inducing an excessive experienced mental workload and consequently an increasing of error commission probability. In this regard, it has been demonstrated that human error is the main cause of the 57% of road accidents and a contributing factor in most of them. In this study, 20 young subjects have been involved in a real driving experiment, performed under different traffic conditions (rush hour and not) and along different road types (main and secondary streets). Moreover, during the driving tasks different specific events, in particular a pedestrian crossing the road and a car entering the traffic flow just ahead of the experimental subject, have been acted. A Workload Index based on the Electroencephalographic (EEG), i.e., brain activity, of the drivers has been employed to investigate the impact of the different factors on the driver's workload. Eye-Tracking (ET) technology and subjective measures have also been employed in order to have a comprehensive overview of the driver's perceived workload and to investigate the different insights obtainable from the employed methodologies. The employment of such EEG-based Workload index confirmed the significant impact of both traffic and road types on the drivers' behavior (increasing their workload), with the advantage of being under real settings. Also, it allowed to highlight the increased workload related to external events while driving, in particular with a significant effect during those situations when the traffic was low. Finally, the comparison between methodologies revealed the higher sensitivity of neurophysiological measures with respect to ET and subjective ones. In conclusion, such an EEG-based Workload index would allow to assess objectively the mental workload experienced by the driver, standing out as a powerful tool for research aimed to investigate drivers' behavior and providing additional and complementary insights with respect to traditional methodologies employed within road safety research.

Incorporation of Rubber Powder as Filler in a New Dry-Hybrid Technology: Rheological and 3D DEM Mastic Performances Evaluation.

In recent years, the use of crumb rubber as modifier or additive within asphalt concretes has allowed obtaining mixtures able to bind high performances to recovery and reuse of discarded tires. To date, the common technologies that permit the reuse of rubber powder are the wet and dry ones. In this paper, a dry-hybrid technology for the production of Stone Mastic Asphalt mixtures is proposed. It allows the use of the rubber powder as filler, replacing part of the limestone one. Fillers are added and mixed with a high workability bitumen, modified with SBS (styrene-butadiene-styrene) polymer and paraffinic wax. The role of rubber powder and limestone filler within the bituminous mastic has been investigated through two different approaches. The first one is a rheological approach, which comprises a macro-scale laboratory analysis and a micro-scale DEM simulation. The second, instead, is a performance approach at high temperatures, which includes Multiple Stress Creep Recovery tests. The obtained results show that the rubber works as filler and it improves rheological characteristics of the polymer modified bitumen. In particular, it increases stiffness and elasticity at high temperatures and it reduces complex modulus at low temperatures.