NC-AFM observation of atomic scale structure of rutile-type TiO2(110) surface prepared by wet chemical process.

We succeeded in observing the atomic scale structure of a rutile-type TiO2(110) single-crystal surface prepared by the wet chemical method of chemical etching in an acid solution and surface annealing in air. Ultrahigh vacuum noncontact atomic force microscopy (UHV-NC-AFM) was used for observing the atomic scale structures of the surface. The UHV-NC-AFM measurements at 450 K, which is above a desorption temperature of molecularly adsorbed water on the TiO2(110) surface, enabled us to observe the atomic scale structure of the TiO2(110) surface prepared by the wet chemical method. In the UHV-NC-AFM measurements at room temperature (RT), however, the atomic scale structure of the TiO2(110) surface was not observed. The TiO2(110) surface may be covered with molecularly adsorbed water after the surface was prepared by the wet chemical method. The structure of the TiO2(110) surface that was prepared by the wet chemical method was consistent with the (1 x 1) bulk-terminated model of the TiO2(110) surface.

Chain structures of surface hydroxyl groups formed via line oxygen vacancies on TiO2(110) surfaces studied using noncontact atomic force microscopy.

Structures of surface hydroxyl groups arranged on a reduced TiO2(110) surface that had line oxygen vacancies were studied using noncontact atomic force microscopy (NC-AFM). NC-AFM results revealed that by increasing the density of oxygen vacancies on the TiO2(110) surface, line oxygen vacancies were formed by removal of oxygen atoms in a bridge oxygen row on the TiO2(110) surface. After the TiO2(110) surface with the line oxygen vacancies was exposed to water, the surface showed hydroxyl chain structures that were composed of hydroxyl groups linearly arranged in a form of two rows on the line oxygen vacancies and on a neighboring bridge oxygen row. In-situ NC-AFM measurements of these surfaces exposed to water at room temperature revealed that hydroxyl chain structures were formed at the line oxygen vacancy. Annealing above 500 K was sufficient to remove the hydroxyl chain structures on the TiO2(110) surface and allowed line oxygen vacancies to reappear on the surface. The line oxygen vacancies are active sites for water dissociation. In conclusion, the formation of the hydroxyl chain structure suggests that the surface hydroxyl groups on a TiO2(110) surface can be controlled by preparing oxygen vacancy structures on the surface.

Oxygen vacancy promoting catalytic dehydration of formic acid on TiO2(110) by in situ scanning tunneling microscopic observation.

The catalytic dehydration reaction processes of formic acid on a TiO2(110) surface at 350 K have been studied to visualize reaction intermediates and their dynamic behaviors by scanning tunneling microscopy. Three types of configurations of adsorbed formates on the surface were identified by their shapes and positions in STM images. Successive STM observations revealed transformations among the three configurations, i.e., bridge formate on a 5-fold coordinated Ti4+ row, bridge formate on an oxygen vacancy site with an oxygen atom of formate and on a 5-fold coordinated Ti4+ ion and with the other formate oxygen atom, and a monodentate formate on an oxygen vacancy site with an oxygen atom of formate. The decomposition of the monodentate formate to carbon monoxide and hydroxyl was also imaged, which is a rate-determining step in the catalytic dehydration of formic acid. Combined with first-principle DFT calculations, the overall reaction processes of the catalytic dehydration of formic acid on the surface have been elucidated. Oxygen vacancies on the surface that can be produced by dehydration of two hydroxyls in situ under the catalytic reaction conditions are essential for the reaction.

Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS): comparison of different internal standardization methods using laser-induced plasma (LIP) emission and LA-ICP-MS signals.

The source of signal variations that governs the analytical performance of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was investigated in this study. In order to specify the source of signal variations of LA-ICP-MS, laser-induced plasma (LIP) Fe emission, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals were used as internal standards for the determination of trace elements in low-alloy steel certified reference materials (BS 50D and JSS 1005-1008). Fe 1373.5 nm emission signals from LIP were measured, while trace element LA-ICP-MS signals were collected. After that, the LIP emission signals, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals were used as internal standards, and the analytical performance was evaluated by the RSDs and the correlation coefficients (r) of the calibration curves. The improvement factors were dependent on the internal standardization methods. Analytical precisions (RSDs) of trace element LA-ICP-MS signals were improved by factors of 1.5-3.3 using LIP Fe emission signals as an internal standard. The improvement factors of 2.5 - 5.9 and 4.1 - 17 were obtained by using LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals as internal standards, respectively. Better correlation coefficients (r) were also obtained using the LA-ICP-MS signal compensation (0.9985 by LA-ICP-MS Fe+ and 0.9996 by LA-ICP-MS Ni+) rather than the LIP Fe emission compensation (0.9932). In this paper we compare and discuss the analytical performance achieved by LA-ICP-MS using LIP Fe emission, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals as internal standards.