RESUMEN
This paper describes a compact electronic system employing a synchronous demodulation measurement method for the acquisition of pulsed-current signals. The fabricated prototype shows superior performance in terms of signal-to-noise ratio in comparison to conventional instrumentation performing free-running measurements, especially when extremely narrow pulses are concerned. It shows a reading error around 0.1% independently of the signal duty cycle (D) in the investigated D = 10−4−10−3 range. Conversely, high-precision electrometers display reading errors as high as 30% for a D = 10−4, which reduces to less than 1% only for D > 3 × 10−3. Field tests demonstrate that the developed front-end/readout electronics is particularly effective when coupled to dosimeters irradiated with the X-rays sourced by a medical linear accelerator. Therefore, it may surely be exploited for the real-time monitoring of the dosimeter output current, as required in modern radiotherapy techniques employing ultra-narrow pulses of high-energy photons or nuclear particles.
Asunto(s)
Electrónica , Fotones , Radiometría , Relación Señal-Ruido , Rayos XRESUMEN
Highly accurate and stable current references are especially required for resistive-sensor conditioning. The solutions typically adopted in using resistors and op-amps/transistors display performance mainly limited by resistors accuracy and active components non-linearities. In this work, excellent characteristics of LT199x selectable gain amplifiers are exploited to precisely divide an input current. Supplied with a 100 µA reference IC, the divider is able to exactly source either a ~1 µA or a ~0.1 µA current. Moreover, the proposed solution allows to generate a different value for the output current by modifying only some connections without requiring the use of additional components. Experimental results show that the compliance voltage of the generator is close to the power supply limits, with an equivalent output resistance of about 100 GΩ, while the thermal coefficient is less than 10 ppm/°C between 10 and 40 °C. Circuit architecture also guarantees physical separation of current carrying electrodes from voltage sensing ones, thus simplifying front-end sensor-interface circuitry. Emulating a resistive-sensor in the 10 kΩ-100 MΩ range, an excellent linearity is found with a relative error within ±0.1% after a preliminary calibration procedure. Further advantage is that compliance voltage can be opposite in sign of that obtained with a passive component; therefore, the system is also suitable for conditioning active sensors.
RESUMEN
Accurate dosimetry of ultra-high dose-rate beams using diamond detectors remains challenging, primarily due to the elevated photocurrent peaks exceeding the input dynamics of precision electrometers. This work aimed at demonstrating the effectiveness of compact gated-integration electronics in conditioning the current peaks (>20 mA) generated by a highly sensitive (S ≃ 26 nC/Gy) custom-made diamond photoconductor under electron FLASH irradiation, as well as in real-time monitoring of beam dose and dose-rate. For the emerging FLASH technology, this study provided a new perspective on using commercially available diamond dosimeters with high sensitivity, currently employed in conventional radiotherapy.
RESUMEN
Metal-halide perovskites are revolutionizing the world of X-ray detectors, due to the development of sensitive, fast, and cost-effective devices. Self-powered operation, ensuring portability and low power consumption, has also been recently demonstrated in both bulk materials and thin films. However, the signal stability and repeatability under continuous X-ray exposure has only been tested up to a few hours, often reporting degradation of the detection performance. Here it is shown that self-powered direct X-ray detectors, fabricated starting from a FAPbBr3 submicrometer-thick film deposition onto a mesoporous TiO2 scaffold, can withstand a 26-day uninterrupted X-ray exposure with negligible signal loss, demonstrating ultra-high operational stability and excellent repeatability. No structural modification is observed after irradiation with a total ionizing dose of almost 200 Gy, revealing an unexpectedly high radiation hardness for a metal-halide perovskite thin film. In addition, trap-assisted photoconductive gain enabled the device to achieve a record bulk sensitivity of 7.28 C Gy-1 cm-3 at 0 V, an unprecedented value in the field of thin-film-based photoconductors and photodiodes for "hard" X-rays. Finally, prototypal validation under the X-ray beam produced by a medical linear accelerator for cancer treatment is also introduced.
RESUMEN
Nanostructured semiconductors have driven the research in electronic and optoelectronic devices in the new millennium era [...].
RESUMEN
Radiotherapy is now recognized as a pillar in the fight against cancer. Two different types are currently used in clinical practice: (1) external beam radiotherapy, using high-energy X-rays or electron beams, both in the MeV-range, and (2) intraoperative radiotherapy, using low-energy X-rays (up to 50 keV) and MeV-range electron beams. Versatile detectors able to measure the radiation dose independently from the radiation nature and energy are therefore extremely appealing to medical physicists. In this work, a dosimeter based on a high-quality single-crystal synthetic diamond sample was designed, fabricated and characterized under low-energy X-rays, as well as under high-energy pulsed X-rays and electron beams, demonstrating excellent linearity with radiation dose and dose-rate. Detector sensitivity was measured to be 0.299 ± 0.002 µC/Gy under 6 MeV X-ray photons, and 0.298 ± 0.004 µC/Gy under 6 MeV electrons, highlighting that the response of the diamond dosimeter is independent of the radiation nature. Moreover, in the case of low-energy X-rays, an extremely low limit of detection (23 nGy/s) was evaluated, pointing out the suitability of the device to radiation protection dosimetry.
RESUMEN
A recent innovation in diamond technology has been the development of the "black diamond" (BD), a material with very high optical absorption generated by processing the diamond surface with a femtosecond laser. In this work, we investigate the optical behavior of the BD samples to prove a near to zero dielectric permittivity in the high electric field condition, where the Frenkel-Poole (FP) effect takes place. Zero-epsilon materials (ENZ), which represent a singularity in optical materials, are expected to lead to remarkable developments in the fields of integrated photonic devices and optical interconnections. Such a result opens the route to the development of BD-based, novel, functional photonic devices.
RESUMEN
INTRODUCTION: Football was the first sport to resume competitions after the coronavirus disease 2019 (COVID-19) lockdown and promptly the hypothesis was raised of a potential relationship between the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection and musculoskeletal injuries in athletes. This study aimed to confirm the association between SARS-CoV-2 infection and muscle strain injury in a large population of elite football players and to investigate if the COVID-19 severity level could affect the risk of injury. METHODS: A retrospective cohort study involving 15 Italian professional male football teams was performed during the Italian Serie A 2020-2021 season. Injuries and SARS-CoV-2 positivity data were collected by team doctors through an online database. RESULTS: Of the 433 included players, we observed 173 SARS-CoV-2 infections and 332 indirect muscle strains. COVID-19 episodes mostly belonged to severity level I and II. The injury risk significantly increased after a COVID-19 event, by 36% (HR = 1.36, CI95% 1.05; 1.77, p-value = 0.02). The injury burden demonstrated an 86% increase (ratio = 1.86, CI95% 1.21; 2.86, p-value = 0.005) in the COVID-19 severity level II/III versus players without a previous SARS-CoV-2 infection, while level I (asymptomatic) patients showed a similar average burden (ratio = 0.92, CI95% 0.54; 1.58, p-value = 0.77). A significantly higher proportion of muscle-tendon junction injuries (40.6% vs. 27.1%, difference = 13.5%, CI95% 0.002%; 26.9%, p-value = 0.047) was found when comparing level II/III versus Non-COVID-19. CONCLUSIONS: This study confirms the correlation between SARS-CoV-2 infection and indirect muscle injuries and highlights how the severity of the infection would represent an additional risk factor.
Asunto(s)
Traumatismos en Atletas , COVID-19 , Fútbol Americano , Fútbol , Humanos , Masculino , Fútbol Americano/lesiones , Estudios Retrospectivos , Traumatismos en Atletas/epidemiología , COVID-19/epidemiología , SARS-CoV-2 , Control de Enfermedades Transmisibles , Fútbol/lesiones , Italia/epidemiología , Músculos/lesionesRESUMEN
Black diamond is an emerging material for solar applications. The femtosecond laser surface treatment of pristine transparent diamond allows the solar absorptance to be increased to values greater than 90% from semi-transparency conditions. In addition, the defects introduced by fs-laser treatment strongly increase the diamond surface electrical conductivity and a very-low activation energy is observed at room temperature. In this work, the investigation of electronic transport mechanisms of a fs-laser nanotextured diamond surface is reported. The charge transport was studied down to cryogenic temperatures, in the 30−300 K range. The samples show an activation energy of a few tens of meV in the highest temperature interval and for T < 50 K, the activation energy diminishes to a few meV. Moreover, thanks to fast cycles of measurement, we noticed that the black-diamond samples also seem to show a behavior close to ferromagnetic materials, suggesting electron spin influence over the transport properties. The mentioned properties open a new perspective in designing novel diamond-based biosensors and a deep knowledge of the charge-carrier transport in black diamond becomes fundamental.
RESUMEN
Pressure sensors based on diamond membranes were designed and tested for gas pressure measurement up to 6.8 MPa. The diamond film (2" diameter, 6 µm thickness)-grown by microwave plasma chemical vapor deposition on a silicon substrate-was a starting material to produce an array of membranes with different diameters in the 130-400 µm range, in order to optimize the sensor performance. Each 5 mm × 5 mm sensing element was obtained by subsequent silicon slicing. The fixed film thickness, full-scale pressure range, and sensor sensitivity were established by a proper design of the diameter of diamond membrane which represents the sensing element for differential pressure measurement. The pressure-induced deflection of the membrane was optically measured using a Fabry-Pérot interferometer formed by a single mode optical fiber front surface and the deflecting diamond film surface. The optical response of the system was numerically simulated using geometry and the elastic properties of the diamond diaphragm, and was compared with the experiments. Depending on the diamond membrane's diameter, the fabricated sensors displayed a good modulation depth of response over different full-scale ranges, from 3 to 300 bar. In view of the excellent mechanical, thermal, and chemical properties of diamond, such pressure sensors could be useful for performance in a harsh environment.
RESUMEN
One of the goals of modern dynamic radiotherapy treatments is to deliver high-dose values in the shortest irradiation time possible. In such a context, fast X-ray detectors and reliable front-end readout electronics for beam diagnostics are crucial to meet the necessary quality assurance requirements of care plans. This work describes a diamond-based detection system able to acquire and process the dose delivered by every single pulse sourced by a linear accelerator (LINAC) generating 6-MV X-ray beams. The proposed system is able to measure the intensity of X-ray pulses in a limited integration period around each pulse, thus reducing the inaccuracy induced by unnecessarily long acquisition times. Detector sensitivity under 6-MV X-photons in the 0.1-10 Gy dose range was measured to be 302.2 nC/Gy at a bias voltage of 10 V. Pulse-by-pulse measurements returned a charge-per-pulse value of 84.68 pC, in excellent agreement with the value estimated (but not directly measured) with a commercial electrometer operating in a continuous integration mode. Significantly, by intrinsically holding the acquired signal, the proposed system enables signal processing even in the millisecond period between two consecutive pulses, thus allowing for effective real-time dose-per-pulse monitoring.
RESUMEN
Thin polycrystalline diamond films chemically vapor deposited on thinned silicon substrates were used as membranes for pressure sensor fabrication by means of selective chemical etching of silicon. The sensing element is based on a simple low-finesse Fabry-Pérot (FP) interferometer. The FP cavity is defined by the end-face of a single mode fiber and the diamond diaphragm surface. Hence, pressure is evaluated by measuring the cavity length by an optoelectronic system coupled to the single mode fiber. Exploiting the excellent properties of Chemical Vapor Deposition (CVD) diamond, in terms of high hardness, low thermal expansion, and ultra-high thermal conductivity, the realized sensors have been characterized up to 16.5 MPa at room temperature. Preliminary characterizations demonstrate the feasibility of such diamond-on-Si membrane structure for pressure transduction. The proposed sensing system represents a valid alternative to conventional solutions, overcoming the drawback related to electromagnetic interference on the acquired weak signals generated by standard piezoelectric sensors.
RESUMEN
The aim of the study was to evaluate the serum and urine levels of cobalt (Co), chromium (Cr), manganese (Mn), molybdenum (Mo) and nickel (Ni) in patients who had undergone metal-on-metal hybrid surface arthroplasties on the supposition that a release of metals would occur due to the large head size of this type of implant. Metal levels were determined by using an analytical method based on sector field inductively coupled plasma mass spectrometry. Results showed a significant difference between patients and control subjects in mean levels of Co and Cr in serum (p<0.0001 and p=0.02, respectively) and in urine (p<0.0001 for both). No significant differences were observed in mean serum and urinary levels of Mn, Mo and Ni. Although the clinical consequences of these changes, if any, are unknown, further studies could be performed in a larger number of subjects implanted with a total surface arthroplasty at follow-up times over different periods.
Asunto(s)
Artroplastia de Reemplazo de Cadera/métodos , Metales Pesados/sangre , Metales Pesados/orina , Adulto , Anciano , Anciano de 80 o más Años , Artroplastia de Reemplazo de Cadera/efectos adversos , Artroplastia de Reemplazo de Cadera/instrumentación , Cromo/sangre , Cromo/orina , Cobalto/sangre , Cobalto/orina , Femenino , Estudios de Seguimiento , Humanos , Masculino , Manganeso/sangre , Manganeso/orina , Persona de Mediana Edad , Molibdeno/sangre , Molibdeno/orina , Níquel/sangre , Níquel/orina , Propiedades de Superficie , Resultado del TratamientoRESUMEN
OBJECTIVE: This study evaluated the psychopathological consequences of a single rape occurring in adult women. METHOD: The psychiatric symptoms reported by 40 women who were victims of rape during the previous 9 months as decided by a court of law were compared with the symptoms of 32 women who underwent severe, nonsexual, life-threatening events (car accidents, physical attacks, or robberies). None of the raped women had experienced previous sexual abuse during childhood or adolescence. RESULTS: The raped women showed a significantly greater prevalence of posttraumatic stress disorder, as well as sexual, eating, and mood disorders. CONCLUSIONS: These findings indicate that the psychopathological consequences of a rape could be specific and may warrant particular attention.