RESUMEN
Research on graphene-related two-dimensional (2D) materials (GR2Ms) in recent years is strongly moving from academia to industrial sectors with many new developed products and devices on the market. Characterization and quality control of the GR2Ms and their properties are critical for growing industrial translation, which requires the development of appropriate and reliable analytical methods. These challenges are recognized by International Organization for Standardization (ISO 229) and International Electrotechnical Commission (IEC 113) committees to facilitate the development of these methods and standards which are currently in progress. Toward these efforts, the aim of this study was to perform an international interlaboratory comparison (ILC), conducted under Versailles Project on Advanced Materials and Standards (VAMAS) Technical Working Area (TWA) 41 "Graphene and Related 2D Materials" to evaluate the performance (reproducibility and confidence) of the thermogravimetric analysis (TGA) method as a potential new method for chemical characterization of GR2Ms. Three different types of representative and industrially manufactured GR2Ms samples, namely, pristine few-layer graphene (FLG), graphene oxide (GO), and reduced graphene oxide (rGO), were used and supplied to ILC participants to complete the study. The TGA method performance was evaluated by a series of measurements of selected parameters of the chemical and physical properties of these GR2Ms including the number of mass loss steps, thermal stability, temperature of maximum mass change rate (Tp) for each decomposition step, and the mass contents (%) of moisture, oxygen groups, carbon, and impurities (organic and non-combustible residue). TGA measurements determining these parameters were performed using the provided optimized TGA protocol on the same GR2Ms by 12 participants across academia, industry stakeholders, and national metrology institutes. This paper presents these results with corresponding statistical analysis showing low standard deviation and statistical conformity across all participants that confirm that the TGA method can be satisfactorily used for characterization of these parameters and the chemical characterization and quality control of GR2Ms. The common measurement uncertainty for each parameter, key contribution factors were identified with explanations and recommendations for their elimination and improvements toward their implementation for the development of the ISO/IEC standard for chemical characterization of GR2Ms.
RESUMEN
The photo differential scanning calorimetry (photo-DSC) is an appropriate method to characterize photopolymers used in additive manufacturing (AM). Important process parameters such as optimal ultraviolet (UV) exposure time and reaction heat can be attained by this method. However, achieving reliable and meaningful results from photo-DSC experiments requires careful sample preparation, i.e. the selection of a suitable sample shape, sample mass and sample holder (crucible). The sample shapes drop and spread with 1.0 mg and 2.8 mg sample masses were investigated in this study. Three different times from sample preparation until the start of the measurement (0, 4 and 7 h) were tested, in order to investigate different surface effects such as oxygen-diffusion, prior UV-curing through ambient radiation and evaporation of volatile components. While the 1.0 mg spread sample shape offers the thinnest film thickness (40 µm) and thus the closest comparability to high resolution print jobs, the 2.8 mg drop shape offers a more robust sample preparation with minimized surface effects. To further reduce time-dependent surface effects, this study shows how a preexisting test protocol was shortened from 42 min to 24 min without losing measuring accuracy. Furthermore, to reduce evaporation, different covers were placed on different crucibles, which were tested over time in the device's automated sample changer (ASC) that enables automated and consecutive measurements. The combination of a cold pressed 85 µL crucible covered with a 300 µL Al2O3 crucible, which is removed shortly before the actual measurement, provides the best sample preparation for the ASC since mass loss remains below 1% for up to 10 h. Finally, two two-part resin systems, namely a methacrylate-urethane and an acrylate-epoxy based resin that are used in Digital Light Synthesis (DLS) are characterized part by part as well as in mixed state. Together with the investigation of different temperatures and atmospheres, it was possible to identify not only the part with the photoinitiator and the type of system (radical or cationic), but also a difference between methacrylates and acrylates with the aid of the photo-DSC method.