Cost-effective silicon-photonic biosensors using doped silicon detectors and a broadband source.

We propose and demonstrate a cost-effective, microring-based, silicon photonic sensor that uses doped silicon detectors and a broadband source. Shifts in the sensing microring resonances are electrically tracked by a doped second microring, which acts as both a tracking element and a photodetector. By tracking the power supplied to this second ring, as the sensing ring's resonance shifts, the effective refractive index change caused by the analyte is determined. This design reduces the cost of the system by eliminating high-cost, high-resolution tunable lasers, and is fully compatible with high-temperature fabrication processes. We report a bulk sensitivity of 61.8 nm/RIU and a system limit of detection of 9.8x10-4 RIU.

Measuring on-chip waveguide losses using a single, two-point coupled microring resonator.

We demonstrate a method for measuring on-chip waveguide losses using a single microring resonator with a tunable coupler. By tuning the power coupling to the microring and measuring the microring's through-port transmission at each power coupling, one can separate the waveguide propagation loss and the effects of the coupling to the microring. This method is tolerant of fiber-chip coupling/alignment errors and does not require the use of expensive instruments for phase response measurements. In addition, this method offers a compact solution for measuring waveguide propagation losses, only using a single microring (230 µm×190 µm, including the metal pads). We demonstrate this method by measuring the propagation losses of silicon-on-insulator rib waveguides, yielding propagation losses of 3.1-1.3 dB/cm for core widths varying from 400-600 nm.

Automated control algorithms for silicon photonic polarization receiver.

We demonstrate greedy linear descent-based, basic gradient descent-based, two-point step size gradient descent-based, and two-stage optimization method-based automated control algorithms and examine their performance for use with a silicon photonic polarization receiver. With an active feedback loop control process, time-varying arbitrary polarization states from an optical fiber can be automatically adapted and stabilized to the transverse-electric (TE) mode of a single-mode silicon waveguide. Using the proposed control algorithms, we successfully realize automated adaptations for a 10 Gb/s on-off keying signal in the polarization receiver. Based on the large-signal measurement results, the control algorithms are examined and compared with regard to the iteration number and the output response. In addition, we implemented a long-duration experiment to track, adapt, and stabilize arbitrary input polarization states using the two-point step size gradient descent-based and two-stage optimization method-based control algorithms. The experimental results show that these control algorithms enable the polarization receiver to achieve real-time and continuous polarization management.

Sub-wavelength grating-assisted polarization splitter-rotators for silicon-on-insulator platforms: erratum.

An erratum is presented to correct the caption of Fig. 1 and the citation number in Fig. 7(d) in the original article [Opt. Express 27, 17581 (2019)].

Ring resonator based polarization diversity WDM receiver.

A ring resonator based 4 channel wavelength division multiplexing (WDM) receiver with polarization diversity is demonstrated at 10 Gb/s per channel. By forming a waveguide loop between the two output ports of a polarization splitter-rotator (PSR), the input signals in the quasi-transverse-electric (quasi-TE) and the quasi-transverse-magnetic (quasi-TM) polarizations can be demultiplexed by the same set of ring resonator filters, thus reducing the number of required channel control circuits by half compared to methods which process the two polarizations individually. Large signal measurement results indicate that the design can tolerate a signal delay of up to 30% of the unit interval (UI) between the two polarizations, which implies that compensating for manufacturing variability with optical delay lines on chip is not necessary for a robust operation. The inter-channel crosstalk is found negligible down to 0.4nm (50 GHz) spacing, at which point the adjacent channel isolation is 17 dB, proving the design's compatibility for dense WDM application.

Sub-wavelength grating-assisted polarization splitter-rotators for silicon-on-insulator platforms.

We propose and demonstrate broadband, entirely mode-evolution-based, polarization splitter-rotators (PSR) using sub-wavelength grating (SWG) assisted adiabatic waveguides for two SOI platforms. Our PSRs are more compact than previously demonstrated entirely mode-evolution-based designs. The devices were fabricated using two fabrication processes and, in both cases, the measured spectra show close matches to the simulation results. One of the processes uses standard optical lithography and, hence, this is the first time that an SWG-based PSR has been experimentally implemented using such a process. Finally, measurements for arbitrary input polarizations on an active, automated polarization receiver, that uses one of our PSRs, are also presented.

Compact wavelength- and bandwidth-tunable microring modulator.

Fabrication errors currently hold back the large-scale adoption of silicon micro-ring modulators (MRMs). The ability to correct their spectral features post-fabrication is required to enable their commercialization. Here, we report and demonstrate an MRM that uses a tunable two-point coupling scheme, which maintains the MRM's compact footprint (60 µm×45 µm) and allows one to tune the MRM's operating wavelength and adjust the optical bandwidth (and/or extinction ratio). This means that one can compensate for fabrication errors and thereby improve the yields. We confirm the modulator's operation by showing NRZ and PAM-4 modulation, up to 28 Gb/s and 19.9 Gb/s, respectively. Also, the proposed tunable MRM maintains the microring's free-spectral range (FSR), which proves its compatibility for configurable and high-bandwidth DWDM applications.

Erratum: Luan, E.X.; Shoman, H.; Ratner, D.M.; Cheung, K.C.; Chrostowski, L. Silicon Photonic Biosensors Using Label-Free Detection. Sensors 2018, 18, 3519.

The authors wish to make the following corrections in their published paper in Sensors [...].

Bandwidth-tunable, FSR-free, microring-based, SOI filter with integrated contra-directional couplers.

A silicon-on-insulator (SOI), bandwidth (BW)-tunable, free-spectral-range (FSR)-free, microring resonator (MRR)-based filter is experimentally demonstrated. The device achieves an FSR-free response at its through and drop ports by using a grating-assisted coupler in one coupling region of the MRR and achieves a non-adjacent channel isolation, (nAi), for 400 GHz WDM, greater than 26.7 dB. A thermally tunable Mach-Zehnder Interferometer-based coupling scheme is also utilized to compensate for fabrication variations and enable the BW tunability of the filter. The BW of the filter can be continuously tuned from 25 to 60 GHz while maintaining an nAi greater than 26.7 dB.

Silicon Photonic Biosensors Using Label-Free Detection.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level complementary metal-oxide semiconductor (CMOS) chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.