Effect of Salvadora persica on resin-dentin bond stability.

BACKGROUND: The stability of resin-dentin interfaces is still highly questionable. The aim of this study was to evaluate the effect of Salvadora persica on resin-dentin bond durability. MATERIALS AND METHODS: Extracted human third molars were used to provide mid-coronal dentin, which was treated with 20% Salvadora persica extract for 1 min after acid-etching. Microtensile bond strength and interfacial nanoleakage were evaluated after 24 h and 6 months. A three-point flexure test was used to measure the stiffness of completely demineralized dentin sticks before and after treatment with Salvadora persica extract. The hydroxyproline release test was also used to measure collagen degradation by endogenous dentin proteases. Statistical analysis was performed using two-way ANOVA followed by post hoc Bonferroni test and unpaired t-test. P-values < 0.05 were considered statistically significant. RESULTS: The use of Salvadora persica as an additional primer with etch-and-rinse adhesive did not affect the immediate bond strengths and nanoleakage (p > 0.05). After 6 months, the bond strength of the control group decreased (p = 0.007), and nanoleakage increased (p = 0.006), while Salvadora persica group showed no significant difference in bond strength and nanoleakage compared to their 24 h groups (p > 0.05). Salvadora persica increased dentin stiffness and decreased collagen degradation (p < 0.001) compared to their controls. CONCLUSION: Salvadora persica extract pretreatment of acid-etched dentin preserved resin-dentin bonded interface for 6 months. CLINICAL SIGNIFICANCE: Durability of resin-dentin bonded interfaces is still highly questionable. Endogenous dentinal matrix metalloproteinases play an important role in degradation of dentinal collagen within such interfaces. Salvadora persica may preserve resin-dentin interfaces for longer periods of time contributing to greater clinical success and longevity of resin composite restorations.

Effect of Water Sorption and Solubility on Color Stability of Bulk-Fill Resin Composite.

AIM: The objective of this study is to compare the bulk-fill resin composite to a conventional one, as regards; water sorption, solubility, and their effect on color stability. MATERIALS AND METHODS: This study was conducted using two types of composites: Bulk-fill composite (Filtek Bulk-Fill) and nanohybrid composite for control (Filtek Z250 XT). Specimens were prepared using a ring mold, 10 from each material. Specimens were desiccated, then weighed in a digital balance until a stable mass was acquired. For water sorption test, specimens were immersed in distilled water and placed in a lightproof incubator at 37 ± 1°C and the mass was measured weekly for 8 weeks. For solubility test, specimens were desiccated again in the desiccator until a stable mass was achieved. A spectropho-tometer was used to record the baseline color measurements prior to water immersion and weekly for 8 weeks. RESULTS: Bulk-fill composite showed higher water sorption value and lower water solubility values compared with that of the conventional one. No statistically significant difference was found for water sorption (p = 0.104) or water solubility (p = 0.098) between groups. The mean ΔE was lower in bulk-fill than conventional composite, and results showed a statistically significant difference (p = 0.009). CONCLUSION: Bulk-fill resin composite yielded better color stability and similar water sorption and solubility values. CLINICAL SIGNIFICANCE: Bulk-fill resin composite can be used in esthetically concerned patients.

Adhesive sealing of dentin surfaces in vitro: A review.

PURPOSE: This review describes the evolution of the use of dental adhesives to form a tight seal of freshly prepared dentin to protect the pulp from bacterial products, during the time between crown preparation and final cementation of full crowns. The evolution of these "immediate dentin sealants" follows the evolution of dental adhesives, in general. That is, they began with multiple-step, etch-and-rinse adhesives, and then switched to the use of simplified adhesives. METHODS: Literature was reviewed for evidence that bacteria or bacterial products diffusing across dentin can irritate pulpal tissues before and after smear layer removal. Smear layers can be solubilized by plaque organisms within 7-10 days if they are directly exposed to oral fluids. It is likely that smear layers covered by temporary restorations may last more than 1 month. As long as smear layers remain in place, they can partially seal dentin. Thus, many in vitro studies evaluating the sealing ability of adhesive resins use smear layer-covered dentin as a reference condition. Surprisingly, many adhesives do not seal dentin as well as do smear layers. RESULTS: Both in vitro and in vivo studies show that resin- covered dentin allows dentin fluid to cross polymerized resins. The use of simplified single bottle adhesives to seal dentin was a step backwards. Currently, most authorities use either 3-step adhesives such as Scotchbond Multi-Purpose or OptiBond FL or two-step self-etching primer adhesives, such as Clearfil SE, Unifil Bond or AdheSE.

Sealing Ability of Four Calcium Containing Cements used for Repairing Furcal Perforations in Primary Molars: An in vitro study.

AIM: The aim of this study was to compare the sealing ability of mineral trioxide aggregate (MTA), Portland cement (PC), Biodentine(TM) and Tech biosealer in repairing furcal perforations in primary molars using the fluid-filtration technique. MATERIALS AND METHODS: Fifty freshly extracted maxillary second primary molars were sectioned horizontally at the furcation region to create dentin disks of 1.5 mm (+ 0.1 mm) thickness. Five disks were not perforated and served as negative controls. In the remaining 45 disks, furcation perforations were prepared. Five disks did not receive furcation repair and served as positive controls. The remaining 40 disks were then randomly divided into four equal groups (10 disks in each group). Perforations were repaired with: MTA, PC, Biodentine(TM) or Tech Biosealer. The sealing ability of the tested materials was evaluated by measuring microleakage for each disk after four different storage periods: 24-hour, 1-month, 6-month and 1-year storage using fluid-filtration. Comparisons between the four materials and the four time periods were done using the two-way analysis of variance and the Scheffe multiple comparisons test. RESULTS: There was no significant difference between the mean microleakage values obtained in the four tested materials after 24 hours, 1, 6 month and 1 year. However, microleakage values for each individual material were significantly higher at 24 hours than at the other time intervals. CONCLUSION: Mineral trioxide aggregate, PC, Biodentine(TM) and Tech biosealer showed similar capabilities in sealing the furcal perforations of the primary molars, where the sealing ability improved over time for each individual material.