Regulating Water Adsorption Sites of Keto-Enamine COF by Base Exfoliation and Deprotonation for Enhanced Humidity Response.

Covalent organic framework (COF) has received much attention owing to its unique framework structure formed by diverse organic units. However, challenges, including low conductivity, structure instability, and limited control of adsorption and desorption processes, stimulate the modification of COF in electronic sensors. Herein, inspired by the alterable structure of COF in different solvents, a facile base exfoliation and deprotonation method is proposed to regulate the water adsorption sites and improve the intrinsic conductivity of TpPa-1 COF. TpPa-1 COF powders are exfoliated to nanosheets to increase water adsorption, while the deprotonation is utilized to adjust the affinity of water molecules on TpPa-1 COF framework, contributing to water accumulation in the 1D pores. The as-fabricated TpPa-1 COF sensor exhibits a decreased recovery time from 419 to 49 s, forming a linear relation between relative humidity (RH) value and humidity response. The excellent chemical stability of the covalent bond of TpPa-1 COF contributes to the excellent stable device performance in 30 days, promoting further integration and data analysis in respiration monitoring.

N-doped TiO2/rGO: synthesis, structure, optical characteristics, and humidity sensing applications.

In the current study, the effect of rGO ratio on the N-dopped TiO2has been synthesized through sol-gel method. The prepared N-doped TiO2/rGO composites were examined for humidity sensing applications. The relationship between optical properties and the humidity sensing properties was studied. The structure, morphology, and bonding interaction have been examined using XRD, FT-IR, PL and HRTEM respectively. The average particle size as estimated from XRD and HRTEM was found to be about 9 nm. The optical properties have been studied using UV/ Vis. Spectroscopy. Further, optical parameters including refractive index and optical band gap energy have been estimated. The humidity sensing behavior of the resultant composites were evaluated in a wide range of humidity (7%-97% RH) at different testing frequencies. The optical band gap was found to be decreased as the amount of rGO increase. Among all prepared samples, both the optical parameters and humidity sensing experiments confirmed that the 0.5% rGO@N-dopped TiO2sample is the best candidate for the humidity sensing applications. The best optimum testing frequency was demonstrated to be 50 Hz. The sensor demonstrates a fast response and recovery times of 13 s and 33 s with low hysteresis and large sensitivity. The humidity sensing mechanism was studied using complex impedance spectroscopy at different RH levels under testing frequency range from 50 Hz to 5 MHz and testing voltage of 1 VAC. The produced structure demonstrated a promising material for humidity measuring devices.

Applications of Chipless RFID Humidity Sensors to Smart Packaging Solutions.

Packaging solutions have recently evolved to become smart and intelligent thanks to technologies such as RFID tracking and communication systems, but the integration of sensing functionality in these systems is still under active development. In this paper, chipless RFID humidity sensors suitable for smart packaging are proposed together with a novel strategy to tune their performances and their operating range. The sensors are flexible, fast, low-cost and easy to fabricate and can be read wirelessly. The sensitivity and the humidity range where they can be used are adjustable by changing one of the sensor's structural parameters. Moreover, these sensors are proposed as double parameter sensors, using both the frequency shift and the intensity variation of the resonance peak for the measure of the relative humidity. The results show that the sensitivity can vary remarkably among the sensors proposed, together with the operative range. The sensor suitability in two specific smart packaging applications is discussed. In the first case, a threshold sensor in the low-humidity range for package integrity verification is analyzed, and in the second case, a more complex measurement of humidity in non-hermetic packages is investigated. The discussion shows that the sensor configuration can easily be adapted to the different application needs.

Femtosecond Laser Inscribed Excessively Tilted Fiber Grating for Humidity Sensing.

We propose a humidity sensor using an excessively tilted fiber grating (Ex-TFG) coated with agarose fabricated using femtosecond laser processing. The processed grating showcases remarkable differentiation between TE and TM modes, achieving an exceptionally narrow bandwidth of approximately 1.5 nm and an impressive modulation depth of up to 15 dB for both modes. We exposed the agarose-coated TFG sensor to various relative humidity levels and monitored the resonance wavelength to test its humidity sensing capability. Our findings demonstrated that the sensor exhibited a rapid response time (2-4 s) and showed a high response sensitivity (18.5 pm/%RH) between the humidity changes and the resonant wavelength shifts. The high sensitivity, linearity, repeatability, low hysteresis, and excellent long-term stability of the TFG humidity sensor, as demonstrated in our experimental results, make it an attractive option for environmental monitoring or biomedical diagnosis.

Dehydration Dynamics in Terrestrial Arthropods: From Water Sensing to Trophic Interactions.

Since the transition from water to land, maintaining water balance has been a key challenge for terrestrial arthropods. We explore factors that allow terrestrial arthropods to survive within a variably dry world and how they shape ecological interactions. Detection of water and hydration is critical for maintaining water content. Efficient regulation of internal water content is accomplished by excretory and osmoregulatory systems that balance water intake and loss. Biochemical and physiological responses are necessary as water content declines to prevent and repair the damage that occurs during dehydration. Desiccation avoidance can occur seasonally or daily via a move to more favorable areas. Dehydration and its avoidance have ecological impacts that extend beyond a single species to alter trophic interactions. As climate changes, evolutionary and ecological processes will be critical to species survival during drought.

Fabrication of polyaniline/graphene oxide composites for implementation in humidity sensing.

This work reports the measurement of impedance variations under various humidity conditions at frequency ranges between 100 Hz and 5 MHz. An electrochemical polymerization process has been used in the synthesis including varying the mass ratios of graphene oxide (GO) in polyaniline. An electrochemical deposition method has been used to produce a sample film on an indium tin oxide glass slide. The percentage relative humidity (RH%) of the samples has been estimated to be 20-90%. Impedance and humidity had an inverse relationship, i.e. the impedance value decreased with an increase in humidity. In contrast with platinum capacitive humidity sensors (HS), the GO-based HS had a sensitivity of 75-99%, which was ~10-fold more than that of traditional sensors. With three different parameter weight % of GO, the frequency range have been 100 Hz to 5 MHz and RH% has been found to 20-90%. The HS showed a fast response and recovery time. Therefore, GO appears to be a useful material for building HS with high sensitivity for a comprehensive approach.

Study of Intermolecular Reconfiguration of Flexible COF-5 Film and Its Ultra-high Chemiresistive Humidity Sensitivity.

Recently, abundant active materials are developed to achieve the wearable detection of human body humidity. However, the limited response signal and sensitivity restrict further application due to their moderate affinity to water. Herein, we propose a flexible COF-5 film synthesized by a brief vapor-assisted method at room temperature. Intermediates are calculated by DFT simulation to investigate the interaction between COF-5 and water. The adsorption and desorption of water molecule result in a reversible deformation of COF layers while creating new conductive path by π-π stacking. The as-prepared COF-5 films are applied to the flexible humidity sensors, exhibiting a resistance change in 4 orders of magnitude with remarkable linear relation between log function of resistance and relative humidity (RH) in 11 %-98 % RH range. Applications including respiratory monitoring and non-contact switch are tested, providing a promising prospect for the detection of human body humidity.

Characteristic Analysis of a Chipless RFID Sensor Based on Multi-Parameter Sensing and an Intelligent Detection Method.

Chipless radio frequency identification (RFID) technology has been widely used in the field of structural health monitoring (SHM), but most of the current research mainly focuses on the detection of mechanical properties and there are few studies on the multi-physical parameters (for example, temperature and humidity) in the climatic environment around the structure. Thus, it is necessary to design a small and compact sensor for multi-parameter detection. This paper proposes a multi-parameter chipless RFID sensor based on microstrip coupling, which supports 4-bit ID code and integrates two detection functions of temperature and humidity. Through linear normalization fitting, the sensitivity of the sensor is about 2.18 MHz/RH in the ambient relative humidity test and the sensitivity of the sensor is about 898.63 KHz/°C in the experimental test of water bath heating from 24.6 °C to 75 °C. In addition, this paper proposes an engineering application detection method, designs a lightweight dynamic spectrum detection and wireless transmission platform based on a lightweight vector network analyzer (VNA) and realizes the real-time extraction and transmission of RFID spectrum sensing data. The means are more flexible and economical than traditional experimental scenarios.

Controllable preparation of ultrathin MXene nanosheets and their excellent QCM humidity sensing properties enhanced by fluoride doping.

A 2D ultrathin MXene nanosheet was prepared under controlled conditions and employed as a sensitive film to construct a QCM (quartz crystal microbalance) humidity sensor by a dip coating method. The MXene nanosheets were obtained by dislodging the element A from the MAX phase by a facile liquid phase etching method. The morphology and composition of the MXene nanosheets were characterized by means of a number of advanced instruments. It was found that the sample is an ultrathin graphene-like nanosheet. The sensing test results showed that the sensor has a 12.8 Hz/% RH sensitivity, 6 s and 2 s (@ 90%) response/recovery time, maximum humidity hysteresis of 1.16% RH, good stability, and selectivity. Finally, the enhanced humidity response mechanism of the MXene nanosheets was explored by density-functional theory (DFT) calculation and experimental verification. The DFT simulation together with comparison of fluoride-free sample revealed that F elements on the surface of the MXene nanosheets play a more important role in improving humidity responses than OH groups. The results present a new strategy to enhance humidity sensing performance of sensing materials by F- doping or decoration. Thus, the sensor has bright potential for humidity sensing.

Rapid Fabrication of Renewable Carbon Fibres by Plasma Arc Discharge and Their Humidity Sensing Properties.

Submicron-sized carbon fibres have been attracting research interest due to their outstanding mechanical and electrical properties. However, the non-renewable resources and their complex fabrication processes limit the scalability and pose difficulties for the utilisation of these materials. Here, we investigate the use of plasma arc technology to convert renewable electrospun lignin fibres into a new kind of carbon fibre with a globular and porous microstructure. The influence of arc currents (up to 60 A) on the structural and morphological properties of as-prepared carbon fibres is discussed. Owing to the catalyst-free synthesis, high purity micro-structured carbon fibres with nanocrystalline graphitic domains are produced. Furthermore, the humidity sensing characteristics of the treated fibres at room temperature (23 °C) are demonstrated. Sensors produced from these carbon fibres exhibit good humidity response and repeatability in the range of 30% to 80% relative humidity (RH) and an excellent sensitivity (0.81/%RH) in the high RH regime (60-80%). These results demonstrate that the plasma arc technology has great potential for the development of sustainable, lignin-based carbon fibres for a broad range of application in electronics, sensors and energy storage.

Electrospun Nickel Manganite (NiMn2O4) Nanocrystalline Fibers for Humidity and Temperature Sensing.

Nickel manganite nanocrystalline fibers were obtained by electrospinning and subsequent calcination at 400 °C. As-spun fibers were characterized by TG/DTA, Scanning Electron Microscopy and FT-IR spectroscopy analysis. X-ray diffraction and FT-IR spectroscopy analysis confirmed the formation of nickel manganite with a cubic spinel structure, while N2 physisorption at 77 K enabled determination of the BET specific surface area as 25.3 m2/g and (BJH) mesopore volume as 21.5 m2/g. The material constant (B) of the nanocrystalline nickel manganite fibers applied by drop-casting on test interdigitated electrodes on alumina substrate, dried at room temperature, was determined as 4379 K in the 20-50 °C temperature range and a temperature sensitivity of -4.95%/K at room temperature (25 °C). The change of impedance with relative humidity was monitored at 25 and 50 °C for a relative humidity (RH) change of 40 to 90% in the 42 Hzπ1 MHz frequency range. At 100 Hz and 25 °C, the sensitivity of 327.36 ± 80.12 kΩ/%RH was determined, showing that nickel manganite obtained by electrospinning has potential as a multifunctional material for combined humidity and temperature sensing.

Full-Self-Powered Humidity Sensor Based on Electrochemical Aluminum-Water Reaction.

A detailed examination of the principle of operation behind the functioning of the full-self-powered humidity sensor is presented. The sensor has been realized as a structure consisting of an interdigitated capacitor with aluminum thin-film digits. In this work, the details of its fabrication and activation are described in detail. The performed XRD, FTIR, SEM, AFM, and EIS analyses, as well as noise measurements, revealed that the dominant process of electricity generation is the electrochemical reaction between the sensor's aluminum electrodes and the water from humid air in the presence of oxygen, which was the main goal of this work. The response of the sensor to human breath is also presented as a demonstration of its possible practical application.

Plant Wearable Sensors Based on FBG Technology for Growth and Microclimate Monitoring.

Plants are primary resources for oxygen and foods whose production is fundamental for our life. However, diseases and pests may interfere with plant growth and cause a significant reduction of both the quality and quantity of agriculture products. Increasing agricultural productivity is crucial for poverty reduction and food security improvements. For this reason, the 2030 Agenda for Sustainable Development gives a central role to agriculture by promoting a strong technological innovation for advancing sustainable practices at the plant level. To accomplish this aim, recently, wearable sensors and flexible electronics have been extended from humans to plants for measuring elongation, microclimate, and stressing factors that may affect the plant's healthy growth. Unexpectedly, fiber Bragg gratings (FBGs), which are very popular in health monitoring applications ranging from civil infrastructures to the human body, are still overlooked for the agriculture sector. In this work, for the first time, plant wearables based on FBG technology are proposed for the continuous and simultaneous monitoring of plant growth and environmental parameters (i.e., temperature and humidity) in real settings. The promising results demonstrated the feasibility of FBG-based sensors to work in real situations by holding the promise to advance continuous and accurate plant health growth monitoring techniques.

Humidity-Sensing Chipless RFID Tag with Enhanced Sensitivity Using an Interdigital Capacitor Structure.

An eight-bit chipless radio frequency identification tag providing humidity sensing and identification information is proposed. A compact, enhanced-sensitivity resonator based on an interdigital capacitor (IDC) structure is designed for humidity sensing, whereas seven electric-field-coupled inductor capacitor (ELC) resonators are used for identification information. These eight resonators are placed in a two-by-four array arrangement. A step-by-step investigation for the effect of varying the number of elements and array configuration on the resonant frequency and radar cross-section (RCS) magnitude of the IDC resonator is conducted. The RCS value of the resonant peak frequency for the IDC resonator increases as the number of array elements placed nearby increases due to the mutual coupling among the elements, and the increase in the RCS value becomes larger as the number of arrays increases in the vertical direction. Polyvinyl alcohol (PVA) is coated on the IDC-based resonator at a thickness of 0.02 mm. A non-reflective temperature and humidity chamber is fabricated using Styrofoam, and the relative humidity (RH) is varied from 50% to 80% in 10% intervals at 25 °C in order to measure a bistatic RCS of the proposed tag. The humidity sensing performance of the IDC resonator in the proposed tag is measured by the shift in the resonant peak frequency and the RCS value, and is compared with a single ELC resonator. Experiment results show that when RH increased from 50% to 80%, the sensitivities of both the resonant peak frequency and the RCS value of the IDC resonator were better than those of the ELC resonator. The variation in the RCS value is much larger compared to the resonant peak frequency for both IDC and ELC resonators. In addition, the resonant peak frequency and RCS value of the PVA-coated IDC-based resonator change, whereas those of the other seven resonators without a PVA coating do not change.

Real-Time Humidity Measurement during Sports Activity using Optical Fibre Sensing.

An optical fibre sensor for monitoring relative humidity (RH) changes during exercise is demonstrated. The humidity sensor comprises a tip coating of poly (allylamine hydrochloride) (PAH)/silica nanoparticles (SiO2 NPs) deposited using the layer-by-layer technique. An uncoated fibre is employed to compensate for bending losses that are likely to occur during movement. A linear fit to the response of the sensing system to RH demonstrates a sensitivity of 3.02 mV/% (R2 = 0.96), hysteresis ± 1.17% RH when 11 bilayers of PAH/SiO2 NPs are coated on the tip of the fibre. The performance of two different textiles (100% cotton and 100% polyester) were tested in real-time relative humidity measurement for 10 healthy volunteers. The results demonstrate the moisture wicking properties of polyester in that the relative humidity dropped more rapidly after cessation of exercise compared to cotton. The approach has the potential to be used to monitor sports performance and by clothing developers for characterising different garment designs.

CdSSe nanowire-chip based wearable sweat sensor.

BACKGROUND: Sweat, as an easily accessible bodily fluid, is enriched with a lot of physiological and health information. A portable and wearable sweat sensor is an important device for an on-body health monitoring. However, there are only few such devices to monitor sweat. Based on the fact that sweat is mainly composed of moisture and salt which is much more abundant than other trace ions in sweat, a new route is proposed to realize wearable sweat sensors using CdSSe nanowire-chips coated with a polyimide (PI) membrane. RESULTS: Firstly, the composition-graded CdS1-xSex (x = 0-1) nanowire-chip based sensor shows good photo-sensitivity and stress sensitivity which induces linear humidity dependent conductivity. This indicates good moisture response with a maximum responsivity (dI/I) 244% at 80% relative humidity (RH) even in the dark. Furthermore, the linear current decrease with salt increase illustrates the chip sensor has a good salt-sensing ability with the best salt dependent responsivity of 80%, which guarantees the high prediction accuracy in sweat sensing. The sensor current is further proven to nonlinearly correlate to the amount of sweat with excellent stability, reproducibility and recoverability. The wearable sweat sensor is finally applied on-body real-time sweat analysis, showing good consistence with the body status during indoor exercise. CONCLUSIONS: These results suggest that this CdSSe nanowire-chip based PI-coated integrated sensor, combined with inorganic and organic functional layers, provides a simple and reliable method to build up diverse portable and wearable devices for the applications on healthcare and athletic status.

Low-Hysteresis and Fast Response Time Humidity Sensors Using Suspended Functionalized Carbon Nanotubes.

A humidity sensor using suspended carbon nanotubes (CNTs) was fabricated using a low-temperature surface micromachining process. The CNTs were functionalized with carboxylic acid groups that facilitated the interaction of water vapor with the CNTs. The humidity sensor showed a response time of 12 s and a recovery time of 47 s, along with superior hysteresis and stable performance. The hysteresis curve area of the suspended structure is 3.6, a 3.2-fold reduction in comparison to the non-suspended structure. A comparative study between suspended and non-suspended devices highlights the advantages of using a suspended architecture.

Enhanced Humidity Sensing Response of SnO2/Silicon Nanopillar Array by UV Irradiation.

In this work, a silicon nanopillar array was created with nanosphere lithography. SnO2 film was deposited on this nanostructure by magnetron sputtering to form an SnO2/silicon nanopillar array sensor. The humidity sensitivity, response time, and recovery time were all measured at room temperature (25 °C) with UV or without UV irradiation. As a result, the humidity sensitivity properties were improved by enlarging the specific surface area with ordered nanopillars and irradiating with UV light. These results indicate that nanostructure sensors have potential applications in the field of sensors.

Distributed Fiberoptic Sensor for Simultaneous Humidity and Temperature Monitoring Based on Polyimide-Coated Optical Fibers.

Along temperature, humidity is one of the principal environmental factors that plays an important role in various application areas. Presented work investigates possibility of distributed fiberoptic humidity monitoring based on humidity-induced strain measurement in polyimide (PI)-coated optical fibers. Characterization of relative humidity (RH) and temperature response of four different commercial PI- and one acrylate-coated fiber was performed using optical backscattering reflectometry (OBR). The study addresses issues of temperature-humidity cross-sensitivity, fiber response stability, repeatability, and the influence of annealing. Acrylate-coated fiber exhibited rather unfavorable nonlinear RH response with strong temperature dependence, which makes it unsuitable for humidity sensing applications. On the other hand, humidity response of PI-coated fibers showed good linearity with fiber sensitivity slightly decreasing at rising temperatures. In the tested range, temperature sensitivity of the fibers remained humidity independent. Thermal annealing was shown to considerably improve and stabilize fiber RH response. Based on performed analysis, a 20 m sensor using the optimal PI-coated fibers was proposed and constructed. The sensor uses dual sensing fiber configuration for mutual decoupling and simultaneous measurement of temperature and RH variations. Using OBR, distributed dual temperature-RH monitoring with cm spatial resolution was demonstrated for the first time.

Enhanced Humidity Sensitivity with Silicon Nanopillar Array by UV Light.

The sensitivity of silicon nanopillar array for relative humidity (RH) with UV illumination was investigated in this work. The silicon nanopillar array was prepared by nanosphere lithography. Electrical measurements were performed on its sensing performance with and without UV irradiation. It was found that UV light improved the humidity sensitivity with different UV light wavelengths and power. The sensor response and recovery time were reduced. Furthermore, the turn-on threshold voltage and the operating voltage both decreased. These sensing characteristics can mainly be attributed to the electron-hole pairs generated by UV light. These electron-hole pairs promote the adsorption and desorption processes. The results indicate that silicon nanopillar array materials with UV irradiation might be competitive as novel sensing materials for fabricating humidity sensors with high performances.