New tree height allometries derived from terrestrial laser scanning reveal substantial discrepancies with forest inventory methods in tropical rainforests.

Tree allometric models, essential for monitoring and predicting terrestrial carbon stocks, are traditionally built on global databases with forest inventory measurements of stem diameter (D) and tree height (H). However, these databases often combine H measurements obtained through various measurement methods, each with distinct error patterns, affecting the resulting H:D allometries. In recent decades, terrestrial laser scanning (TLS) has emerged as a widely accepted method for accurate, non-destructive tree structural measurements. This study used TLS data to evaluate the prediction accuracy of forest inventory-based H:D allometries and to develop more accurate pantropical allometries. We considered 19 tropical rainforest plots across four continents. Eleven plots had forest inventory and RIEGL VZ-400(i) TLS-based D and H data, allowing accuracy assessment of local forest inventory-based H:D allometries. Additionally, TLS-based data from 1951 trees from all 19 plots were used to create new pantropical H:D allometries for tropical rainforests. Our findings reveal that in most plots, forest inventory-based H:D allometries underestimated H compared with TLS-based allometries. For 30-metre-tall trees, these underestimations varied from -1.6 m (-5.3%) to -7.5 m (-25.4%). In the Malaysian plot with trees reaching up to 77 m in height, the underestimation was as much as -31.7 m (-41.3%). We propose a TLS-based pantropical H:D allometry, incorporating maximum climatological water deficit for site effects, with a mean uncertainty of 19.1% and a mean bias of -4.8%. While the mean uncertainty is roughly 2.3% greater than that of the Chave2014 model, this model demonstrates more consistent uncertainties across tree size and delivers less biased estimates of H (with a reduction of 8.23%). In summary, recognizing the errors in H measurements from forest inventory methods is vital, as they can propagate into the allometries they inform. This study underscores the potential of TLS for accurate H and D measurements in tropical rainforests, essential for refining tree allometries.

Laboratory Investigations of the Leica RTC360 Laser Scanner-Distance Measuring Performance.

A Leica RTC360 laser scanner was investigated using a linear horizontal comparator system with four targets of different reflectance. Several thousand panorama scans were conducted along the 30 m long comparator, basically in 40 mm steps. For a selected target, more detailed investigations were carried out with a 2 mm step width for a 2 m wide section. The absolute offset between the scanner and the relative interferometer measurements was determined with a calibrated total station. The investigations revealed several systematic effects like an offset in the distance measurement of about 1.3 mm. Furthermore, sections with stochastic behavior as well as sections with pseudo-cyclic parts were observed, depending on the reflectance of the target. The deterministic sections showed curved and striped patterns with some discontinuities of about 2 mm at 20 m, resulting in a saw-tooth like pattern along the distances. Within all the experiments, the distance deviations were below the manufacturer specifications of the 3D point accuracy. However, it was demonstrated that the distance measurements had clear systematic components. In using these new findings, the specification of the measurement "noise" in the data sheet has to be seen as critical.

Automated Phenotypic Trait Extraction for Rice Plant Using Terrestrial Laser Scanning Data.

To quickly obtain rice plant phenotypic traits, this study put forward the computational process of six rice phenotype features (e.g., crown diameter, perimeter of stem, plant height, surface area, volume, and projected leaf area) using terrestrial laser scanning (TLS) data, and proposed the extraction method for the tiller number of rice plants. Specifically, for the first time, we designed and developed an automated phenotype extraction tool for rice plants with a three-layer architecture based on the PyQt5 framework and Open3D library. The results show that the linear coefficients of determination (R2) between the measured values and the extracted values marked a better reliability among the selected four verification features. The root mean square error (RMSE) of crown diameter, perimeter of stem, and plant height is stable at the centimeter level, and that of the tiller number is as low as 1.63. The relative root mean squared error (RRMSE) of crown diameter, plant height, and tiller number stays within 10%, and that of perimeter of stem is 18.29%. In addition, the user-friendly automatic extraction tool can efficiently extract the phenotypic features of rice plant, and provide a convenient tool for quickly gaining phenotypic trait features of rice plant point clouds. However, the comparison and verification of phenotype feature extraction results supported by more rice plant sample data, as well as the improvement of accuracy algorithms, remain as the focus of our future research. The study can offer a reference for crop phenotype extraction using 3D point clouds.

ARM4CH: A Methodology for Autonomous Reality Modelling for Cultural Heritage.

Nowadays, the use of advanced sensors, such as terrestrial, mobile 3D scanners and photogrammetric imaging, has become the prevalent practice for 3D Reality Modeling (RM) and the digitization of large-scale monuments of Cultural Heritage (CH). In practice, this process is heavily related to the expertise of the surveying team handling the laborious planning and time-consuming execution of the 3D scanning process tailored to each site's specific requirements and constraints. To minimize human intervention, this paper proposes a novel methodology for autonomous 3D Reality Modeling of CH monuments by employing autonomous robotic agents equipped with the appropriate sensors. These autonomous robotic agents are able to carry out the 3D RM process in a systematic, repeatable, and accurate approach. The outcomes of this automated process may also find applications in digital twin platforms, facilitating secure monitoring and the management of cultural heritage sites and spaces, in both indoor and outdoor environments. The main purpose of this paper is the initial release of an Industry 4.0-based methodology for reality modeling and the survey of cultural spaces in the scientific community, which will be evaluated in real-life scenarios in future research.

Assessment of Panorama Photogrammetry as a Tool for Long-Range Deformation Monitoring.

This study investigates panorama photogrammetry (PPh) as a potential method to collect massive 3D information for long-range deformation monitoring. Particularly, this study focuses on areas with measuring restrictions, i.e., inaccessible objects and distances above 0.6 km. Under these particular conditions, geodetic techniques based on Electromagnetic Distance Meters (EDMs) or Total Stations (TSs) can provide coordinates with a precision better than 1 cm, but only for a limited number of discrete points. For mass capture, Terrestrial Laser Scanning (TLS) is normally the preferred solution, but long-range instruments are expensive, and drawbacks such as weak return signals and non-automatic target recognition appear. As an alternative, PPh is investigated in the well-controlled area of La Muela in Cortes de Pallas, where images are automatically captured from geodetic pillars using a GigaPan device, processed, and then rigorously compared to TLS point clouds. The results obtained after integrating both techniques into a high-accuracy geodetic reference frame show that PPh and TLS provide similar precision to within approximately 4 cm in the range of 0.6-1.0 km. Therefore, considering cost-effectiveness and ease of use, the proposed method can be considered a low-cost alternative to TLS for long-range deformation monitoring.

Template-Guided Hierarchical Multi-View Registration Framework of Unordered Bridge Terrestrial Laser Scanning Data.

The registration of bridge point cloud data (PCD) is an important preprocessing step for tasks such as bridge modeling, deformation detection, and bridge health monitoring. However, most existing research on bridge PCD registration only focused on pairwise registration, and payed insufficient attention to multi-view registration. In addition, to recover the overlaps of unordered multiple scans and obtain the merging order, extensive pairwise matching and the creation of a fully connected graph of all scans are often required, resulting in low efficiency. To address these issues, this paper proposes a marker-free template-guided method to align multiple unordered bridge PCD to a global coordinate system. Firstly, by aligning each scan to a given registration template, the overlaps between all the scans are recovered. Secondly, a fully connected graph is created based on the overlaps and scanning locations, and then a graph-partition algorithm is utilized to construct the scan-blocks. Then, the coarse-to-fine registration is performed within each scan-block, and the transformation matrix of coarse registration is obtained using an intelligent optimization algorithm. Finally, global block-to-block registration is performed to align all scans to a unified coordinate reference system. We tested our framework on different bridge point cloud datasets, including a suspension bridge and a continuous rigid frame bridge, to evaluate its accuracy. Experimental results demonstrate that our method has high accuracy.

Laser Scanner-Based Hyperboloid Cooling Tower Geometry Inspection: Thickness and Deformation Mapping.

Hyperboloid cooling towers are counted among the largest cast-in-place industrial structures. They are an essential element of cooling systems used in many power plants in service today. Their main structural component, a reinforced-concrete shell in the form of a one-sheet hyperboloid with bidirectional curvature continuity, makes them stand out against other towers and poses very high construction and service requirements. The safe service and adequate durability of the hyperboloid structure are guaranteed by the proper geometric parameters of the reinforced-concrete shell and monitoring of their condition over time. This article presents an original concept for employing terrestrial laser scanning to conduct an end-to-end assessment of the geometric condition of a hyperboloid cooling tower as required by industry standards. The novelty of the proposed solution lies in the use of measurements of the interior of the structure to determine the actual thickness of the hyperboloid shell, which is generally disregarded in geometric measurements of such objects. The proposal involves several strategies and procedures for a reliable verification of the structure's verticality, the detection of signs of ovalisation of the shell, the estimation of the parameters of the structure's theoretical model, and the analysis of the distribution of the thickness and geometric imperfections of the reinforced-concrete shell. The idea behind the method for determining the actual thickness of the shell (including its variation due to repairs and reinforcement operations), which is generally disregarded when measuring the geometry of such structures, is to estimate the distance between point clouds of the internal and external surfaces of the structure using the M3C2 algorithm principle. As a particularly dangerous geometric anomaly of hyperboloid cooling towers, shell ovalisation is detected with an innovative analysis of the bimodality of the frequency distribution of radial deviations in horizontal cross-sections. The concept of a complete assessment of the geometry of a hyperboloid cooling tower was devised and validated using three measurement series of a structure that has been continuously in service for fifty years. The results are consistent with data found in design and service documents. We identified a permanent tilt of the structure's axis to the northeast and geometric imperfections of the hyperboloid shell from -0.125 m to +0.136 m. The results also demonstrated no advancing deformation of the hyperboloid shell over a two-year research period, which is vital for its further use.

The role of vegetation structural diversity in regulating the microclimate of human-modified tropical ecosystems.

Vegetation regulates microclimate stability through biophysical mechanisms such as evaporation, transpiration and shading. Therefore, thermal conditions in tree-dominated habitats will frequently differ significantly from standardized free-air temperature measurements. The ability of forests to buffer temperatures nominates them as potential sanctuaries for tree species intolerant to the increasingly challenging thermal conditions established by climate change. Although many factors influencing thermal conditions beneath the vegetation cover have been ascertained, the role of three-dimensional vegetation structure in regulating the understory microclimate remains understudied. Recent advances in remote sensing technologies, such as terrestrial laser scanning, have allowed scientists to capture the three-dimensional structural heterogeneity of vegetation with a high level of accuracy. Here, we examined the relationships between vegetation structure parametrized from voxelized laser scanning point clouds, air and soil temperature ranges, as well as offsets between field-measured temperatures and gridded free-air temperature estimates in 17 sites in a tropical mountain ecosystem in Southeast Kenya. Structural diversity generally exerted a cooling effect on understory temperatures, but vertical diversity and stratification explained more variation in the understory air and soil temperature ranges (30%-40%) than canopy cover (27%), plant area index (24%) and average stand height (23%). We also observed that the combined effects of stratification, canopy cover and elevation explained more than half of the variation (53%) in understory air temperature ranges. Stratification's attenuating effect was consistent across different levels of elevation. Temperature offsets between field measurements and free-air estimates were predominantly controlled by elevation, but stratification and structural diversity were influential predictors of maximum and median temperature offsets. Moreover, stable understory temperatures were strongly associated with a large offset in daytime maximum temperatures, suggesting that structural diversity primarily contributes to thermal stability by cooling daytime maximum temperatures. Our findings shed light on the thermal influence of vertical vegetation structure and, in the context of tropical land-use change, suggest that decision-makers aiming to mitigate the thermal impacts of land conversion should prioritize management practices that preserve structural diversity by retaining uneven-aged trees and mixing plant species of varying sizes, e.g., silvopastoral, or agroforestry systems.

Damage to living trees contributes to almost half of the biomass losses in tropical forests.

Accurate estimates of forest biomass stocks and fluxes are needed to quantify global carbon budgets and assess the response of forests to climate change. However, most forest inventories consider tree mortality as the only aboveground biomass (AGB) loss without accounting for losses via damage to living trees: branchfall, trunk breakage, and wood decay. Here, we use ~151,000 annual records of tree survival and structural completeness to compare AGB loss via damage to living trees to total AGB loss (mortality + damage) in seven tropical forests widely distributed across environmental conditions. We find that 42% (3.62 Mg ha-1 year-1 ; 95% confidence interval [CI] 2.36-5.25) of total AGB loss (8.72 Mg ha-1 year-1 ; CI 5.57-12.86) is due to damage to living trees. Total AGB loss was highly variable among forests, but these differences were mainly caused by site variability in damage-related AGB losses rather than by mortality-related AGB losses. We show that conventional forest inventories overestimate stand-level AGB stocks by 4% (1%-17% range across forests) because assume structurally complete trees, underestimate total AGB loss by 29% (6%-57% range across forests) due to overlooked damage-related AGB losses, and overestimate AGB loss via mortality by 22% (7%-80% range across forests) because of the assumption that trees are undamaged before dying. Our results indicate that forest carbon fluxes are higher than previously thought. Damage on living trees is an underappreciated component of the forest carbon cycle that is likely to become even more important as the frequency and severity of forest disturbances increase.

Study of the Precise Determination of Pipeline Geometries Using UAV Scanning Compared to Terrestrial Scanning, Aerial Scanning and UAV Photogrammetry.

Transmission pipelines belong to technical infrastructure, the condition of which is subject to periodic monitoring. The research was to verify whether aerial measurement methods, especially UAV laser scanning, could determine the geometric shape of pipelines with a precision similar to that of terrestrial scanning, adopted as a reference method. The test object was a section of a district heating pipeline with two types of surfaces: matte and glossy. The pipeline was measured using four methods: terrestrial scanning, airborne scanning, UAV scanning and the structure from motion method. Then, based on the reference terrestrial scanning data, pipeline models were created, with which all methods were compared. The comparison made it possible to find that only the UAV scanning yielded results consistent with those of the terrestrial scanning for all the pipes. The differences usually did not exceed 10 mm, sometimes reaching 20 mm. The structure from motion method yielded unstable results. For the old, matte pipes, the results were similar to those of the UAV scan; however, for the new, shiny pipes, the differences were up to 60 mm.

Automated Point Cloud Registration Approach Optimized for a Stop-and-Go Scanning System.

The latest advances in mobile platforms, such as robots, have enabled the automatic acquisition of full coverage point cloud data from large areas with terrestrial laser scanning. Despite this progress, the crucial post-processing step of registration, which aligns raw point cloud data from separate local coordinate systems into a unified coordinate system, still relies on manual intervention. To address this practical issue, this study presents an automated point cloud registration approach optimized for a stop-and-go scanning system based on a quadruped walking robot. The proposed approach comprises three main phases: perpendicular constrained wall-plane extraction; coarse registration with plane matching using point-to-point displacement calculation; and fine registration with horizontality constrained iterative closest point (ICP). Experimental results indicate that the proposed method successfully achieved automated registration with an accuracy of 0.044 m and a successful scan rate (SSR) of 100% within a time frame of 424.2 s with 18 sets of scan data acquired from the stop-and-go scanning system in a real-world indoor environment. Furthermore, it surpasses conventional approaches, ensuring reliable registration for point cloud pairs with low overlap in specific indoor environmental conditions.

LiDAR-Based Structural Health Monitoring: Applications in Civil Infrastructure Systems.

As innovative technologies emerge, extensive research has been undertaken to develop new structural health monitoring procedures. The current methods, involving on-site visual inspections, have proven to be costly, time-consuming, labor-intensive, and highly subjective for assessing the safety and integrity of civil infrastructures. Mobile and stationary LiDAR (Light Detection and Ranging) devices have significant potential for damage detection, as the scans provide detailed geometric information about the structures being evaluated. This paper reviews the recent developments for LiDAR-based structural health monitoring, in particular, for detecting cracks, deformation, defects, or changes to structures over time. In this regard, mobile laser scanning (MLS) and terrestrial laser scanning (TLS), specific to structural health monitoring, were reviewed for a wide range of civil infrastructure systems, including bridges, roads and pavements, tunnels and arch structures, post-disaster reconnaissance, historical and heritage structures, roofs, and retaining walls. Finally, the existing limitations and future research directions of LiDAR technology for structural health monitoring are discussed in detail.

As-Built Inventory and Deformation Analysis of a High Rockfill Dam under Construction with Terrestrial Laser Scanning.

The construction of large earth/rock fill dams, albeit its remarkable progress, still relies largely on past experiences. Therefore, a comprehensive yet dependable monitoring program is particularly beneficial for guiding the practice. However, conventional measurements can only produce limited discrete data. This paper exploits the potential of the terrestrial laser scanning (TLS) for an accurate inventory of as-built states of a concrete-faced rockfill dam under construction and for a full-field analysis of the 3D deformation pattern over its upstream face. For the former, a well-designed 3D geodetic system, with a particular consideration of the topography, promises a regulated acquisition of high-quality and blind-zone-free point cloud at field and also eases the cumbersome data registration process while maintaining its precision in house. For the latter, a problem-tailored processing pipeline is proposed for deformation extraction. Its core idea is to achieve a highly precise alignment of the point clouds with Iterative Closed Point algorithms from different epochs in datum areas that displays a featured, undeformed geometry at stable positions across epochs. Then, the alignment transformation matrix is applied to the point clouds of respective upstream face for each epoch, followed by pairwise comparisons of multiple adjusted point clouds for deformation evaluation. A processing pipeline is used to exploit the peal scene data redundancy of the GLQ dam acquired at six different epochs. Statistical analysis shows that satisfactory accuracy for deformation detection can be repeatably achieved, regardless of the scanner's positioning uncertainties. The obtained 3D deformation patterns are characterised by three different zones: practically undeformed, outward and inward deformed zones. Their evolutions comply well with real construction stages and unique 3D valley topography. Abundant deformation results highlight the potential of TLS combined with the proposed data processing pipeline for cost-efficient monitoring of huge infrastructures compared to conventional labor-intense measurements.

Contactless Deformation Monitoring of Bridges with Spatio-Temporal Resolution: Profile Scanning and Microwave Interferometry.

Against the background of an aging infrastructure, the condition assessment process of existing bridges is becoming an ever more challenging task for structural engineers. Short-term measurements and structural monitoring are valuable tools that can lead to a more accurate assessment of the remaining service life of structures. In this context, contactless sensors have great potential, as a wide range of applications can already be covered with relatively little effort and without having to interrupt traffic. In particular, profile scanning and microwave interferometry, have become increasingly important in the research field of bridge measurement and monitoring in recent years. In contrast to other contactless displacement sensors, both technologies enable a spatially distributed detection of absolute structural displacements. In addition, their high sampling rate enables the detection of the dynamic structural behaviour. This paper analyses the two sensor types in detail and discusses their advantages and disadvantages for the deformation monitoring of bridges. It focuses on a conceptual comparison between the two technologies and then discusses the main challenges related to their application in real-world structures in operation, highlighting the respective limitations of both sensors. The findings are illustrated with measurement results at a railway bridge in operation.

TLSLeAF: automatic leaf angle estimates from single-scan terrestrial laser scanning.

Leaf angle distribution (LAD) in forest canopies affects estimates of leaf area, light interception, and global-scale photosynthesis, but is often simplified to a single theoretical value. Here, we present TLSLeAF (Terrestrial Laser Scanning Leaf Angle Function), an automated open-source method of deriving LADs from terrestrial laser scanning. TLSLeAF produces canopy-scale leaf angle and LADs by relying on gridded laser scanning data. The approach increases processing speed, improves angle estimates, and requires minimal user input. Key features are automation, leaf-wood classification, beta parameter output, and implementation in R to increase accessibility for the ecology community. TLSLeAF precisely estimates leaf angle with minimal distance effects on angular estimates while rapidly producing LADs on a consumer-grade machine. We challenge the popular spherical LAD assumption, showing sensitivity to ecosystem type in plant area index and foliage profile estimates that translate to c. 25% and c. 11% increases in canopy net photosynthesis (c. 25%) and solar-induced chlorophyll fluorescence (c. 11%). TLSLeAF can now be applied to the vast catalog of laser scanning data already available from ecosystems around the globe. The ease of use will enable widespread adoption of the method outside of remote-sensing experts, allowing greater accessibility for addressing ecological hypotheses and large-scale ecosystem modeling efforts.

Do trees have constant branch divergence angles?

Many herbaceous plants feature remarkably regular arrangements of lateral organs along the central axis. These phyllotactic patterns are generated by a constant divergence angle between successive buds (or whorls thereof) that first appears at the shoot apircal meristem and is maintained across later ontogentic stages when it can be observed at the macroscopic scale. Do the branches along a tree trunk exhibit similar patterns? Here we use branch skeleton data derived from terrestrial laser scans to empirically estimate the distributions of the divergence angles between successive branches along the trunks of mature European beech, Norway spruce, and Scots pine trees. We find that rather than clustering around a particular value, species-specific branch divergence angles feature statistical properties characteristic of a uniform distribution. We hypothesise this to be the result of the stochasticity in bud development and branch shedding, and provide a rigorous mathematical proof that even when the divergence angle between successive lateral buds is constant, the observed distribution of branch divergence angles will approximate a uniform distribution if bud mortality and branch shedding rates are high.

A new method to estimate branch biomass from terrestrial laser scanning data by bridging tree structure models.

BACKGROUND AND AIMS: Branch biomass and other attributes are important for estimating the carbon budget of forest stands and characterizing crown structure. As destructive measuring is time-consuming and labour-intensive, terrestrial laser scanning (TLS) as a solution has been used to estimate branch biomass quickly and non-destructively. However, branch information extraction from TLS data alone is challenging due to occlusion and other defects, especially for estimating individual branch attributes in coniferous trees. METHODS: This study presents a method, entitled TSMtls, to estimate individual branch biomass non-destructively and accurately by combining tree structure models and TLS data. The TSMtls method constructs the stem-taper curve from TLS data, then uses tree structure models to determine the number, basal area and biomass of individual branches at whorl level. We estimated the tree structural model parameters from 122 destructively measured Scots pine (Pinus sylvestris) trees and tested the method on six Scots pine trees that were first TLS-scanned and later destructively measured. Additionally, we estimated the branch biomass using other TLS-based approaches for comparison. KEY RESULTS: Tree-level branch biomass estimates derived from TSMtls showed the best agreement with the destructive measurements [coefficient of variation of root mean square error (CV-RMSE) = 9.66 % and concordance correlation coefficient (CCC) = 0.99], outperforming the other TLS-based approaches (CV-RMSE 12.97-57.45 % and CCC 0.43-0.98 ). Whorl-level individual branch attributes estimates produced from TSMtls showed more accurate results than those produced from TLS data directly. CONCLUSIONS: The results showed that the TSMtls method proposed in this study holds promise for extension to more species and larger areas.

Integrating terrestrial laser scanning with functional-structural plant models to investigate ecological and evolutionary processes of forest communities.

BACKGROUND: Woody plants (trees and shrubs) play an important role in terrestrial ecosystems, but their size and longevity make them difficult subjects for traditional experiments. In the last 20 years functional-structural plant models (FSPMs) have evolved: they consider the interplay between plant modular structure, the immediate environment and internal functioning. However, computational constraints and data deficiency have long been limiting factors in a broader application of FSPMs, particularly at the scale of forest communities. Recently, terrestrial laser scanning (TLS), has emerged as an invaluable tool for capturing the 3-D structure of forest communities, thus opening up exciting opportunities to explore and predict forest dynamics with FSPMs. SCOPE: The potential synergies between TLS-derived data and FSPMs have yet to be fully explored. Here, we summarize recent developments in FSPM and TLS research, with a specific focus on woody plants. We then evaluate the emerging opportunities for applying FSPMs in an ecological and evolutionary context, in light of TLS-derived data, with particular consideration of the challenges posed by scaling up from individual trees to whole forests. Finally, we propose guidelines for incorporating TLS data into the FSPM workflow to encourage overlap of practice amongst researchers. CONCLUSIONS: We conclude that TLS is a feasible tool to help shift FSPMs from an individual-level modelling technique to a community-level one. The ability to scan multiple trees, of multiple species, in a short amount of time, is paramount to gathering the detailed structural information required for parameterizing FSPMs for forest communities. Conventional techniques, such as repeated manual forest surveys, have their limitations in explaining the driving mechanisms behind observed patterns in 3-D forest structure and dynamics. Therefore, other techniques are valuable to explore how forests might respond to environmental change. A robust synthesis between TLS and FSPMs provides the opportunity to virtually explore the spatial and temporal dynamics of forest communities.

Terrestrial laser scanning: a new standard of forest measuring and modelling?

BACKGROUND: Laser scanning technology has opened new horizons for the research of forest dynamics, because it provides a largely automated and non-destructive method to rapidly capture the structure of individual trees and entire forest stands at multiple spatial scales. The structural data themselves or in combination with additional remotely sensed data also provide information on the local physiological state of structures within trees. The capacity of new methods is facilitated by the ongoing development of automated processing tools that are designed to capture information from the point cloud data provided by the remote measurements. SCOPE: Terrestrial laser scanning (TLS), performed from the ground or from unmanned aerial vehicles, in particular, has potential to become a unifying measurement standard for forest research questions, because the equipment is flexible to use in the field and has the capacity to capture branch-level structural information at the forestplot or even forest scale. This issue of Annals of Botany includes selected papers that exemplify the current and potential uses of TLS, such as for examination of crown interactions between trees, growth dynamics of mixed stands, non-destructive characterization of urban trees, and enhancement of ecological and evolutionary models. The papers also present current challenges in the applicability of TLS methods and report recent developments in methods facilitating the use of TLS data for research purposes, including automatic processing chains and quantifying branch and above-ground biomass. In this article, we provide an overview of the current and anticipated future capacity of TLS and related methods in solving questions that utilize measurements and models of forests. CONCLUSIONS: Due to its measurement speed, TLS provides a method to effortlessly capture large amounts of detailed structural forest information, and consequent proxy data for tree and forest processes, at a far wider spatial scale than is feasible with manual measurements. Issues with measurement precision and occlusion of laser beams before they reach their target structures continue to reduce the accuracy of TLS data, but the limitations are counterweighted by the measurement speed that enables large sample sizes. The currently high time-cost of analysing TLS data, in turn, is likely to decrease through progress in automated processing methods. The developments point towards TLS becoming a new and widely accessible standard tool in forest measurement and modelling.

Forest above-ground volume assessments with terrestrial laser scanning: a ground-truth validation experiment in temperate, managed forests.

BACKGROUND AND AIMS: Quantifying the Earth's forest above-ground biomass (AGB) is indispensable for effective climate action and developing forest policy. Yet, current allometric scaling models (ASMs) to estimate AGB suffer several drawbacks related to model selection and uncertainties about calibration data traceability. Terrestrial laser scanning (TLS) offers a promising non-destructive alternative. Tree volume is reconstructed from TLS point clouds with quantitative structure models (QSMs) and converted to AGB with wood basic density. Earlier studies have found overall TLS-derived forest volume estimates to be accurate, but highlighted problems for reconstructing finer branches. Our objective was to evaluate TLS for estimating tree volumes by comparison with reference volumes and volumes from ASMs. METHODS: We quantified the woody volume of 65 trees in Belgium (from 77 to 2800 L; Pinus sylvestris, Fagus sylvatica, Larix decidua, and Fraxinus excelsior) with QSMs and destructive reference measurements. We tested a volume expansion factor (VEF) approach by multiplying the solid and merchantable volume from QSMs by literature VEF values. KEY RESULTS: Stem volume was reliably estimated with TLS. Total volume was overestimated by +21 % using original QSMs, by +9 % and -12 % using two sets of VEF-augmented QSMs, and by -7.3 % using best-available ASMs. The most accurate method differed per site, and the prediction errors for each method varied considerably between sites. CONCLUSIONS: VEF-augmented QSMs were only slightly better than original QSMs for estimating tree volume for common species in temperate forests. Despite satisfying estimates with ASMs, the model choice was a large source of uncertainty, and species-specific models did not always exist. Therefore, we advocate for further improving tree volume reconstructions with QSMs, especially for fine branches, instead of collecting more ground-truth data to calibrate VEF and allometric models. Promising developments such as improved co-registration and smarter filtering approaches are ongoing to further constrain volumetric errors in TLS-derived estimates.