Tailoring the Structural and Optical Properties of Cerium Oxide Nanoparticles Prepared by an Ecofriendly Green Route Using Plant Extracts.

The present study explores an environmentally friendly green approach to obtain cerium oxide nanoparticles via a biomediated route using Mellisa officinalis and Hypericum perforatum plant extracts as reducing agents. The as-prepared nanoparticles were studied for their structural and morphological characteristics using XRD diffractometry, scanning electron microscopy, Raman, fluorescence and electronic absorption spectra, and X-ray photoelectron spectroscopy (XPS). The XRD pattern has shown the centered fluorite crystal structure of cerium oxide nanoparticles with average crystallite size below 10 nm. These observations were in agreement with the STEM data. The cubic fluorite structure of the cerium oxide nanoparticles was confirmed by the vibrational mode around 462 cm-1 due to the Ce-08 unit. The optical band gap was estimated from UV-Vis reflectance spectra, which was found to decrease from 3.24 eV to 2.98 eV. A higher specific area was determined for the sample using M. officinalis aqueous extract. The EDX data indicated that only cerium and oxygen are present in the green synthesized nanoparticles.

Synthesis and Biological Properties of Fluorescent Strigolactone Mimics Derived from 1,8-Naphthalimide.

Strigolactones (SLs) have potential to be used in sustainable agriculture to mitigate various stresses that plants have to deal with. The natural SLs, as well as the synthetic analogs, are difficult to obtain in sufficient amounts for practical applications. At the same time, fluorescent SLs would be useful for the mechanistic understanding of their effects based on bio-imaging or spectroscopic techniques. In this study, new fluorescent SL mimics containing a substituted 1,8-naphthalimide ring system connected through an ether link to a bioactive furan-2-one moiety were prepared. The structural, spectroscopic, and biological activity of the new SL mimics on phytopathogens were investigated and compared with previously synthetized fluorescent SL mimics. The chemical group at the C-6 position of the naphthalimide ring influences the fluorescence parameters. All SL mimics showed effects similar to GR24 on phytopathogens, indicating their suitability for practical applications. The pattern of the biological activity depended on the fungal species, SL mimic and concentration, and hyphal order. This dependence is probably related to the specificity of each fungal receptor-SL mimic interaction, which will have to be analyzed in-depth. Based on the biological properties and spectroscopic particularities, one SL mimic could be a good candidate for microscopic and spectroscopic investigations.

Metal Oxide Nanostructures (MONs) as Photocatalysts for Ciprofloxacin Degradation.

In recent years, organic pollutants have become a global problem due to their negative impact on human health and the environment. Photocatalysis is one of the most promising methods for the removal of organic pollutants from wastewater, and oxide semiconductor materials have proven to be among the best in this regard. This paper presents the evolution of the development of metal oxide nanostructures (MONs) as photocatalysts for ciprofloxacin degradation. It begins with an overview of the role of these materials in photocatalysis; then, it discusses methods of obtaining them. Then, a detailed review of the most important oxide semiconductors (ZnO, TiO2, CuO, etc.) and alternatives for improving their photocatalytic performance is provided. Finally, a study of the degradation of ciprofloxacin in the presence of oxide semiconductor materials and the main factors affecting photocatalytic degradation is carried out. It is well known that antibiotics (in this case, ciprofloxacin) are toxic and non-biodegradable, which can pose a threat to the environment and human health. Antibiotic residues have several negative impacts, including antibiotic resistance and disruption of photosynthetic processes.

Phytomediated-Assisted Preparation of Cerium Oxide Nanoparticles Using Plant Extracts and Assessment of Their Structural and Optical Properties.

Cerium oxide nanoparticles were obtained using aqueous extracts of Chelidonium majus and Viscum album. X-ray diffractometry analysis confirmed the crystalline structure of the synthesized cerium oxide nanoparticles calcined at 600 °C. Scanning electron microscopy, UV-Vis reflectance and Raman spectroscopy, XPS, and fluorescence studies were utilized to interpret the morphological and optical properties of these nanoparticles. The STEM images revealed the spherical shape of the nanoparticles and that they were predominantly uniform in size. The optical band gap of our cerium nanoparticles was determined to be 3.3 and 3.0 eV from reflectance measurements using the Tauc plots. The nanoparticle sizes evaluated from the Raman band at 464 cm-1 due to the F2g mode of the cubic fluorite structure of cerium oxide are close to those determined from the XRD and STEM data. The fluorescence results showed emission bands at 425, 446, 467, and 480 nm. The electronic absorption spectra have exhibited an absorption band around 325 nm. The antioxidant potential of the cerium oxide nanoparticles was estimated by DPPH scavenging assay.

Investigating the Vibrational, Magnetic and Dielectric Properties, and Antioxidant Activity of Cerium Oxide Nanoparticles.

Dielectric, magnetic and Raman measurements of cerium oxide nanoparticles obtained by the precipitation method are discussed. Morphological study was performed by scanning electron microscopy, confirming the formation of nanoparticles of 5-27 nm. The Raman spectra exhibited a strong band around 465 cm-1, corresponding to the symmetrical stretching mode of the Ce-O8 vibrational unit. The nature of the room temperature ferromagnetism of cerium oxide nanoparticles was analyzed, taking into account the oxygen defects at the surface or interface of the nanoparticles. The evolution of dielectric constant, ε', and dielectric loss, ε″ was studied as a function of frequency at different temperatures. Additionally, the variation of the electric conductivity versus temperature was investigated. Finally, complex impedance study of the cerium oxide nanoparticles was performed.

Synthesis and Solvent Dependent Fluorescence of Some Piperidine-Substituted Naphthalimide Derivatives and Consequences for Water Sensing.

Novel fluorescent strigolactone derivatives that contain the piperidine-substituted 1,8-naphthalimide ring system connected through an ether link to a bioactive 3-methyl-furan-2-one unit were synthesized and their spectroscopic properties investigated. The solvatochromic behavior of these piperidine-naphthalimides was monitored in solvents of different polarity using the electronic absorption and fluorescence spectra. These compounds exhibited a strong positive solvatochromism taking into account the change of solvent polarity, and the response mechanism was analyzed by fluorescence lifetime measurements. According to Catalan and [f(n), f(ε), ß, α] solvent scales, the dipolarity and polarizability are relevant to describe the solute-solvent interactions. The emission chemosensing activity was discussed in order to determine the water content in organic environments. The emission intensity of these compounds decreased rapidly in dioxane, increasing water level up to 10%. Measuring of quantum yield indicated that the highest values of quantum efficiency were obtained in nonpolar solvents, while in polar solvents these derivatives revealed the lowest quantum yield. The fluorescence decay can be described by a monoexponential model for low water levels, and for higher water contents a biexponential model was valid.

On the Charge-Transfer Excitations in Azobenzene Maleimide Compounds: A Theoretical Study.

Photoswitchable systems with charge-transfer (CT) transitions have gained much attention during the recent years because of their many emerging applications. CT transitions themselves are of fundamental importance from physical, chemical, engineering, and molecular modeling points of view because they depend on the modified intramolecular electronic structure. CT transitions in azobenzene (AB) were observed when substituted with the maleimide (MI) functional group. This work represents a systematic theoretical study of excited states of the AB-MI structures of eight azo derivatives. In addition to the two main azo transitions (π → π* and n → π*), our calculations show a CT occurring between the azo moiety as a donor and the MI group as an acceptor. The CT mechanism can be characterized based on both the number and the position of the MI fragments. MI groups in the azo structure result in low-energy transitions, changing the order of the main transitions by introducing a CT character. Calculations using both density functional theory (DFT) and high-end molecular orbital theories confirm the CT character of these derivatives, although the order of excited states was found to differ depending on the chosen level of theory. We present here the first theoretical investigation of the electronic excited states (nπ*CT and ππ*CT) and corresponding transitions for this class of compounds. The computational results showed that the CT mechanism in AB-MI derivatives can occur via two pathways: planar and twisted. Our findings are expected to be of substantial interest, especially in the area of molecular optoelectronics and in the design of responsive materials.

Novel rare earth (RE-La, Er, Sm) metal doped ZnO photocatalysts for degradation of Congo-Red dye: Synthesis, characterization and kinetic studies.

Synthesis and characterization of novel ZnO:RE nanostructured materials doped with 1% rare-earth elements (RE = La, Er, Sm) and their testing for photocatalytic applications were reported. The materials were obtained via electrospining, followed by calcination at 700 °C. The samples were characterized in terms of surface morphology (SEM, TEM), crystalline structure (XRD) and band gap energies. TEM results showed the formation of a unidimensional structure (ZnO) with an average fiber diameter of 600 nm and a morphology consisting of interconnected nanoparticles having dimensions in the range 25-134 nm (ZnO doped with RE). Optical properties were explored by using UV-VIS reflectance spectra and the band gap values were determined with the Kubelka-Munk function (KM) by plotting [F(R∞)hν]2vs. hʋ. The photocatalytic activity was assessed by studying the degradation of a water-soluble anionic dye (Congo-Red) under UV-light irradiation. The data related to photodegradation kinetics were reasonably fitted to the pseudo-first-order kinetic model. Results revealed that the values of the rate constants ranged from 10-3 to 10-2 min-1, depending on the material type and initial dye concentration. In addition, Langmuir-Hinshelwood (LH) model was utilized to explain the kinetics of photodegradation reactions of CR in the presence of (ZnO:Sm) sample. The LH approach suggested that both adsorption and photocatalysis phenomena prevailed in the process of dye removal. Optimal conditions of experiments were determined empirically by employing the gradient method. Thus, a maximal value of color removal efficiency (95.8%) was observed experimentally for the initial dye concentration of 10.7 mg/L and 0.236 g/L catalyst dosage (ZnO:Sm). Furthermore, a successful recovery of the spent catalyst was accomplished by thermal activation.

Photophysical Properties of some 1,3,4-Oxadiazole Derivatives Containing Phenolphtalein, Fluorene and Bisphenol A Units.

The photophysical properties of the three 1,3,4-oxadiazole derivatives containing fluorene (Ox-FL); fluorene and phenolphtaleine (Ox-FL-FF); or fluorene and bisphenol A (Ox-FL-BPA) moieties in the main chain were investigated by the fluorescence and absorption spectroscopy in different solvents and in the solid state. The electronic absorption spectra included a strong absorption band located in the 270-395 nm region, with a maxima around at 302 nm. The fluorescence excitation spectra were also characterized by one broad band, appearing in the wavelength range of 220-340 nm. All samples displayed the emission bands around 356-373 nm and exhibit high quantum yields ranged from 31.61 to 90.77%, in chloroform solution. The sensitivity of the emission spectra on medium characteristics (polarity, acidity and basicity) were evaluated by using the Catalan solvent scale and the fluorescence titration with a dilute acid solution.

A New Pathway for the Synthesis of a New Class of Blue Fluorescent Benzofuran Derivatives.

In this study an efficient and straightforward method for obtaining a new class of blue fluorescent bezofuran derivatives, under microwave irradiation, as well as under conventional thermal heating, is presented. Under conventional TH the reactions occur selectively, and a single type of benzofuran ester derivative was obtained. The synthesis under MW irradiation also led to benzofuran derivatives, but in a time-dependent manner. Irradiation for a short period of time led to a mixture of two types of benzofuran derivatives (3a⁻c and 4a⁻c), while MW irradiation for a longer period of time led to a single type of benzofuran (3-methylbenzofuran), the reaction becoming highly selective. Taking into consideration the advantages offered by MW irradiation in terms of a substantial decrease of solvent consumed, a substantial reduction in reaction time (from days to hours), and a consequent diminution in energy consumption, these methods could be considered environmentally friendly. Here, feasible reaction mechanisms for the benzofuran derivatives formation are described. The absorption and fluorescence emission of the obtained benzofuran derivatives were studied, with part of these compounds being intense blue emitters. A certain influence of the benzofuran substituents concerning absorption and fluorescent properties was observed. Only compounds anchored with a carbomethoxy group of furan ring have shown good quantum yields.

1,3,4-Oxadiazole Derivatives. Optical Properties in Pure and Mixed Solvents.

1,3,4-Oxadiazole derivatives-organic materials are an interesting and continuously developing area of research. This review describes some optical properties and highlights the current applications of these compounds in biomedical and optoelectronic fields. The relationships between polymer structures, environmental factors and optical properties (absorption and fluorescence) of several selected and relevant l,3,4-oxadiazole-containing molecules were presented in this review. These aspects were analyzed in various pure solvents and microheterogeneous media (mixed solvents). Also, the selectivity and sensitivity of some 1,3,4-oxadiazole derivatives-organic materials for different metal ions were discussed and evaluated by using spectral techniques. Finally, some important photophysical characteristics of 34 series of organic materials containing -1,3,4-oxadiazole rings, were collected in a table.

Optical Properties of Some Fluorinated Poly(1,3,4-Oxadiazole-Ether)s in Homogeneous and Heterogeneous Media. Changes Induced by SnO2, NiO and SnO2/NiO Mixed-Oxide Nanoparticles.

Optical characteristics of some fluorinated poly(1,3,4-oxadiazole-ether)s in presence of SnO2, NiO and SnO2/NiO mixed-oxide nanoparticles (NPs) was investigated. The interactions between polymers and metal oxide NPs were studied by steady-state UV-Vis absorption and fluorescence spectroscopy techniques. The absorption and fluorescence signals of all investigated polymers was modified by presence of both pure and mixed-oxide nanoparticles. The moderate values of Stern-Volmer quenching constant and non-linear trend of Scott plot indicate the less affinity between metal oxide NPs and polymers. The solvation behavior of some fluorinated poly(1,3,4-oxadiazole-ether)s in chloroform-N,N-dimethylformamide and N,N-dimethylformamide-dimethylsulfoxide mixtures was discussed.

Fluorescence Modulation and Photochromism in Azobismaleimide Derivatives.

A fluorophore-photochrome system incorporating an aryleneimine type fluorophore and an azobismaleimide photochrome was developed and the photochemical properties of this system were investigated. The photoisomerization of trans-azoaromatic chromophore leads to the increase of the fluorescence intensity of fluorophore. The cis azobismaleimide isomers revert photochemically to the trans form and the emission intensity decreases. The fluorescence intensity of the imine fluorophore can be modulated under irradiation with UV and visible (436 nm) light due to reversible trans-cis-trans photoisomerization of azobismaleimide partner. The photoisomerization kinetics was obeyed a first-order relationship with a rate constant of 1.95 × 10(-2) s(-1) for azobismaleimide/imine fluorophore system and for polyazothioetherimide/imine derivative the kinetics was described by a biexponential equation.

The effect of permodified cyclodextrins encapsulation on the photophysical properties of a polyfluorene with randomly distributed electron-donor and rotaxane electron-acceptor units.

We report on the synthesis as well as the optical, electrochemical and morphological properties of two polyrotaxanes (4a and 4b), which consist of electron-accepting 9,9-dicyanomethylenefluorene 1 as an inclusion complex in persilylated ß- or γ-cyclodextrin (TMS-ß-CD, TMS-γ-CD) (1a, 1b) and methyltriphenylamine as an electron-donating molecule. They are statistically distributed into the conjugated chains of 9,9-dioctylfluorene 3 and compared with those of the corresponding non-rotaxane 4 counterpart. Rotaxane formation results in improvements of the solubility, the thermal stability, and the photophysical properties. Polyrotaxanes 4a and 4b exhibited slightly red-shifted absorption bands with respect to the non-rotaxane 4 counterpart. The fluorescence lifetimes of polyrotaxanes follow a mono-exponential decay with a value of τ = 1.14 ns compared with the non-rotaxane, where a bi-exponential decay composed of a main component with a relative short time of τ1 = 0.88 (57.08%) and a minor component with a longer lifetime of τ2 = 1.56 ns (42.92%) were determined. The optical and electrochemical band gaps (ΔE g) as well as the ionization potential and electronic affinity characterized by smaller values compared to the values of any of the constituents. AFM reveals that the film surface of 4a and 4b displays a granular morphology with a lower dispersity supported by a smaller roughness exponent compared with the non-rotaxane counterpart.

Structural, Optical and Dielectric Properties of Some Nanocomposites Derived from Copper Oxide Nanoparticles Embedded in Poly(vinylpyrrolidone) Matrix.

Polymer nanocomposite films based on poly(vinyl pyrrolidone) incorporated with different amounts of copper oxide (CuO) nanoparticles were prepared by the solution casting technique. The PVP/CuO nanocomposites were analyzed by X-ray diffractometry (XRD), scanning electron microscopy, UV-Visible absorption spectroscopy and dielectric spectroscopy. The XRD analysis showed that the monoclinic structure of cupric oxide was maintained in the PVP host matrix. The key optical parameters, such as optical energy gap Eg, Urbach energy EU, absorption coefficient and refractive index, were estimated based on the UV-Vis data. The optical characteristics of the nanocomposite films revealed that their transmittance and absorption were influenced by the addition of CuO nanoparticles in the PVP matrix. Incorporation of CuO nanoparticles into the PVP matrix led to a significant decrease in band gap energy and an increase in the refractive index. The dielectric and electrical behaviors of the PVP/CuO nanocomposites were analyzed over a frequency range between 10 Hz and 1 MHz. The effect of CuO loading on the dielectric parameters (dielectric constant and dielectric loss) of the metal oxide nanocomposites was also discussed.

Mechanical Properties and Equilibrium Swelling Characteristics of Some Polymer Composites Based on Ethylene Propylene Diene Terpolymer (EPDM) Reinforced with Hemp Fibers.

EPDM/hemp fiber composites with fiber loading of 0-20 phr were prepared by the blending technique on a laboratory electrically heated roller mill. Test specimens were obtained by vulcanization using a laboratory hydraulic press. The elastomer crosslinking and the chemical modification of the hemp fiber surface were achieved by a radical reaction mechanism initiated by di(tert-butylperoxyisopropyl)benzene. The influence of the fiber loading on the mechanical properties, gel fraction, swelling ratio and crosslink degree was investigated. The gel fraction, crosslink density and rubber-hemp fiber interaction were evaluated based on equilibrium solvent-swelling measurements using the Flory-Rehner relation and Kraus and Lorenz-Park equations. The morphology of the EPDM/hemp fiber composites was analyzed by scanning electron microscopy. The water absorption increases as the hemp fiber loading increases.

Optical properties of some new azo photoisomerizable bismaleimide derivatives.

Novel polythioetherimides bearing azobenzene moieties were synthesized from azobismaleimides and bis-2-mercaptoethylether. Kinetics of trans-cis photoisomerization and of thermal conversion of cis to trans isomeric forms were investigated in both polymer solution and poly(methyl methacrylate) doped films using electronic absorption spectroscopy. Thermal recovery kinetics is well described by a two-exponential relation both in solution and polymer matrix, while that of low molecular weight azobismaleimide fit a first-order equation. The photoinduced cis-trans isomerization by visible light of azobenzene chromophores was examined in solution and in polymer films. The rate of photoinduced recovery was very high for azobismaleimides.

Revealing the Effect of Synthesis Conditions on the Structural, Optical, and Antibacterial Properties of Cerium Oxide Nanoparticles.

Cerium oxide nanoparticles were prepared by a precipitation method using Ce(IV) sulphate as precursor dispersed in glycerol with varying synthesis parameters such as temperature or precipitating agent. The structural and morphological characteristics of the obtained nanoparticles were investigated by X-ray diffraction, transmission electron microscopy, and diffuse reflectance spectroscopy. The crystallite size of the nanoparticles varied between 13 and 17 nm. The presence of Ce3+ and Ce4+ was proved by XPS data in the CeO2 samples and the conservation of the fluorite structure was evinced by X-ray diffractograms with a contraction of the lattice parameter, regardless of the size of the nanoparticle. From diffuse reflectance spectra, two band gap energy values for the direct transition were observed. Depending on the synthesis condition, the red shift of gap energy and the blue shift of Urbach energy with increasing content of Ce3+ were ascertained. The antibacterial tests revealed that the cerium oxide nanoparticles show good antimicrobial activity towards the common pathogens Escherichia coli and Staphylococcus aureus.

Dielectric, Thermal and Water Absorption Properties of Some EPDM/Flax Fiber Composites.

This paper deals with the dielectric and sorption properties of some flax fiber-reinforced ethylene-propylene-diene monomer (EPDM) composites containing different fiber loadings as well as their behavior after exposure to different doses of electron beam irradiation. Three relaxation processes were evinced, a weak relaxation ß at sub-Tg temperatures and two α-type relaxations above the Tg. The EPDM/flax composites exhibited higher values of dielectric constant, dielectric loss and conductivity as compared to a pristine EPDM sample. Using thermogravimetric analysis (TG) coupled with Fourier transform infrared spectroscopy (FTIR) and mass spectrometry (MS) (TG/FTIR/MS system), the degradation products can be identified. The water uptake increased as the flax fiber level increased in composites. The water uptake tests of irradiated composites showed that the highest water content was obtained for a flax fiber level of 20 phr.

Innovative Low-Cost Carbon/ZnO Hybrid Materials with Enhanced Photocatalytic Activity towards Organic Pollutant Dyes' Removal.

A new type of material based on carbon/ZnO nanostructures that possesses both adsorption and photocatalytic properties was obtained in three stages: cellulose acetate butyrate (CAB) microfiber mats prepared by the electrospinning method, ZnO nanostructures growth by dipping and hydrothermal methods, and finally thermal calcination at 600 °C in N2 for 30 min. X-ray diffraction (XRD) confirmed the structural characteristics. It was found that ZnO possesses a hexagonal wurtzite crystalline structure. The ZnO nanocrystals with star-like and nanorod shapes were evidenced by scanning electron microscopy (SEM) measurements. A significant decrease in Eg value was found for carbon/ZnO hybrid materials (2.51 eV) as compared to ZnO nanostructures (3.21 eV). The photocatalytic activity was evaluated by studying the degradation of three dyes, Methylene Blue (MB), Rhodamine B (RhB) and Congo Red (CR) under visible-light irradiation. Therefore, the maximum color removal efficiency (both adsorption and photocatalytic processes) was: 97.97% of MB (C0 = 10 mg/L), 98.34% of RhB (C0 = 5 mg/L), and 91.93% of CR (C0 = 10 mg/L). Moreover, the value of the rate constant (k) was found to be 0.29 × 10-2 min-1. The novelty of this study relies on obtaining new photocatalysts based on carbon/ZnO using cheap and accessible raw materials, and low-cost preparation techniques.