A review on the use of lignocellulosic materials for arsenic adsorption.

In this review, bibliometric analysis was made of recent studies and current trends concerning the application of lignocellulosic materials as bioadsorbents for the removal of arsenic from aqueous systems. Evaluation was made of lignocellulosic adsorbents and their chemical characteristics, as well as interactions involved in the adsorption of arsenic, bioadsorbent reusage (desorption and re-adsorption), competition between co-existing ions in multi-element aqueous solutions, and applications of bioadsorbents in batch and continuous systems. Lignocellulosic biomass has been shown to be a promising source of new adsorbents, since it is a low-cost and renewable material. However, there seems to be no commercially available technology that uses bioadsorbents based on lignocellulosic biomass for arsenic removal. In addition, the structural modification of lignocellulosic biomass to improve its adsorption capacity and selectivity has proved to be a suitable strategy, with the service time and the selectivity of the bioadsorbent in the presence of co-existing ions the most critical aspects to be pursued. The competitive adsorption of co-existing anions (PO43-, SO42-, NO3-, and Cl-) by the adsorption sites, as well as life-cycle assessment and cost analysis are rarely reported. Complexation, electrostatic attraction, ion exchange and precipitation were the main interactions involved in the adsorption of arsenic on lignocellulosic materials. However, most studies have failed to prove the nature of the interactions. Macroscopic methods can be useful to evaluate the adsorption mechanism of arsenic on bioadsorbents of complex structure, such as lignocellulosic biomass (modified or not). Nevertheless, the elucidation of the adsorption mechanism requires experiments based on measurements at the microscopic level. The upscaling of biosorption technology for arsenic removal will only be possible through studies that investigate: i) the interactions involved in the adsorption process; ii) the transfer of bench-scale experiments to pilot-scale experiments with real contaminated water with low arsenic concentration; and iii) the life-cycle assessment of biosorbents produced from lignocellulosic biomass.

Application of pyridine-modified chitosan derivative for simultaneous adsorption of Cu(II) and oxyanions of Cr(VI) from aqueous solution.

The bioadsorbent C1, which is a chitosan derivative prepared in a one-step synthesis, was successfully used to adsorb Cr(VI) and Cu(II) simultaneously. Here, for the first time the simultaneous adsorption of a cation and an anion was modeled using the Corsel model for kinetics and the Real Adsorbed Solution Theory model for equilibrium data. Batch studies of the adsorption of Cu(II) and Cr(VI) in single and binary aqueous solutions were performed as a function of initial solute concentration, contact time, and solution pH. The maximum adsorption capacities of C1 in single and binary aqueous solutions were 1.84 and 1.13 mmol g-1 for Cu(II) and 3.86 and 0.98 mmol g-1 for Cr(VI), respectively. The reuse of C1 was investigated, with Cu(II) ions being almost completely desorbed and fully re-adsorbed. For Cr(VI), the desorption was incomplete resulting in a lower re-adsorption. Energy-dispersive X-ray spectroscopy was used for mapping the distributions of Cr(VI) and Cu(II) adsorbed on the C1 surface in single and binary adsorption systems. Isothermal titration calorimetry experiments were performed for Cr(VI) and Cu(II) adsorption in single solutions. The thermodynamic parameters of adsorption showed that the adsorption of both metal ions was enthalpically driven, but entropically unfavorable.

Use of a new zwitterionic cellulose derivative for removal of crystal violet and orange II from aqueous solutions.

This study describes the synthesis of a new bioadsorbent with zwitterionic characteristics and its successful application for removal of a cationic dye (crystal violet, CV) and an anionic dye (orange II, OII) from single component aqueous systems. The new bi-functionalized cellulose derivative (MC3) was produced by chemical modification of cellulose with succinic anhydride and choline chloride to introduce carboxylic and quaternary ammonium functional groups on the cellulose surface. MC3 was characterized by several wet chemical and spectroscopic methods. The effects of solution pH, contact time, and initial solute concentration on removal of CV and OII by MC3 were investigated. Studies of the desorption and re-adsorption of the dyes were also carried out. The isotherms for adsorption of CV and OII on MC3 were satisfactorily fitted using the Konda and Langmuir models. MC3 showed experimental maximum adsorption capacities of 2403 mg g-1 for CV and 201 mg g-1 for OII. The desorption and re-adsorption results showed that MC3 could be reused in successive adsorption cycles, which is essential for minimizing process costs and waste generation. The findings showed that MC3 is a versatile biosorbent capable of efficiently removing both cationic and anionic dyes.