Dimensional Regulation from 1D/3D to 2D/3D of Perovskite Interfaces for Stable Inverted Perovskite Solar Cells.

Constructing low-dimensional/three-dimensional (LD/3D) perovskite solar cells can improve efficiency and stability. However, the design and selection of LD perovskite capping materials are incredibly scarce for inverted perovskite solar cells (PSCs) because LD perovskite capping layers often favor hole extraction and impede electron extraction. Here, we develop a facile and effective strategy to modify the perovskite surface by passivating the surface defects and modulating surface electrical properties by incorporating morpholine hydriodide (MORI) and thiomorpholine hydriodide (SMORI) on the perovskite surface. Compared with the PI treatment that we previously developed, the one-dimensional (1D) perovskite capping layer derived from PI is transformed into a two-dimensional (2D) perovskite capping layer (with MORI or SMORI), achieving dimension regulation. It is shown that the 2D SMORI perovskite capping layer induces more robust surface passivation and stronger n-N homotype 2D/3D heterojunctions, achieving a p-i-n inverted solar cell with an efficiency of 24.55%, which retains 87.6% of its initial efficiency after 1500 h of operation at the maximum power point (MPP). Furthermore, 5 × 5 cm2 perovskite mini-modules are presented, achieving an active-area efficiency of 22.28%. In addition, the quantum well structure in the 2D perovskite capping layer increases the moisture resistance, suppresses ion migration, and improves PSCs' structural and environmental stability.

Multifunctional Buffer Layer Engineering for Efficient and Stable Wide-Bandgap Perovskite and Perovskite/Silicon Tandem Solar Cells.

Inverted perovskite solar cells (PSCs) are preferred for tandem applications due to their superior compatibility with diverse bottom solar cells. However, the solution processing and low formation energy of perovskites inevitably lead to numerous defects at both the bulk and interfaces. We report a facile and effective strategy for precisely modulating the perovskite by incorporating AlOx deposited by atomic layer deposition (ALD) on the top interface. We find that Al3+ can not only infiltrate the bulk phase and interact with halide ions to suppress ion migration and phase separation but also regulate the arrangement of energy levels and passivate defects on the perovskite surface and grain boundaries. Additionally, ALD-AlOx exhibits an encapsulation effect through a dense interlayer. Consequently, the ALD-AlOx treatment can significantly improve the power conversion efficiency (PCE) to 21.80 % for 1.66 electron volt (eV) PSCs. A monolithic perovskite-silicon TSCs using AlOx-modified perovskite achieved a PCE of 28.5 % with excellent photothermal stability. More importantly, the resulting 1.55 eV PSC and module achieved a PCE of 25.08 % (0.04 cm2) and 21.01 % (aperture area of 15.5 cm2), respectively. Our study provides an effective way to efficient and stable wide-band gap perovskite for perovskite-silicon TSCs and paves the way for large-area inverted PSCs.

Deciphering the Roles of MA-Based Volatile Additives for α-FAPbI3 to Enable Efficient Inverted Perovskite Solar Cells.

Functional additives that can interact with the perovskite precursors to form the intermediate phase have been proven essential in obtaining uniform and stable α-FAPbI3 films. Among them, Cl-based volatile additives are the most prevalent in the literature. However, their exact role is still unclear, especially in inverted perovskite solar cells (PSCs). In this work, we have systematically studied the functions of Cl-based volatile additives and MA-based additives in formamidinium lead iodide (FAPbI3)-based inverted PSCs. Using in situ photoluminescence, we provide clear evidence to unravel the different roles of volatile additives (NH4Cl, FACl, and MACl) and MA-based additives (MACl, MABr, and MAI) in the nucleation, crystallization, and phase transition of FAPbI3. Three different kinds of crystallization routes are proposed based on the above additives. The non-MA volatile additives (NH4Cl and FACl) were found to promote crystallization and lower the phase-transition temperatures. The MA-based additives could quickly induce MA-rich nuclei to form pure α-phase FAPbI3 and dramatically reduce phase-transition temperatures. Furthermore, volatile MACl provides a unique effect on promoting the growth of secondary crystallization during annealing. The optimized solar cells with MACl can achieve an efficiency of 23.1%, which is the highest in inverted FAPbI3-based PSCs.

Two-Dimensional Silver(I)-Dithiocarboxylate Coordination Polymer Exhibiting Strong Near-Infrared Photothermal Effect.

Materials that demonstrate near-infrared (NIR) absorption and can simultaneously convert the electromagnetic irradiation into heat are promising for photothermal therapy. Traditionally, such a material is either pure inorganic, such as CuS, Ag2S, and carbon nanotube, or pure organic, such as polyaniline, polypyrrole, and conjugated polymers. Here we show that strong NIR photothermal effect can also be achieved in inorganic-organic hybrid coordination polymers (CPs) or metal-organic frameworks (MOFs). Our strategy is to construct CPs with inorganic Ag-S components that are interlinked by the organic ligands into a higher-dimensional hybrid network. Interestingly, the two resulting CPs, [Ag(Py-4-CSS)] n 1 and [Ag2(Py-4-CSS)(Py-4-CSSS)] n 2 (Py-4-CSS = pyridine-4-dithiocarboxylate; Py-4-CSSS = pyridine-4-perthiocarboxylate), show disparate structures due to the varied coordination mode of the pyridine group. For 1, the N atom coordinates to the Ag+ center and forms a two-dimensional square framework, while for 2, such a Ag-N bond is disconnected and forms only a one-dimensional structure. Interestingly, this difference leads to the distinct absorption properties in the NIR region. Under 800 nm radiation, the temperature of 1 can rise up to 24.5 °C in 3 min with photothermal conversion efficiency of 22.1%, which is about 2× that of pure inorganic Ag2S material and among the highest compared to various known inorganic materials, for example, Au nanoshells (13%), nanorods (21%), and Cu2- xSe nanocrystals (22%) irradiated with 800 nm light, while for 2, the NIR absorption is absent. This result first demonstrates that the inorganic-organic hybrid approach can be applied to construct superior NIR photothermal materials, but the control of the structure is vital. Here the coordinating nitrogen atoms in 1 are conceived to be critical in promoting the charge transfer between the dithiocarboxylate ligands. To elucidate the response to NIR irradiation of 1, we measured the heat capacity and dielectric constant of 1 and also performed density functional theory calculations. Significantly, the large dielectric constant and flat energy bands indicates 1 is much easier to be polarized and has a high electron effective mass. Thus, unlike the pure inorganic material, such as Ag2S, in which electron and hole can quantum mechanically combine to give off light, the joint-force of organic ligands in 1 effectively enhances polaronic recombination into heat.

Dynamic Hybrid Models With Active Sampling and Adaptive Selection of Double-Domain Features for the Tuning of Microwave Cavity Filters.

Microwave cavity filters are essential electromechanical coupling devices in communication systems. Structural-parameter tuning by experienced operators improves the filter performance but is demanding and time-consuming. The automatic tuning method has received extensive research attentions using data-driven modeling approaches. However, two main issues affect the accuracy and efficiency of the model construction: 1) features of tuning processes, as model inputs, have limited adaptability and extraction accuracy to different resonant states and 2) models require plentiful training data and the training process is time-consuming. Thus, dynamic hybrid models are developed in this study with self-selected inputs, self-organized samples, and a self-learning structure. First, spatial features are extracted to flexibly depict the tuning characteristic, and double-domain (spatial or circuital) features are selected adaptively to accommodate distinct resonance states. Second, a trustworthiness-curiosity-driven active sampling method is exploited to attain fewer and better-training data. Third, an improved glsms broad learning system acrlong BLS is developed using new modules of incremental node calculation and weight pruning, characterized by more lightweight and flexible structures. The proposed method is effective and flexible demonstrated by simulations and experiments, and the tuning task of microwave cavity filters is fulfilled in a more accurate and efficient manner.

Polyoxometalate Reinforced Perovskite Phase for High-Performance Perovskite Photovoltaics.

Ionic hybrid perovskites face challenges in maintaining their structural stability against non-equilibrium phase degradation, therefore, it is essential to develop effective ways to reinforce their corner-shared [PbI6]4- octahedral units. To strengthen structural stability, redox-active functional polyoxometalates (POMs) are developed and incorporated into perovskite solar cells (PSCs) to form a robust polyoxometalates/perovskite interlayer for stabilizing the perovskite phase. This approach offers several advantages: 1) promotes the formation of an interfacial connecting layer to passivate interfacial defects in addition to stabilize the [PbI6]4- units through exchanged ammonium cations in POMs with perovskites; 2) facilitates continuous structural repairing of Pb0- and I0-rich defects in the [PbI6]4- unit through redox electron shuttling of the electroactive metal ions in POMs; 3) provides guidance for selecting suitable redox mediators based on the kinetic studies of POM's effectiveness in reacting with targeted defects. The POM-reinforced device maintains 97.2% of its initial PCE after 1500 h of shelf-life test at 65 °C, while also enhancing the long-term operational stability. Additionally, this approach can be generally applicable across scalable sizes and various bandgap perovskites in devices, showing the promise of using functional POMs to enhance perovskite photovoltaic performance.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation.

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells. The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs. In this work, we adopted a solid-liquid two-step film formation technique, which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films. This method possesses the advantages of integrating vapor deposition and solution methods, which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform, large-area perovskite film. Furthermore, modification of the NiOx/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization. As a result, a large-area perovskite film possessing larger grains, fewer pinholes, and reduced defects could be achieved. The inverted PSM with an active area of 61.56 cm2 (10 × 10 cm2 substrate) achieved a champion power conversion efficiency of 20.56% and significantly improved stability. This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Two-dimensional semiconducting Cu(I)/Sb(III) bimetallic hybrid iodides with a double perovskite structure and photocurrent response.

Stable lead-free hybrid halide double perovskites have sparked widespread interest as a new kind of photoelectric material. Herein, for the first time, we successfully incorporated copper(I) and antimony(III) into two two-dimensional (2D) hybrid bimetallic double perovskite iodides, namely (NH3C6H11)4CuSbI8·H2O (CuSbI-1) and (NH3C6H10NH3)2CuSbI8·0.5H2O (CuSbI-2), using cyclohexylamine and 1,4-cyclohexanediamine as organic components. The band gaps for CuSbI-1 and CuSbI-2 were determined to be 2.22(2) eV and 2.21(2) eV, respectively. Furthermore, these two layered perovskites were readily dissolved in an organic solvent (1 mL DMF can dissolve 1 g sample for each compound) and could form smooth, pinhole-free, and uniform thin films through a facile spin-coating method. Photocurrent experiments with xenon lamp irradiation revealed the obvious photoelectric responses for both 2D double perovskites. The ratio of the photocurrent to the dark current (Ilight/Idark) for CuSbI-1 and CuSbI-2 is about 23 and 10, respectively, further suggesting their potential to be applied as light harvesters or light detectors. More importantly, these 2D double perovskite iodides show high moisture and thermal stabilities, indicating their potential for optoelectronic applications.

Compact Hole-Selective Self-Assembled Monolayers Enabled by Disassembling Micelles in Solution for Efficient Perovskite Solar Cells.

Self-assembled monolayers (SAMs) are widely employed as effective hole-selective layers (HSLs) in inverted perovskite solar cells (PSCs). However, most SAM molecules are amphiphilic in nature and tend to form micelles in the commonly used alcoholic processing solvents. This introduces an extra energetic barrier to disassemble the micelles during the binding of SAM molecules on the substrate surface, limiting the formation of a compact SAM. To alleviate this problem for achieving optimal SAM growth, a co-solvent strategy to disassemble the micelles of carbazole-based SAM molecules in the processing solution is developed. This effectively increases the critical micelle concentration to be above the processing concentration and enhances the reactivity of the phosphonic acid anchoring group to allow densely packed SAMs to be formed on indium tin oxide. Consequently, the PSCs derived from using MeO-2PACz, 2PACz, and CbzNaph SAM HSLs show universally improved performance, with the CbzNaph SAM-derived device achieving a champion efficiency of 24.98% and improved stability.

Unlocking the Ambient Temperature Effect on FA-Based Perovskites Crystallization by In Situ Optical Method.

Multiple cation-composited perovskites are demonstrated as a promising approach to improving the performance and stability of perovskite solar cells (PSCs). However, recipes developed for fabricating high-performance perovskites in laboratories are always not transferable in large-scale production, as perovskite crystallization is highly sensitive to processing conditions. Here, using an in situ optical method, the ambient temperature effect on the crystallization process in multiple cation-composited perovskites is investigated. It is found that the typical solvent-coordinated intermediate phase in methylammonium lead iodide (MAPbI3 ) is absent in formamidinium lead iodide (FAPbI3 ), and nucleation is almost completed in FAPbI3 right after spin-coating. Interestingly, it is found that there is noticeable nuclei aggregation in Formamidinium (FA)-based perovskites even during the spin-coating process, which is usually only observed during the annealing in MAPbI3 . Such aggregation is further promoted at a higher ambient temperature or in higher FA content. Instead of the general belief of stress release-induced crack formation, it is proposed that the origin of the cracks in FA-based perovskites is due to the aggregation-induced solute depletion effect. This work reveals the limiting factors for achieving high-quality FA-based perovskite films and helps to unlock the existing narrow processing window for future large-scale production.

Target Therapy for Buried Interface Enables Stable Perovskite Solar Cells with 25.05% Efficiency.

The buried interface in perovskite solar cells (PSCs) is pivotal for achieving high efficiency and stability. However, it is challenging to study and optimize the buried interface due to its non-exposed feature. Here, a facile and effective strategy is developed to modify the SnO2 /perovskite buried interface by passivating the buried defects in perovskite and modulating carrier dynamics via incorporating formamidine oxalate (FOA) in SnO2 nanoparticles. Both formamidinium and oxalate ions show a longitudinal gradient distribution in the SnO2 layer, mainly accumulating at the SnO2 /perovskite buried interface, which enables high-quality upper perovskite films, minimized defects, superior interface contacts, and matched energy levels between perovskite and SnO2 . Significantly, FOA can simultaneously reduce the oxygen vacancies and tin interstitial defects on the SnO2 surface and the FA+ /Pb2+ associated defects at the perovskite buried interface. Consequently, the FOA treatment significantly improves the efficiency of the PSCs from 22.40% to 25.05% and their storage- and photo-stability. This method provides an effective target therapy of buried interface in PSCs to achieve very high efficiency and stability.

Rigid Amine-Induced Pseudo-3 D Lead-Free Bismuth Halide Perovskite with an Improved Band Edge for Visible-Light Absorption.

Bismuth organometal halide perovskites have recently been investigated as potential substitutes for lead perovskite solar-cell absorbers because of their lower toxicity. However, the narrowing of the band gap remains a crucial challenge for their practical application. All known Bi-based perovskites have large band gaps, thereby affording weak visible-light absorption. This study concerns a novel, lead-free, pseudo-3 D perovskite optoelectronic material, (MV)BiI5 (MV2+ =methyl viologen). The pseudo-3 D metal-halogen perovskite-like structure is constructed by connecting [BiI5 ] 2+ units via I⋅⋅⋅I contacts. MV, as a rigid organic amine, is located at the center of each parallelepiped to balance the charge and stabilize the structure. (MV)BiI5 has a narrow band gap of 1.48 eV and a better photoresponse than (MV)BiCl5 with a 1 D structure. (MV)BiI5 is the first Bi-based perovskite compound with a band gap energy comparable with (CH3 NH3 )PbI3 , which is encouraging for optoelectronic applications. This research will open a potential pathway for the design of pseudo-3 D Bi-based perovskites with performances comparable with APbX3 absorbers.