Aviation fuel based on wastewater-grown microalgae: Challenges and opportunities of hydrothermal liquefaction and hydrotreatment.

The current technical issues related to the conversion of algal biomass into aviation biofuel through hydrothermal liquefaction (HTL) and the upgrading of bio-oil through hydrotreatment have been reviewed and consolidated. HTL is a promising route for converting microalgae into sustainable aviation fuel (SAF). However, HTL must be followed by the hydrotreatment of bio-oil to ensure that its composition and properties are compatible with SAF standards. The fact that microalgae offer the possibility of recovering wastewater treatment resources not only makes them more attractive but also serves as an incentive for wastewater treatment, especially in countries where this service has not been universalized. The combination of SAF and wastewater treatment aligns with the Sustainable Development Goals of the United Nations, representing an advantageous opportunity for both aviation and sanitation. In this context, the utilization of HTL by-products in the concept of a biorefinery is essential for the sustainability of aviation biofuel production through this route. Another important aspect is the recovery and reuse of catalysts, which are generally heterogeneous, allowing for recycling. Additionally, discussions have focused on biomass pretreatment methods, the use of solvents and catalysts in HTL and hydrotreatment reactions, and the operational parameters of both processes. All these issues present opportunities to enhance the quantity and quality of bio-oil and aviation biofuel.

Enhancing environmental performance in biogas production from wastewater-grown microalgae: A life cycle assessment perspective.

The production of biogas from microalgae has gained attention due to their rapid growth, CO2 sequestration, and minimal land use. This study uses life cycle assessment to assess the environmental impacts of biogas production from wastewater-grown microalgae through anaerobic digestion within an optimized microalgae-based system. Using SimaPro® 9 software, 3 scenarios were modeled considering the ReCiPe v1.13 midpoint and endpoint methods for environmental impact assessment in different categories. In the baseline scenario (S1), a hypothetical system for biogas production was considered, consisting of a high rate algal pond (HRAP), a settling, an anaerobic digester, and a biogas upgrading unit. The second scenario (S2) included strategies to enhance biogas yield, namely co-digestion and thermal pre-treatment. The third scenario (S3), besides considering the strategies of S2, proposed the biogas upgrading in the HRAP and the digestate recovery as a biofertilizer. After normalization, human carcinogenic toxicity was the most positively affected category due to water use in the cultivation step, accounted as avoided product. However, this category was also the most negatively affected by the impacts of the digester heating energy. Anaerobic digestion was the most impactful step, constituting on average 60.37% of total impacts. Scenario S3 performed better environmentally, primarily due to the integration of biogas upgrading within the cultivation reactor and digestate use as a biofertilizer. Sensitivity analysis highlighted methane yield's importance, showing potential for an 11.28% reduction in ionizing radiation impacts with a 10% increase. Comparing S3 biogas with natural gas, the resource scarcity impact was reduced sixfold, but the human health impact was 23 times higher in S3.

Wastewater-grown microalgae biomass as a source of sustainable aviation fuel: Life cycle assessment comparing hydrothermal routes.

The present paper compared, through life cycle assessment (LCA), the production of aviation biofuel from two hydrothermal routes of microalgae cultivated in wastewater. Hydrothermal liquefaction (HTL) and gasification followed by Fischer-Tropsch synthesis (G + FT) were compared. Both routes included biomass production, hydrotreatment for biofuel upgrading, and product fractionation. Secondary data obtained from the literature were used for the cradle-to-gate LCA. G + FT had a higher impact than HTL in the 18 impact categories assessed, with human carcinogenic toxicity exerting the most harmful pressure on the environment. The catalysts were the inputs that caused the most adverse emissions. The solvent used for bio-oil separation also stood out in terms of impacts. In HTL, emissions for global warming were -51.6 g CO2 eq/MJ, while in G + FT, they were 250 g CO2 eq/MJ. At the Endpoint level, HTL resulted in benefits to human health and ecosystems, while G + FT caused environmental damage in these two categories, as well as in the resources category. In the improvement scenarios, besides considering solid, aqueous, and gaseous products as co-products rather than just as waste/emissions, a 20% reduction in catalyst consumption and 90% recovery were applied. Thus, in HTL, 39.47 kg CO2 eq was avoided, compared to 35.44 kg CO2 eq in the base scenario. In G + FT, emissions decreased from 147.55 kg CO2 eq to the capture of 8.60 kg CO2 eq.

Municipal and industrial wastewater blending: Effect of the carbon/nitrogen ratio on microalgae productivity and biocompound accumulation.

Municipal wastewater (MW) and industrial wastewater from juice processing (IWJ) were blended in different proportions to assess the effect of the carbon/nitrogen (C/N) ratio on pollutant removal, microalgal biomass (MB) cultivation, and the accumulation of carotenoids and biocompounds. MB development was not observed in treatments with higher C/N ratios (>30.67). The wastewater mixture favored the removal of dissolved organic carbon (75.61 and 81.90%) and soluble chemical oxygen demand (66.78-88.85%), compared to the treatment composed exclusively of MW (T7). Treatments T3 and T6 (C/N ratio equal to 30.67 and 7.52, respectively) showed higher Chlorophyll-a concentrations, 1.47 and 1.54 times higher than T7 (C/N ratio 1.75). It was also observed that the C/N ratio of 30.67 favored the accumulation of carbohydrates and lipids (30.07% and 26.39%, respectively), while the C/N ratio of 7.52 improved protein accumulation (33.00%). The fatty acids C16:0, C18:1, C18:2, and C18:3 had the highest concentrations. Additionally, increasing the C/N ratio can be an efficient strategy to improve the production of fatty acids for biofuels, mainly due to the increased concentration of shorter-chain fatty acids (C16:0). These findings suggest that blending wastewater not only enhances treatment performance but also increases the accumulation of valuable carbohydrates and lipids in MB, and optimizes fatty acid production for biofuel applications. This research represents significant progress towards feasibility of using MB produced from wastewater.

Biofuel from wastewater-grown microalgae: A biorefinery approach using hydrothermal liquefaction and catalyst upgrading.

Third-generation biofuels from microalgae are becoming necessary for sustainable energy. In this context, this study explores the hydrothermal liquefaction (HTL) of microalgae biomass grown in wastewater, consisting of 30% Chlorella vulgaris, 69% Tetradesmus obliquus, and 1% cyanobacteria Limnothrix planctonica, and the subsequent upgrading of the produced bio-oil. The novelty of the work lies in integrating microalgae cultivation in wastewater with HTL in a biorefinery approach, enhanced using a catalyst to upgrade the bio-oil. Different temperatures (300, 325, and 350 °C) and reaction times (15, 30, and 45 min) were tested. The bio-oil upgrading occurred with a Cobalt-Molybdenum (CoMo) catalyst for 1 h at 375 °C. Post-HTL, although the hydrogen-to-carbon (H/C) ratio decreased from 1.70 to 1.38-1.60, the oxygen-to-carbon (O/C) ratio also decreased from 0.39 to 0.079-0.104, and the higher heating value increased from 20.6 to 36.4-38.3 MJ kg-1. Palmitic acid was the main component in all bio-oil samples. The highest bio-oil yield was at 300 °C for 30 min (23.4%). Upgrading increased long-chain hydrocarbons like heptadecane (5%), indicating biofuel potential, though nitrogenous compounds such as hexadecanenitrile suggest a need for further hydrodenitrogenation. Aqueous phase, solid residues, and gas from HTL can be used for applications such as biomass cultivation, bio-hydrogen, valuable chemicals, and materials like carbon composites and cement additives, promoting a circular economy. The study underscores the potential of microalgae-derived bio-oil as sustainable biofuel, although further refinement is needed to meet current fuel standards.

Enhancing microalgae biomass production: Exploring improved scraping frequency in a hybrid cultivation system.

Recently, hybrid systems, such as those incorporating high-rate algal ponds (HRAPs) and biofilm reactors (BRs), have shown promise in treating domestic wastewater while cultivating microalgae. In this context, the objective of the present study was to determine an improved scraping frequency to maximize microalgae biomass productivity in a mix of industrial (fruit-based juice production) and domestic wastewater. The mix was set to balance the carbon/nitrogen ratio. The scraping strategy involved maintaining 1 cm wide stripes to retain an inoculum in the reactor. Three scraping frequencies (2, 4, and 6 days) were evaluated. The findings indicate that a scraping frequency of each 2 days provided the highest biomass productivity (18.75 g total volatile solids m-2 d-1). The species' behavior varied with frequency: Chlorella vulgaris was abundant at 6-day intervals, whereas Tetradesmus obliquus favored shorter intervals. Biomass from more frequent scraping demonstrated a higher lipid content (15.45%). Extrapolymeric substance production was also highest at the 2-day frequency. Concerning wastewater treatment, the system removed 93% of dissolved organic carbon and ∼100% of ammoniacal nitrogen. Combining industrial and domestic wastewater sources to balance the carbon/nitrogen ratio enhanced treatment efficiency and biomass yield. This study highlights the potential of adjusting scraping frequencies in hybrid systems for improved wastewater treatment and microalgae production.

Microalgae biomass as a conditioner and regulator of soil quality and fertility.

Characteristics of an acid soil cultivated with Urochloa brizantha cv. Marandu were evaluated in relation to two types of fertilization: a conventional one, chemical based on nitrogen and potassium, and a biofertilizer, based on microalgae biomass. The results were compared among three treatments, control, conventional, and biological fertilization, with seven replications each. The study evaluated microalgae community, total carbon and nitrogen contents, mineral nitrogen, and enzymatic activity. Chlorella vulgaris showed the highest organism density, which can be explained by its rapid growth and high resistance. The highest species diversity was detected in the control 1,380,938 org cm-3 and biological 1,841,250 org cm-3 treatments, with the latter showing a higher density of cyanobacteria, especially Pseudanabaena limnetica with 394,554 org cm-3. The soil treated with chemical fertilization showed higher nitrate (9.14 mg NKg-1 NO3--N) and potassium (52.32 mg dm-3) contents. The highest levels of sulfur (21.73 mg dm-3) and iron (96.46 mgdm-3) were detected in the biological treatment. The chemical treatment showed higher activity of the enzymes acid phosphatase, acetylglucosaminidase, and sulfatase, while α-glucosidase and leucine aminopeptidase stood out in the biological treatment. Soil properties were not significantly affected by the treatments. The use of microalgae biomass derived from wastewater treatment from milking parlors was evaluated and presented as a promising biofertilizer for agriculture, following the line of recovering nutrient-rich wastes. In this sense, although many challenges need to be overcome, the results suggest that microalgal-based fertilizers could lead to low-impact agriculture.

A life cycle assessment of energy recovery using briquette from wastewater grown microalgae biomass.

Microalgae biomass (MB) is a promising source of renewable energy, especially when the cultivation is associated with wastewater treatment. However, microalgae wastewater technologies still have much to improve. Additionally, microalgae biomass valorization routes need to be optimized to be a sustainable and feasible source of green bioenergy. Thus, this paper aimed to evaluate the environmental impacts of the production of briquettes from MB, cultivated during domestic wastewater treatment. Also, it was evaluated how much the drying of the MB affected the life cycle and the environment. Improvements in the life cycle to mitigate the environmental impacts of this energy route were proposed. Cradle-to-gate modeling was applied to obtain a life cycle assessment (LCA) from cultivation to the valorization of MB, through its transformation into a solid biofuel. With LCA, it was possible to identify which technical aspect of the process needs to be optimized so that environmental sustainability can be achieved. Two scenarios were compared, one with the microalgae growth in a high-rate algal pond (HRAP) (scenario 1) and the other in a hybrid reactor, formed by a HRAP and a biofilm reactor (BR) (scenario 2). LCA highlighted the electric power mix, representing, on average, 60% of the total environmental impacts in both scenarios. The valorization of MB in briquettes needs to consume less energy to offset its yield. The environment suffered pressure in freshwater eutrophication, due to the release of 3.1E-05 and 3.9E-05 kg of phosphorus equivalent; in fossil resources scarcity, with the extraction of 1.4E-02 and 4.5E-02 kg of oil equivalent; and in climate change, by the emission of 1.0E-01 and 1.9E-01 kg of carbon dioxide (CO2) equivalent, in scenarios 1 and 2, respectively. Scenario 1 was highly damaging to terrestrial ecotoxicity, with the release of 3.5E-01 kg of 1,4 Dichlorobenzene, coming from the CO2 used in MB growth. This category was the one that most negatively pressured the environment, differing from scenario 2, in which this input was not required. This was the only impact category in which scenario 2 had a better environmental performance when compared to scenario 1. Cotton, required in scenario 2, represented up to 87% of emissions in some of the evaluated categories. Despite the impacts that occurred in the two modeled scenarios, the environmental gains due to the use of wastewater for microalgae growth, replacing the synthetic cultivation medium, stood out. In the sensitivity analysis, two alternative scenarios were proposed: (i) electricity consumption for drying has been reduced, due to the natural decrease of MB humidity, and (ii) MB briquettes were considered a substitute for coal briquettes. Results indicated that pressures on climate change and fossil resource scarcity were eliminated in both scenarios and this also occurred for freshwater eutrophication in scenario 2. This paper contributes to the improvement and development of converting MB routes into more sustainable products, causing less pressure on the environment. Also, the study contributes to filling a gap in the literature, discussing methods and technologies to be improved, and consequently making microalgae biotechnology environmentally feasible and a potential renewable energy alternative.

Swine wastewater treatment in high rate algal ponds: Effects of Cu and Zn on nutrient removal, productivity and biomass composition.

This study aimed to evaluate the simultaneous interferences of Cu and Zn found in swine wastewater (SW) in the development of microalgae considering real conditions of cultivation in high rate algal ponds (HRAPs). Ten HRAPs on a pilot scale were fed with SW with different mixtures of Cu (0.5-3.0 mg/L) and Zn (5.0-25.0 mg/L). The interferences of these metals in removing nutrients (N-NH4+ and soluble phosphorus (Ps)) from the SW were determined. In addition, this study evaluated the effects on biomass growth and biochemical composition. Chlorella sp. was dominant in all HRAPs and the condition that potentiated its growth occurred in medium containing 1.8 mg Cu/L + 15.0 mg Zn/L, while higher concentrations conferred inhibition. Only Cu compromised the removal rates of N-NH4+ while the effects of Zn were not significant. Contrary, Zn interfered with Ps removal rates, but the impact of Cu was not significant. The greatest Cu applications increased the protein levels by biomass (50.5-55.2 %). Carbohydrate accumulation was favored by conditions that inhibited the development of microalgae due to either limitation or excess of metals. Copper and Zn compromised the levels of lipids, and the control treatment had the highest content (24.5 %). The presence of Cu and Zn changed the dynamics of HRAPs regarding nutrient removal, productivity, and biochemical composition of the biomass.

Fires dynamics in the Pantanal: Impacts of anthropogenic activities and climate change.

Anthropogenic activities responsible for modifying climatic regimes and land use and land cover (LULC) have been altering fire behavior even in regions with natural occurrences, such as the Pantanal. This biome was highlighted in 2020 due to the record number of fire foci and burned areas registered. Thus, this study aimed to understand how changes in LULC and climate affect the spatial, temporal and magnitude dynamics of fire foci. The Earth Trends Modeler (ETM) was used to identify trends in spatiotemporal bases of environmental and climatic variables. No trend was identified in the historical series of precipitation data. However, an increasing trend was observed for evapotranspiration, normalized difference vegetation index (NDVI) and temperature. For soil moisture, a decreasing trend was observed. The comparison between the mean of the historical series and the year 2020 showed that the variables precipitation, temperature, soil moisture and evapotranspiration had atypical behavior. Such behavior may have contributed to creating a drier environment with available combustible material, leading to a record number of burned areas, about three million hectares (248%) higher than the historical average. The 2020 fire foci data were used in two types of spatial statistical analyses: Grouping, showing that 76% of the registered fire foci were at high risk of fire and; Hot and Cold Spots, indicating high concentrations of Hot Spots in the northern region of the Pantanal, close to Cerrado and Amazon biomes agricultural frontier. The results of the Land Change Modeler (LCM) tool evidenced a strong transition potential from the natural vegetation to agriculture and pasture in the eastern region of the Pantanal, indicating that this could be, in the future, a region of high concentration of fire foci and possibly high risk of fire. This tool also allowed the prediction of a scenario for 2030 that showed that if measures for environmental protection and combating fires are not adopted, in this year, 20% of the Pantanal areas will be for agricultural and pasture use. Finally, the results suggest that the advance of agriculture in the Pantanal and changes in climatic and environmental variables boosted the increase in fire foci and burned areas in the year 2020.

Innovative hybrid system for wastewater treatment: High-rate algal ponds for effluent treatment and biofilm reactor for biomass production and harvesting.

The use of algal biomass still faces challenges associated with the harvesting stages. To address this issue, we propose an innovative hybrid system, in which a biofilm reactor (BR) operates as an algal biomass production and harvesting unit connected to a high-rate algal pond (HRAP), a wastewater treatment unit. BR did not interfered with the biomass chemical composition (protein = 32%, carbohydrates = 11% and total lipids = 18%), with the wastewater treatment (removals efficiency: chemical oxygen demand = 59%, ammonia nitrogen = 78%, total phosphorus = 16% and Escherichia coli = 1 log unit), and did not alter the sedimentation characteristics of the biomass (sludge volume index = 29 mg/L and humidity content = 92%) in the secondary settling tank of the hybrid system. On the other hand, the results showed that this technology achieved a biomass production about 2.6x greater than the conventional system without a BR, and the efficiency of harvesting of the hybrid system was 61%, against 22% obtained with the conventional system. In addition, the BR promoted an increase in the density (~1011 org/m2) and diversity of microalgae in the hybrid system. Chlorella vulgaris was the most abundant species (>60%) from the 4th week of operation until the end of the experiment. Hence, results confirm that the integration of BR into a wastewater treatment plant optimised the production and harvesting of biomass of the hybrid system, making it a promising technology. The importance of economic and environmental analysis studies of BR is highlighted in order to enable its implementation on a large scale.

Determination of the spatial susceptibility to Yellow Fever using a multicriteria analysis.

BACKGROUND: The outbreak of sylvatic Yellow Fever (SYF) in humans during 2016-2017 in Brazil is one of the greatest in the history of the disease. The occurrence of the disease in areas with low vaccination coverage favoured the dissemination of the disease; therefore, it is necessary to identify the areas vulnerability to the YF virus (YFV) to assist in the adoption of preventive measures. OBJECTIVE: To correlate the physical-environmental elements associated with the occurrence of SYF in humans via a multicriteria analysis. METHODS: For the multicriteria analysis, preponderant elements related to SYF occurrences, including soil usage and coverage, temperature, precipitation, altitude, mosquito transmitters, and non-human primate occurrence areas, were considered. The results were validated by assessing the correlation between the incidence of SYF and the vulnerable areas identified in the multicriteria analysis. RESULTS: Two regions with different vulnerability to the occurrence of the disease were identified in the multicriteria analysis, with emphasis on the southern areas of the state of São Paulo northeast areas of Minas Gerais, and the entire states of Rio de Janeiro and Espírito Santo. The map of SYF vulnerability obtained in the multicriteria analysis coincides with the areas in which cases of the disease have been recorded. The regions that presented the greatest suitability were in fact the municipalities with the highest incidence. MAIN CONCLUSIONS: The multicriteria analysis revealed that the elements that were used are suited for and consistent in the prediction of the areas that are vulnerable to SYF. The results obtained indicate the proximity of the areas that are most vulnerable to the disease to densely populated areas where an Aedes aegypti infestation was observed, which confers a high risk of re-urbanisation of YF.

Environmental fragility and vegetation cover dynamics in the Lapa Grande State Park, MG, Brazil.

The environmental fragility analysis evaluates the susceptibility of an environment to degradation. Thus, the goals of this work are to analyze and map the environmental fragility of the Lapa Grande State Park (PELG), Brazil, and its buffer zone (ZA) and also quantify the changes in the vegetation cover before and after the implementation of the PELG. The environmental fragility was evaluated through multicriteria analysis using the factors: slope, geology, pedology and land use and land cover. The changes in the high vigor vegetation cover were determined from the normalized difference vegetation index (NDVI) for 1996, 2006 and 2016. It was verified that the central-east and northeast regions of the PELG presented the greatest environmental fragilities in 1996, and significant reductions in the areas with high and very high fragility were observed in 2006 and 2016 due to the increase in the vegetation cover after the implementation of the PELG, which was more expressive in the park area than in the ZA. The increase of 20.7% of 2006 to 2016 in the vegetation with greater vigor, proved the importance of the creation of a conservation unit.

Energetic valorization of algal biomass in a hybrid anaerobic reactor.

This study evaluated the operation of a hybrid anaerobic reactor fed with algal biomass cultivated in effluent from the brewery industry. Three stages of operation were distinguished during the 72 days of semi-continuous functioning of the reactor: Stage 1 (S1), in which algal biomass was used as substrate; Stage 2 (S2), in which 10% (v/v) of the algal biomass was substituted by olive mill wastewater (OMW); and Stage 3 (S3), in which algal biomass was heat pre-treated. During S1, a loss of solids was observed, with an increment of organic matter in the outlet. The substitution of 10% of the volume of algal biomass by OMW tripled the methane productivity obtained in the previous stage by digestion of pure algal biomass. Heat pre-treatment was not efficient in rupturing the cell wall, and consequently did not have any effect on the increase in biogas production. The complementarity of substrates in the assessed conditions led to better results than the pre-treatment of the algal biomass.

Microalgae cultivation in agro-industrial effluents for biodiesel application: effects of the availability of nutrients.

The present study evaluated the cultivation of microalgae in a photobioreactor using effluents from the meat-processing industry, which had been previously treated at the primary and secondary levels. Scenedesmus sp. was the dominant genus in the phytoplankton community in both of the evaluated effluents. The different nutritional conditions affected the production of biomass, which reached 1,160 mg/L of volatile suspended solids (VSS) and 371 mg/L of VSS with cultivation in the primary (PE) and secondary effluents (SE), respectively. In both effluents, great removal efficiencies close to quantification limits were observed for ammoniacal nitrogen and soluble phosphorus. Regarding the accumulation of lipids, there were no considerable differences between the effluents. The highest lipid productivity that was observed in the PE, which reached 3.7 g/m²·d, was attributed to its larger production of biomass as a consequence of its better nutritional condition in relation to the SE.

Energy recovery in high rate algal pond used for domestic wastewater treatment.

High rate algal pond (HRAP) was evaluated according to its energy potential and productivity by two rates, net energy ratio (NER) and specific biomass productivity. All energy inputs were calculated according to one HRAP with pre-ultraviolet disinfection treating anaerobic domestic sewage. The outputs were calculated for two energetic pathways: lipid and biogas production for the raw biomass (RB) and biomass after lipid extraction. The non-polar lipid content in dry biomass was 7.6%, reaching a daily lipid productivity of 0.2 g/m2·day and the biogas production potential was 0.20 m3/kg solids. For the biomass after lipid extraction, the biogas production reached 2.6 m3/kg solids. NER values of 10-3 for the RB were similar for lipids and biogas routes. The specific biomass productivity was 0.7 mg/kJ. For the residual biomass, after lipid extraction, NER value was 10-2 for the integrated route (lipids + biogas) and the specific biomass productivity of the extracted biomass was 0.4 mg/kJ. The best energetic pathway was to integrate both lipids and biogas route.

Biodiesel from wastewater: lipid production in high rate algal pond receiving disinfected effluent.

The production of different species of microalgae in consortium with other micro-organisms from wastewaters may represent an alternative process, to reduce the costs, for obtaining biofuels. The aim of this study was to evaluate the influence of pre-ultraviolet disinfection (UV) in the production of lipids from biomass produced in high rate ponds. Two high rate algal ponds were evaluated: a pond that received domestic sewage without disinfection and the other receiving domestic sewage previously disinfected by UV radiation (uvHRAP). The UV disinfection did not lead to significant differences in fatty acid profile and total lipid productivities, although it increased algal biomass concentration and productivity as well as lipid content. Moreover, the overall biomass concentrations and productivities decreased with the UV disinfection, mostly as a consequence of a loss in bacterial load. We thus conclude that uvHRAP disinfection may represent a potential strategy to promote the cleaner and safer growth of algal biomass when cultivated in consortium with other micro-organisms. Mainly regarding the use of wastewater as culture medium, together with a cheaper production of lipids for biodiesel, pre-disinfection may represent an advance since extraction costs could be significantly trimmed due to the increase in lipid content.

Effect of solar radiation on the lipid characterization of biomass cultivated in high-rate algal ponds using domestic sewage.

The objective of this paper is to compare the lipid content and composition ofbiomass produced by a consortium of microalgae and bacteria, cultivated under different solar radiation intensities and tropical conditions in pilot-scale high-rate ponds (HRPs) using domestic sewage as culture medium. The treatment system consisted of an upflow anaerobic sludge blanket reactor followed by UV disinfection and six HRPs covered with shading screens that blocked 9%, 18%, 30%, 60% and 80% of the solar radiation. The total lipid content does not vary significantly among the units, showing a medium value of 9.5%. The results show that blocking over 30% of the solar radiation has a negative effect on the lipid productivity. The units with no shading and with 30% and 60% of solar radiation blocking have statistically significant lipid productivities, varying from 0.92 to 0.96 gm(-2) day(-1). Besides radiation, other variables such as volatile suspended solids and chlorophyll-a are able to explain the lipid accumulation. The lipid profile has a predominance of C16, C18:1 and C18:3 acids. The unsaturation of fatty acids increases with the reduction in solar radiation. On the other hand, the effect of polyunsaturation is not observed, which is probably due to the presence of a complex and diverse biomass.

Biocompounds from wastewater-grown microalgae: a review of emerging cultivation and harvesting technologies.

Microalgae biomass has attracted attention as a feedstock to produce biofuels, biofertilizers, and pigments. However, the high production cost associated with cultivation and separation stages is a challenge for the microalgae biotechnology application on a large scale. A promising approach to overcome the technical-economic limitations of microalgae production is using wastewater as a nutrient and water source for cultivation. This strategy reduces cultivation costs and contributes to valorizing sanitation resources. Therefore, this article presents a comprehensive literature review on the status of microalgae biomass cultivation in wastewater, focusing on production strategies and the accumulation of valuable compounds such as lipids, carbohydrates, proteins, fatty acids, and pigments. This review also covers emerging techniques for harvesting microalgae biomass cultivated in wastewater, discussing the advantages and limitations of the process, as well as pointing out the main research opportunities. The novelty of the study lies in providing a detailed analysis of state-of-the-art and potential advances in the cultivation and harvesting of microalgae, with a special focus on the use of wastewater and implementing innovative strategies to enhance productivity and the accumulation of compounds. In this context, the work aims to guide future research concerning emerging technologies in the field, emphasizing the importance of innovative approaches in cultivating and harvesting microalgae for advancing knowledge and practical applications in this area.

Algal biomass production and wastewater treatment in high rate algal ponds receiving disinfected effluent.

Algal biomass production associated with wastewater is usually carried out in high rate algal ponds (HRAPs), which are concomitantly used in the treatment of such effluent. However, most types of wastewater have high levels of bacteria that can inhibit the growth of algal biomass by competing for space and nutrients. The objective of this study was to assess the influence of ultraviolet (UV) pre-disinfection on the performance of HRAPs used for wastewater treatment and algal biomass production. Two HRAPs were tested: one received effluent from an upflow anaerobic sludge blanket (UASB) reactor- HRAP -and the second received UASB effluent pre-disinfected by UV radiation-(UV)HRAP. Physical, chemical and microbiological parameters were monitored, as well as algal biomass productivity and daily pH and dissolved oxygen (DO) variation. The (UV)HRAP presented highest DO and pH values, as well as greater percentage of chlorophyll a in the biomass, which indicates greater algal biomass productivity. The average percentages of chlorophyll a found in the biomass obtained from the HRAP and the (UV)HRAP were 0.95 +/- 0.65% and 1.58 +/- 0.65%, respectively. However, total biomass productivity was greater in the HRAP (11.4 gVSSm(-2) day(-1)) compared with the (UV)HRAP (9.3 gVSSm(-2) day(-1)). Mean pH values were 7.7 +/- 0.7 in the HRAP and 8.1 +/- 1.0 in the (UV)HRAP, and mean values of DO percent saturation were 87 +/- 26% and 112 +/- 31% for the HRAP and the (UV)HRAP, respectively. Despite these differences, removal efficiencies of organic carbon, chemical oxygen demand, ammoniacal nitrogen and soluble phosphorus were statistically equal at the 5% significance level.