A Synthetic Overview of Preparation Protocols of Nonmetallic, Contact-Active Antimicrobial Quaternary Surfaces on Polymer Substrates.

Antibacterial surfaces have been researched for more than 30 years and remain highly desirable. In particular, there is an interest in providing antimicrobial properties to commodity plastics, because these, in their native state, are excellent substrates for pathogens to adhere and proliferate on. Therefore, efficient strategies for converting surfaces of commodity plastics into contact-active antimicrobial surfaces are of significant interest. Many systems have been prepared and tested for their efficacy. Here, the synthetic approaches to such active surfaces are reviewed, with the restriction to only include systems with tested antibacterial properties. The review focuses on the synthetic approach to surface functionalization of the most common materials used and tested for biomedical applications, which effectively has limited the study to quaternary materials. For future developments in the field, it is evident that there is a need for development of simple methods that permit scalable production of active surfaces. Furthermore, in terms of efficacy, there is an outstanding concern of a lack of universal antimicrobial action as well as rapid deactivation of the antibacterial effect through surface fouling.

How Dissociation of Carboxylic Acid Groups in a Weak Polyelectrolyte Brush Depend on Their Distance from the Substrate.

A weak polyelectrolyte brush is composed of a layer of polyacids or polybases grafted by one end of their chains to a substrate surface. For such brush layers immersed in an aqueous solution, the dissociation behavior of the acidic or basic groups and the structural and physical properties of the brush layer will thus be strongly dependent on the environmental conditions. For a polyacid brush layer consisting of, e.g., poly(acrylic acid), this means that the chains in the brush layer will be charged at high pH and uncharged at low pH. However, theoretical scaling laws not only foresee the structural changes occurring in response to the pH-induced dissociation behavior but also how the dissociation behavior of the brush layer depends on the ionic strength of the aqueous solution and the density of acidic groups within the brush layer. We have herein employed spectroscopic ellipsometry and a quartz crystal microbalance with dissipation monitoring (QCM-D) to experimentally evaluate the theoretically predicted dissociation and structural behavior of PAA brushes. Spectroscopic ellipsometry allows us to study the brush thickness as a function of pH and ionic strength, while QCM-D gives us an opportunity to investigate the swelling behavior of PAA brushes at various penetration depths of propagating acoustic waves. Our studies show that the dissociation degree of the carboxylic acid groups in a PAA brush increases with increasing distance from the substrate. Moreover, the ionic strength enhances carboxylic acid dissociation, such that a higher ionic strength leads to a narrower distribution and higher average dissociation degree. In conclusion, our results provide an experimental verification of the theoretically predicted gradient in the degree of dissociation of the acid groups in weak polyacid brush layers and shows that at a pH value equal to approximately the average pKa value of the brush, the state of the acid groups varies from being almost uncharged to almost fully dissociated depending on the ionic strength and vertical position in the brush.

Are We Speaking the Same Language? Recommendations for a Definition and Categorization Framework for Plastic Debris.

The accumulation of plastic litter in natural environments is a global issue. Concerns over potential negative impacts on the economy, wildlife, and human health provide strong incentives for improving the sustainable use of plastics. Despite the many voices raised on the issue, we lack a consensus on how to define and categorize plastic debris. This is evident for microplastics, where inconsistent size classes are used and where the materials to be included are under debate. While this is inherent in an emerging research field, an ambiguous terminology results in confusion and miscommunication that may compromise progress in research and mitigation measures. Therefore, we need to be explicit on what exactly we consider plastic debris. Thus, we critically discuss the advantages and disadvantages of a unified terminology, propose a definition and categorization framework, and highlight areas of uncertainty. Going beyond size classes, our framework includes physicochemical properties (polymer composition, solid state, solubility) as defining criteria and size, shape, color, and origin as classifiers for categorization. Acknowledging the rapid evolution of our knowledge on plastic pollution, our framework will promote consensus building within the scientific and regulatory community based on a solid scientific foundation.

Simple Preparation of Thiol-Ene Particles in Glycerol and Surface Functionalization by Thiol-Ene Chemistry (TEC) and Surface Chain Transfer Free Radical Polymerization (SCT-FRP).

Thiol-ene (TE)-based polymer particles are traditionally prepared via emulsion polymerization in water (using surfactants, stabilizers, and cosolvents). Here, a green and simple alternative is presented with excellent control over particle size, while avoiding the addition of stabilizers. Glycerol is applied as a dispersing medium for the preparation of off-stoichiometric TE microparticles, where sizes in the range of 40-400 µm are obtained solely by changing the mixing speed of the emulsions prior to crosslinking. Control over surface chemistry is achieved by surface functionalization of excess thiol groups via photochemical thiol-ene chemistry resulting in a functional monolayer. In addition, surface chain transfer free radical polymerization is used for the first time to introduce a thicker polymer layer on the particle surface. The application potential of the system is demonstrated by using functional particles as adsorbent for metal ions and as a support for immobilized enzymes.

The Current State of Silicone-Based Dielectric Elastomer Transducers.

Silicone elastomers are promising materials for dielectric elastomer transducers (DETs) due to their superior properties such as high efficiency, reliability and fast response times. DETs consist of thin elastomer films sandwiched between compliant electrodes, and they constitute an interesting class of transducer due to their inherent lightweight and potentially large strains. For the field to progress towards industrial implementation, a leap in material development is required, specifically targeting longer lifetime and higher energy densities to provide more efficient transduction at lower driving voltages. In this review, the current state of silicone elastomers for DETs is summarised and critically discussed, including commercial elastomers, composites, polymer blends, grafted elastomers and complex network structures. For future developments in the field it is essential that all aspects of the elastomer are taken into account, namely dielectric losses, lifetime and the very often ignored polymer network integrity and stability.

Recycled PMMA prepared directly from crude MMA obtained from thermal depolymerization of mixed PMMA waste.

Recycled PMMA was prepared by directly polymerizing crude pyrolysis oils from lab-scale pyrolysis of collected industrial waste PMMA. The pyrolysis oils consisted mainly of methyl methacrylate (MMA, >85%), while the type and number of by-products from the thermal process were assigned through GC-MS analysis showing a clear correlation to the pyrolysis temperature. By-products can be removed by distillation; however, directly employing the crude oils to prepare PMMA through solution, suspension, emulsion, or casting polymerization was investigated to assess the potential for omitting this costly step. It was found that the crude pyrolysis oils could be polymerized efficiently via solution, emulsion, and casting polymerization to produce a polymer similar to the PMMA prepared from a pristine monomer. The impurities in the PMMAs prepared from the crude mixtures were investigated by extraction analyses followed by screening by GC-MS. In the case of casting polymerization, the GC-MS analysis, as expected, revealed various residual by-products, while solution and emulsion polymerization showed only very few impurities, mainly originating from the polymerization and not the feed material. Additional purification of the crude pyrolysis oils would be required for applications in casting polymerization. In contrast, direct polymerization by emulsion or solution polymerization is considered applicable for producing pristine PMMA from crude waste PMMA pyrolysis oil.

Micropatterning of functional conductive polymers with multiple surface chemistries in register.

A versatile procedure is presented for fast and efficient micropatterning of multiple types of covalently bound surface chemistry in perfect register on and between conductive polymer microcircuits. The micropatterning principle is applied to several types of native and functionalized PEDOT (poly(3,4-ethylenedioxythiophene)) thin films. The method is based on contacting PEDOT-type thin films with a micropatterned agarose stamp containing an oxidant (aqueous hypochlorite) and applying a nonionic detergent. Where contacted, PEDOT not only loses its conductance but is entirely removed, thereby locally revealing the underlying substrate. Surface analysis showed that the substrate surface chemistry was fully exposed and not affected by the treatment. Click chemistry could thus be applied to selectively modify re-exposed alkyne and azide functional groups of functionalized polystyrene substrates. The versatility of the method is illustrated by micropatterning cell-binding RGD-functionalized PEDOT on low cell-binding PMOXA (poly(2-methyl-2-oxazoline)) to produce cell-capturing microelectrodes on a cell nonadhesive background in a few simple steps. The method should be applicable to a wide range of native and chemically functionalized conjugated polymer systems.

Antimicrobial PDMS Surfaces Prepared through Fast and Oxygen-Tolerant SI-SARA-ATRP, Using Na2SO3 as a Reducing Agent.

Poly(dimethylsiloxane) (PDMS) is an attractive, versatile, and convenient material for use in biomedical devices that are in direct contact with the user. A crucial component in such a device is its surface in terms of antimicrobial properties preventing infection. Moreover, due to its inherent hydrophobicity, PDMS is rather prone to microbial colonization. Thus, developing an antimicrobial PDMS surface in a simple, large-scale, and applicable manner is an essential step in fully exploiting PDMS in the biomedical device industry. Current chemical modification methods for PDMS surfaces are limited; therefore, we present herein a new method for introducing an atom transfer radical polymerization (ATRP) initiator onto the PDMS surface via the base-catalyzed grafting of [(chloromethyl)phenylethyl]trimethoxysilane to the PDMS. The initiator surface was grafted with poly[2-(dimethylamino)ethyl methacrylate] (PDMAEMA) brushes via a surface-initiated supplemental activator and reducing agent ATRP (SI-SARA-ATRP). The use of sodium sulfite as a novel reducing agent in SI-SARA-ATRP allowed for polymerization during complete exposure to air. Moreover, a fast and linear growth was observed for the polymer over time, leading to a 400 nm thick polymer layer in a 120 min reaction time. Furthermore, the grafted PDMAEMA was quaternized, using various alkylhalides, in order to study the effect on surface antimicrobial properties. It was shown that antimicrobial activity not only depended highly on the charge density but also on the amphiphilicity of the surface. The fast reaction rate, high oxygen tolerance, increased antimicrobial activity, and the overall robustness and simplicity of the presented method collectively move PDMS closer to its full-scale exploitation in biomedical devices.

Complex surface concentration gradients by stenciled "electro click chemistry".

Complex one- or two-dimensional concentration gradients of alkynated molecules are produced on azidized conducting polymer substrates by stenciled "electro click chemistry". The latter describes the local electrochemical generation of catalytically active Cu(I) required to complete a "click reaction" between alkynes and azides at room temperature. A stencil on the counter electrode defines the shape and multiplicity of the gradient(s) on the conducting polymer substrate, while the specific reaction conditions control gradient steepness and the maximum concentration deposited. Biologically active ligands including cell binding peptides are patterned in gradients by this method without losing their biological function or the conductivity of the polymer.

Dendronized macromonomers for three-dimensional data storage.

A series of dendritic macromonomers have been synthesized and utilized as the photoactive component in holographic storage systems leading to high performance, low shrinkage materials.

Development of a thiol-ene based screening platform for enzyme immobilization demonstrated using horseradish peroxidase.

Efficient immobilization of enzymes on support surfaces requires an exact match between the surface chemistry and the specific enzyme. A successful match would normally be identified through time consuming screening of conventional resins in multiple experiments testing individual immobilization strategies. In this study we present a versatile strategy that largely expands the number of possible surface functionalities for enzyme immobilization in a single, generic platform. The combination of many individual surface chemistries and thus immobilization methods in one modular system permits faster and more efficient screening, which we believe will result in a higher chance of discovery of optimal surface/enzyme interactions. The proposed system consists of a thiol-functional microplate prepared through fast photochemical curing of an off-stoichiometric thiol-ene (OSTE) mixture. Surface functionalization by thiol-ene chemistry (TEC) resulted in the formation of a functional monolayer in each well, whereas, polymer surface grafts were introduced through surface chain transfer free radical polymerization (SCT-FRP). Enzyme immobilization on the modified surfaces was evaluated by using a rhodamine labeled horseradish peroxidase (Rho-HRP) as a model enzyme, and the amount of immobilized enzyme was qualitatively assessed by fluorescence intensity (FI) measurements. Subsequently, Rho-HRP activity was measured directly on the surface. The broad range of utilized surface chemistries permits direct correlation of enzymatic activity to the surface functionality and improves the determination of promising enzyme-surface candidates. The results underline the high potential of this system as a screening platform for synergistic immobilization of enzymes onto thiol-ene polymer surfaces. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1267-1277, 2017.