Dental implant and abutment in PEEK: stress assessment in single crown retainers on anterior region.

OBJECTIVE: Stress distribution assessment by finite elements analysis in poly(etheretherketone) (PEEK) implant and abutment as retainers of single crowns in the anterior region. MATERIALS AND METHODS: Five 3D models were created, varying implant/abutment manufacturing materials: titanium (Ti), zirconia (Zr), pure PEEK (PEEKp), carbon fiber-reinforced PEEK (PEEKc), glass fiber-reinforced PEEK (PEEKg). A 50 N load was applied 30o off-axis at the incisal edge of the upper central incisor. The Von Mises stress (σvM) was evaluated on abutment, implant/screw, and minimum principal stress (σmin) and maximum shear stress (τmax) for cortical and cancellous bone. RESULTS: The abutment σvM lowest stress was observed in PEEKp group, being 70% lower than Ti and 74% than Zr. On the implant, PEEKp reduced 68% compared to Ti and a 71% to Zr. In the abutment screws, an increase of at least 33% was found in PEEKc compared to Ti, and of at least 81% to Zr. For cortical bone, the highest τmax values were in the PEEKp group, and a slight increase in stress was observed compared to all PEEK groups with Ti and Zr. For σmin, the highest stress was found in the PEEKc. Stress increased at least 7% in cancellous bone for all PEEK groups. CONCLUSION: Abutments and implants made by PEEKc concentrate less σvM stress, transmitting greater stress to the cortical and medullary bone. CLINICAL RELEVANCE: The best stress distribution in PEEKc components may contribute to decreased stress shielding; in vitro and in vivo research is recommended to investigate this.

Clinical performance of short and extrashort dental implants with wide diameter: A systematic review with meta-analysis.

STATEMENT OF PROBLEM: Rehabilitation with wide-diameter reduced-length implants has become popular for patients with minimal vertical bone. However, a consensus on the benefits of this approach is lacking. PURPOSE: The purpose of this systematic review with meta-analysis was to evaluate the influence of wide compared with regular diameter on the clinical performance of short (<10 mm) and extrashort (≤6 mm) dental implants used for rehabilitations with single crowns, fixed partial dentures, or both, in the posterior region. MATERIAL AND METHODS: A search in 6 databases was conducted to select randomized controlled trials (RCTs) and nonrandomized controlled trials (N-RCTs). Five meta-analyses were performed, where the risk ratio (RR) was evaluated. The certainty of evidence was evaluated, and the risk of bias was determined from the Joanna Briggs Institute checklist. RESULTS: Fourteen articles were included, 272 wide- and 478 regular-diameter implants. One study presented a low, 3 an unclear, and 11 a high risk of bias. Meta-analyses showed no statistical difference: implant survival, short dental implants in N-RCTs (up to 1 year - RR 1.01 [0.98; 1.03], 1 to 5 years - RR 1.01 [0.94; 1.08], more than 5 years - RR 1.01 [0.97; 1.06]), extrashort dental implants in N-RCTs (RR 1.04 [0.90; 1.20]), RCTs (RR 1.05 [0.88; 1.25]); implant success in N-RCTs (RR 1.01 [0.97; 1.05]); prosthesis success in N-RCTs (RR 1.01 [0.97; 1.05]). CONCLUSIONS: Short and extrashort dental implants with a wide and regular diameter appear to be clinically appropriate options for implant-supported posterior restorations, with high survival, success, and prosthesis success rates.

Performance of complete dentures fabricated with the simplified and the traditional technique: A randomized clinical trial.

STATEMENT OF PROBLEM: The simplified technique has been recommended for the fabrication of removable complete dentures. However, a consensus regarding the performance of the simplified and the traditional techniques is lacking. PURPOSE: The purpose of this randomized clinical trial was to compare the performance of prostheses fabricated with the simplified and the traditional techniques. MATERIAL AND METHODS: Sixty participants were recruited and randomized into 2 groups: traditional technique (control group) and simplified technique (experimental group). The assessments were performed before treatment (baseline) and 2 and 4 months after adaptation to the new complete dentures. The variables evaluated were satisfaction, oral health-related quality of life (OHRQoL) by using the Brazilian version of the OHIP-EDENT, the quality of the prostheses, and, for the functional assessment, the masticatory performance and swallowing threshold. The data were analyzed by the Fisher exact test, the Mann-Whitney test, and the generalized equations estimating (GEE) method. RESULTS: At baseline, the mean ±standard deviation quality of the prostheses was 5.3 ±2.3 for the traditional technique and 4.9 ±2.3 for the simplified technique, and at 4 months, it was 9.3 ±0.9 and 9.1 ±0.9, respectively. For masticatory performance, the mean ±standard deviation X50 at baseline was 5.7 ±1.4 for the traditional technique and 5.7 ±0.9 for the simplified technique, and at 4 months, it was 3.8 ±1.2 and 3.7 ±0.9, respectively. The mean ±standard deviation OHRQoL at baseline was 14.1 ±8.6 for the traditional technique and 12.5 ±9.4 for the simplified technique, and at 4 months, it was 3.2 ±4.3 and 2.6 ±5.1, respectively. The mean ±standard deviation satisfaction at baseline was 9.5 ±3.9 for the traditional technique and 9.3 ±4.2 for the simplified technique; after 4 months, it was 14.8 ±2.0 for both techniques. There was a significant improvement (P<.05) for all variables in the study when comparing them at the baseline to those at the evaluation after provision of new complete dentures. There was no significant difference in all analyzed variables (P>.05) between the 2 techniques for prosthesis fabrication. CONCLUSIONS: The simplified technique appears to be a suitable alternative to the traditional technique for the fabrication of complete dentures, with similar performance.

Fatigue and failure analysis of restored endodontically treated maxillary incisors without a dowel or ferrule.

STATEMENT OF PROBLEM: Information on the survival and mode of failure of endodontically treated incisors without a ferrule and restored without dowels is lacking. PURPOSE: The purpose of this in vitro study was to compare the survival and failure mode of endodontically treated incisors without a ferrule and restored with bonded ceramic crowns and various composite resin foundation restorations without dowels with a control group with fiber dowels. MATERIAL AND METHODS: Forty-five decoronated endodontically treated bovine incisors without ferrule were divided into 3 experimental groups and restored with different adhesive foundation restorations without dowel: nanohybrid composite resin (Nd), bulk-fill composite resin foundation restoration (NdB), and fiber-reinforced bulk-fill composite resin (NdFR). A control group with conventional foundation restorations (glass-fiber dowel with nanohybrid composite resin foundation restoration without ferrule) (D) was included for comparison. All teeth were prepared to receive bonded lithium disilicate ceramic crowns luted with dual-polymerizing composite resin cement and were subjected to accelerated fatigue testing. Cyclic isometric loading was applied to the incisal edge at an angle of 30 degrees and a frequency of 5 Hz, beginning with a load of 100 N (5000 cycles). A 100-N load increase was applied each 15 000 cycles. Specimens were loaded until failure or to a maximum for cycles endured of 1000 N (140 000 cycles). Groups were compared by using the Kaplan-Meier survival analysis (log rank test at α=.05 and pairwise post hoc comparisons) and life table analysis for load-at-failure (followed by Wilcoxon pairwise comparison α=.05). RESULTS: All the specimens failed before 140 000 load cycles. Even though no statistically significant differences were found between the experimental groups without dowel (P>.127), the fiber-reinforced foundation restoration yielded the highest mean ±standard deviation cycles to failure (46 023 ±4326) compared with Nd (38 899 ±2975) and NdB (39 751 ±2998). NdFR, however, outperformed the foundation restoration with glass-fiber dowel (35 026 ±2687) (P<.05). Most failure in groups without dowel were restorable, while 100% of catastrophic failure (unrestorable) were found in the group with dowels. CONCLUSIONS: Based on the present in vitro study, dowels did not improve the performance of the adhesive restoration of endodontically treated incisors without a ferrule. The use of a short fiber-reinforced composite resin foundation restoration without a dowel was able to not only improve the resistance of the restorations compared with adhesive foundation restorations with dowels but also minimize catastrophic failures.

Implant-supported crowns with locking taper implant-abutment connection: A systematic review and meta-analysis.

STATEMENT OF PROBLEM: Implant-supported single crowns are more prone to screw loosening than splinted prostheses. Therefore, the locking taper system, which has a screwless abutment, may perform better when associated with this type of rehabilitation. However, systematic reviews on this system are lacking. PURPOSE: The purpose of this systematic review was to evaluate the clinical performance and complications of single crowns retained by the locking taper system. MATERIAL AND METHODS: This systematic review was registered at the International Prospective Register of Systematic Reviews (PROSPERO) under CRD42020189921. An electronic search was made in 5 databases and 3 other sources up to February 2021 to select prospective clinical studies evaluating the performance of single crowns retained by the locking taper system by using the outcomes implant survival, success rate, complications, marginal bone loss (MBL), and prosthesis success rate. Four meta-analyses grouped according to the follow-up intervals were performed. The risk of bias of the selected studies was evaluated by using the RoB 2 checklist for randomized controlled trials (RCTs) and Downs and Black for uncontrolled studies. RESULTS: Twelve studies were included: 9 prospective cohort studies and 3 RCTs. A survival rate of 99% (98% to 99%) and a success rate of 97% (92% to 99%) after 5 years were found. Of the total, 2.6% biological and 2.9% prosthetic complications were described. The prosthesis success rate was 97% (96% to 98%) after 5 years. An average of -0.73 mm (-0.93 to -0.52) was found for the MBL after 5 years. The risk-of-bias assessment showed 2 RCTs with high risk and 1 RCT with low risk of bias. Among uncontrolled studies, 2 were classified as poor and 7 as fair. CONCLUSIONS: Single crowns retained by locking taper implants can be safely indicated based on the high survival and success rates achieved in the long term, the maintenance of bone level stability over time, and the low incidence of complications.

Patient-reported outcome measures and clinical performance of implant-retained mandibular overdentures with stud and ball attachments: A systematic review and meta-analysis.

STATEMENT OF PROBLEM: Evidence regarding the retention system for a mandibular overdenture is important for treatment planning. However, the clinical performance of stud and ball attachments for mandibular overdenture retainers is unclear. PURPOSE: The purpose of this systematic review and meta-analysis was to compare the clinical performance and self-reported patient outcomes of ball and stud attachments as mandibular overdenture retainers. MATERIAL AND METHODS: Randomized (RCTs) and nonrandomized (N-RCTs) controlled clinical trials were selected based on the eligibility criteria. The risk of bias was assessed by using the Cochrane Collaboration Tools, and the certainty of the evidence (COE) by using the grades of recommendation, assessment, development, and evaluation (GRADE) workshop approach. Meta-analyses according to the follow-up period were performed for implant survival, prosthetic maintenance and complications, bleeding on probing (BoP), marginal bone loss (MBL), satisfaction, and oral health-related quality of life (OHRQoL). RESULTS: Thirteen RCTs and 4 N-RCTs were included. Twelve studies presented a high risk of bias. The stud demonstrated a lower risk ratio (RR) (P<.001) for maintenance and complications concerning the need for matrix activation (RR 7.12 [2.65, 19.15]) (very low COE) and new overdentures (RR 2.47 [1.02, 5.96]) (moderate COE), ranging from 1 to 5 years of follow-up. Mean difference (MD) for MBL after 1 (MD 0.40 [0.28, 0.52]; P<.001) and 5 years (MD 0.18 [0.16, 0.20]; P<.001) was higher for ball attachments than that for stud (very low COE) attachments. Stud attachments also improved satisfaction (P<.001) when compared with ball attachments (very low COE). Implant survival rate (high COE), BoP (very low COE), and OHRQoL (low COE) were similar for the attachments. CONCLUSIONS: Stud and ball attachments are clinically appropriate options as mandibular overdenture retainers and are capable of restoring OHRQoL. Nevertheless, the stud showed greater improvement in satisfaction and less prosthetic aftercare and MBL.

Influence of luting space of zirconia abutment on marginal discrepancy and tensile strength after dynamic loading.

STATEMENT OF PROBLEM: Although luting space is related to the marginal fit of indirect restorations, information on its influence on the marginal fit and tensile strength of zirconia abutments bonded to titanium bases is lacking. PURPOSE: The purpose of this in vitro study was to evaluate the influence of luting space on the marginal discrepancy and tensile strength of zirconia abutments bonded to a titanium base after dynamic loading. MATERIAL AND METHODS: Ninety implant replicas were embedded in resin blocks to attach 4-mm-high titanium luting bases. Zirconia abutments (Ceramill Zolid FX) were fabricated with different internal luting spaces: 25 µm (G25), 50 µm (G50), or 75 µm (G75). The zirconia abutments were cemented on the titanium bases by using a resin cement (Panavia F 2.0) under a constant load of 20 N. The marginal discrepancy and internal fit of 10 random specimens from each group were evaluated with a stereoscopic microscope at ×50 magnification. The remaining specimens were submitted to the tensile strength test in which half were evaluated after dynamic loading (1.2 million cycles of 200 N at 3.8 Hz) in a mechanical fatigue machine. The tensile strength test was performed using a pullout apparatus coupled to a universal testing machine at a crosshead speed of 0.5 mm/min. The mode of failure was determined by observation at ×50 magnification under a stereomicroscope and classified into adhesive or mixed. The groups were compared by using 2-way ANOVA and the Tukey HSD test (α=.05). RESULTS: Increase in the luting space did not influence the marginal discrepancy (P>.05). All zirconia abutments exhibited lower pullout strength after fatigue simulation (P<.05). G75 demonstrated lower tensile strength than G25 and G50 before and after loading (P<.05). Most failures were adhesive at the zirconia-cement interface. CONCLUSIONS: The increase of the luting space to 75 µm did not influence marginal discrepancy; however, it reduced the tensile strength of a zirconia abutment bonded to a titanium base.

Mapping of inflammatory biomarkers in the peri-implant crevicular fluid before and after the occlusal loading of narrow diameter implants.

OBJECTIVE: To monitor the cytokine release patterns in the peri-implant crevicular fluid (PICF) and to investigate which factors affect the success rate of narrow diameter implants (NDI) during the first year. MATERIAL AND METHODS: Mandibular implant overdentures (IOD) retained by 2 NDI were installed in 16 clinically atrophic edentulous patients. The following parameters were monitored during the first year: (i) peri-implant health parameters (plaque index (PI), calculus presence (CP), gingival index (GI), probing depth (PD) and bleeding on probing (BoP); (ii) cytokine concentrations in the PICF (TNF-α, IL-1ß, IL-6, IL-10); (iii) implant stability quotient (ISQ); (iv) marginal bone level (MBL) and bone level change (BLC); (v) implant success. The insertion torque, bone type, mandibular atrophy, time since edentulism, and smoking habits were also recorded. All data were analyzed using multivariable multilevel mixed-effects regression models. RESULTS: The variability in the TNF-α release patterns temporarily reduced at weeks (w) 8-12, while the IL-1ß concentrations remained low until they peaked at w48 [p < 0.05; + 177.55 pg/µl (+ 96.13 - + 258.97)]. Conversely, IL-10 release decreased significantly at w48 [p < 0.05; - 456.24 pg/µl (- 644.41 - - 268.07)]. The PD and ISQ decreased significantly (p < 0.05) over the follow-up period, while the MBL was stable after w48 with a BLC of 0.12 ± 0.71 mm. The overall success rate was 81.3%, and was influenced by TNF-α, IL-1ß, IL-10, PI, GI, PD, smoking, and time since edentulism. CONCLUSION: Pro- and anti-inflammatory cytokine release was balanced during the first 24 weeks. The GI, smoking, and time since edentulism are the most important factors determining the implant success. CLINICAL RELEVANCE: The study contributes to the understanding of the osseointegration process in a clinically atrophic population rehabilitated with IOD, and highlights the importance of monitoring clinical peri-implant health-related parameters, smoking habit, and time since edentulism to predict implant success rates.

Healing differences in narrow diameter implants submitted to immediate and conventional loading in mandibular overdentures: A randomized clinical trial.

BACKGROUND: Biological responses to different loading protocols during the bone healing phase in subjects with long time since edentulism, rehabilitated with narrow diameter implants (NDIs) to retain mandibular overdentures (MOs), are still unavailable. OBJECTIVE: This randomized clinical trial compared the peri-implant health, implant stability, and concentrations of pro- and anti-inflammatory cytokines in the peri-implant crevicular fluid (PICF) in mandibular edentulous patients under conventional (CL) and immediate loading (IML) during healing. METHODOLOGY: Twenty totally edentulous patients received two NDIs (2.9 × 10 mm, Facility NeoPoros) placed in mandible anterior region and were randomly assigned to two loading protocols: CL (n = 10) and IML (n = 10). The following clinical outcomes were evaluated 1, 2, 4, 8, and 12 weeks after surgery: (a) peri-implant tissue health (gingival index-GI, plaque index-PI, calculus-presence CP, probing depth-PD, and bleeding on probing-BOP); (b) implant stability quotient (ISQ); and (c) IL-1ß, IL-6, IL-10, and TNF-α levels in the PICF analyzed by ELISA. RESULTS: The CL group showed significantly higher CP scores at weeks 8 and 12. The IML group showed significantly higher GI from the first week onwards. The IML group presented significantly lower PD at all follow-up times, and higher BOP rates than CL at week 12. The ISQ values of the CL group were higher than those of the IML group, except at week 4. The IML group released significantly more TNF-α between weeks 1 and 4 and more IL-1ß during week 4-12, while releasing less IL-6 until week 8, mainly at week 2 (-47.6%). The release of IL-10 was similar for both groups and increased progressively over time. At week 12, the IML group released 45.74% more IL-10 than the CL group. The survival rates were 95% and 90% for CL and IML, respectively. CONCLUSION: The IML group presented more favorable PD at all evaluation times; the differences between the other clinical parameters were less systematic. The implant stability and the inflammatory marker concentrations were more stable in the CL group.

Fluoride Penetration and Clearance Are Higher in Exopolysaccharide-Containing Bacterial Pellets.

Extracellular polysaccharides (EPS) could increase the penetration of fluoride through dental biofilm, reducing its cariogenicity. We measured the concentration of fluoride in EPS-containing (EPS+) or not-containing (EPS-) Streptococcus mutans bacterial pellets resembling test biofilms, before and up to 60 min after a 0.05% NaF rinse in situ. Fluoride penetration and clearance were higher in EPS+ bacterial pellets. The data suggest that EPS enhances fluoride penetration, but also accelerates fluoride clearance from dental biofilms.

Effect of implant macrogeometry on peri-implant healing outcomes: a randomized clinical trial.

OBJECTIVES: This randomized split-mouth clinical trial investigated the influence of implant macrogeometry on bone properties and peri-implant health parameters during the healing process. MATERIAL AND METHODS: Ninety-nine implants were placed bilaterally in posterior mandibles of 23 patients that received at least four dental implant macrogeometries: standard geometry, Integra (IN) and three geometries inducing "healing chamber": Duo (D), Compact (C), and Infra (IF). Insertion torque (IT) and implant stability quotient (ISQ) were measured. Peri-implant health were monitored by visible plaque index (VPI), peri-implant inflammation (PI), and presence of calculus (CC). Data were collected during 90 days. Data were assessed for normality using the asymmetry and kurtosis coefficients followed by the Shapiro-Wilk test. A one-way ANOVA was used to investigate differences in IT and linear bone dimensions between the macrogeometry groups. The repeated measurements ANOVA test or ANOVA-R was used for analysis of ISQ, VPI, and PI. Tukey-Kramer test or Student's t test was used for comparisons between the groups or within each macrogeometry. RESULTS: Macrogeometry did not significantly influence IT and ISQ values. The minimum ISQ was recorded after 7 days (71.95 ± 12.04, p = 0.0001). Intermediate ISQ was found after 14 days, when the ISQ reached values that are statistically identical to primary stability. The VPI showed significantly higher scores for the D (0.88 ± 1.03) and IN (0.72 ± 0.94) implants after 7 days. The PI was only influenced by the healing time significantly decreasing from 7 (1.07 ± 0.89) to 21 days (0.18 ± 0.18). CONCLUSION: Implant macrogeometry did not influence IT nor ISQ values. The relationship between IT and SS was more evident for the Duo implant, but only in the final stage of healing process. CLINICAL RELEVANCE: Show to the clinician that the macrogeometry and drilling protocols did not interfere in the clinical behavior of the implants during the healing process. However, the IT, primary and secondary stability, is quite dependent of the surgeon experience.

Association between mandibular advancement device therapy and reduction of excessive daytime sleepiness due to obstructive sleep apnoea.

BACKGROUND: Excessive daytime sleepiness (EDS) is frequently reported as a symptom for obstructive sleep apnoea (OSA), leading to problems with concentration, mood and memory. Mandibular advance device (MAD) is considered as an effective therapy to control OSA, reducing EDS and improving sleep quality. OBJECTIVES: The present study aimed to investigate the effects MAD therapy on EDS of patients diagnosed with OSA. METHODS: Ten patients from the Sleep Medicine Service of the "Hospital Geral Sanatório" (Maceió, Alagoas, Brazil) were diagnosed with EDS, and a personalised MAD was made for each one of them. Nocturnal polysomnography (NPSG) and maintenance of wakefulness test (MWT) were applied before (baseline) and 3 months after the continuous use of the MAD. The number of arousals and micro-arousals at baseline and after treatment was also evaluated. RESULTS: All 10 patients completed the investigation. A significant decrease in the number of arousals and micro-arousals per night of sleep was observed after the use of MAD for three consecutive months (P = 0.0078; Wilcoxon signed-rank test). Also, there was a significant reduction on the apnoea/hypopnea index between baseline and post-treatment values (P = 0.0001; paired t test), as well as an increase in the mean latency for the onset of sleep (MSL) in the MTW (P = 0.0047; paired t test), indicating a significant difference among baseline and after treatment. CONCLUSION: We conclude that the improvement on EDS is associated with the used of MAD in patients diagnosed with OSA, improving their quality of sleep.

Association between mandibular advancement device therapy and reduction of Excessive Daytime Sleepiness due to Obstructive Sleep Apnea.

BACKGROUND: Excessive daytime sleepiness is frequently reported as a symptom for OSA, leading to problems with concentration, mood and memory. MAD are considered as an effective therapy to control OSA, reducing EDS and improving sleep quality. OBJECTIVES: The present study aimed to investigate the effects of mandibular advance device (MAD) therapy on excessive daytime sleepiness (EDS) of patients diagnosed with obstructive sleep apnea (OSA). METHODS: Ten patients from the Sleep Medicine Service of the "Hospital Geral Sanatório" (Maceió, Alagoas, Brazil) were diagnosed with EDS, and a personalized MAD was made for each one of them. Nocturnal polysomnography (NPSG) and Maintenance of wakefulness test (MWT) were applied before (baseline) and three months after the continuous use of the MAD. The number of arousals and microarousals at baseline and after treatment were also evaluated. RESULTS: All 10 patients completed the investigation. A significant decrease in the number of arousals and microarousals per night of sleep was observed after the use of MAD for three consecutive months (P=0.0078; Wilcoxon signed-ranks test). Also, there was a significant reduction on the apnea/hypopnea index between baseline and post-treatment values (P=0.0001; paired-t test), as well as an increase in the mean latency for the onset of sleep (MSL) in the MTW (P=0.0047; paired t- test), indicating a significant difference among baseline and after treatment. CONCLUSION: We conclude that the improvement on EDS is associated with the used of MAD in patients diagnosed with OSA, improving their quality of sleep. This article is protected by copyright. All rights reserved.

How fast can treatment with overdentures improve the masticatory function and OHRQoL of atrophic edentulous patients? A 1-year longitudinal clinical study.

OBJECTIVES: The aim of this prospective clinical study was to evaluate the masticatory function (MF) and subjective perception of patients with poor denture-bearing tissue in relation to change and the time required to identify an improvement in these parameters after rehabilitation with mandibular overdentures (MO) by two narrow-diameter two-piece implants. MATERIAL AND METHODS: Twenty-three edentulous patients were selected for MO installation. The masticatory function (MF) was evaluated with the masticatory performance (MP) and swallowing threshold (ST) tests. In the MP test, each volunteer was instructed to masticate a portion of Optocal (standardized artificial test food) for 40 masticatory cycles. During the swallowing threshold test, the patients were instructed to chew a new portion of Optocal cubes until they felt the desire to swallow. The MF tests were performed while complete denture (CD) wearers (baseline) and 1, 3, 6, and 12 months after MO loading. In addition, the subjective perception was assessed through the questionnaires Dental Impact on Daily Living (DIDL), Geriatric Oral Health Assessment Index (GOHAI), and Oral Health Impact Profile in Edentulous (OHIP- EDENT) at the baseline and 3, 6, and 12 months after MO loading. RESULTS: A significant improvement in masticatory function (p < .05) was observed already in the first month of loading. Three months after MO loading, a significant improvement (p < .05) was found in the subjective perception of patients. The effect size indicates that the MO had the greatest impact on the domains related to function and comfort of all questionnaires and in relation to psychosocial domain of the GOHAI. The level of patient satisfaction increased significantly after the MO loading and reached >90% satisfied patients at 12 months. CONCLUSION: The MO improved both the MF of the patient and their oral health-related quality of life and satisfaction regarding the prosthesis in a short time period.

Dose-response effect of chlorhexidine on a multispecies oral biofilm formed on pure titanium and on a titanium-zirconium alloy.

This study aimed to test the dose-response effect of chlorhexidine on multispecies biofilms formed on commercially pure titanium (cpTi) and titanium-zirconium (TiZr) alloy. Biofilms were formed on cpTi and TiZr discs and treated two times per day with five different chlorhexidine concentrations (0.12, 0.20, 0.50, 1, 2%). The biofilms were collected for microbiological, biochemical and microscopic analyses. The significance of differences among groups was evaluated by linear regression, ANOVA, Bonferroni and Tukey tests. The mean number of colony-forming units decreased as the chlorhexidine concentration increased for both cpTi and TiZr (p < 0.05). The maximum effect was observed with the 0.5% concentration. Confocal microscopy images suggested an increase in the number of dead bacterial cells with increased chlorhexidine concentration. The biofilm pH increased after chlorhexidine exposure (p < 0.05). Chlorhexidine showed an antimicrobial dose-response effect in controlling biofilm on cpTi and TiZr. 0.5% chlorhexidine can be used to achieve the maximum antimicrobial effect on both materials.

Starch Combined with Sucrose Provokes Greater Root Dentine Demineralization than Sucrose Alone.

Since there is no consensus about whether starch increases the cariogenic potential of sucrose, we used a validated 3-species biofilm model to evaluate if starch combined with sucrose provokes higher root dentine demineralization than sucrose alone. Biofilms (n = 18) composed by Streptococcus mutans (the most cariogenic bacteria), Actinomces naeslundii (which has amylolytic activity), and Streptococcus gordonii (which binds salivary amylase) were formed on root dentine slabs under exposure 8 ×/day to one of the following treatments: 0.9% NaCl, 1% starch, 10% sucrose, or a combination of 1% starch and 10% sucrose. Before each treatment, biofilms were pretreated with human whole saliva for 1 min. The pH of the culture medium was measured daily as an indicator of biofilm acidogenicity. After 96 h of growth, the biofilms were collected, and the biomass, bacteria viability, and polysaccharides were analyzed. Dentine demineralization was assessed by surface hardness loss (% SHL). Biofilm bioarchitecture was analyzed using confocal laser scanning microscopy. Treatment with a starch and sucrose combination provoked higher (p = 0.01) dentine demineralization than sucrose alone (% SHL = 53.2 ± 7.0 vs. 43.2 ± 8.7). This was supported by lower pH values (p = 0.007) of the culture medium after daily exposure to the starch and sucrose combination compared with sucrose (4.89 ± 0.29 vs. 5.19 ± 0.32). Microbiological and biochemical findings did not differ between biofilms treated with the combination of starch and sucrose and sucrose alone (p > 0.05). Our findings give support to the hypothesis that a starch and sucrose combination is more cariogenic for root dentine than sucrose alone.

Prevalence of psychosocial impairment in temporomandibular disorder patients: A systematic review.

BACKGROUND: Several studies have described high levels of psychosocial disorders in patients with temporomandibular disorders (TMD), but an estimate of their prevalence in populations of TMD patients has never been assessed systematically. OBJECTIVE: To conduct a systematic review of the literature on the prevalence of research diagnostic criteria for TMD (RDC/TMD) Axis II findings in TMD patients. METHODS: Search for articles was carried out by two independent researchers to retrieve papers published after 1992. Inclusion was reserved to observational studies with a minimum sample size of 100 individuals, which used RDC/TMD diagnostic protocol. Quality assessment was performed with the adoption of the methodological evaluation of observational research (MORE). RESULTS: A total of 1186 citations were obtained from search strategy, but only 14 filled the inclusion criteria. Included papers reported somatisation, depression and/or pain-related disability prevalence or scores from populations of 12 different countries. A broad range in the prevalence of moderate-to-severe somatisation in patients with TMD was observed, ranging from 28.5% to 76.6%. Similar results were found for depression, with moderate-to-severe levels in 21.4%-60.1% of patients. Finally, most patients were rated as grade I or II of the Graded Chronic Pain Scale, whereas high pain-related impairment was present in 2.6% to 24% of the individuals. CONCLUSION: The prevalence of severe-to-moderate somatisation and depression was high in TMD patients, while severe physical impairment was not commonly reported.

Biomechanical behavior of 2-implant- and single-implant-retained mandibular overdentures with conventional or mini implants.

STATEMENT OF PROBLEM: The use of single or mini dental implants to retain mandibular overdentures is still questionable. PURPOSE: The purpose of this finite element analysis (FEA) study was to investigate the biomechanical behavior of 2- and single-implant-retained mandibular overdentures with conventional or mini implants. MATERIAL AND METHODS: Four 3-dimensional (3D) finite element models were constructed with the following designs of mandibular overdentures: 2 (group 2-C) and single (group 1-C) conventional external hexagon implants with ball or O-ring attachment and 2 (group 2-M) and single (group 1-M) 1-piece mini implants. A 150-N axial load was applied bilaterally and simultaneously on the first molar. Overdenture displacement, von Mises equivalent stress (implants and/or prosthetic components), and maximum principal stresses (peri-implant bone) were recorded numerically and then color-coded and compared among the groups. RESULTS: The overdenture displacement (in mm) was higher for the 1-M (0.16) and 2-M (0.17) groups when compared with 1-C (0.09) and 2-C (0.08). Irrespective of the type of implant, the single-implant groups presented higher values of stress (in MPa) on the implants than did the 2-implant groups (1-C=52.53; 1-M=2.95; 2-C=34.66; 2-M=2.37), ball attachment (1-C=201.33; 2-C=159.06), housing or O-ring (1-C=125.01; 1-M=1.96; 2-C=88.84; 2-M=1.27), and peri-implant cortical bone (1-C=19.37; 1-M=1.47; 2-C=15.70; 2-M=1.06). The mini implant overdentures presented lower stress values on the implants, housing or O-ring, and peri-implant bone than did the conventional implant overdentures, regardless of the number of implants. CONCLUSIONS: The 2-implant-retained overdentures exhibited lower stresses than the single- implant-retained overdentures, irrespective of the type of implant. The mini implants demonstrated higher overdenture displacement and lower stresses than did conventional implant overdentures for single- and 2-implant-retained overdentures.

Effect of 5,000 ppm Fluoride Dentifrice or 1,100 ppm Fluoride Dentifrice Combined with Acidulated Phosphate Fluoride on Caries Lesion Inhibition and Repair.

High fluoride dentifrice (FD; 5,000 ppm F) has been recommended to arrest root dentine lesions and to control enamel caries in high-risk patients. Also, standard FD (1,100 ppm F) in combination with professional fluoride application has been recommended to control dentine caries, but the effect of this combination on enamel has been considered modest. Considering the lack of evaluation comparing the use of 5,000 ppm FD (5,000-FD) versus acidulated phosphate fluoride (APF) application combined with 1,100 ppm FD (1,100-FD) on the inhibition and repair of caries lesions in both enamel and dentine, we conducted this in situ, double-blind, crossover study of 3 phases of 14 days. In each phase, 18 volunteers wore palatal appliances containing enamel and root dentine specimens, either sound or carious, to evaluate the effect of the treatments on the inhibition or repair of caries lesions, respectively. The treatments were non-FD (negative control), 5,000-FD, or 1 APF gel application on dental specimens combined with 1,100-FD used twice per day (APF + 1,100-FD). The reduction of demineralization and enhancement of remineralization were assessed by surface and cross-sectional hardness. Fluoride concentration was determined on dental specimens and on the formed biofilm. For enamel, APF + 1,100-FD and 5,000-FD did not differ regarding the inhibition of demineralization and repair of caries lesions. However, for dentine the difference between these treatments was inconclusive because while APF + 1,100-FD was more effective than 5,000-FD in caries lesion reduction and repair, 5,000-FD was more effective than APF + 1,100-FD in the reduction of surface demineralization. Therefore, the findings show that the combination of APF + 1,100-FD is as effective as 5,000-FD in enamel inhibition of demineralization and enhancement of remineralization.