Impact of profile angle of CAD-CAM abutment on the marginal bone loss of implant-supported single-tooth posterior restorations.

STATEMENT OF PROBLEM: Although the emergence angle has been related to marginal bone loss, information regarding the relationship between the transmucosal configuration of a computer-aided design and computer-aided manufacturing (CAD-CAM) abutment at specific subgingival levels and the amount of marginal bone loss is lacking. PURPOSE: The purpose of this retrospective clinical study was to evaluate the influence of CAD-CAM abutment profile angles, measured at different subgingival positions, on the marginal bone loss of posterior single-tooth implant-supported restorations. MATERIAL AND METHODS: A total of 260 posterior single-tooth implant-supported restorations using CAD-CAM abutments were analyzed in 206 patients. All implants had internal conical seal connections with a platform-switched design. The following data were extracted using digital periapical radiography: emergence profile, profile angle at distance ranges of 0 to 1 mm, 1 to 2 mm, and 2 to 3 mm from the implant-abutment junction, and peri-implant marginal bone loss (MBL). The MBL was measured from the time of delivery of the restorations up to 7 years or more. A linear mixed model was applied to investigate whether there was a significant difference in MBL based on the emergence profile and time, followed by the Bonferroni correction post hoc test. A Pearson correlation analysis was used to analyze the correlation between the profile angle and MBL at each distance range. The cut-off points for each distance range were determined by using the c-index, and independent t tests were conducted based on these cut-off values to evaluate the statistical differences (α=.05 for all statistical analyses). RESULTS: The convex emergence profile exhibited greater MBL than the concave and straight profiles at each follow-up visit (P<.001). A significant correlation was found between the profile angle and MBL in the 0 to 1 mm, 1 to 2 mm distance ranges. However, no significant correlation was found between the profile angle and MBL in the 2 to 3 mm distance range (P>.05). The cut-off points were 34 degrees at the mesial and 28 degrees at the distal in the 0 to 1 mm range, and 33 and 20 degrees at the mesial and distal in the 1 to 2 mm range. CONCLUSIONS: The profile angle near the implant-abutment junction and the type of emergence profile of the CAD-CAM abutment were closely associated with MBL in implants with internal conical seal connection with a platform switch design.

Effect of 150 MeV protons on carbon nanotubes for fabrication of a radiation detector.

High energy and high flux protons are used in proton therapy and the impact of proton radiation is a major reliability concern for electronics and solar cells in low earth orbit as well as in the trapped belts. Carbon nanotubes (CNTs), due to their unique characteristics, have been considered for the construction of proton and other radiation sensors. Here, a single wall CNT based proton sensor was fabricated on FR4 substrate and its response to 150 MeV proton irradiation was studied. The change in the resistance of the nanotubes upon irradiation is exploited as the sensing mechanism and the sensor shows good sensitivity to proton radiation. Proton radiation induces dissociation of ambient oxygen, followed by the adsorption of oxygen species on the nanotube surface, which influences its electrical characteristics. Since the nanotube film is thin and the 150 MeV protons are expected to penetrate into and interact with the substrate, control experiments were conducted to study the impact on FR4 substrate without the nanotubes. The dielectric loss tangent or dissipation factor of FR4 increases after irradiation due to an increase in the cross-linking of the resin arising from the degradation of the polymer network.

Surface Potential-Controlled Oscillation in FET-Based Biosensors.

Field-effect transistor (FET)-based biosensors have garnered significant attention for their label-free electrical detection of charged biomolecules. Whereas conventional output parameters such as threshold voltage and channel current have been widely used for the detection and quantitation of analytes of interest, they require bulky instruments and specialized readout circuits, which often limit point-of-care testing applications. In this study, we demonstrate a simple conversion method that transforms the surface potential into an oscillating signal as an output of the FET-based biosensor. The oscillation frequency is proposed as a parameter for FET-based biosensors owing to its intrinsic advantages of simple and compact implementation of readout circuits as well as high compatibility with neuromorphic applications. An extended-gate biosensor comprising an Al2O3-deposited sensing electrode and a readout transistor is connected to a ring oscillator that generates surface potential-controlled oscillation for pH sensing. Electrical measurement of the oscillation frequency as a function of pH reveals that the oscillation frequency can be used as a sensitive and reliable output parameter in FET-based biosensors for the detection of chemical and biological species. We confirmed that the oscillation frequency is directly correlated with the threshold voltage. For signal amplification, the effects of circuit parameters on pH sensitivity are investigated using different methods, including electrical measurements, analytical calculations, and circuit simulations. An Arduino board to measure the oscillation frequency is integrated with the proposed sensor to enable portable and real-time pH measurement for point-of-care testing applications.

Newly Categorized Seromucinous Tumor of the Ovary: Magnetic Resonance Imaging Findings.

OBJECTIVE: The aim of this study was to describe magnetic resonance imaging findings of newly categorized ovarian seromucinous tumors. METHODS: We retrospectively reviewed the images of 29 patients with seromucinous tumor for the following factors: size, configuration, signal intensity (SI), and accompanying ovarian endometriosis. RESULTS: Thirty-two tumors (17 benign, 7 borderline, 8 carcinoma) were found on computed tomography or magnetic resonance imaging. Their mean size was 11.4 cm. Benign tumors appeared as unilocular or multilocular cystic masses. Borderline tumors and carcinomas appeared as complex cystic-solid masses. T2-weighted SI of the solid portion was hyperintense in borderline tumors and intermediate in carcinomas. Endometriosis was present in 18 tumors, and hemorrhage (on images) in 20. CONCLUSIONS: The imaging features of seromucinous tumors varied by tumor type. More than half of tumors were accompanied by endometriosis. High T2-weighted SI of the solid portion could be a specific feature of borderline tumors. It is hard to differentiate seromucinous carcinomas from other endometriosis-related carcinomas.

Samarium-Doped Indium-Tin-Oxide Electrode for Organic Light-Emitting Devices.

Here in, properties of samarium-doped indium-tin-oxide (ITO:Sm) films deposited by DC-magnetron sputtering, and organic light-emitting devices (OLEDs) using an ITO:Sm film as an anode were investigated. The electrical resistivity of the ITO:Sm films increased with Sm doping. The work function of each ITO:Sm film (5.2-5.7 eV) was higher than that of an ITO film (4.8 eV). The crystal structure of the ITO:Sm films was In2O3-type when the doping ratio of Sm in the film was up to 5 at.%, and the structure was amorphous in more strongly samarium-doped films. The properties of the OLEDs were varied by the doping ratio of samarium in the ITO:Sm electrodes. The OLEDs with the ITO:Sm electrode exhibited higher efficiency than that of an ITO-based control device at the same current density.

Suppression of lung inflammation by the ethanol extract of Chung-Sang and the possible role of Nrf2.

BACKGROUND: Asian traditional herbal remedies are typically a concoction of a major and several complementary herbs. While balancing out any adverse effect of the major herb, the complementary herbs could dilute the efficacy of the major herb, resulting in a suboptimal therapeutic effect of an herbal remedy. Here, we formulated Chung-Sang (CS) by collating five major herbs, which are used against inflammatory diseases, and tested whether an experimental formula composed of only major herbs is effective in suppressing inflammation without significant side effects. METHODS: The 50% ethanol extract of CS (eCS) was fingerprinted by HPLC. Cytotoxicity to RAW 264.7 cells was determined by an MTT assay and a flow cytometer. Nuclear NF-κB and Nrf2 were analyzed by western blot. Ubiquitinated Nrf2 was similarly analyzed following immunoprecipitation of Nrf2. Acute lung inflammation and sepsis were induced in C57BL/6 mice. The effects of eCS on lung disease were measured by HE staining of lung sections, a differential cell counting of bronchoalveolar lavage fluid, a myeloperoxidase (MPO) assay, a real-time qPCR, and Kaplan-Meier survival of mice. RESULTS: eCS neither elicited cytotoxicity nor reactive oxygen species. While not suppressing NF-κB, eCS activated Nrf2, reduced the ubiquitination of Nrf2, and consequently induced the expression of Nrf2-dependent genes. In an acute lung inflammation mouse model, an intratracheal (i.t.) eCS suppressed neutrophil infiltration, the expression of inflammatory cytokine genes, and MPO activity. In a sepsis mouse model, a single i.t. eCS was sufficient to significantly decrease mouse mortality. CONCLUSIONS: eCS could suppress severe lung inflammation in mice. This effect seemed to associate with eCS activating Nrf2. Our findings suggest that herbal remedies consisting of only major herbs are worth considering.

Difference in Midface Rejuvenation Strategy Between East Asians and Caucasians Based on Analysis of Age-related Changes in the Orbit and Midcheek Using Computed Tomography.

BACKGROUND: The differences between Caucasian and East Asian faces could lead to different age-related bony changes. We analyzed computed tomography (CT) scan images of East Asians to find objective differences in midface rejuvenation strategy between East Asians and Caucasians. METHODS: We reviewed 54 East Asian individuals' charts and facial CT images ranging in age-group: Group A (21-30 years), Group B (41-50 years), and Group C (61-70 years). No patients had congenital or acquired facial deformity and history of facial trauma. The anteroposterior length of the orbital roof and floor (LOR, LOF) and the angle of the anterior wall of the maxilla were recorded on parasagittal images through the midline of the orbit. RESULTS: The LORs at their midpoints showed significant differences between Groups A and B (p < 0.01). The LOFs were also significantly different between Groups A and B (p < 0.001). The difference in the angle between the anterior maxillary wall and the orbital floor was not significant between Groups A and B. The lengths between Groups B and C showed no significant differences. CONCLUSION: Our study demonstrated that the aging process in East Asians differs considerably from that in Caucasians, with characteristic significant changes in LOF and LOR. Since the aging process is different, the strategies to cope with aging should also differ. Volume restoration of the inferior orbital rim in the midface is one of the most important rejuvenation methods in East Asians. LEVEL OF EVIDENCE V: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266.

Functional Expression and Characterization of the Recombinant N-Acetyl-Glucosamine/N-Acetyl-Galactosamine-Specific Marine Algal Lectin BPL3.

Lectins, characterized by their carbohydrate-binding ability, have extensive practical applications. However, their industrial use is limited due to impurity. Thus, quality-controlled production of recombinant lectin is necessary. In this study, the algal lectin BPL3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocyte. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled large-scale production of recombinant lectins.

Nanoscale Vacuum Channel Transistor.

Vacuum tubes that sparked the electronics era had given way to semiconductor transistors. Despite their faster operation and better immunity to noise and radiation compared to the transistors, the vacuum device technology became extinct due to the high power consumption, integration difficulties, and short lifetime of the vacuum tubes. We combine the best of vacuum tubes and modern silicon nanofabrication technology here. The surround gate nanoscale vacuum channel transistor consists of sharp source and drain electrodes separated by sub-50 nm vacuum channel with a source to gate distance of 10 nm. This transistor performs at a low voltage (<5 V) and provides a high drive current (>3 microamperes). The nanoscale vacuum channel transistor can be a possible alternative to semiconductor transistors beyond Moore's law.

Direct Measurement of the Diffusion Coefficient of Adhesives from Moisture Distribution in Adhesive Layers Using Near-Infrared Spectroscopy.

In this study, we used near-infrared spectroscopy to measure the moisture penetration in epoxy adhesives and investigated the difference in the diffusion coefficients between the bulk and the adhesive layer. Moisture diffusion was evaluated under 100% RH and water immersion conditions. First, the effects of the curing agents and additives on moisture diffusion in the bulk were gravimetrically evaluated using epoxy-coated quartz glass plates. Different diffusion behaviors were observed depending on the curing agent used. The presence of additives resulted in higher diffusion coefficients, whereas the overall moisture content was low. Next, the moisture distribution in the adhesive layer was visualized using a specimen sandwiched between the quartz glass plates, and the diffusion coefficient of the adhesive layer was calculated. The diffusion coefficient in the adhesive layer was larger than that in the bulk. For adhesives cured with hydrophobic diamine, the diffusion coefficient within the adhesive layer increased by approximately 1.5 times compared with that in the bulk, regardless of the exposure environment. The adhesive, composed of a resin, Dicyandiamide, and additives, showed a 2-fold increase in the diffusion coefficient under high-humidity exposure conditions but no significant change under the water immersion condition. Therefore, these results suggest that, for an accurate analysis of moisture distribution, it is important to measure the diffusion coefficient of the adhesive layer directly rather than using the diffusion coefficient of the material itself.

Cloning, heterologous expression, and enzymatic characterization of cathepsin L from starfish (Asterina pectinifera).

To determine the role of cathepsin L in Echinoderms, starfish (Asterina pectinifera) cathepsin L (ApCtL) was cloned. The results of RT-PCR analysis indicated that the expression of ApCtL in all of the tissues. The pro-mature enzyme of ApCtL, proApCtL, was expressed in Escherichia coli, and cathepsin activity was detected by cleaving of synthetic fluorogenic peptide substrates and gelatin zymography.

Characteristics of Al-doped ZnO films grown by atomic layer deposition for silicon nanowire photovoltaic device.

We report the structural, electrical, and optical characteristics of Al-doped ZnO (ZnO:Al) films deposited on glass by atomic layer deposition (ALD) with various Al2O3 film contents for use as transparent electrodes. Unlike films fabricated by a sputtering method, the diffraction peak position of the films deposited by ALD progressively moved to a higher angle with increasing Al2O3 film content. This indicates that Zn sites were effectively replaced by Al, due to layer-by-layer growth mechanism of ALD process which is based on alternate self-limiting surface chemical reactions. By adjusting the Al2O3 film content, a ZnO:Al film with low electrical resistivity (9.84 x 10(-4) Omega cm) was obtained at an Al2O3 film content of 3.17%, where the Al concentration, carrier mobility, optical transmittance, and bandgap energy were 2.8 wt%, 11.20 cm2 V(-1) s(-1), 94.23%, and 3.6 eV, respectively. Moreover, the estimated figure of merit value of our best sample was 8.2 m7Omega(-1). These results suggest that ZnO:Al films deposited by ALD could be useful for electronic devices in which especially require 3-dimensional conformal deposition of the transparent electrode and surface passivation.

Transformable functional nanoscale building blocks with wafer-scale silicon nanowires.

Through the fusion of electrostatics and mechanical dynamics, we demonstrate a transformable silicon nanowire (SiNW) field effect transistor (FET) through a wafer-scale top-down approach. By felicitously taking advantage of the proposed electrostatic SiNW-FET with mechanically movable SiNWs, all essential logic gates, including address decoders, can be monolithically integrated into a single device. The unification of various functional devices, such as pn-diodes, FETs, logic gates, and address decoders, can therefore eliminate the complex fabrication issues associated with nanoscale integration. These results represent a step toward the creation of multifunctional and flexible nanoelectronics.

On-State Current Degradation Owing to Displacement Defect by Terrestrial Cosmic Rays in Nanosheet FET.

Silicon displacement defects are caused by various effects. For instance, epitaxial crystalline silicon growth and ion implantation often result in defects induced by the fabrication process, whereas displacement damage is induced by terrestrial cosmic radiation. Clustered displacement damage reportedly reduces the on-state current (Ion) in ordinary MOSFETs. In the case of an extremely scaled device such as a nanosheet field-effect transistor (NS-FET), the impact of displacement defect size was analyzed on the basis of the NS dimensions related to the device characteristics. In this study, we investigated the effect of displacement defects on NS-FETs using technology computer-aided design; the simulation model included quantum transport effects. The geometrical conditions, temperatures, trap concentrations, and scattering models were considered as the variables for on-state current reduction.

Double-gate nanowire field effect transistor for a biosensor.

A silicon nanowire field effect transistor (FET) straddled by the double-gate was demonstrated for biosensor application. The separated double-gates, G1 (primary) and G2 (secondary), allow independent voltage control to modulate channel potential. Therefore, the detection sensitivity was enhanced by the use of G2. By applying weakly positive bias to G2, the sensing window was significantly broadened compared to the case of employing G1 only, which is nominally used in conventional nanowire FET-based biosensors. The charge effect arising from biomolecules was also analyzed. Double-gate nanowire FET can pave the way for an electrically working biosensor without a labeling process.

A nanoscale vacuum field emission gated diode with an umbrella cathode.

A nanoscale field emission vacuum channel gated diode structure is proposed and a tungsten cathode with an umbrella-like geometry and sharp vertical edge is fabricated. The edge of the suspended cathode becomes the field emission surface. Unlike in the traditional transistor with the gate typically located between the source and the drain, the bottom silicon plate becomes the gate here and the anode terminal is located between the umbrella cathode and the gate. The fabricated devices show excellent diode characteristics and the gated diode structure is attractive for extremely low gate leakage.

Printable Gel Polymer Electrolytes for Solid-State Printed Supercapacitors.

Supercapacitors prepared by printing allow a simple manufacturing process, easy customization, high material efficiency and wide substrate compatibility. While printable active layers have been widely studied, printable electrolytes have not been thoroughly investigated despite their importance. A printable electrolyte should not only have high ionic conductivity, but also proper viscosity, small particle size and chemical stability. Here, gel-polymer electrolytes (GPE) that are compatible with printing were developed and their electrochemical performance was analyzed. Five GPE formulations based on various polymer-conductive substance combinations were investigated. Among them, GPE made of polyvinylidene difluoride (PVDF) polymer matrix and LiClO4 conductive substance exhibited the best electrochemical performance, with a gravimetric capacitance of 176.4 F/g and areal capacitance of 152.7 mF/cm2 at a potential scan rate of 10 mV/s. The in-depth study of the in-plane solid-state supercapacitors based on various printed GPEs suggests that printable electrolytes provide desirable attributes for high-performance printed energy devices such as supercapacitors, batteries, fuel cells and dye-sensitized solar cells.

The Effects of Mindfulness-Based Mandala Coloring, Made in Nature, on Chronic Widespread Musculoskeletal Pain: Randomized Trial.

This study aimed to investigate the effects of mindfulness-based mandala coloring made within nature on individuals with chronic widespread musculoskeletal pain (CWP). Thirty-six participants were randomly allocated. In the experimental group, identical interventions and procedures were administered for each experiment. The control group members were untreated and remained in an urban environment. Overall, the experiment showed significant improvements in tender points (f = 8.791, p = 0.006), total stress level (f = 14.570, p = 0.001), depressive symptoms (f = 15.205, p = 0.001), anger symptoms (f = 7.263, p = 0.011) and salivary cortisol (f = 10.619, p = 0.003) in the experimental group. The results reflect that MBMC within nature is effective in reducing pain, psychological stress responses, and cortisol levels in individuals with CWP. The positive results could be a product of the experimental design rather than the treatment itself. A rigorous experimental design provides better understanding of MBMC within nature.

A novel subdermal anchoring technique for the effective treatment of congenital melanocytic nevus using de-epithelialized dermal flaps.

BACKGROUND: In patients with congenital melanocytic nevus (CMN), single-stage removal of large lesions can be difficult because the high tension created by excising and repairing a large lesion may result in scar widening. Herein, we introduce a method to effectively excise lesions while minimizing scarring and compare its outcomes to those of existing surgical methods. METHODS: We compared patients who underwent surgery using the anchoring technique (n=42) or the conventional elliptical technique (n=36). One side of the lesion was removed via en bloc resection up to the superficial fascia. The other side of the lesion was removed via de-epithelialization. The de-epithelialized dermal flap was then fixed by suturing it to the superficial fascia on the opposite side. The length of the lesion's long axis and amount of scar widening were measured immediately after surgery and at 2, 6, and 12 months postoperatively. At 12 months, patients were assessed using the Patient and Observer Scar Assessment Scale. RESULTS: The lesion locations included the face, arms, legs, back, and abdomen. The anchoring method resulted in shorter and smaller scars than the conventional method. There were no cases of postoperative hematoma or wound dehiscence. Significant differences in postoperative scar widening were found in the arm and leg areas (P<0.05). CONCLUSIONS: The anchoring method introduced in this study can provide much better outcomes than the conventional method. The anchoring method is particularly useful for the removal of CMN around the joints or extremities, where the surgical site is subjected to high tension.

All 3D-Printed Flexible ZnO UV Photodetector on an Ultraflat Substrate.

An all three-dimensional (3D)-printed flexible ZnO ultraviolet (UV) photodetector is demonstrated, where the 3D-printing method is used not only for the electrode and photosensitive material but also for creating a substrate. An ultraflat and flexible substrate capable of serving as the backbone layer is developed using a water-dissolvable polymer layer for surface planarization. A two-layered printing followed by surface treatment is demonstrated for the substrate preparation. As mechanical support but flexible, a thick and sparse thermoplastic polyurethane layer is printed. On its surface, a thin and dense poly(vinyl alcohol) (PVA) is then printed. A precise control of PVA reflow using a microwater droplet results in a flexible and extremely uniform substrate. A Cu-Ag nanowire network is directly 3D printed on the flexible substrate for the conducting layer, followed by ZnO for the photosensitive material. Unlike the planar two-dimensional printing that provides thin films, 3D printing allows the electrode to have a step height, which can be made like a dam to accommodate a thick film of ZnO. Photosensitivity as a function of various ZnO thickness values was investigated to establish an optimal thickness for UV response. The device was also tested in natural sunlight along with stability and reliability.