Improvement of Dynamic Performance and Detectivity in Near-Infrared Colloidal Quantum Dot Photodetectors by Incorporating Conjugated Polymers.

Colloidal quantum dots (CQDs) have a unique advantage in realizing near-infrared (NIR) photodetection since their optical properties are readily tuned by the particle size, but CQD-based photodetectors (QPDs) presently show a high dark current density (Jd) and insufficient dynamic characteristics. To overcome these two problems, we synthesized and introduced two types of conjugated polymers (CPs) by replacing the p-type CQD layer in the QPDs. The low dielectric constant and insulating properties of CPs under dark conditions effectively suppressed the Jd in the QPDs. In addition, the energy-level alignment and high-hole mobility of the CPs facilitated hole transport. Therefore, both the responsivity and specific detectivity were highly enhanced in the CP-based QPDs. Notably, the dynamic characteristics of the QPDs, such as the -3 dB cut-off frequency and rising/falling response times, were significantly improved in the CP-based QPDs owing to the sizable molecular ordering and fast hole transport of the CP in the film state as well as the low trap density, well-aligned energy levels, and good interfacial contact in the CP-based devices.

Interfacial Modifier Having Julolidine for the Cathode Buffer Layer in PTB-7:PC70BM Based Inverted Organic Photovoltaic Cells.

The julolidine based interfacial modifier (IM-J) for cathode buffer layer following the "donor-acceptor" design concept with julolidine substituent as an electron donating moiety was incoporated to improve the surface properties of ZnO. Simple treatment of metal oxide type cathode buffer materials with organic interfacial modifier induces the enhanced photovoltaic performance and could effectively overcome several interfacial problems in inverted organic photovoltaic cells (I-OPVs). We studied on the coverage of IM-J on ZnO surface with variation of solution concentrations to reduce charge recombination and macroscopic phase separation. At the optimum condition, ZnO/IM-J (0.05 w/v%), IM-J significantly decreased the surface tension (46.1 mN/m) and improved surface morphology (RMS roughness: 0.61 nm). As a result, compared to the unmodified ZnO based device, the ZnO/IM-J based I-OPVs showed significantly improved power conversion efficiency (PCE) from 7.41 to 8.07% due to the increased photocurrent density (Jsc) and fill factor (FF). It is concluded that IM-J is one of the promising candidates for controlling electronic property of ZnO buffer layer in inverted organic photovoltaic cells. Also, our interfacial modified system can be utilized in other optoelectronic devices.

Edge-on gating effect in molecular wires.

This work demonstrates edge-on chemical gating effect in molecular wires utilizing the pyridinoparacyclophane (PC) moiety as the gate. Different substituents with varied electronic demands are attached to the gate to simulate the effect of varying gating voltages similar to that in field-effect transistor (FET). It was observed that the orbital energy level and charge carrier's tunneling barriers can be tuned by changing the gating group from strong electron acceptors to strong electron donors. The single molecule conductance and current-voltage characteristics of this molecular system are truly similar to those expected for an actual single molecular transistor.

Effect of acceptor strength on optical and electronic properties in conjugated polymers for solar applications.

Four new low-bandgap electron-accepting polymers-poly(4,10-bis(2-butyloctyl)-2-(2-(2-ethylhexyl)-1,1-dioxido-3-oxo-2,3-dihydrothieno[3,4-d]isothiazol-4-yl)thieno[2',3':5,6]pyrido[3,4-g]thieno[3,2-c]isoquinoline-5,11(4H,10H-dione) (PNSW); poly(4,10-bis(2-butyloctyl)-2-(5-(2-ethylhexyl)-4,6-dioxo-5,6-dihydro-4H-thieno[3,4-c]pyrrol-1-yl)thieno[2',3':5,6]pyrido[3,4-g]thieno[3,2-c]isoquinoline-5,11(4H,10H)-dione) (PNTPD); poly(5-(4,10-bis(2-butyloctyl)-5,11-dioxo-4,5,10,11-tetrahydrothieno[2',3':5,6]pyrido[3,4-g]thieno[3,2-c]isoquinolin-2-yl)-2,9-bis(2-decyldodecyl)anthra[2,1,9-def:6,5,10-d'e'f']diisoquinoline-1,3,8,10(2H,9H)-tetraone) (PNPDI); and poly(9,9-bis(2-butyloctyl)-9H-fluorene-bis((1,10:5,6)2-(5,6-dihydro-4H-cyclopenta[b]thiophene-4-ylidene)malonitrile)-2-(2,3-dihydrothieno[3,4-b][1,4]dioxine)) (PECN)-containing thieno[2',3':5',6']pyrido[3,4-g]thieno[3,2-c]isoquinoline-5,11(4H,10H)-dione and fluorenedicyclopentathiophene dimalononitrile, were investigated to probe their structure-function relationships for solar cell applications. PTB7 was also investigated for comparison with the new low-bandgap polymers. The steady-state, ultrafast dynamics and nonlinear optical properties of all the organic polymers were probed. All the polymers showed broad absorption in the visible region, with the absorption of PNPDI and PECN extending into the near-IR region. The polymers had HOMO levels ranging from -5.73 to -5.15 eV and low bandgaps of 1.47-2.45 eV. Fluorescence upconversion studies on the polymers showed long lifetimes of 1.6 and 2.4 ns for PNSW and PNTPD, respectively, while PNPDI and PECN showed very fast decays within 353 and 110 fs. PECN exhibited a very high two-photon absorption cross section. The electronic structure calculations of the repeating units of the polymers indicated the localization of the molecular orbitals in different co-monomers. As the difference between the electron affinities of the co-monomers in the repeating units decreases, the highest occupied and lowest unoccupied molecular orbitals become more distributed. All the measurements suggest that a large difference in the electron affinities of the co-monomers of the polymers contributes to the improvement of the photophysical properties necessary for highly efficient solar cell performance. PECN exhibited excellent photophysical properties, which makes it to be a good candidate for solar cell device applications.

Synthesis and characterization of an anthracene-based low band gap polymer for photovoltaic devices.

We have synthesized an anthracene-based conjugated polymer, poly[(9,10-bis(oct-1-ynyl)anthracene)-alt-(5,6-bis(octyloxy)-4,7-bis(thiophen-2-yl)benzo-[c][1,2,5]-thiadiazole)] (PANTBT), for application in organic photovoltaic devices. It exhibited a number average molecular weight of 14,300 g/mol and was fairly soluble in chlorinated organic solvents due to flexible octynyl- and octyloxy side chains on the anthracene and benzothiadiazole moieties. PANTBT showed absorption covering 300-660 nm. Through the bond alternation between the electron-sufficient anthracene (and thiophene) and electron-deficient benzothiadiazole units, a band gap of PANTBT was decreased to 1.89 eV, showing a deep HOMO level of -5.31 eV. As a result, PANTBT exhibited promising photovoltaic properties with a PCE value of 1.90% (VOC = 0.77 V, JSC = -6.50 mA/cm2, FF = 0.38) upon blending with PC71, BM under AM 1.5G.

The role of N-doped multiwall carbon nanotubes in achieving highly efficient polymer bulk heterojunction solar cells.

This paper reports an improved solar cell performance of 8.6% by incorporation of N-doped multiwall carbon nanotubes (N-MCNTs) into BHJ solar cells composed of PTB7 and PC71BM. It was demonstrated for the first time that incorporation of N-MCNTs leads to not only increased nanocrystallite sizes but also smaller phase-separated domain sizes of both PTB7 copolymers and PC71BM from X-ray scattering study. The results show that N-MCNTs could serve as both exciton dissociation centers and charge transfer channels. The enhanced charge dissociation probabilities and effective charge carrier lifetime in the active layer material offer evidence to support the conclusion that N-MCNTs facilitated charge separation and transport.

Self-Assembled Monolayer-Based Hole-Transporting Materials for Perovskite Solar Cells.

Ever since self-assembled monolayers (SAMs) were adopted as hole-transporting layers (HTL) for perovskite solar cells (PSCs), numerous SAMs for HTL have been synthesized and reported. SAMs offer several unique advantages including relatively simple synthesis, straightforward molecular engineering, effective surface modification using small amounts of molecules, and suitability for large-area device fabrication. In this review, we discuss recent developments of SAM-based hole-transporting materials (HTMs) for PSCs. Notably, in this article, SAM-based HTMs have been categorized by similarity of synthesis to provide general information for building a SAM structure. SAMs are composed of head, linker, and anchoring groups, and the selection of anchoring groups is key to design the synthetic procedure of SAM-based HTMs. In addition, the working mechanism of SAM-based HTMs has been visualized and explained to provide inspiration for finding new head and anchoring groups that have not yet been explored. Furthermore, both photovoltaic properties and device stabilities have been discussed and summarized, expanding reader's understanding of the relationship between the structure and performance of SAMs-based PSCs.

Switchable Design of Redox-Enhanced Nonaromatic Quinones Enabled by Conjugation Recovery.

An innovative switchable design strategy for modulating the electronic structures of quinones is proposed herein, leading to remarkably enhanced intrinsic redox potentials by restoring conjugated but nonaromatic backbone architectures. Computational validation of two fundamental hypotheses confirms the recovery of backbone conjugation and optimal utilization of the inductive effect in switched quinones, which affords significantly improved redox chemistry and overall performance compared to reference quinones. Geometric and electronic analyses provide strong evidence for the restored backbone conjugation and nonaromaticity in the switched quinones, while highlighting the reinforcement of the inductive effect and suppression of the resonance effect. This strategic approach facilitates the development of an exceptional quinone, viz. 2,6-naphthoquinone, with outstanding performance parameters (338.9 mAh g-1 and 912.9 mWh g-1). Furthermore, 2,6-anthraquinone with superior cyclic stability, demonstrates comparable performance (257.4 mAh g-1 and 702.8 mWh g-1). These findings offer valuable insights into the design of organic cathode materials with favorable redox chemistry in secondary batteries.

Vertically Phase Separated Photomultiplication Organic Photodetectors with p-n Heterojunction Type Ultrafast Dynamic Characteristics.

Photomultiplication (PM)-type organic photodetectors (OPDs), which typically form a homogeneous distribution (HD) of n-type dopants in a p-type polymer host (HD PM-type OPDs), have achieved a breakthrough in device responsivity by surpassing a theoretical limit of external quantum efficiency (EQE). However, they face limitations in higher dark current and slower dynamic characteristics compared to p-n heterojunction (p-n HJ) OPDs due to inherent long lifetime of trapped electrons. To overcome this, a new PM-type OPD is developed that demonstrates ultrafast dynamic properties through a vertical phase separation (VPS) strategy between the p-type polymer and n-type acceptor, referred to as VPS PM-type OPDs. Notably, VPS PM-type OPDs show three orders of magnitude increase in -3 dB cut-off frequency (120 kHz) and over a 200-fold faster response time (rising time = 4.8 µs, falling time = 8.3 µs) compared to HD PM-type OPDs, while maintaining high EQE of 1121% and specific detectivity of 2.53 × 1013 Jones at -10 V. The VPS PM-type OPD represents a groundbreaking advancement by demonstrating the coexistence of p-n HJ and PM modes within a single photoactive layer for the first time. This innovative approach holds the potential to enhance both static and dynamic properties of OPDs.

Advancing Fab-Compatible Color-Selective Organic Photodiodes: Tailored Molecular Design and Nanointerlayers.

High-performance organic photodiodes (OPDs) and OPD-based image sensors are primarily realized using solution processes based on various additives and coating methods. However, vacuum-processed OPDs, which are more compatible with large-scale production, have received little attention, thereby hindering their integration into advanced systems. This study introduces innovations in the material and device structures to prepare superior vacuum-processed OPDs for commercial applications. A series of vacuum-processable, low-cost p-type semiconductors is developed by introducing an electron-rich cyclopentadithiophene core containing various electron-accepting moieties to fine-tune the energy levels without any significant structural or molecular weight changes. An additional nanointerlayer strategy is used to control the crystalline orientation of the upper-deposited photoactive layer, compensating for device performance reduction in inverted, top-illuminated OPDs. These approaches yielded an external quantum efficiency of 70% and a specific detectivity of 2.0 × 1012 Jones in the inverted structures, which are vital for commercial applications. These OPDs enabled visible-light communications with extremely low bit error rates and successful X-ray image capture.

Development of Benzobisoxazole-Based Novel Conjugated Polymers for Organic Thin-Film Transistors.

Benzo[1,2-d:4,5-d']bis(oxazole) (BBO) is a heterocyclic aromatic ring composed of one benzene ring and two oxazole rings, which has unique advantages on the facile synthesis without any column chromatography purification, high solubility on the common organic solvents and planar fused aromatic ring structure. However, BBO conjugated building block has rarely been used to develop conjugated polymers for organic thin film transistors (OTFTs). Three BBO-based monomers, BBO without π-spacer, BBO with non-alkylated thiophene π-spacer and BBO with alkylated thiophene π-spacer, were newly synthesized and they were copolymerized with a strong electron-donating cyclopentadithiophene conjugated building block to give three p-type BBO-based polymers. The polymer containing non-alkylated thiophene π-spacer showed the highest hole mobility of 2.2 × 10-2 cm2 V-1 s-1, which was 100 times higher than the other polymers. From the 2D grazing incidence X-ray diffraction data and simulated polymeric structures, we found that the intercalation of alkyl side chains on the polymer backbones was crucial to determine the intermolecular ordering in the film states, and the introduction of non-alkylated thiophene π-spacer to polymer backbone was the most effective to promote the intercalation of alkyl side chains in the film states and hole mobility in the devices.

Quantification of polystyrene microsphere attachment probability at the oil‒water interface using a microfluidic platform.

This study investigates the effects of interparticle interactions and wettability on the particle attachment efficacy to the oil‒water interface. Three types of PS particles with different surface functional groups were examined at varying salt concentrations and the number of particles injected into the interface. Based on the microfluidic method and the surface coverage measurement, we found that the two contributing factors significantly influenced particle attachment efficiency to the interface, while the wettability factor has a major contribution. This research contributes to the understanding of physicochemical aspects of particle assembly at fluid interfaces and can offer strategies for forming tailored structures with desired interfacial properties.

Development of Alkylthiazole-Based Novel Thermoelectric Conjugated Polymers for Facile Organic Doping.

In this study, we developed two novel conjugated polymers that can easily be doped with F4TCNQ organic dopants using a sequential doping method and then studied their organic thermoelectric (OTE) properties. In particular, to promote the intermolecular ordering of OTE polymers in the presence of the F4TCNQ dopant, alkylthiazole-based conjugated building blocks with highly planar backbone structures were synthesized and copolymerized. All polymers showed strong molecular ordering and edge-on orientation in the film state, even in the presence of the F4TCNQ organic dopant. Thus, the sequential doping process barely changed the molecular ordering of the polymer films while making efficient molecular doping. In addition, the doping efficiency was improved in the more π-extended polymer backbones with thienothiophene units due to the emptier space in the polymer lamellar structure to locate ionized F4TCNQ. Moreover, the study of organic thin-film transistors (OTFTs) revealed that higher hole mobility in OTFTs was the key to increasing the electrical conductivity of OTE devices fabricated using the sequential doping method.

Development of n-Type Small-Molecule Acceptors for Low Dark Current Density and Fast Response Organic Photodetectors.

Suppressing the dark current density (Jd) while maintaining sufficient charge transport is important for improving the specific detectivity (D*) and dynamic characteristics of organic photodetectors (OPDs). In this study, we synthesized three novel small-molecule acceptors (SMAs) densely surrounded by insulating alkyl side chains to minimize the Jd in OPDs. Introducing trialkylated N-annulated perylene diimide as a terminal moiety to the alkylated π-conjugated core structure was highly efficient in suppressing Jd in the devices, resulting in an extremely low Jd of 4.60 × 10-11 A cm-2 and 10-100 times improved D* values in the devices. In addition, SMAs with a geometrically aligned backbone structure exhibited better intermolecular ordering in the blended films, resulting in 3-10 times as high responsivity (R) values in the OPDs. Outstanding OPD performances with a D* of 8.09 × 1012 Jones, -3 dB cutoff frequency of 205.2 kHz, and rising response time of 16 µs were achieved under a 530 nm illumination in photoconductive mode. Geometrically aligned core-terminal SMAs densely surrounded by insulating alkyl side chains are promising for improving the static and dynamic properties of OPDs.

Fabrication of Partially Etched Polystyrene Nanoparticles.

Non-spherical polymer nanoparticles (NPs) have gained attention in various fields, but their fabrication remains challenging. In this study, we present a simple protocol for synthesizing partially etched polystyrene (PS) nanoparticles through emulsion polymerization and chemical etching. By adjusting the degree of crosslinking, we selectively dissolve the weakly crosslinked portions of the particles, resulting in partially etched PS NPs with increased surface area. These partially etched NPs are evaluated for their use as solid surfactants in Pickering emulsions, where they demonstrate significantly improved emulsion stability compared to intact spherical NPs. Our results contribute to the field of nanoparticle shape control and provide insights into developing novel materials for various applications, particularly in the area of solid surfactant usage. Additionally, the importance of conducting cellular toxicity studies using these partially etched NPs for future work is also emphasized.

Cationic conjugated polyelectrolytes-triggered conformational change of molecular beacon aptamer for highly sensitive and selective potassium ion detection.

We demonstrate highly sensitive and selective potassium ion detection against excess sodium ions in water, by modulating the interaction between the G-quadruplex-forming molecular beacon aptamer (MBA) and cationic conjugated polyelectrolyte (CPE). The K(+)-specific aptamer sequence in MBA is used as the molecular recognition element, and the high binding specificity of MBA for potassium ions offers selectivity against a range of metal ions. The hairpin-type MBA labeled with a fluorophore and quencher at both termini undergoes a conformational change (by complexation with CPEs) to either an open-chain form or a G-quadruplex in the absence or presence of K(+) ions. Conformational changes of MBA as well as fluorescence (of the fluorophore in MBA) quenching or amplification via fluorescence resonance energy transfer from CPEs provide clear signal turn-off and -on in the presence or absence of K(+). The detection limit of the K(+) assays is determined to be ~1.5 nM in the presence of 100 mM Na(+) ions, which is ~3 orders of magnitude lower than those reported previously. The successful detection of 5'-adenosine triphosphate (ATP) with the MBA containing an ATP-specific aptamer sequence is also demonstrated using the same sensor scheme. The scheme reported herein is applicable to the detection of other kinds of G-rich aptamer-binding chemicals and biomolecules.

Simple-Structured Low-Cost Dopant-Free Hole-Transporting Polymers for High-Stability CsPbI2Br Perovskite Solar Cells.

Among the solution-processed devices, perovskite solar cells (PSCs) exhibit the highest power conversion efficiency (PCE) of over 25%; tremendous efforts are being undertaken to improve their stability. Recently, all-inorganic CsPbI2Br-based PSCs were reported to exhibit a significantly improved device stability, with a promising PCE of up to 16.79%. In this study, we report stable all-inorganic PSCs by incorporating novel dopant-free hole-transporting materials (HTMs). The synthesis strategy of the newly synthesized polymeric HTMs was similar to that of 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (spiro-OMeTAD), with the exception that they were designed to exhibit dopant-free characteristics. In particular, their polymeric backbone structure was significantly simpler than that of spiro-OMeTADs, and they were easily synthesized in two steps from commercially available chemicals, with an overall yield of ∼50%. The cost of synthesis at the laboratory scale was calculated to be at least 2.4 times cheaper than that of spiro-OMeTADs. The PCE of dopant-free HTM-based PSCs was 11.01%, which is 1.5 times higher than that of the dopant-free spiro-OMeTAD-based devices (7.52%) and comparable to that of the doped spiro-OMeTAD-based devices (12.22%). Notably, the stability of the device based on our dopant-free HTM to atmospheric oxygen and moisture as well as heat and light irradiation was superior to that of devices based on doped and dopant-free spiro-OMeTAD HTMs. On consideration of the synthesis cost, device efficiency, and device stability, our dopant-free HTM is highly promising for all-inorganic PSCs.

Enhanced Static and Dynamic Properties of Highly Miscible Fullerene-Free Green-Selective Organic Photodetectors.

We developed p-n junction organic photodetectors (OPDs) composed of a polymer donor and a nonfullerene acceptor (NFA) to increase both the responsivity (R) and detectivity (D*) while maintaining a narrow wavelength selectivity. The selection of the polymer donor and NFA with similar green (G) absorption is important for achieving G-wavelength selectivity in these OPDs, which differentiates them from current fullerene-based OPDs and NFA-based panchromatic absorption OPDs. In addition, mixing the polymer donor and asymmetric NFA was efficient toward increasing the miscibility and decreasing the interfacial energy difference of the blended films, resulting in the formation of a uniform and well-mixed nanomorphology in the photoconductive layer. Two-dimensional (2D) grazing incidence X-ray diffraction and Fourier-transform infrared spectroscopy revealed that the lamellar ordering of the polymer donor was enhanced in the blend film prepared with an asymmetric NFA, whereas the aggregation of a symmetric NFA in the blend films did not increase the lamellar ordering of the polymer donor. Consequently, we achieved an R value of 0.31 A/W and D* value of 2.0 × 1013 Jones with a full width at half-maximum value of 230 nm at -2 V and fast response time of 27 µs without any external bias in the asymmetric NFA-based OPDs. The enhancement in the lamellar ordering and miscibility of the blended films are crucial toward increasing the static and dynamic properties of OPDs.

Synthesis and photovoltaic properties of cyclopentadithiophene-based low-bandgap copolymers that contain electron-withdrawing thiazole derivatives.

We have synthesized four types of cyclopentadithiophene (CDT)-based low-bandgap copolymers, poly[{4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b:3,4-b']dithiophene-2,6-diyl}-alt-(2,2'-bithiazole-5,5'-diyl)] (PehCDT-BT), poly[(4,4-dioctyl-4H-cyclopenta[2,1-b:3,4-b']dithiophene-2,6-diyl)-alt-(2,2'-bithiazole-5,5'-diyl)] (PocCDT-BT), poly[{4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b:3,4-b']dithiophene-2,6-diyl}-alt-{2,5-di(thiophen-2-yl)thiazolo[5,4-d]thiazole-5,5'-diyl}] (PehCDT-TZ), and poly[(4,4-dioctyl-4H-cyclopenta[2,1-b:3,4-b']dithiophene-2,6-diyl)-alt-{2,5-di(thiophen-2-yl)thiazolo[5,4-d]thiazole-5,5'-diyl}] (PocCDT-TZ), for use in photovoltaic applications. The intramolecular charge-transfer interaction between the electron-sufficient CDT unit and electron-deficient bithiazole (BT) or thiazolothiazole (TZ) units in the polymeric backbone induced a low bandgap and broad absorption that covered 300 nm to 700-800 nm. The optical bandgap was measured to be around 1.9 eV for PehCDT-BT and PocCDT-BT, and around 1.8 eV for PehCDT-TZ and PocCDT-TZ. Gel permeation chromatography showed that number-average molecular weights ranged from 8000 to 14,000 g mol(-1). Field-effect mobility measurements showed hole mobility of 10(-6)-10(-4) cm(2) V(-1) s(-1) for the copolymers. The film morphology of the bulk heterojunction mixtures with [6,6]phenyl-C(61)-butyric acid methyl ester (PCBM) was also examined by atomic force microscopy before and after heat treatment. When the polymers were blended with PCBM, PehCDT-TZ exhibited the best performance with an open circuit voltage of 0.69 V, short-circuit current of 7.14 mA cm(-2), and power conversion efficiency of 2.23 % under air mass (AM) 1.5 global (1.5 G) illumination conditions (100 mW cm(-2)).

Visible-Light-Responsive High-Detectivity Organic Photodetectors with a 1 µm Thick Active Layer.

Organic photodetectors (OPDs) are attracting attention for use in flexible and portable electronic applications such as image sensors, remote sensing, optical communications, and medical sensors because of their strong photon responsivity in thin films over a broad range of wavelengths. In particular, the efficient photon-to-current conversion of OPDs under visible light allows their use in indirect X-ray detectors using scintillators to convert X-rays to visible light. The polymer poly(4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2- b:4,5- b']dithiophene- co-5-(2-hexyldecyl)-1,3-bis(6-octylthieno[3,2- b]thiophen-2-yl)-4 H-thieno[3,4- c]pyrrole-4,6(5 H)-dione) (PBDTT-8ttTPD) shows strong absorption bands in the region of 500-650 nm, as well as high hole mobility, which provides excellent photoresponsivity and photon-to-current conversion efficiency. A p-n junction photodetector was fabricated by blending PBDTT-8ttTPD and [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) and varying the thickness of the active layer (260-1100 nm). The PBDTT-8ttTPD:PC71BM-based OPDs show promising photodetecting properties having a low dark current of 3.72 × 10-9 A cm-2 and high responsivity of 0.39 A W-1 because of the well-controlled morphology, high molar absorption coefficient, and excellent carrier mobility of the PBDTT-8ttTPD:PC71BM layer. Consequently, the specific detectivity of the PBDTT-8ttTPD-based OPD devices was 1.13 × 1013 Jones at -2 V on irradiation with a light-emitting diode (530 nm wavelength) with a power density of 55.6 µW cm-2.