RESUMEN
An ultra-broadband TM-pass polarizer is designed, fabricated, and experimentally demonstrated based on subwavelength grating (SWG) metamaterials in a lithium niobate on an insulator (LNOI) platform. According to our simulation, the designed device is predicted to work at a 220â nm wavelength range from 1460 to 1680â nm, covering the S-, C-, L-, U-bands of optical fiber communication. By depositing and subsequently etching a silicon nitride thin film atop the LNOI chip, the SWG structures are formed successfully by using complementary metal-oxide semiconductor (CMOS)-compatible fabrication processes. The measured results show a high polarization extinction ratio larger than 20â dB and a relatively low insertion loss below 2.5â dB over a 130â nm wavelength range from 1500 to 1630â nm, mainly limited by the operation bandwidth of our laser source.
RESUMEN
BACKGROUND: The co-occurrence of chronic hepatitis B (CHB) and metabolic dysfunction-associated fatty liver disease (MAFLD) has drawn considerable attention due to its impact on disease outcomes. This study aimed to investigate the association between hepatic steatosis and hepatitis B virus (HBV) and analyzed the influence of hepatic steatosis on hepatitis B virology in patients with CHB. METHODS: In this cross-sectional study, 272 patients infected with HBV who were treatment-naïve or had ceased antiviral treatment for > 6 months were categorized into the CHB group (n = 128) and CHB + MAFLD group (n = 144). Furthermore, based on whether HBV DNA was higher than 2000 IU/mL, patients were categorized into the high-level HBV DNA group (n = 129) and the low-level HBV DNA group (n = 143). The impact of hepatic steatosis on hepatitis B virology was analyzed within the CHB cohort. Multivariate logistic regression analysis was employed to identify independent factors influencing pre-genomic RNA (pgRNA) levels below the lower limit of detection (LLD) in patients with CHB. RESULTS: Among the 272 patients, compared with CHB group, HBV DNA levels (4.11 vs. 3.62 log10 IU/mL, P = 0.045), hepatitis B surface antigen (HBsAg) levels (3.52 vs. 3.20 log10 IU/mL, P = 0.008) and the hepatitis B e antigen (HBeAg) positive rate (33.6% vs. 22.2%, P = 0.036) were significantly decreased in the CHB + MAFLD group; In 143 low-level HBV DNA patients, the CHB + MAFLD group exhibited decreased levels of pgRNA and HBsAg compared to the CHB group. However, in 129 high-level HBV DNA patients, a more significant decrease was observed in pgRNA (3.85 vs 3.35 log10 copies/mL, P = 0.044) and HBsAg (3.85 vs 3.59 log10 IU/mL, P = 0.033); Spearman correlation analysis revealed a negative correlation between hepatic steatosis and pgRNA (r = - 0.529, P < 0.001), HBV DNA (r = - 0.456, P < 0.001), HBsAg (r = - 0.465, P < 0.001) and HBeAg (r = - 0.339, P < 0.001) levels; Multivariate logistic regression analysis identified HBV DNA (odds ratio [OR] = 0.283, P < 0.001), HBsAg (OR = 0.300, P < 0.001), and controlled attenuation parameter (CAP) values (OR = 1.013, P = 0.038) as independent factors influencing pgRNA levels below the LLD in patients with CHB. CONCLUSIONS: This study establishes a negative correlation between hepatic steatosis and hepatitis B virology, demonstrating decreased HBV expression in patients with CHB + MAFLD.
Asunto(s)
Hepatitis B Crónica , Hepatitis B , Humanos , Virus de la Hepatitis B/genética , Antígenos de Superficie de la Hepatitis B , Antígenos e de la Hepatitis B , Estudios Transversales , ADN ViralRESUMEN
Ridge resonators are a recently introduced integrated photonic circuit element based on bound states in the continuum (BICs) which can produce a single, sharp resonance over a broad wavelength range with high extinction ratio. However, to excite these resonators, a broad beam of laterally unbound slab mode is required, resulting in a large device footprint, which is not attractive for integrated photonic circuits. In this contribution, we propose and numerically validate a guided-mode waveguide structure that can be analogue to the BIC-based ridge resonators. Our simulations show that the proposed guided-mode waveguide structure can produce resonances with similar characteristics, yet with a significantly reduced footprint. Furthermore, we investigate the influence of the resonator's dimensions on the bandwidth of the resonance, demonstrating that resonances with Q-factors from low to very high (> 10000) are feasible. We believe that the reduced footprint and ability to design filters systematically make the guided-mode waveguide resonators an attractive photonic circuit component with particular value for foundry fabricated silicon photonic circuits.
RESUMEN
Optical equalization can be used for chromatic dispersion compensation in optical communication systems to improve the system performance; however, optical signal processing (OSP) is generally specifically designed for transmission channels, that is non-adaptive to dynamic transmission distortions compared with digital signal processing (DSP). In this contribution, we demonstrate optical equalization using a photonic integrated circuit (PIC) filter for chromatic dispersion compensation, with static and adaptive techniques: (a) the static optical equalizer is calibrated based on the known fiber dispersion and length, by using the fractional delay reference method; (b) the adaptive optical equalizer is updated iteratively to compensate transmission impairments based on a least-mean squares (LMS) algorithm. Experimental results show that both the static optical equalizer and the adaptive optical LMS equalizer can give an 18-dB Q-factor for a 14-Gbd QPSK signal transmitting over 30 km. To highlight the capability of the optical equalizers, we use simulations to show the improvement in dispersion compensating characteristics by implementing additional taps.
RESUMEN
Reservoir computing is an analog bio-inspired computation scheme for efficiently processing time-dependent signals, the photonic implementations of which promise a combination of massive parallel information processing, low power consumption, and high-speed operation. However, most of these implementations, especially for the case of time-delay reservoir computing, require extensive multi-dimensional parameter optimization to find the optimal combination of parameters for a given task. We propose a novel, largely passive integrated photonic TDRC scheme based on an asymmetric Mach-Zehnder interferometer in a self-feedback configuration, where the nonlinearity is provided by the photodetector, and with only one tunable parameter in the form of a phase shifting element that, as a result of our configuration, allows also to tune the feedback strength, consequently tuning the memory capacity in a lossless manner. Through numerical simulations, we show that the proposed scheme achieves good performance -when compared to other integrated photonic architectures- on the temporal bitwise XOR task and various time series prediction tasks, while greatly reducing hardware and operational complexity.
RESUMEN
Lithium niobate on insulator (LNOI) platforms promise unique advantages in realizing high-speed, large-capacity, and large-scale photonic integrated circuits (PICs) by leveraging lithium niobate's attractive material properties, which include electro-optic and nonlinear optic properties, low material loss, and a wide transparency window. Optical mode interleavers can increase the functionality of future PICs in LNOI by enabling optical mode division multiplexing (MDM) systems, allowing variable mode assignment while maintaining high channel utilization and capacity. In this Letter, we experimentally demonstrate an optical mode interleaver based on an asymmetric Y-junction on the LNOI platform, which exhibits an insertion loss of below 0.46â dB and modal cross talk of below -13.0â dB over a wavelength range of 1500-1600â nm. The demonstrated mode interleaver will be an attractive circuit component in future high-speed and large-capacity PICs due to its simple structure, scalability, and capacity for efficient and flexible mode manipulation on the LNOI platform.
RESUMEN
Lithium niobate on insulator (LNOI) is a promising platform for high-speed photonic integrated circuits (PICs) that are used for communication systems due to the excellent electro-optic properties of lithium niobate (LN). In such circuits, the high-speed electro-optical modulators and switches need to be integrated with passive circuit components that are used for routing the optical signals. Polarization beam splitters (PBSs) are one of the fundamental passive circuit components for high-speed PICs that can be used to (de)multiplex two orthogonal polarization optical modes, enabling on-chip polarization division multiplexing (PDM) systems, which are suitable for enhancing the data capacity of PICs. In this Letter, we design and experimentally demonstrate a high-performance PBS constructed by a photonic crystal (PC)-assisted multimode interference (MMI) coupler. The measured polarization extinction ratio (ER) of the fabricated device is 15â dB in the wavelength range from 1525 to 1565â nm, which makes them suitable for the high-speed and large data capacity PICs required for future communication systems.
RESUMEN
We report on a low dark current density P-B-i-N extended short-wavelength infrared photodetector with atomic layer deposited (ALD) A l 2 O 3 passivation based on a InAs/GaSb/AlSb superlattice. The dark current density of the A l 2 O 3 passivated device was reduced by 38% compared to the unpassivated device. The cutoff wavelength of the photodetector is 1.8 µm at 300 K. The photodetector exhibited a room-temperature (300 K) peak responsivity of 0.44 A/W at 1.52 µm, corresponding to a quantum efficiency of 35.8%. The photodetector exhibited a specific detectivity (D ∗) of 1.08×1011 c mâ H z 1/2/W with a low dark current density of 3.4×10-5 A/c m 2 under -50m v bias at 300 K. The low dark current density A l 2 O 3 passivated device is expected to be used in the fabrication of extended short-wavelength infrared focal plane arrays for imaging.
RESUMEN
STATEMENT OF PROBLEM: The volume of occlusal adjustment of digital occlusal devices designed with different digital occlusal articulators is unknown. PURPOSE: The purpose of this clinical study was to evaluate and compare the clinical efficacy and volume of occlusal adjustment of digital occlusal devices designed by using an average value digital articulator and the jaw movement analyzer (JMA). MATERIAL AND METHODS: Thirty participants were randomly divided into 2 groups, an Average value group and a JMA group, with 15 participants in each group. The centric relation position of the participants was determined by an experienced investigator with the aid of a leaf gauge. An intraoral scanner (TRIOS 3) was used to obtain digital scans of the maxillary and mandibular dentition and the maxillomandibular relationship record in the centric relation position. Personalized articulator parameters of participants in the JMA group were obtained by using a JMA (JMAnalyser). Different articulator parameters were used to fabricate an occlusal device in a denture design software program (exocad DentalCAD). The surface of the occlusal device was coated with a dental optical spray and then scanned by using a laboratory scanner (Kavo LS3). The process was repeated after the occlusal device was adjusted. The files of the 2 scans were imported into a reverse engineering software program, and the root mean square (RMS) values were obtained by best-fit alignment and 3-dimensional comparison. The Shapiro-Wilk normality test and homogeneity of variance test were performed, and t tests were used to evaluate differences in the RMS values between the groups (α=.05). RESULTS: The experimental data were generally normally distributed (P>.05). No statistically significant difference was found between the RMS values of the Average and the JMA groups (P>.05). CONCLUSIONS: No significant difference in the volume of occlusal adjustment was found when using occlusal devices made by using the digital average articulator or the JMA, suggesting that either method can be used to program articulators for the fabrication of occlusal devices.
RESUMEN
Two-dimensional (2D) crystals are promising materials for developing future nano-enabled technologies1-6. The cleavage of weak, interlayer van der Waals bonds in layered bulk crystals enables the production of high-quality 2D, atomically thin monolayers7-10. Nonetheless, as earth-abundant compounds, metal oxides are rarely accessible as pure and fully stoichiometric monolayers owing to their ion-stabilized 'lamellar' bulk structure11-14. Here, we report the discovery of a layered planar hexagonal phase of oxides from elements across the transition metals, post-transition metals, lanthanides and metalloids, derived from strictly controlled oxidation at the metal-gas interface. The highly crystalline monolayers, without the support of ionic dopants or vacancies, can easily be mechanically exfoliated by stamping them onto substrates. Monolayer and few-layered hexagonal TiO2 are characterized as examples, showing p-type semiconducting properties with hole mobilities of up to 950 cm2 V-1 s-1 at room temperature. The strategy can be readily extended to a variety of elements, possibly expanding the exploration of metal oxides in the 2D quantum regime.
RESUMEN
The manipulation of optical modes directly in a multimode waveguide without affecting the transmission of undesired signal carriers is of significance to realize a flexible and simple structured optical network-on-chip. In this Letter, an arbitrary optical mode and wavelength carrier access scheme is proposed based on a series of multimode microring resonators and one multimode bus waveguide with constant width. As a proof-of-concept, a three-mode (de)multiplexing device is designed, fabricated, and experimentally demonstrated. A new, to the best of our knowledge, phase-matching idea is employed to keep the bus waveguide width constant. The mode coupling regions and transmission regions of the microring resonators are designed carefully to selectively couple and transmit different optical modes. The extinction ratio of the microring resonators is larger than 21.0 dB. The mode and wavelength cross-talk for directly (de)multiplexing are less than -12.8 dB and -19.0 dB, respectively. It would be a good candidate for future large-scale multidimensional optical networks.
RESUMEN
Oroxylin A, the main component of Scutellaria baicalensis Georigi has been widely studied due to its well-known pharmacological effects. According to previous studies, Oroxylin A with low bioavailability was converted into glucuronidation and sulphonated metabolites, which had high exposure in plasma and generated certain activities. It is necessary to study the metabolites and metabolic pathways of Oroxylin A.This study aimed to explore the metabolites of Oroxylin A in liver microsomes, primary hepatocyte incubation samples of five different species (human, monkey, dog, mouse, rat), and in bile, urine and faeces of rats.It would provide a systematic description of metabolic pathway of Oroxylin A. Also, a method of high-performance liquid chromatography combined with quadrupole time-of-flight mass spectrometry detector (HPLC-Q-TOF-MS/MS) for identification of each metabolite in various biological matrices was developed.This experiment illustrated that phase II metabolites were the main form of Oroxylin A in vitro and in excretion of rats, accompanied with a small amount of phase I metabolites.Furthermore, there were obvious species differences among the metabolism in vitro, especially in phase II. Monkeys and rats may be more suitable for preclinical research than dogs and mice as non-rodent or rodent species.
Asunto(s)
Neoplasias , Espectrometría de Masas en Tándem , Animales , Cromatografía Líquida de Alta Presión/métodos , Perros , Flavonoides , Ratones , Ratas , Ratas Sprague-Dawley , Espectrometría de Masas en Tándem/métodosRESUMEN
In this contribution we present a new approach to achieve high extinction short and long pass wavelength filters in the integrated photonic platform of lithium niobate on insulator. The filtering of unwanted wavelengths is achieved by employing lateral leakage and is related to the bound state in the continuum phenomenon. We show that it is possible to control the filter edge wavelength by adjusting the waveguide dimensions and that an extinction of hundreds of dB/cm is readily achievable. This enabled us to design a pump wavelength suppression of more than 100 dB in a 3.5 mm long waveguide, which is essential for on-chip integration of quantum-correlated photon pair sources. These findings pave the way to integrate multi wavelength experiments on chip for the next generation of photonic integrated circuits.
RESUMEN
In this paper, we propose and demonstrate a 4×4 non-blocking optical router utilizing 8 mode (de)multiplexers and a 4×4 microring-based grid network, which can passively assign signals carried by optical wavelength and mode channels from an arbitrary input port to corresponding output ports without additional switch time, realizing the non-blocking property. The proposed device is fabricated on a silicon-on-insulator platform using the standard Complementary Metal-Oxide-Semiconductor (CMOS) fabrication processes. The insertion loss is lower than 5.7 dB including the loss of the auxiliary mode (de)multiplexers (AMUXs), while the crosstalk is lower than -15.6 dB for all routing states. Moreover, the transmission spectra from the input ports to the next cascading device are also measured to demonstrate the feasibility of further expanding via cascading multiple blocks, with the insertion loss and crosstalk lower than 7.1â dB (including the mode coupling loss of AMUXs) and -16.4â dB, respectively. The 12 Gbps dynamic transmission experiment is demonstrated with clear and open eye diagrams, illustrating the utility of the device. The device has high geometrical symmetry and good scalability, we exhibit all solutions to expand the 4×4 optical router to 8×8 and 16×16 optical routers with the advantages and deficiencies of each solution discussed.
RESUMEN
Optical directed logic is a novel logic operation scheme that employs electrical signals as operands to control the working states of optical switches to perform the logic operations. In this Letter, we propose and demonstrate an integrated photonic circuit which can implement five different optical logic operations by utilizing two optical modes. The proposed device is fabricated on a silicon-on-insulator substrate by using electron beam lithography and inductively coupled plasma etching processes. The static experimental results show that the fabricated device can implement five different operations correctly-XOR, XNOR, NOR, NOT, and AND-from which we can see that the signal-to-noise ratios are larger than 17.6 dB over the entire C band for all five logic functions. At last, all five logic operations with the speed of 10 Kbps are demonstrated. The proposed device with simple structure, large bandwidth, and versatility would be a promising candidate for information processing in optical mode division multiplexing networks.
RESUMEN
Electro-optic (EO) modulators, which convert signals from the electrical to optical domain plays a key role in modern optical communication systems. Lithium niobate on insulator (LNOI) technology has emerged as a competitive solution to realize high-performance integrated EO modulators. In this Letter, we design and experimentally demonstrate a Mach-Zehnder interferometer-based modulator on a silicon nitride loaded LNOI platform, which not only takes full advantage of the excellent EO effect of LiNbO3, but also avoids the direct etching of LiNbO3 thin film. The measured half-wave voltage length product of the fabricated modulator is 2.24 V·cm, and the extinction ratio is â¼20dB. Moreover, the 3 dB EO bandwidth is â¼30GHz, while the modulated data rate for on-off key signals can reach up to 80 Gbps.
RESUMEN
Reversible H2 gas sensing at room temperature has been highly desirable given the booming of the Internet of Things (IoT), zero-emission vehicles, and fuel cell technologies. Conventional metal oxide-based semiconducting gas sensors have been considered as suitable candidates given their low-cost, high sensitivity, and long stability. However, the dominant sensing mechanism is based on the chemisorption of gas molecules which requires elevated temperatures to activate the catalytic reaction of target gas molecules with chemisorbed O, leaving the drawbacks of high-power consumption and poor selectivity. In this work, we introduce an alternative candidate of cobalt oxysulfide derived from the calcination of self-assembled cobalt sulfide micro-cages. It is found that the majority of S atoms are replaced by O in cobalt oxysulfide, transforming the crystal structure to tetragonal coordination and slightly expanding the optical bandgap energy. The H2 gas sensing performances of cobalt oxysulfide are fully reversible at room temperature, demonstrating peculiar p-type gas responses with a magnitude of 15% for 1% H2 and a high degree of selectivity over CH4, NO2, and CO2. Such excellent performances are possibly ascribed to the physisorption dominating the gas-matter interaction. This work demonstrates the great potentials of transition metal oxysulfide compounds for room-temperature fully reversible gas sensing.
RESUMEN
Data exchange between different data channels can offer more flexible and advanced functions for many optical networks. In this paper, we propose a switchable and reconfigurable data exchange device for arbitrary two optical mode channels based on three-waveguide-coupling (TWC) switches in mode-division multiplexing (MDM) networks. The working principle of the TWC switches is numerically analyzed using the coupled supermode theory. As a proof of concept, switchable data exchange between arbitrary two mode channels among the first three-order quasi-transverse electric modes is experimentally demonstrated successfully. The insertion losses of the device are less than 5.6 dB, including the coupling loss of the multiplexer and demultiplexer, while the mode crosstalk is less than -13.0 dB for all functions. The proposed device is expected to offer more flexibility to on-chip MDM networks due to its low loss, low crosstalk and good scalability.
RESUMEN
An on-chip biochemical sensor based on two-dimensional waveguide-integrated plasmonic crystal formed by a nanogap tile (NGT) array is realized. By using on-chip optical lenses, an ultra-wide collimated Gaussian beam is launched, coupled with surface plasmonic crystals and collected with relatively low additional insertion loss, allowing a large sensing area. The optical field enhancement and stop-band shift of the NGT device for biochemical sensing are numerically and experimentally demonstrated with sensitivity reaching up to ${\sim}{260}\;{\rm nm/RIU}$â¼260nm/RIU. Our sensor is demonstrated with monolayer thiol molecules illustrating that it can be functionalized with this class of molecule which is commonly used with bulk surface plasmon resonance sensors.
Asunto(s)
Técnicas Biosensibles/métodos , Silicio/química , Distribución Normal , Fenómenos Ópticos , Compuestos de Sulfhidrilo/análisisRESUMEN
PURPOSE: Our aim was to evaluate the influence of genetic polymorphisms involved in the metabolism and transportation of deferasirox on deferasirox pharmacokinetics in the Chinese population. METHODS: Thirty-eight healthy Chinese subjects were administered with a single dose of 20 mg kg-1 deferasirox. Allelic discriminations for eight single-nucleotide polymorphisms (SNPs) in UDP-glucuronosyltransferase 1A1, 1A3 (UGT1A1, UGT1A3), multidrug resistance protein 2 (MRP2, ABCC2), and breast cancer resistance protein (BCRP, ABCG2) were performed. The concentrations of deferasirox in the plasma were determined by UPLC-MS/MS. RESULTS: Subjects carrying ABCC2 c.-24 T allele had a 65% higher clearance (CL/F) and 42% lower area under the concentration-time curve from 0 to 72 h (AUC0-72h) as compared with non-carriers (P = 0.008, P = 0.011, respectively). ABCC2 c.-24 T was also associated with 59% shorter half-life (T1/2) and 17% shorter mean residence time (MRT) (P = 0.030, P = 0.014, respectively). ABCC2 1249A was associated with a marginal increase in deferasirox Cmax (P = 0.07). Genetic polymorphisms of UGT1A1, UGT1A3, and ABCG2 did not significantly influence the pharmacokinetics of deferasirox. Subjects with UGT1A1 211GG-(-1352)CC-(-3156)GG haplotype had higher AUC0-72h than others. Since only two subjects were recruited in the GG-CC-GG group, further confirmative studies were warranted. CONCLUSIONS: ABCC2 c.-24 C>T was associated with the pharmacokinetic variability of deferasirox in Chinese subjects. This study revealed an important role of MRP2 in the pharmacokinetics of deferasirox and drew attention to drug combination with MRP2 inhibitors like cyclosporine and methotrexate in deferasirox therapy.